Automatic detection of washboarding in bandsaws

This paper presents an on-line method for detecting washboarding generated in bandsaws. It uses a parameter based on the shape of sawing force amplitude distributions. The curve of the probability density function of the parallel sawing force amplitude obeyed a normal distribution for the normal sawn surface, but it changed to an M-shaped distribution when washboarding appeared on the sawn surface of the workpiece. The curve of probability density function of the normal sawing force amplitude obeyed the normal distribution for any sawn surface investigated. The workpiece including a knot did not influence use of the parameter for detecting the appearance of washboarding.     

Vertical profiles of environmental factors within tropical rainforest, Lambir Hills National Park, Sarawak, Malaysia

Environmental factors, such as global solar radiation, wind speed, air temperature, humidity, and CO₂ concentration, were measured above and within the canopy of a tropical rainforest in Lambir Hills National Park, Sarawak, Malaysia. Few data concerning the environment of this forest have been reported. Intensive observations were carried out in 1998, 1999, and 2000 with the following results: (1) The fraction of global solar radiation reaching the upper layer of the canopy varied with global solar radiation above the canopy. Even though the global solar radiation above the canopy fluctuated, the fraction of that reaching the lower canopy and the ground was constantly approximately 5%. (2) The fraction of wind speed reaching each layer of the canopy increased with wind speed above the canopy. Little wind was usually present at the lower canopy. (3) The daytime air temperature at the canopy top was higher than that near the ground. The maximum difference between the air temperature at the canopy top and that at the ground was about 5°C, and the diurnal temperature ranges at the canopy top and those at the ground were about 8°C and about 5°C, respectively. The highest daytime water vapor pressure occurred within the canopy and particularly near the ground. Vertical gradients of water vapor pressure during the day were steep, probably because of high transpiration. (4) In the 1998 observation the minimum and the maximum CO₂ concentrations were 360 ppm in the day and 450 ppm at night, while in the 2000 observation the minimum and the maximum CO₂ concentrations were 350 ppm in the day and 540 ppm at night. The higher CO₂ concentration in the daytime and the lower concentration at night observed during the 1998 observation period were probably due to reduced photosynthesis and soil respiration caused by exceptional dry conditions during the observation period.     

High-speed steel tool wear during wood cutting in the presence of high-temperature corrosion and mineral contamination

Dulling of high-speed steel (HSS) cutting tools after milling five wood species has been analyzed. The wood investigated varied in mineral contamination, high-temperature corrosivity (HTC) and density (D). Experiments performed proved that up to date methods for evaluation of mineral contamination in wood should be improved. A new pipe-like form of mineral contamination particles was evidenced. The correlation between the presence of 3D aggregates of silica in wood and high content of K and Ca in the ash was established. Employing multivariable theoretical simulation method, the combined effect of mineral contamination, HTC and wood density on the tool dullness appeared to be a reasonable explanation of the results obtained.     

Simple method for synthesizing phenolicβ-O-4 dilignols

A modified synthetic method for phenolic-O-4 lignin substructure model dimers was developed involving protection of the phenolic hydroxyl group of acetophenons with benzoyl chloride, bromination with 4-dimethylaminopyridiniumbromide perbromide, condensation with phenols in the presence of 18-crown-6-ether, condensation with paraformaldehyde, reduction with NaBH₄ and debenzoylation. This method results in shorter reaction times and increasing yields without the application of strict anhydrous and drastic conditions or chloric solvents. This alternative route could be applied to the-O-4 dilignol syntheses of four combinations of guaiacyl and syringyl derivatives.     

Effect of tool angles on the chips generated during milling of wood by straight router-bits

 The effect of tool angles on the shapes of chips generated by parallel-to-grain and end-grain milling was explored for China fir and maple under fixed spindle and feed speeds and cutting depth. The milling path was up-milling by straight router-bits with a diameter of 12 mm. The chip shapes could be distinguished as five types: spiral, splinter, flow, thin, and granules or powder. The flow and thin chips were generated most often (on a weight percentage basis) for all tool angles investigated for parallel-to-grain and end-grain milling of China fir and maple. More granule chips were produced with parallel-to-grain milling than with end-grain milling for both woods. The measured chip thickness (t′) was thicker than the calculated thickness (t _max). Thicker and longer maple chips were produced by end-grain milling than by parallel-to-grain milling. The tool geometries of 40°/15° (sharpness of the angle–rake angle), 50°/15°, and 60°/15° for China fir and 40°/25°, 50°/5°, and 60°/5° for maple produced relatively more flow chips with parallel-to-grain milling. Furthermore, the tool geometries of 40°/5°, 50°/15° and 60°/25° produced more flow chips (weight percentage) by end-grain milling of China fir and maple. Received: May 23, 2001 / Accepted: June 28, 2002 Acknowledgment This study was supported by a grant from the National Council of Science, Taiwan (NSC89-2313-B-415-011).     

Maternal Liver Damage Delays Meiotic Resumption in Bovine Oocytes through Impairment of Signalling Cascades Originated from Low p38MAPK Activity in Cumulus Cells

The main objective of the present study is to investigate the molecular mechanism underlying the delay in progression of nuclear maturation in oocytes derived from cows with damaged livers (DL cows), which was previously reported. In present study, delayed progression of nuclear maturation of oocytes derived from DL cows relative to oocytes derived from cows with healthy livers (HL cows) was accompanied by low maturation promoting factor (MPF) activity (0.43 fold, p < 0.05). When cumulus cells were removed from cumulus‐oocyte complexes and the denuded oocytes were cultured, there was no difference in the progression of nuclear maturation between the two liver conditions. In addition, gap junctional communication (GJC) between the oocyte and cumulus cells was higher in DL cows than in HL cows at 3 and 7 h of in vitro maturation (IVM) (p < 0.05). Supplementation of IVM medium with epidermal growth factor (EGF) increased the ratio of germinal vesicle breakdown (GVBD) of oocytes derived from DL cows to the level seen in oocytes derived from HL cows. Additionally, the level of p38MAPK phosphorylation at 0 h of IVM was significantly lower in cumulus cells derived from DL cows than in cumulus cells derived from HL cows (HL cows, 53.5%; DL cows, 28.9%; p < 0.05). Thus, a low level of p38MAPK phosphorylation in cumulus cells induced slow GJC closure between oocyte and cumulus cells, which resulted in slow meiotic maturation of oocytes derived from DL cows.     

Applicability of effective medium theory to wood density measurements using terahertz time-domain spectroscopy

The use of an effective medium theory is important when accurately measuring wood density using millimeter and terahertz wave techniques. To confirm the applicability of this theory to the evaluation of wood density, the relative permittivity and dielectric loss of oven-dry flat-sawn specimens of 11 different wood species were measured in a frequency range of 0.15–1.2 THz using a transmission measurement system for terahertz time-domain spectroscopy. A mixture model based on the effective medium theory well explained the density dependence of relative permittivity over the entire frequency range, while it did not fully explain that of dielectric loss, especially for higher frequencies. This indicates that wood scatters the terahertz wave with a wavelength close to the transverse sectional dimensions of the pores in wood in the same way as Mie scattering. It was found from the dielectric loss spectrum of wood substance that the frequency around 0.23 THz was preferable for the nondestructive evaluation of wood.     

Effect of pore conformation on dielectric anisotropy of oven-dry wood evaluated using terahertz time-domain spectroscopy and eigenvalue problems for two-dimensional photonic crystals

To clarify the effect of pore conformation on the dielectric anisotropy of wood, the relative permittivity along the longitudinal and tangential axes of flat-sawn oven-dry specimens of 12 different wood species was measured using terahertz time-domain transmission spectroscopy and compared with the values calculated using the eigenvalue problem for two-dimensional photonic crystals. The measured dielectric anisotropy, which is the ratio of the relative permittivity along longitudinal axis to that along the tangential axis, was well explained by the calculated value. It was concluded that the ratio of tangential to radial widths of wood pores affects the relative permittivity along the tangential axis, and that the dielectric anisotropy decreased with an increase in the ratio. This discussion can also be applied to the relative permittivity in frequencies below 0.15 THz. These findings show promise as a new method for evaluating the porous structure of wood.