Portable ECG Monitor Front- ended Design with C8051 F020

The electrocardiogram (ECG) signal is a recording of the electrical activity on the body surface generated by the heart frequency of which is weak and low. Many researchers devote themselves to get more perfect ECG in many ways. This article introduces the characterize of an ECG signal , then discusses the requirements for the sampling circuit of an ECG. Since there are some shortcoming in common design means, the authors give an effective circuit. The system is composed of a low-cost , low-power and high-performance MCU C8051F020 , amplifier AD620 , right-leg drive circuit ,communication circuit and power management circuit. Then software design is given which is used to sampling and filtering ECG signal. Levkov filter arithmetic and smooth filter arithmetics are used in this design. In the end , the authors advance a distributing and networking ECG monitor system.     

A Study on the Model of Surface Storm-Water Runoff at Urban Gully

On the assumption that the runoff on the catchment of each gully flows into the gully itself, in this paper, a model of surface storm-water runoff at urban gully is presented, which includes runoff sub-model and concentration sub-model.The runoff sub-model describes the rainfall event with instantaneous rainfall intensity, the runoff-generated event with runoff coefficient of integrative area and the runoff converged event with the principle of equal time of flowage.The concentration sub-model shows that the pollutant concentration event only changes with the runoff event at the gully.In this paper, the concrete form of the model for two gully inlets in Shapingba District of Chongqing is given.The model is calibrated with the data from the synchronized measurements of water quantity and quality at the two gully inlets obtained from July to September 2000.The relative error is calculated by comparing the model predictions with the field-measured results.     

Structural Analysis and Discussion of Wide -stayed Bridge Basket

Based on a cable -stayed bridge girder as an example, the structure and function, the operating principle and calculation model of the main elements of the Basket of wide - stayed bridge were described in detail. A further discussion was carried out on the Basket of Cantilever construction of the main beam in the structure.     

基于稻草制造钵育秧盘水稻栽植机的研究

以稻草(植质)为原料,研制出水稻钵育秧盘。在以稻壳粉与土为原料混合研制人工苗床土的基础上,按基于稻草制造钵育秧盘水稻乳苗机械栽植技术的要求,设计和试制了水稻钵育乳苗栽植机,并进行了生产性试验,证明了该项技术是可行的。     

煤与生物质恒温热解比较研究

在实验室自制固定床热解反应器中,选择了两种煤(神华煤和灵武煤)和3种生物质(花生壳、核桃壳和木屑)作为实验材料,定量化分析比较了恒温热解和同温热解停留时间对煤与生物质热解产氢及热解油、热解焦产率的影响.研究认为:实验用煤与生物质催化热解表现出基本相同的热解趋势,即提高热解温度和延长热解时间(对生物质添加合适催化剂)都有利于产氢;对煤而言,提高热解温度和延长热解时间还利于热解油生成,但对生物质而言,效果不很明显.     

0.6m3水力碎浆机传动系统的设计

在水力碎浆机的设计过程中,传动系统的设计非常关键,因传动系统的设计直接决定了整台机器的性能、效率。传动系统将转距由电动机通过带轮传动、主轴传送至转盘、刀片,转盘的回转形成浆流的循环和物料的摩擦,加之转盘及槽体上安装的刀片的碎解作用,从而把物料碎解成浆。0.6m3水力碎浆机是专为造纸实验室而设计,该产品传动系统采用转子传动装置 皮带传动 立式电动机的结构形式,主要包括主轴、大皮带轮、轴承、轴承座、受浆盘和转盘等部件。与传统水力碎浆机设计不同的是,0.6m3水力碎浆机槽体内不设计传动结构,动力消耗少,运行平稳。     

马蹄形过水断面正常水深计算的遗传算法

马蹄形过水断面是无压输水隧洞中常采用的断面形式之一 ,因其几何形状复杂 ,水力计算困难。目前常采用的方法有试算法、图解法和迭代法 ,这些方法由于计算量大且精度不易保证 ,不便于在生产实践中应用推广。将马蹄形过水断面正常水深计算转化为非线性优化问题 ,采用实数编码的遗传算法进行求解 ,实例计算表明该方法精度高、通用性强、操作简便 ,便于在生产实践中应用。     

La3+,Ce3+对厌氧颗粒污泥在不同VFA底物中的产甲烷促进效应

采用静态实验研究了分别添加O.05mg·L^-1La^3＋和Ce^3＋对不同来源和保存状况条件下不同VFA底物的厌氧颗粒污泥产甲烷的影响。结果表明，乙酸为底物时加入Ce^3＋，丙酸加入La^3＋或Ce^3＋，乳酸加入La^3＋时都大大加快了反应初期污泥的产甲烷速率，且对比产甲烷活性SMA也有3％-8％的提高；O.05mg·L^-1La^3＋或Ce^3＋的加入使污泥利用丙酸的速度加快，对于厌氧反应器的恢复运行有一定的实际意义。甲酸为底物时，La^3＋，Ce^3＋的加入对污泥产甲烷曲线形状没有影响，对SMA则分别降低了9.21％和3.37％；乙酸添加La^3＋在反应初期明显降低了产甲烷速率，但SMA并未降低。厌氧颗粒污泥经长时间低温存放后，原来对其SMA有提高作用的稀土浓度此时可能会作用不明显甚至会降低SMA；低浓度稀土离子对污泥产甲烷活性产生抑制作用时，相同质量浓度下Ce^3＋比La^3＋对污泥的抑制作用小；驯化培养过程有利于污泥对稀土的适应。