Directly-prelithiated carbon nanotube film for high-performance flexible lithium-ion battery electrodes

Carbon nanotube (CNT) films are very flexible and serve as active materials for lithium-ion batteries (LIBs). Hence, they have high potential as flexible free-standing electrodes for wearable batteries. However, nanocarbon materials such as CNTs and graphene are of limited use as electrodes because they have a large initial irreversible capacity due to the formation of a solid electrolyte interphase (SEI). Herein, we prelithiated the CNT films to make them available as electrodes for flexible batteries by reducing their irreversible capacity. The SEI is pre-formed through a direct prelithiation (DP) method that brings lithium metal into direct contact with CNT films in an electrolyte. As a result, the capacity of directly-prelithiated CNT film electrodes continues to increase to 1520 mAh/g until 350th cycle of charge/discharge and their initial irreversible capacity vanishes. The changes in the electrochemical properties of CNT film electrodes by DP treatment and their flexibility are investigated.     

Isolation and characterization of nanocrystalline cellulose from different precursor materials

Nanocrytalline cellulose (NCC) was isolated using cellulose extracted from two different precursor materials: Eucalyptus globulus and rice straw. The two ground precursor materials were autoclaved with a 10 % NaOH solution at 120 °C for 3 h. The alkali-treated precursor materials were bleached using sodium chlorite/acetic acid and sodium hypochlorite. The bleached precursor materials were acid-hydrolyzed in 65 % (w/w) sulfuric acid at 45 °C for 30-120 min. The changes in the chemical composition of the two precursor materials were studied before and after bleaching by Fourier transform infrared spectroscopy according to the NREL report and TAPPI standards. Hydrolyzates were characterized by X-ray diffractometry, thermogravimetric analysis, Zeta-potential analysis, and transmission electron microscopy. The results revealed that the physical properties of NCC were strongly dependent on the acid-hydrolysis time.     

LED-UV grafting of vinylsulfone dyes onto photo-oxidized wool fabrics

Photografting coloration of wool was carried out under UV-LED irradiation at room temperature using aqueous vinylsulfone dye solution containing vinylsulfonic acid as a comonomer. UV-LED irradiation of the 395 nm emission is more energy efficient, less damaging to the dyes, and much safer to human eyes compared with polychromatic mercury UV lamps. However, in case of the UV-LED lamps, the wool needs to be photo-oxidized either by UV/ozone or polychromatic UV irradiation before the dye photografting. The surface treatments increased the sulfur and oxygen contents in the modified wool surfaces. While the optimally photografted wool fabrics under the UV-LED lamp yielded a K/S value of 9.9, the K/S of the grafted wool increased to 25.2 and 13.6 after the UV/Ozone or polychromatic UV preoxidation at UV energies of 10.6 J/cm² and 25 J/cm² respectively. The color fastness properties of the photografted fabrics were far better than with those of the conventionally reactive-dyed fabrics, implying that the high-molecular-weight photografted dyes seemed to be more durable than the low-molecular dyes.     

Properties of polymers as a nanoscale material for fibers in leather

Hyperbranched polymers, an innovative class of nano-polymers, could enhance the properties of fibers owning to their unique structures. In this study, the ester compound (HPAE) of 3-(bis(2-hydroxyethyl)amino)propionic acid and pentaerythritol was treated with undecylenic acid to obtain novel hyperbranched multiterminal alkenyl polymers (HPAE-UAs). The sizes of the HPAE-UAs could be controlled conveniently from 400 to 1300 nm by adjusting the capped fraction of the hydroxyl groups with undecylenic acids. The molecular structures of HPAE-UAs were characterized by means of FT-IR and ¹H-NMR. Then, the effect of the HPAE-UAs on the structures, thermal, and mechanical properties of the wet blue leather were investigated. TEM and SEM demonstrated that the spacing between fibers was enlarged. The thermogravimetric analysis showed that the residual volume of leather could reach up to 30.3 % at about 500 °C. Furthermore, the shrinkage temperature increased to 89.4 °C. It was found that the HPAE-UAs used in leather could improve the thermal performance, physical and mechanical properties. All of these results indicate that HPAE-UAs can be used as a fatliquor with retanning in leather process.     

Polyvinylidene fluoride nanofiber coated polypropylene nonwoven fabric as a membrane for lithium-ion batteries

Polyvinylidene fluoride (PVdF) membranes in spite of having many critical properties necessary for lithium-ion batteries, do not have satisfying thermal and mechanical resistance. The goal of this study was to combine the good mechanical and thermal properties of PP nonwoven fabric with the excellent electrochemical properties of PVdF nanofibers to exploit a high-performance membrane for lithium-ion batteries. This work reports the preparation of PVdF nanofiber membranes using electrospinning on a polypropylene (PP) spunbonded nonwoven fabric and an aluminum foil followed by a hot-pressing treatment. The morphology and size of the membranes were studied by the scanning electron microscopy. The tensile strength of the membrane with the PP support was superior to the PVdF membrane. Thermal stability of the prepared membranes was determined using the TGA method and the dimensional stability was investigated by measuring the shrinkage ratio at 105 °C. The results have shown that the PVdF/PP membrane was thermally more stable than the PVdF and the commercial Celgard 2325 membranes. The batteries using PVdF/PP membrane exhibited higher electrochemical oxidation limit, better cycling performance and less discharge capacity fading during 100 cycles compared to PVdF and Celgard membranes. The results of this study showed that PVdF/PP membrane is a promising advanced membrane in lithium-ion batteries.     

Preparation and properties of solid polymer electrolyte based on imidazolium-based ionic liquids for structural capacitors

We prepared solid polymer electrolytes (SPEs) composed of poly(ethylene glycol) monomethyl ether acrylate (1A9OMe) and 1-ethyl-3-methylimidazolium trifluoromethanesulfonate ([EMIm][OTF]) and 1-ethyl-3-methylimidazolium bis(trifluoromethane sulfonyl) imide ([EMIm][TFSI]) as the ionic liquid. The SPEs formed by appropriately adding ionic liquids in the 1A9OMe prior to thermal cure. The ratio of 1A9OMe and ionic liquid was 1:9, 3:7, and 5:5, respectively. The characterization of solid polymer electrolytes were investigated using Fourier transform infrared spectroscopy in the attenuated total reflectance mode (FTIR-ATR), Electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and glavanostatic charge-discharge test. The highest ionic conductivity of SPEs was found to be 4.90×10^?4 S/cm in a 1A9OMe/[EMIm][OTF] of 3:7. As IL contents were increased, the specific capacitance of supercapacitor was increased. The specific capacitance of supercapacitor for ionic liquid with large ion size was lower than that for ionic liquid with smaller ion size.     

Synthesis of hydrophobic anthraquinoid magenta dyes having linear alkyl substituents

A new series of magenta dyes having different length of alkyl substituents was synthesized to dye unmodified polypropylene (PP) and ultra-high molecular weight polyethylene (UHMWPE) fiber. It could be concluded that the affinity of the dyes onto unmodified PP and UHMWPE fibers was increased with the increase of the length of alkyl substituents. The optimum length of alkyl group was determined as the longest dodecyl-substituted dye in this study. Their absorption spectra appeared almost the same at visible range, which meant that the length of alkyl substituents did not affect the color appearance of the dyes. The color fastness properties of the dyeings to washing, rubbing and light were good enough for commercialization.     

Copolymerization of benzyl methacrylate and a methacrylate bearing benzophenoxy and hydroxyl side groups: Monomer reactivity ratios,thermal studies and dielectric measurements

Statistical copolymers of 2-hydroxy-3-benzophenoxy propyl methacrylate (HBPPMA) and benzyl methacrylate (BzMA) in different feed ratios were synthesized by free radical copolymerization method at 60 °C in presence of AIBN initiator. The compositions of copolymer were estimated from ¹H-NMR technique. The monomer reactivity ratios of HBPPMA and BzMA were calculated as r₁ (r_HBPPMA)=0.51±0.076 and r₂ (r_BzMA)=1.07±0.140 for Kelen-Tüdos method, and was estimated as r₁=0.37±0.0006 and r₂=0.64±0.0485 according to Fineman Ross equation. The average values estimated from the two methods showed that monomer reactivity ratio of benzyl methacrylate was a slightly high in comparison to HBPPMA. The copolymer system showed an azeotropic point, which is equal to M _BzMA =m _BzMA =0.43. DSC measurements showed that the T_g’s of poly(HBPPMA) and poly(BzMA) were 84 °C and 73 °C, respectively. The T_g in the copolymer system decreased with increase in benzyl methacrylate content. The decomposition temperature of poly(BzMA) and poly(HBPPMA) occurs in a single stage at about 207 °C and 260 °C, respectively. Those of HBPPMA-BzMA copolymer systems are between decomposition temperatures of two homopolymers. The dielectric constant, dielectric loss factor and electrical conductivity were investigated depend on the frequency of the copolymers. The highest dielectric constants depending on all the studied frequencies were recorded for the poly(HBPPMA) and the copolymer containing the highest HBPPMA unit. The dielectric constant for P(HBPPMA) and P(BzMA) at 1 kHz are 6.56 and 3.22, respectively. Also, those of copolymer systems were estimated between these two values. Similarly, poly(HBPPMA) and copolymers, which are prepared under the same conditions show the dissipation factor and conductivity as well.     

Numerical analysis of injection molding for the Syringe Barrel with optimum design and processing condition

The numerical analysis was performed to predict the potential problem, often occurring during the manufacturing process of the disposable medical device of a great volume. The cavity filling analyses were performed for the new design of the 3cc Syringe Barrel using polypropylene(PP1), and a new nucleated polypropylene(PP2) material for better clarity. These analyses have been performed for different processing conditions as well as various wall thickness designs for both materials. With the nucleated material, only the original wall thickness design has been studied at two different processing conditions for comparison purpose. This study was conducted to investigate the optimum part design and processing condition for two different materials. The most desirable design was selected with Design 3 for material utilization and reduced flow stresses by comparing the field results. The new nucleated polypropylene provided slightly better product quality and processing.     

Synthesis,characterization and ultrafiltration of reactive dyes. Application by exhaustion and/or ink-jet printing. IV.

Three new bis azo reactive dyes of different metallic salts (Na, K, Li) were synthesized. The synthesis was obtained by diazotization of 4-amino-2:5 di methoxy phenylene-beta hydroxyl ethyl sulphone sulphate ester and coupling with 1-amino-8-hydroxynaphthalene-3,6-disulfonic acid (H-acid) (moles ratio 2:1). The dyes were purified-concentrated by ultrafiltration technology, characterized and applied on cotton, wool and nylon 6,6 fabric by exhaustion (dyeing) and by ink-jet printing. Fastness properties of the dyeings were measured. Wash fastness was investigated according to international standard methods and was found to be very good to excellent in all cases, while light fastness values were medium to low. Ink-jet ink formulations were prepared using the ultra filtrated reactive blue dyes UF RB(a-c) and their properties pH, conductivity, surface tension and viscosity were monitored over a period of 90 days. The inks were used to print digitally cotton and nylon 6,6 samples and wash- and light fastness properties of the prints were measured. Wash fastness properties were excellent while light fastness values are low Colour measurements of the dyeings and prints were conducted.