基于响应面法的板料成形工作模面几何参数优化

阐述了以响应面法建立板料成形参数与有限元模拟结果的代理模型的基本原理;介绍了板料成形中的设计变量、目标函数、约束条件,多目标优化的处理方法;基于响应面法.以汽车后桥悬架内板零件为研究对象,成形后最小板料厚度为优化目标,成形极限图为约束条件,建立了模面几何参数优化模型;对模面几何参数进行优化并获得最优参数组合;以最优几何参数组合进行了实际的冲压试验,验证了优化结果.     

驱动圆盘犁的研究与设计

驱动圆盘犁对土堡侧面和底部的土壤进行旋转滑切,将土垡底部的土壤由沟底撕裂开形成土垡,并利用圆盘的旋转将土垡抬升并翻转.为此,以研究驱动圆盘犁为目标,分析了驱动圆盘犁各几何参数和工作参数对其工作过程的影响,为驱动圆盘犁的研制提供了可靠的理论依据.通过理论分析,阐明了驱动圆盘犁的运动学特性,推导了残耕高度的计算公式.     

封闭式蛋鸡舍环境控制系统的设计

针对全封闭的蛋鸡舍结构特点和室内环境因子不同于外界环境等问题,设计开发了全封闭蛋鸡舍环境调控系统.该系统以单片机LPC2132为微控器,由上位机和智能监控点构成监控硬件系统,其执行机构由湿帘风机、喷雾等设施组成.该系统根据智能监控点传来的传感器所采集信息数据,通过一定算法分析决策,能够实现鸡舍内的温度、湿度、光照度、二氧化碳、氨气和硫化氢按照设定值自动调控.夏季试验结果表明:在封闭式蛋鸡舍试用的环境调控系统,对蛋鸡舍环境因子中的温度和湿度进行了调控试验,试验期间的蛋鸡的产蛋率比对照组高出约15%,说明设计的蛋鸡舍环境控制系统具有推广价值.     

Transpositional feeding rhythm of loach <Emphasis Type="Italic">Misgurnus anguillicaudatus</Emphasis> from larvae to juveniles and its ontogenesis under artificial rearing conditions

The diel feeding rhythm and ontogenesis during early life stage of loach Misgurnus anguillicaudatus were investigated under experimental conditions (light: L 06:00–18:00, D 18:00–06:00 h). Morphological and behavioral developments of loach from newly hatched to 40 days after hatching were observed. Larvae were able to prey on daphnia 3–4 days after hatching at 23 ± 0.5°C. As the larvae grew, they showed an increasing feeding capacity and a distinct feeding rhythm. Feeding intensity and incidence for day-4 larvae were highest at 10:00 and 16:00 h. The highest levels of feeding intensity for day-12 larvae occurred at 08:00, 12:00, and 18:00 h as did feeding incidence. By day 20, when the larvae metamorphosed, the highest levels of feeding intensity occurred at 06:00, 18:00, and 24:00 h and were concurrent with the highest feeding incidence. After metamorphosis, feeding capacity had again increased considerably and, in contrast to the earlier stages before day 20, feeding intensity for day-30 juveniles peaked at 05:00 and 20:00 h, about 1–2 h after the maximum feeding incidence. The feeding rhythm of loach juveniles at day 40 was almost the same as the day-30 juveniles. The estimated maximum daily feeding rates were 43.1%, 33.4%, 19.0%, 12.8%, and 5.8% of body weight on days 4, 12, 20, 30, and 40, respectively. Thus, loach was found to have different feeding rhythms in the pre- and post-metamorphosis stages, with the highest feeding activity in daytime during the larval planktonic stage before metamorphosis, and intensely nocturnal feeding behavior during the juvenile benthic stage after metamorphosis.     

海水育苗锅炉的节能降耗

海水养殖业中耗能较大的环节是海水育苗,因为育苗企业鼓风机天天转、锅炉天天烧、水泵天天抽,既是耗煤大户又是耗电大户,所以海水育苗行业如何在保证正常生产的前提下把能耗降下来是今后育苗生产中的一个重要工作。在此,笔者就本行业锅炉的一些使用方法略做说明。     

Preparation of PHEMA/nHAP nanocomposites via <Emphasis Type="Italic">in situ</Emphasis> polymerization in supercritical carbon dioxide for biomedical applications

Poly(2-hydroxyethylmethacrylate) (PHEMA)/hydroxyapatite (HAP) nanocomposites were synthesized through a new route involving nano-sized HAP (nHAP) particles or modified nHAP mixed with monomer 2-hydroxyethylmethacrylate via in situ polymerization in supercritical carbon dioxide (scCO₂). Fourier-transform infrared spectroscopy showed phosphate peak increased with nHAP content in composite. X-ray diffraction patterns of PHEMA/nHAP revealed the presence of crystallized nHAP. Thermogravimetric analysis showed that the ultimate nHAP content in PHEMA/nHAP composites is consistent with its initial amount. Scanning electron microscopy revealed that nanocomposite particles are much smaller than PHEMA particles. PHEMA/nHAP composites with average diameter of approximately 600 nm were obtained in scCO₂ with 94 % yield. Mechanical properties of PHEMA/nHAP nanocomposites were better than those of PHEMA, and compressive modulus and strength of composites with 30 wt.% nHAP were 193 and 29 MPa, respectively. Nanocomposite adsorption toward bovine serum albumin was evaluated, and results indicated that analyte adsorption amount can reach up to 282 mg/g.     

Conferring resistance to pre-harvest sprouting in durum wheat by a QTL identified in <Emphasis Type="Italic">Triticum spelta</Emphasis>

Pre-harvest sprouting (PHS) causes significant yield loss and degrade the end-use quality of wheat, especially in regions with prolonged wet weather during the harvesting season. Unfortunately, the gene pool of Triticum durum (tetraploid durum wheat) has narrow genetic base for PHS resistance. Therefore, finding out new genetic resources from other wheat species to develop PHS resistance in durum wheat is of importance. A major PHS resistance QTL, Qphs.sicau-3B.1, was mapped on chromosome 3BL in a recombinant inbred line population derived from ‘CSCR6’ (Triticum spelta), a PHS resistant hexaploid wheat and ‘Lang’, a PHS susceptible Australian hexaploid wheat cultivar. This QTL, Qphs.sicau-3B.1, is positioned between DArT marker wPt-3107 and wPt-6785. Two SCAR markers (Ph3B.1 and Ph3B.2) were developed to track this major QTL and were used to assay a BC₂F₈ tetraploid population derived from a cross between the durum wheat ‘Bellaroi’ (PHS susceptible) and ‘CSCR6’ (PHS resistant). Phenotypic assay and marker-assisted selection revealed five stable tetraploid lines were highly PHS resistant. This study has successfully established that PHS-resistance QTL from hexaploid wheat could be efficiently introgressed into tetraploid durum wheat. This tetraploid wheat germplasm could be useful in developing PHS resistant durum cultivars with higher yield and good end-use quality.     

高强钢焊接薄腹工形截面双向压弯构件的稳定性

应用ANSYS有限元,分析了Q460高强钢焊接薄腹工形截面双向压弯构件的稳定性能,提出了可供实际应用参考的设计公式。分析中考虑的主要参数有腹板高厚比,构件长细比,翼缘宽厚比及荷载偏心率。结果表明,对受压为主的构件,腹板局部屈曲对构件稳定承载力影响较大,而对受弯为主的构件,这一因素对构件稳定承载力影响较小。有限元分析结果与现行规范方法计算结果比较表明,目前规范方法尚不能较好地计算高强钢焊接薄腹工形截面双向压弯构件的稳定承载力,因而提出了修正直接强度法,该法精度较好且偏于安全。     

钾硅钙微孔矿物肥对水稻重金属镉的降阻效果研究

为了探明钾硅钙微孔矿物肥对污染稻田土壤重金属镉(Cd)有效性的影响,弄清其对稻谷中Cd含量的降低效果。采用田间小区试验和室内分析测定方法进行研究,试验设5个处理,处理1:对照(CK),常规施肥(40%复合肥450 kg/hm2);处理2:钾硅钙微孔矿物肥600 kg/hm2+常规施肥;处理3:钾硅钙微孔矿物肥750 kg/hm2+常规施肥;处理4:钾硅钙微孔矿物肥1125 kg/hm2+常规施肥;处理5:钾硅钙微孔矿物肥1425 kg/hm2+常规施肥。结果表明:钾硅钙微孔矿物肥可以显著提高水稻穗总粒数、穗实粒数和结实率,提高水稻产量,增产率达到7.5%~16.0%;增加土壤碱解氮、有效磷和速效钾含量,提高土壤pH值,降低土壤有效Cd含量,从而降低稻谷Cd的积累,最大降低稻谷Cd含量达到38.6%。钾硅钙微孔矿物肥要达到降阻水稻重金属Cd的最佳效果,施用量不能低于1425 kg/hm2。     

2018年我国农药进出口特点与2019年趋势分析

Li Lin;Jin Hejiang;Huang Xinhe;Cao Bingwei;Wu Lihui;Liu Pingping;Qu Mengmeng;Wu Houbin(The Institute for the Control of Agrochemicals,Ministry of Agriculture and Rural Affairs,Beijing 100125,China)