Removal of trichloroethylene from aqueous solution by pyrolyzed Japanese cedar bark

The bark of Japanese cedar (Cryptomeria japonica D. Don) was heated in an N₂ atmosphere at 300–900C for 3h to investigate the surface properties of the pyrolyzed residuces and their ability to remove trichloroethylene (TCE) from aqueous solutions. The specific surface areas (S _N) and total pore volumes (V _N) of the pyrolyzed barks steadily increased with rising pyrolysis temperature; no significant differences in the average pore diameters (D _N) were observed at higher temperatures (600–900C). The adsorption capacities of the pyrolyzed residues for TCE were determined under batch mode conditions using an aqueous solution containing 500g TCE dm^–3. The adsorption data were well fitted to the Freundlich equation. The adsorption capacity of the bark pyrolyzed at 900C was about five times larger than that of commercial activated carbon.This study was presented at the 10th International Symposium on Wood and Pulping Chemistry, Yokohama, June 1999     

Dielectric relaxation due to heterogeneous structure in moist wood

Dielectric properties in three main directions for hinoki wood (Chamaecyparis obtusa) specimens conditioned at various levels of relative humidity were measured in the frequency range from 20 Hz to 10 MHz over the temperature range from −150°C to 20°C. Three relaxations were observed in the specimens conditioned at high levels of relative humidity. The relaxation in the highest frequency range was ascribed to the motions of adsorbed water molecules. The relaxation in the middle frequency range remained unchanged by the ethanol–benzene extraction of specimens. The relaxation location was independent of measuring directions. The relaxation in the lowest frequency range was not detected in the specimens impregnated with methyl methacrylate (MMA). This result suggested that the relaxation was due to electrode polarization. The Cole-Cole circular arc law applied well to two relaxations recognized in the specimens impregnated with MMA. The relaxation magnitude in the middle frequency range was extremely large, and the distribution of relaxation times was very narrow. These characteristics suggested relaxation of the Maxwell-Wagner type resulting from the interfacial polarization in the heterogeneous structure, which included adsorbed water with large electrical conductivity within the insulating cell walls.     

Mechanical behavior of the crystal lattice of natural cellulose in wood under repeated uniaxial tension stress in the fiber direction

This study investigated the relationship between the cellulose crystal lattice strain (crystalline region) and the macroscopic surface strain in specimens of Chamaecyparis obtusa wood under repeated uniaxial tension stress in the fiber direction. Changes in the strain of the crystal lattice were measured from the peak of (004) reflection using the transit X-ray method. The macroscopic surface strain of each specimen was measured with a strain gauge. In both loading and unloading, the surface strain changed linearly with changes in stress. However, crystal lattice strain was not linear but exhibited changes along a curve with changing stress. Under stressed conditions, the crystal lattice strain was always less than the surface strain, regardless of the frequency of repetition in the loading and unloading cycle. The ratio of the crystal lattice strain to the surface strain showed a negative correlation for stress in both loading and unloading. That is, the ratio decreased with increasing stress, and finally tend to converge to a specific value. The ratio (I/I ₀) between the diffracted intensity (I ₀) in the (004) plane in the unloaded condition and the diffracted intensity (I) in the (004) plane in the loaded condition tend to converge on a specific value with increasing frequency of repetition. When the substantial tension Young’s modulus of the wood in the longitudinal direction decreased, the ratio of the strain of the crystal lattice to the surface strain also decreased. Moreover, the ratio decreased with increasing microfibril angle of the specimen.     

Effects of light and microsite conditions on tree size of 6-year-old Cryptomeria japonica planted in a group selection opening

We examined the extent to which direct and indirect measures of light and microsite conditions could explain variation in tree height and diameter at the base of 6-year-old Cryptomeria japonica trees planted in a group selection opening of about 0.32 ha on a steep slope at Shiiba, Miyazaki Prefecture, southern Japan. We first used the gap light index (GLI) and soil thickness (ST) as directly measured indices. For an indirect measure of light, we used a between-cohort competition index (BCI) estimated from the position and total height of residual trees. For indirect measures of microsite, we examined topographic indices (slope, plan and profile curvature, average slope gradient, and relative elevation) derived from digital elevation models (DEMs) with different resolutions ranging from 2 to 10 m. The multiple linear regression using GLI and ST explained about 45% of variation in tree size, while simple regression using only GLI explained about 35%. The contribution of ST was about half of GLI. The multiple regressions using BCI and the topographic indices did not explain any more variation than using BCI alone (R ² of about 0.26). We conclude that microsite conditions with shallower soil and steeper slope have negative effects on tree growth in group selection openings, although the relative importance is smaller than light conditions. More comprehensive studies considering several openings with more heterogeneous topography including different species are needed to generalize our growth prediction using the indirect measures, which are useful for practical forest management.     

Effects of high temperature kiln drying on the practical performances of Japanese cedar wood (Cryptomeria japonica) I: changes in hygroscopicity due to heating

The effect of heating on the hygroscopicity of Japanese cedar wood was investigated as a simple evaluation of thermal degradation in large-dimension timber being kiln-dried at high temperatures (>100°C). Small wood pieces were heated at 120°C in the absence of moisture (dry heating) and steamed at 60°, 90°, and 120°C with saturated water vapor over 2 weeks, and their equilibrium moisture contents (M) at 20°C and 60% relative humidity (RH) were compared with those of unheated samples. No significant change was induced by steaming at 60°C, while heating above 90°C caused loss in weight (WL) and reduction in M of wood. The effects of steaming were greater than those of dry heating at the same heating temperature. After extraction in water, the steamed wood showed additional WL and slight increase in M because of the loss of water-soluble decomposition residue. The M of heated wood decreased with increasing WL, and such a correlation became clearer after the extraction in water. On the basis of experimental correlation, the WL of local parts in large-dimension kiln-dried timber was evaluated from their M values. The results indicated that the thermal degradation of inner parts was greater than that of outer parts.     

Changes of decay and termite durabilities of Japanese larch (Larix leptolepis) wood due to high-temperature kiln drying processes

We investigated the effects of high-temperature drying schedules (120°–130°C) on decay and termite feeding of Japanese larch timbers. Thermogravimetric analysis was conducted to investigate changes of the wood components. Decay and termite feeding tests showed that specimens dried under high-temperature schedules were susceptible against a decaying fungus Fomitopsis palustris and attacks from termites Coptotermes formosanus and Reticulitermes speratus. These drying schedules changed chemical components, which were suggested by the thermal analytical result compared to the control sample. The results of this study indicated that the acceleration of termite feeding takes place even under temperatures that are comparatively lower than that used in our previous research in which 170°C steaming treatment was applied to Japanese larch wood. Decay durability against a brown rot fungus also decreased, possibly from production of low molecular weight fragments when hemicellulose decreased during the high-temperature drying processes.     

Compressive deformation of wood impregnated with low molecular weight phenol formaldehyde (PF) resin II: effects of processing parameters

To obtain high-strength phenol formaldehyde (PF) resin-impregnated compressed wood at low pressing pressure, the effects of resin content, preheating temperature, pressing temperature, and pressing speed on the compressive deformation of oven-dried low molecular weight PF resin-impregnated wood was investigated. With an increase of PF resin content, the Youngs modulus of the cell wall perpendicular to the fiber direction decreases, and collapse-initiating pressure decreases linearly with the Youngs modulus. This indicates that the occurrence of cell wall collapse is strain-dependent. By increasing preheating temperatures, the collapse-initiating pressure increases due to the increment of the Youngs modulus of the cell wall. An increase in pressing temperature results in the thermal softening of the cell wall and causes collapse at a lower pressure. The wood is compressed effectively despite accelerated resin curing. The pressing speed significantly affects the viscoelastic deformation of the cell wall and the wood is well deformed with decreasing pressing speed, although the differences in density and mechanical properties are relatively small after a pressure-holding period of 30min. In all the parameters examined in this study, the Youngs modulus and bending strength increase with increasing density.     

Condensation reactions of phenolic resins V: cure-acceleration effects of propylene carbonate

Propylene carbonate (PC) is known as one of the cure accelerators for alkaline phenol–formaldehyde resins. To elucidate the cure-acceleration mechanisms, the effects of PC on the condensation reactions of monomeric hydroxymethylphenols (HMPs) were investigated and compared with those of PC hydrolysate, sodium bicarbonate (NaHCO₃) and ethyl formate. Immediately after the reaction started, PC, decomposing itself simultaneously, accelerated the formation of the ortho-para methylene-bonded dimer of 2,4,6-trihydroxymethylphenol. This effect of PC was very similar to that of ethyl formate. To the contrary, PC hydrolysate accelerated the formation of the para-para methylene-bonded dimer throughout the course of the reaction. This effect of PC hydrolysate was identical to that of NaHCO₃. These results indicate that PC increases the reactivity of the ortho-hydroxymethyl group, presumably through transesterification. On the other hand, NaHCO₃ is formed by the hydrolysis of PC or decomposition of the transesterified HMPs and it increases the reactivity of the para-hydroxymethyl group.     

Pilot Study to Examine Radial Variation in Annual Ring Width, Density and Shrinkage

The annual ring width, density and shrinkage variation from pith to bark in Chinese fir (Cunninghamia lanceolata) and Boka sugi (Cryptomeria japonicd) were studied and compared. The results show that the ring width decreased sharply from pith to bark for Chinese fir. However, the ring width variation pattern for Boka sugi followed a different way, i.e., the ring width decreased to the fifth ring, increased to the tenth ring, decreased again to the fifteenth, and then increased to the twentieth, where it became constant. The large variations of Boka sugi appeared to show the maintenance of fast growth for many years. The annual ring mean density of Chinese fir increased gradually from pith to bark. However, the density changes for Boka sugi indicated the opposite trend, i.e., the mean density decreased gradually from pith to bark. The former showed a pattern as the same as a pine and a larch, and the latter was often found in a cedar and a cypress. The longitudinal shrinkage in juvenile wood was much hig