Initial shapes of stress-strain curve of wood specimen subjected to repeated combined compression and vibration stresses and the piezoelectric behavior

This study investigated the relationship between the initial shape of the stress (σ)-strain (ε) curve of a Chamaecyparis obtusa wood specimen subjected to repeated combined compression and vibration stresses at various angles between the fiber direction and load direction and the piezoelectric behavior. The main findings of the study are: (1) the σ-ε curve became convex initially, and then the stress was proportional to the strain. The σ-ε curve had almost the same shape during both loading and unloading. (2) The σ-piezoelectric voltage (P) curve was nonlinear, with a maximal point or cusp on the curve, which had almost the same shape during both loading and unloading, as was also observed for the σ-ε curve. (3) The plot of the first derivative of the stress [dσ/dε (= σ′)] against ε was nonlinear. The σ′-ε and P-ε curves at various angles were fairly similar. (4) The stress at the maximal point (or cusp) of the σ-P curve decreased with an increase in the angle between the fiber direction and load direction. The tendency of the stresses was very similar to that of Young’s modulus and compression strength calculated from Hook’s law and Hankinson’s law, respectively.     

The influences of boiling and drying treatments on the behaviors of tension wood with gelatinous layers in <Emphasis Type="Italic">Zelkova serrata</Emphasis>

This study examined how boiling and drying treatments influenced various physical properties of the tension wood with gelatinous fibers (G-fibers) of a 29-yearold Zelkova branch. By boiling treatment, tension wood with numerous G-fibers contracted considerably in the longitudinal direction and the longitudinal Young’s modulus decreased in spite of the water-saturated condition. The drying treatment caused green tension wood and boiled tension wood with numerous G-fibers to shrink longitudinally and increased their longitudinal Young’s moduli. These specific behaviors in tension wood were highly correlated with the proportion of G-fibers in a specimen and were probably caused by the microscopic behavior of cellulose microfibril (CMF) in the gelatinous layers (G-layers). The longitudinal shrinkage of tension wood due to drying suggests the existence of a hygro-sensible, noncrystalline region in the CMF, which is abundant in the G-layer. Furthermore, the noncrystalline region in the CMF softens during boiling treatment, resulting in the reduction of the longitudinal Young’s modulus in tension wood. The longitudinal contraction of tension wood with G-fibers by boiling might be caused by the tensile growth stress remaining in green G-layers. However, no changes were detected in the 004 d-spacing of cellulose crystal in tension wood from the boiling and drying treatments, regardless of the proportion of G-fibers.     

Antifeedant activity of flavonoids and related compounds against the subterranean termiteCoptotermes formosanus Shiraki

Antifeedant activity of some flavonoids and their related compounds against the subterranean termiteCoptotermes formosanus Shiraki was examined with nochoice tests and two-choice tests. The activities of these compounds were evaluated in relation to their chemical structures. All flavonoids tested showed antifeedant activity, whereas catechinic acid, possessing no A-ring or pyran ring in the molecule, showed feeding-preference activity. For the structure-activity relations, it was found that compounds containing two hydroxyl groups at C-5 and C-7 in A-rings showed high antifeedant activity. Furthermore, the presence of a carbonyl group at C-4 in the pyran rings of the compounds was necessary for the occurrence of high activity. 3-Hydroxyflavones and 3-hydroxyflavanones with 3,4-dihydroxylated B-rings exhibited higher activity than those with 4-hydroxylated B-rings.Part of this paper was presented at the 49th annual meeting of the Japan Wood Research Society, Tokyo, April 1999     

Removal of trichloroethylene from aqueous solution by pyrolyzed Japanese cedar bark

The bark of Japanese cedar (Cryptomeria japonica D. Don) was heated in an N₂ atmosphere at 300–900C for 3h to investigate the surface properties of the pyrolyzed residuces and their ability to remove trichloroethylene (TCE) from aqueous solutions. The specific surface areas (S _N) and total pore volumes (V _N) of the pyrolyzed barks steadily increased with rising pyrolysis temperature; no significant differences in the average pore diameters (D _N) were observed at higher temperatures (600–900C). The adsorption capacities of the pyrolyzed residues for TCE were determined under batch mode conditions using an aqueous solution containing 500g TCE dm^–3. The adsorption data were well fitted to the Freundlich equation. The adsorption capacity of the bark pyrolyzed at 900C was about five times larger than that of commercial activated carbon.This study was presented at the 10th International Symposium on Wood and Pulping Chemistry, Yokohama, June 1999     

Dielectric relaxation due to heterogeneous structure in moist wood

Dielectric properties in three main directions for hinoki wood (Chamaecyparis obtusa) specimens conditioned at various levels of relative humidity were measured in the frequency range from 20 Hz to 10 MHz over the temperature range from −150°C to 20°C. Three relaxations were observed in the specimens conditioned at high levels of relative humidity. The relaxation in the highest frequency range was ascribed to the motions of adsorbed water molecules. The relaxation in the middle frequency range remained unchanged by the ethanol–benzene extraction of specimens. The relaxation location was independent of measuring directions. The relaxation in the lowest frequency range was not detected in the specimens impregnated with methyl methacrylate (MMA). This result suggested that the relaxation was due to electrode polarization. The Cole-Cole circular arc law applied well to two relaxations recognized in the specimens impregnated with MMA. The relaxation magnitude in the middle frequency range was extremely large, and the distribution of relaxation times was very narrow. These characteristics suggested relaxation of the Maxwell-Wagner type resulting from the interfacial polarization in the heterogeneous structure, which included adsorbed water with large electrical conductivity within the insulating cell walls.     

Mechanical behavior of the crystal lattice of natural cellulose in wood under repeated uniaxial tension stress in the fiber direction

This study investigated the relationship between the cellulose crystal lattice strain (crystalline region) and the macroscopic surface strain in specimens of Chamaecyparis obtusa wood under repeated uniaxial tension stress in the fiber direction. Changes in the strain of the crystal lattice were measured from the peak of (004) reflection using the transit X-ray method. The macroscopic surface strain of each specimen was measured with a strain gauge. In both loading and unloading, the surface strain changed linearly with changes in stress. However, crystal lattice strain was not linear but exhibited changes along a curve with changing stress. Under stressed conditions, the crystal lattice strain was always less than the surface strain, regardless of the frequency of repetition in the loading and unloading cycle. The ratio of the crystal lattice strain to the surface strain showed a negative correlation for stress in both loading and unloading. That is, the ratio decreased with increasing stress, and finally tend to converge to a specific value. The ratio (I/I ₀) between the diffracted intensity (I ₀) in the (004) plane in the unloaded condition and the diffracted intensity (I) in the (004) plane in the loaded condition tend to converge on a specific value with increasing frequency of repetition. When the substantial tension Young’s modulus of the wood in the longitudinal direction decreased, the ratio of the strain of the crystal lattice to the surface strain also decreased. Moreover, the ratio decreased with increasing microfibril angle of the specimen.     

Effects of light and microsite conditions on tree size of 6-year-old Cryptomeria japonica planted in a group selection opening

We examined the extent to which direct and indirect measures of light and microsite conditions could explain variation in tree height and diameter at the base of 6-year-old Cryptomeria japonica trees planted in a group selection opening of about 0.32 ha on a steep slope at Shiiba, Miyazaki Prefecture, southern Japan. We first used the gap light index (GLI) and soil thickness (ST) as directly measured indices. For an indirect measure of light, we used a between-cohort competition index (BCI) estimated from the position and total height of residual trees. For indirect measures of microsite, we examined topographic indices (slope, plan and profile curvature, average slope gradient, and relative elevation) derived from digital elevation models (DEMs) with different resolutions ranging from 2 to 10 m. The multiple linear regression using GLI and ST explained about 45% of variation in tree size, while simple regression using only GLI explained about 35%. The contribution of ST was about half of GLI. The multiple regressions using BCI and the topographic indices did not explain any more variation than using BCI alone (R ² of about 0.26). We conclude that microsite conditions with shallower soil and steeper slope have negative effects on tree growth in group selection openings, although the relative importance is smaller than light conditions. More comprehensive studies considering several openings with more heterogeneous topography including different species are needed to generalize our growth prediction using the indirect measures, which are useful for practical forest management.     

Effects of high temperature kiln drying on the practical performances of Japanese cedar wood (Cryptomeria japonica) I: changes in hygroscopicity due to heating

The effect of heating on the hygroscopicity of Japanese cedar wood was investigated as a simple evaluation of thermal degradation in large-dimension timber being kiln-dried at high temperatures (>100°C). Small wood pieces were heated at 120°C in the absence of moisture (dry heating) and steamed at 60°, 90°, and 120°C with saturated water vapor over 2 weeks, and their equilibrium moisture contents (M) at 20°C and 60% relative humidity (RH) were compared with those of unheated samples. No significant change was induced by steaming at 60°C, while heating above 90°C caused loss in weight (WL) and reduction in M of wood. The effects of steaming were greater than those of dry heating at the same heating temperature. After extraction in water, the steamed wood showed additional WL and slight increase in M because of the loss of water-soluble decomposition residue. The M of heated wood decreased with increasing WL, and such a correlation became clearer after the extraction in water. On the basis of experimental correlation, the WL of local parts in large-dimension kiln-dried timber was evaluated from their M values. The results indicated that the thermal degradation of inner parts was greater than that of outer parts.     

Changes of decay and termite durabilities of Japanese larch (Larix leptolepis) wood due to high-temperature kiln drying processes

We investigated the effects of high-temperature drying schedules (120°–130°C) on decay and termite feeding of Japanese larch timbers. Thermogravimetric analysis was conducted to investigate changes of the wood components. Decay and termite feeding tests showed that specimens dried under high-temperature schedules were susceptible against a decaying fungus Fomitopsis palustris and attacks from termites Coptotermes formosanus and Reticulitermes speratus. These drying schedules changed chemical components, which were suggested by the thermal analytical result compared to the control sample. The results of this study indicated that the acceleration of termite feeding takes place even under temperatures that are comparatively lower than that used in our previous research in which 170°C steaming treatment was applied to Japanese larch wood. Decay durability against a brown rot fungus also decreased, possibly from production of low molecular weight fragments when hemicellulose decreased during the high-temperature drying processes.