Anisotropy of wood vibrational properties: dependence on grain angle and review of literature data

The anisotropy of vibrational properties influences the acoustic behaviour of wooden pieces and their dependence on grain angle (GA). As most pieces of wood include some GA, either for technological reasons or due to grain deviations inside trunks, predicting its repercussions would be useful. This paper aims at evaluating the variability in the anisotropy of wood vibrational properties and analysing resulting trends as a function of orientation. GA dependence is described by a model based on transformation formulas applied to complex compliances, and literature data on anisotropic vibrational properties are reviewed. Ranges of variability, as well as representative sets of viscoelastic anisotropic parameters, are defined for mean hardwoods and softwoods and for contrasted wood types. GA-dependence calculations are in close agreement with published experimental results and allow comparing the sensitivity of different woods to GA. Calculated trends in damping coefficient (tanδ) and in specific modulus of elasticity (E′/ρ) allow reconstructing the general tanδ-E′/ρ statistical relationships previously reported. Trends for woods with different mechanical parameters merge into a single curve if anisotropic ratios (both elastic and of damping) are correlated between them, and with axial properties, as is indicated by the collected data. On the other hand, varying damping coefficient independently results in parallel curves, which coincide with observations on chemically modified woods, either “artificially”, or by natural extractives.     

The effects of temperature and humidity on phenol-formaldehyde resin bonding

Summary The effects of temperature and relative humidity on phenol-formaldehyde resin bonding were evaluated. Two flakes in a lap-shear configuration were bonded under an environment of controlled temperature (110 °C, 120 °C, 130 °C, 140 °C) and relative humidity (41%, 75%, 90%) for a series of time periods (0.25 to 16 min). The lap-shear specimens were then shear-tested on a mechanical testing machine and the results were used to establish a family of bond strength development curves at each temperature and level of relative humidity. At 110°C, the higher relative humidity appeared to retard resin bonding. The effects of relative humidity diminished as temperature increased to 140 °C. Bond strength development was chemical ratecontrolled. The rate of bond strength development at each relative humidity follows a first order reaction mechanism. The activation energy of resin-wood bonding, determined by bonding kinetics, was higher than that of resin alone, determined by differential scanning calorimetry. This comparison indicates that to form a strong resin-wood bond, a higher energy level might be required.This material is based on work supported by the Ministry of International Affairs, Quebec Government, the Natural Sciences and Engineering Research Council of Canada, and Laval University (Quebec City). The work was also supported by the U.S. Department of Agriculture under research joint venture agreement FP-92-1835     

Chemical modification and wetting of medium density fibreboard panels produced from fibres treated with maleated polypropylene wax

Medium density fibreboard (MDF) was produced from fibres treated with maleated polypropylene wax. The objectives of this study were to investigate the effect of fibre treatment with maleated polypropylene wax on the advancing and receding contact angle and wicking of MDF panels by the Wilhelmy plate method; to verify the chemical reactions occurring between fibres and maleated polypropylene wax by infrared spectroscopy, and to verify if there are relationships with the water absorption of panels. Three maleated polypropylene wax contents (0, 3, 5%) and two resin types (urea–formaldehyde, UF and melamine–urea–formaldehyde, MUF) were considered in this study. Our results showed that the treatment increased the advancing contact angle of panels bonded with UF resin. The receding contact angles of MDF panels produced from treated fibres with 5% maleated polypropylene wax content were also increased by the treatment. Also, the wicking was reduced by the treatment independent of the maleated polypropylene wax content. Reductions of the wicking were 59% for panels bonded with UF resin and 73% for panels bonded with MUF. Relationships between the wicking and water absorption were observed. Chemical analysis realized by infrared spectroscopy did not detect the presence of an esterification reaction between wood fibres and anhydride groups of the maleated polypropylene wax. This suggests, therefore, that an esterification reaction did not take place or that chemical modifications were so small that they are not visible by infrared spectroscopy.     

Improved water repellency of black spruce wood surfaces after treatment in carbon tetrafluoride plasmas

Plasma treatments for black spruce wood (Picea mariana (Mill.) B.S.P.), a widespread forest species from Canada, were carried out in order to waterproof the exposed surfaces. Experiments were performed using inductively coupled argon plasma with carbon tetrafluoride as the gaseous precursor for plasma-enhanced chemical vapor deposition of functional fluoropolymer coatings on wood. Analysis of the wettability through water contact angle measurements showed water-repellent characteristics, with static contact angles up to 130° depending on plasma exposure time, CF₄ concentration in the Ar/CF₄ plasma, and plasma source-to-substrate distance. X-ray photoelectron spectroscopy investigations of plasma-treated wood surfaces confirmed the growth of a thin, fluorocarbon layer with fluorine atomic concentrations close to 50 % on highly hydrophobic wood surfaces. Estimation of the thickness of the coatings by stylus profilometry revealed that a minimum layer thickness of about 80 nm is required to obtain water repellant wood surfaces with minimum water uptake. This complete set of data indicates that fluorocarbon-containing plasmas represent a very promising approach for improving the durability of wood products in wet and humid conditions.     

Biodiversity of Arbuscular Mycorrhizal (AM) fungi in mangroves of Goa in West India

Seventeen mangrove species of eight families at seven riverine and fringe habitats in Goa West India were surveyed for Arbuscular Mycorrhizal (AM) fungal diversity. Sixteen species were found to be mycorrhizal and one species showed no AM fungal colonization. AM root colonization was recorded at all seven sites and ranged from 6%-77%. Maximum root colonization was recorded in Excoecaria agallocha (77%) and minimum colonization in Avicennia marina (6%). Paris-type colonization was predominant at all sites. Auxiliary cells were recorded in roots of Acanthus ilicifolius, Ceriops tagal and Sonneretia alba. AM fungal root colonization and spore density varied by plant species and site. Site average spore density ranged from 1.84 spores·g-1 to 0.54 spores·g-1 of soil. In total, 28 AM fungal species of five genera, viz. Glomus, Acaulospora, Scutellospora, Gigaspora and Entrophospora, were recovered. Glomus was the dominant genus, three species of which were sporocarpic forms. Maximum site species richness (SR) ranged from 16 to 5. Species richness was maximum in A. ilicifolius where seven species of three genera were recovered. Based on relative abundance (RA) and isolation frequency (IF), two common species, viz. G. intraradices and A. laevis, were recovered from all seven sites.     

Phenol-formaldehyde resin curing and bonding under dynamic conditions

Summary To better understand the curing and bonding behavior of phenol-formaldehyde (PF) resin under dynamic conditions, flakeboards were manufactured either by conventional pressing at 7% or 12% mat moisture content or by steam injection pressing with 10 or 20 seconds steaming duration. Resin-impregnated glass-cloth samples and lap-shear tension specimens were embedded in the core of each flakeboard. After the flakeboards were pressed for various periods of times, the samples and specimens were quickly retrieved. The degree of resin cure was determined on the resin-impregnated glass-cloth samples by dynamic mechanical analysis. The bond strengths were measured from the lap-shear tension specimens on a mechanical testing machine. The results of resin curing and bonding were then correlated to the performance of the resin-bonded boards, which were evaluated by internal bond, modulus of rupture, modulus of elasticity, and thickness swelling. Resin curing and lap-shear bonding did not proceed simultaneously. In conventional pressing, the mat moisture content (MC) at 12% favored resin curing, but slightly retarded lap-shear bonding, as compared to 7%MC. In steam injection pressing, the rates of resin curing and lap-shear bond strength development were much faster for 20 seconds than for 10 seconds of steaming duration. Longer press times were needed to obtain boards with maximum strength in the 12%MC conventional pressing and the 20-s steam duration steam injection pressing than in those conditions where moisture content was lower or steam time was less. The need for longer press times must be attributed to higher internal vapor pressures and/or lower wood and resin component strengths, rather than to incomplete cure or bonding.This material is based on work supported by the Ministry of International Affairs, Quebec Government, the Natural Sciences and Engineering Research Council of Canada, and Laval University (Quebec City). The work was also supported by the U.S. Department of Agriculture under research joint venture agreement FP-92-1835     

Comparison of physical and mechanical properties of tension and opposite wood from ten tropical rainforest trees from different species

On 10 trees from 10 species of French Guyana tropical rainforest in a clear active process of restoring verticality growth strains were measured in situ in order to determine the occurrence of tension wood within samples. Wood specimens were cut in the vicinity of the growth strains measurements in order to measure some mechanical and physical properties. As suspected, tensile growth strains was very much higher in tension wood zone, because longitudinal modulus of elasticity was slightly higher. Longitudinal shrinkage was also much higher in tension wood than in opposite wood.     

A statistical analysis of spatiotemporal variations and determinant factors of forest carbon storage under China’s Natural Forest Protection Program

The Natural Forest Protection Program (NFPP) is one of the key ecological forestry programs in China. It not only facilitates the improvement of forest ecological quality in NFPP areas, but also plays a significant role in increasing the carbon storage of forest ecosystems. The program covers 17 provinces, autonomous regions, and municipalities with correspondingly diverse forest resources and environments, ecological features, engineering measures and forest management regimes, all of which affect regional carbon storage. In this study, volume of timber harvest, tending area, pest-infested forest, fire-damaged forest, reforestation, and average annual precipitation, and temperature were evaluated as factors that influence carbon storage. We developed a vector autoregression model for these seven indicators and we studied the dominant factors of carbon storage in the areas covered by NFPP. Timber harvest was the dominant factor influencing carbon storage in the Yellow and Yangtze River basins. Reforestation contributed most to carbon storage in the state-owned forest region in Xinjiang. In state-owned forest regions of Heilongjiang and Jilin Provinces, the dominant factors were forest fires and forest cultivation, respectively. For the enhancement of carbon sequestration capacity, a longer rotation period and a smaller timber harvest are recommended for the Yellow and Yangtze River basins. Trees should be planted in state-owned forests in Xinjiang. Forest fires should be prevented in state-owned forests in Heilongjiang, and greater forest tending efforts should be made in the state-owned forests in Jilin.     

Post-emergent herbicidal activity of cineole derivatives

Essential oils are being investigated as potential herbicides or to provide leads to new environmentally and socially acceptable herbicides. Novel hydroxy and ester derivatives of 1,8-cineole and 1,4-cineole were synthesised, by chemical and biological methods, and have shown pre-emergence herbicidal activity against annual ryegrass and radish. Effects on post-emergence activity of these derivatives, as well as 1,8-cineole, eucalyptus oil and the carboxylic acids from which the esters were derived, against annual ryegrass and radish, are reported here. Results suggest that reduced root and shoot growth observed in pre-emergence herbicidal bioassays were due to post-emergence activity rather than delayed germination. All tested substances had a dose-dependent, post-emergence herbicidal activity against annual ryegrass and radish with many derivatives showing improved activity relative to 1,8-cineole and high-cineole eucalyptus oil. However, results do not support the postulate that cineole esters would be more active than their respective carboxylic acid and the hydroxy cineole. Phytotoxicity of ester derivatives may be due to metabolic cleavage of the esters to the hydroxy cineole and carboxylic acid within the plant.