Automatic detection of washboarding in bandsaws

This paper presents an on-line method for detecting washboarding generated in bandsaws. It uses a parameter based on the shape of sawing force amplitude distributions. The curve of the probability density function of the parallel sawing force amplitude obeyed a normal distribution for the normal sawn surface, but it changed to an M-shaped distribution when washboarding appeared on the sawn surface of the workpiece. The curve of probability density function of the normal sawing force amplitude obeyed the normal distribution for any sawn surface investigated. The workpiece including a knot did not influence use of the parameter for detecting the appearance of washboarding.     

Chemical changes in steam-pressed kenaf core binderless particleboard

The effects of chemical changes in kenaf core binderless particleboards on the bonding performance and thickness swelling of boards were investigated by chemical and spectroscopic analyses. Mild steam-injection treatments (0.6–1.0MPa) caused significant degradation of hemicelluloses, lignin, and cellulose. Conventional hot pressing caused a lower degree of degradation of the chemical components. The hot-pressed kenaf core board without any binders showed poor bonding performance. Thus, it was found that partial degradation of the three major chemical components of the kenaf core by mild steam-injection treatment increased the bonding performance and dimensional stability of the binderless boards, and gave better quality binderless boards than those made by hot-pressing treatments.Part of this report was presented at the 4th International Wood Science Symposium, Serpong, Indonesia, September 2002; and at the 53rd Annual Meeting of The Japan Wood Research Society, Fukuoka, March 2003     

Assignment of the 1H and 13C NMR spectra of 2-aminobenzamide-labeled galacto- and arabinooligosaccharides

1,4-Linked β-d-galactooligosaccharides with a degree of polymerization (DP) between 1 and 7 and 1,5-linked α-l-arabinooligosaccharides with a DP between 1 and 8 were labeled at their reducing ends with 2-aminobenzamide (2AB) in the presence of sodium cyanoborohydride. The 2AB-labeled oligosaccharides were shown to be homogeneous using high-performance anion-exchange chromatography (HPAEC) and by electrospray ionization mass spectrometry (ESI-MS). The signals in the ¹H and ¹³C nuclear magnetic resonance (NMR) spectra of the 2AB-labeled oligosaccharides were then assigned using one- and two-dimensional NMR spectroscopy. These NMR data will be useful for the structural analysis of enzymatically synthesized galactan and arabinan side chains derived from rhamnogalacturonan I.     

Simple method for synthesizing phenolicβ-O-4 dilignols

A modified synthetic method for phenolic-O-4 lignin substructure model dimers was developed involving protection of the phenolic hydroxyl group of acetophenons with benzoyl chloride, bromination with 4-dimethylaminopyridiniumbromide perbromide, condensation with phenols in the presence of 18-crown-6-ether, condensation with paraformaldehyde, reduction with NaBH₄ and debenzoylation. This method results in shorter reaction times and increasing yields without the application of strict anhydrous and drastic conditions or chloric solvents. This alternative route could be applied to the-O-4 dilignol syntheses of four combinations of guaiacyl and syringyl derivatives.     

Design and pilot production of a “spiral-winder” for the manufacture of cylindrical laminated veneer lumber

A new spiral-winder was developed for continuous manufacturing of cylindrical laminated veneer lumber (LVL), and a suitable resin adhesive for this cylindrical LVL manufacturing system was investigated. This phase was followed by trial manufacturing and evaluation of cylindrical LVL with the optimum resin adhesive identified. The results are summarized as follows. (1) The shortest gelation time was recorded with a mixture of two commercial resorcinol based resins (DF-1000 and D-33) at a weight ratio of 2575. (2) Bath temperature had a remarkable effect on the gelation time of the adhesive mix. (3) High bonding strength was recorded by 2575 DF-1000/D-33 adhesive mix at a high press temperature despite a short pressing duration. Based on the results of items (1) to (3), 2575 DF-1000/ D-33 is recommended for use in the new spiral-winder. (4) The mechanical properties of cylindrical LVL could be improved by using 2575 DF-1000/D-33 with wider veneer width and longer pressing time. (5) The mechanical properties, especially the modulus of rupture, of the cylindrical LVL manufactured require further improvement for practical structural application.     

Estimating the production and mortality of fine roots in a Japanese cedar (Cryptomeria japonica D. Don) plantation using a minirhizotron technique

Fine roots are a key component of forested ecosystems, but available information is still limited. This study examined the production and mortality of fine roots less than 1 mm in diameter in a Japanese cedar (Cryptomeria japonica D. Don) plantation located on the Kanto Plain in central Japan. We used a minirhizotron technique in combination with soil coring, and collected data for 1 year (May 2002–May 2003). Fine root production and mortality were determined from changes in the lengths of individual fine roots on minirhizotron tubes. Both fine root production and mortality rates were greater in the upper soil than in lower soil levels. Both rates were seasonal, with higher values in summer than in winter; this trend was more pronounced in upper soil levels. These results suggest that environmental conditions, such as temperature or soil properties, affect the production and mortality rates of fine roots. Fine root production and mortality occurred simultaneously, and their rates were similar, which may have led to unclear seasonal changes in fine root standing crop estimates. Soil coring indicated that the fine root biomass of this stand was about 120 g m⁻², of which 40% was from Japanese cedar. The estimated rates of dry matter production and mortality of total fine roots, including understory plants, were both approximately 300 g m⁻² year⁻¹.     

Fire-resistant performance of a laminated veneer lumber joint with metal plate connectors protected with graphite phenolic sphere sheeting

Creep under fire of laminated veneer lumber (LVL) joined with metal connectors was studied. The fire-resistant performance of LVL butt joints connected with metal plates protected with graphite phenolic sphere (GPS) sheeting was discussed. The GPS sheeting was overlaid on the joint in different sizes and locations. The joint was exposed to a burner with a top flame temperature of 800°C and loaded with a load of 200 N to test for creep under fire. The results showed that the fire-resistant performance of the joint was markedly improved by the sheeting. The size and location of the GPS sheet significantly affected the time to rupture of the specimen, which was six times longer than that without GPS. Temperature measurements at the joint showed that the GPS sheeting distributed the heat along the surface and delayed failure. Thermographic images and analyses clarified the improvement in fire-resistant properties due to GPS.     

Fundamental studies on wood/cellulose-plastic composites: effects of composition and cellulose dimension on the properties of cellulose/PP composite

Although wood/cellulose-plastic composites (WPC) of low wood/cellulose content have been more accepted worldwide and are promoted as low-maintenance, high-durability building products, composites containing high wood/cellulose content are not yet developed on an industrial scale. In this study, flow properties, mechanical properties, and water absorption properties of the compounds of cellulose microfiber/polypropylene (PP) and maleic anhydride-grafted polypropylene (MAPP) were investigated to understand effects of the high cellulose content and the dimensions of the cellulose microfiber. The molding processes studied included compression, injection, and extrusion. It was found that fluidity is not only dependent on resin content but also on the dimension of the filler; fluidity of the compound declined with increased fiber length with the same resin content. Dispersion of the composite was monitored by charge-coupled device (CCD) microscope. Increasing the plastic content in the cellulose-plastic formulation improved the strength of mold in addition to the bond development between resin and filler, and the tangle of fibers. The processing mode affected the physicomechanical properties of the cellulosic plastic. Compression-molded samples exhibited the lowest modulus of rupture (MOR) and modulus of elasticity (MOE) and the highest water absorption, while samples that were injection-molded exhibited the highest MOR (70 MPa) and MOE (7 GPa) and low water absorption (2%).     

Locating and identifying sound knots and dead knots on sugi by the rule-based color vision system

Knowledge of the occurrence of sound and dead knots on the surface of sugi is important for the classification and application of the material. This study examined a color vision system for detecting sound and dead knots on sugi. The system can be conceptually divided into three components: a CCD-camera scanning system, an image-segmenting module, and a rule-based defect identifying module. The results showed that the potential defect regions could be located by Otsus threshold algorithm in conjunction with t-test analysis. The accuracies of locating sound knots and dead knots were 92.6% and 97.1%, respectively. The rule-based approach was used to identify sound and dead knots and the identifying accuracies for sound knots and dead knots were 92.0% and 94.1%, respectively. The overall detection accuracy of the system was 87.6%. The results indicated that the rule-based color vision system is an efficient means of detecting sound knots and dead knots on sugi.     

The pharmacological effects of the anesthetic alfaxalone after intramuscular administration to dogs

The pharmacological effects of the anesthetic alfaxalone were evaluated after intramuscular (IM) administration to 6 healthy beagle dogs. The dogs received three IM doses each of alfaxalone at increasing dose rates of 5 mg/kg (IM5), 7.5 mg/kg (IM7.5) and 10 mg/kg (IM10) every other day. Anesthetic effect was subjectively evaluated by using an ordinal scoring system to determine the degree of neuro-depression and the quality of anesthetic induction and recovery from anesthesia. Cardiorespiratory variables were measured using noninvasive methods. Alfaxalone administered IM produced dose-dependent neuro-depression and lateral recumbency (i.e., 36 ± 28 min, 87 ± 26 min and 115 ± 29 min after the IM5, IM7.5 and IM10 treatments, respectively). The endotracheal tube was tolerated in all dogs for 46 ± 20 and 58 ± 21 min after the IM7.5 and IM10 treatments, respectively. It was not possible to place endotracheal tubes in 5 of the 6 dogs after the IM5 treatment. Most cardiorespiratory variables remained within clinically acceptable ranges, but hypoxemia was observed by pulse oximetry for 5 to 10 min in 2 dogs receiving the IM10 treatment. Dose-dependent decreases in rectal temperature, respiratory rate and arterial blood pressure also occurred. The quality of recovery was considered satisfactory in all dogs receiving each treatment; all the dog exhibited transient muscular tremors and staggering gait. In conclusion, IM alfaxalone produced a dose-dependent anesthetic effect with relatively mild cardiorespiratory depression in dogs. However, hypoxemia may occur at higher IM doses of alfaxalone.