Performance of particleboard manufactured using air-injection press II: effects of board density and thickness on the performance of board manufactured from low-moisture particles

Particleboards of different densities (0.6, 0.7 and 0.8 g/cm³) and thicknesses (10 and 20 mm) were manufactured from low-moisture particles using an air-injection press. The effects of the air injection on preventing blowout of the boards of different densities and thicknesses were investigated by artificially creating blowout-prone conditions using metal frames. The effects of the air-injection pressure on the board performance were also investigated. 10-mm-thick boards of 0.8 g/cm³ pressed at 170 °C blew out when air was not injected, but were successfully manufactured by injecting air. 10-mm-thick boards at 150 °C showed constant internal bond (IB), regardless of density, but at 170 °C, IB was higher in boards of higher densities. This was likely due to accelerated hardening of the urea–formaldehyde resin at 170 than 150 °C. At both pressing temperatures, low air-injection pressure did not cause blowout and a reduction in board performance. Air injection also prevented the blowout of thick boards of 20 mm and enabled successful manufacture, showing its effectiveness. The IB of the 20-mm-thick board manufactured using the air-injection press exceeded that of 20-mm-thick board manufactured using an ordinary hot press.     

Automatic detection of washboarding in bandsaws

This paper presents an on-line method for detecting washboarding generated in bandsaws. It uses a parameter based on the shape of sawing force amplitude distributions. The curve of the probability density function of the parallel sawing force amplitude obeyed a normal distribution for the normal sawn surface, but it changed to an M-shaped distribution when washboarding appeared on the sawn surface of the workpiece. The curve of probability density function of the normal sawing force amplitude obeyed the normal distribution for any sawn surface investigated. The workpiece including a knot did not influence use of the parameter for detecting the appearance of washboarding.     

The effect of tractor logging on forest soil compaction and growth ofShorea selanica seedlings in Indonesia

The hardness in soil was investigated in four forest areas in Indonesia after a crawler tractor passed over it several times. The hardness in soil, expressed by bulk density, was measured at various depth and various distances from the main track. Recovery of soil hardness was also examined. The bulk density increased markedly by the first and second pass of the tractor, but did not change after the fifth pass. The bulk density was highest just under the main and the log track, and decreased with an increase in distance from the track (0.5 to 1.5 m). The greatest increase in bulk density was observed at the depth of 0–5 cm. The soil hardness tended to show recovery within 9 years after logging, though not completely. Growth and root penetration of seedlingsShorea selanica decreased with the increase of soil hardness. We considered that the 2 tractor passes that caused bulk density of 1.3 g/cm³ is critical for the growth ofS. selanica’s seedling.     

Impregnation of radiata pine wood by vacuum treatment II: effect of pre-steaming on wood structure and resin content

Radiata pine sapwood and heartwood were dried using high-temperature, conventional-temperature, and air drying schedules with and without pre-steaming. They were then impregnated by vacuum treatment with double-distilled water, toluidine blue, and fluorescein dye. For sapwood, there were only minor differences in uptake between drying methods and when pre-steaming was used. Using microscopy, the primary flow pathways in sapwood were found to be the resin canal network and ray parenchyma cells, which provided conduction without large resistance. In heartwood, uptake was strongly influenced by pre-steaming the green lumber. After pre-steaming heart-wood, there was an increase in uptake from all surfaces but especially from the radial surfaces. Lower extractive contents, disruption of epithelial and ray parenchyma cells, and alteration of the condition of bordered pits were also associated with pre-steaming. It was therefore possible to classify flow paths in radiata pine heartwood five ways, according to uptake values and wood anatomical features.This research was presented in part at the 48th annual meeting of the Japan Wood Research Society, Shizuoka, April 1998.     

Accuracy of shear properties of wood obtained by simplified Iosipescu shear test

We examined the accuracy of the shear properties of wood by the Iosipescu shear test using specimens whose shape was simplified. Quartersawn boards of sitka spruce (Picea sitchensis Carr.) and shioji (Japanese ash,Fraxinus spaethiana Lingelsh.) were used. Two types of specimen for the Iosipescu shear test were compared: a standard specimen whose notch angle is 90° and a keyhole type specimen, which is more easily prepared than the standard type. The shear modulus, yield shear stress, and failure shear stress of the keyhole-type specimen were compared to those of the standard specimen. Shear stress analysis was conducted using the finite element method (FEM). The results obtained were as follows: (1) The failure pattern obtained by the simplified Iosipescu shear test was similar to that seen with the standard Iosipescu shear test. (2) The shear modulus, yield stress, and failure stress obtained by the simplified Iosipescu shear test coincided with those by the standard Iosipescu shear test. (3) The principal strain angle and principal stress angle of the simplified Iosipescu shear test were about 45°. (4) It is recognized that pure stress is applied to the strain-gauge regions in the simplified Iosipescu shear test, and it is expected that the shear properties are independent of the notch angle.     

Automatic detection of a damaged cutting tool during machining I: method to detect damaged bandsaw teeth during sawing

This paper presents an on-line method for detecting damaged teeth in the bandsaw using acoustic emission (AE) signal energy. The method is based on an analysis of differences in AE energies generated by normal and damaged teeth during sawing. Because of the difference in the amount of sawing, the AE energy was low for sawing by the damaged tooth and high for sawing by the normal tooth immediately after the damaged tooth. The ratio of AE energy for two successive teeth — a normal tooth immediately following a damaged tooth — was much greater than 1, whereas the ratio of AE energy for two successive normal teeth was close to 1. The results demonstrate that the technique using the AE energy ratio for two successive teeth is effective for on-line detection of damaged bandsaw teeth.Part of this paper was presented at the 9th Annual Meeting of the Chugoku Skikoku Branch of the Japan Wood Research Society, Tottori, October 1997     

Behavior of four broad-leaved tree species used to revegetate eroded granite hill slopes

Information on primary growth behavior after planting is required for mixed-plantation revegetation using broad-leaved species. To estimate primary growth, especially from the perspective of crown coverage and changing growth rates, we examined the growth and survival of four broad-leaved species that are frequently used in erosion-control plantations in Japan. The species studied were Myrica rubra Sieb. et Zucc., Alnus pendula Matsum., Quercus glauca Thunb., and Q. serrata Thunb. The survival, height, and basal diameter of planted trees were measured over a 4-year period, and crown area was calculated over a 3-year period. We found a negative relationship between relative growth rate (RGR) and survival rate, suggesting that fast growth may be fatal when resources are severely limited. The relative height growth rate (RHGR) of A. pendula was especially high during the early period of the study (1997–1999) and then drastically declined, whereas the opposite tendency was observed in Q. glauca. The results of stem allometry analyses conformed to the specific relationships between height growth and diameter growth of the four species; increases in stem thickness based on height increments were smaller in the pioneer species A. pendula. Between-species differences in coverage per planted tree (mean crown area multiplied by survival rate) were small as a result of the negative relationship between coverage area and survival rate.     

Leaf-fall phenology along a topography-mediated environmental gradient in a cool–temperate deciduous broad-leaved forest in Japan

Leaf-fall phenology was studied in a cool–temperate deciduous broad-leaved forest in central Japan in relation to the topographic environmental gradients that occur along a short mountain slope. Leaf-fall phenology was described quantitatively using data from leaf litter collected along the slope. In autumn, leaf fall at the study site tended to occur slightly earlier on the upper slope than on the lower slope. This pattern was found at both the stand and the species levels. Our results suggest that leaf-fall phenology may be affected by difference in microclimatic conditions, because environmental conditions are thought to be more severe on the upper slope than on the lower slope. The less intensive methods used in this study, the litter trap method, and Dixon’s model succeeded in quantifying the phenological patterns of leaf fall within stands and within species along the short mountain slope.     

Assignment of the 1H and 13C NMR spectra of 2-aminobenzamide-labeled galacto- and arabinooligosaccharides

1,4-Linked β-d-galactooligosaccharides with a degree of polymerization (DP) between 1 and 7 and 1,5-linked α-l-arabinooligosaccharides with a DP between 1 and 8 were labeled at their reducing ends with 2-aminobenzamide (2AB) in the presence of sodium cyanoborohydride. The 2AB-labeled oligosaccharides were shown to be homogeneous using high-performance anion-exchange chromatography (HPAEC) and by electrospray ionization mass spectrometry (ESI-MS). The signals in the ¹H and ¹³C nuclear magnetic resonance (NMR) spectra of the 2AB-labeled oligosaccharides were then assigned using one- and two-dimensional NMR spectroscopy. These NMR data will be useful for the structural analysis of enzymatically synthesized galactan and arabinan side chains derived from rhamnogalacturonan I.