卷柏启动培养研究

以卷柏（Selaginella tamariscina）幼叶、茎尖及茎段为外植体,研究了不同消毒方式的消毒效果以及基本培养基类型和激素组合对初代培养的影响。结果表明：以卷柏的茎尖为外植体,用5 g.L-1多菌灵处理8 h的消毒方式,取得了较好的消毒效果,无菌率可达79.8%;茎尖最佳初代培养基为MS＋KT 2 mg.L-1＋NAA0.2 mg.L-1＋IAA 0.1 mg.L-1。     

东福米业有限责任公司在吉林省新农村建设中的启迪作用

吉林市东福米业在近几年的发展中引起了国内外学者的高度重视,本文通过对公司发展模式的分析,提炼出了对吉林省新农村的启迪作用。     

深州杨生物学特性及栽培管理

河北省深州市当地群众为了解决毛白杨(Populus tomentosa Carr)扦插成活率低这一实际难题,进行了毛白杨的芽接繁殖,从中发现了新的毛白杨杂合体,定名为深州杨.作者对深州杨的生物学特性、分化特性及栽培管理进行了初步介绍,为生产实践提供依据.     

浅析新形势下的土地流转问题

随着新形势的发展,在土地方面也出现了一些新问题,新情况,作者就本地的土地流转做法,推荐一下,以供参考。     

Heat Transfer Performance of Capillary Mats Using Wet Construction in Winter

For the capillary mats using wet construction, a winter experiment designed to investigate the heat transfer performance was described, and the heat transfer performance analysis which contains the comparisons between different pipe space and different thickness of cement mortar surface was carried out. As a result, compared with that of the traditional radiant heating pipes, the capillary mats of wet construction require supply water with lower temperature, and it shows good heat transfer performance and system energy efficiency as well. According to the demand of indoor heat dissipation and human comfort as well as the coupling relationship between the temperature of supply water and surface construction thickness, it is suggested that the proper construction method should be comprehensively considered in practical applications.     

Numerical analysis on fan shaped air blast atomizer parameters

Based on Eulerian Lagrangian coupling algorithm, the performance parameters of Fan shaped air blast atomizer is simulated. It is shown that when gas liquid mass flow ratio is constant, the spray angle and velocity of droplet decreases and SMD increases gradually with the increase of orifice width. Therefore, in order to obtain much smaller liquid droplet, orifice width should not be too wide. When the orifice width is constant, along with the increase of gas liquid mass flow ratio, SMD decreases firstly and increases later when reaching the minimum. And SMD minimum value is 39.5 μm when the orifice width is 0.6 mm.     

Heuristic research and fuzzy evaluation for-post-faultrestoration in distribution networks

A heuristic research and fuzzy evaluation fault restoration algorithm for distribution network is proposed to quickly restore power supply for the regions where power supply is interrupted. The algorithm searches power supply paths by finding effective tie-switches and sectionalizing switches, and eliminates improper switch pair according to power flow calculation. During service restoration process, the problem is divided into self-healing restoration, whole-region restoration, sub-region restoration, load-transfer restoration and load shedding restoration. The algorithm takes switch operation times and customer priority into account, and consequently, obtains initial feasible schemes. Fuzzy technique is used to evaluate the schemes from minimal switch operation times, load transfer, feeder margin and maximal voltage drop. Weighted sum of four indices provides a good guideline for choosing the optimal scheme for restoration operation. Calculation results of a certain distribution network show that this algorithm is feasible.     

Numerical simulation and optimization of high strength steel bumper forming process and springback control

Production of high strength steel bumper can greatly enhance the occupant safety.However,it is very hard to form high strength steel plate.There is rare domestic successful reference.The hot stamping technology aboard increases costs significantly,and the efficiency is low.Therefore,the only solution is combining advanced numerical simulation technology with current adjusting stamping process.The cold forming process of a sedan’s high strength steel bumper is simulated by FEM software Dynaform and the results show that springback and crack are the main defects.A law is summed up by researching the influence of different shapes of addendums on part forming and springback.Finally,the optimized shape of addendum is obtained by adjusting the addendum and adding convex roofs.It provides references for manufacturing similar high strength steel parts.     

Damage Identification for Guyed Mast Based on WVD Cross term Statistic Distinction

The relative alteration of Wigner Ville Distribution cross term statistic was proposed for damage detection of guyed masts. And numerical analysis and experimental study were carried out with the case of the aero navigating guyed mast in Fuling District. It was found that not only the shaft’s damage of different location and degree, but also the local damage of different type could be identified with the relative alteration of WCS accurately. The accuracy and sensitivity of the identification can be improved by increasing the guy’s initial pre tensions. The damage identification test can quantify the damage extent of simulation. And it was indicated that the WCS index can identify the local damage of guyed mast and the results of damage identification were in good agreement with those of numerical analysis.     

Study on NO2 gas sensing characteristics of In doped ZnO thin films prepared by RF magnetron sputtering

In doped ZnO thin films were prepared on glass substrate by RF magnetron sputtering. The result of XRD and AFM shows that the films are polycrystalline with high c axis orientation. The study of gas sensing reveals that the films are sensitive to NO2 and the best sensibility occurs at 273 ℃; the sensibility is concerned with the concentration of NO2 and the film thickness. The ZnO∶In films are more sensitive to the NO2 gas with higher concentration of NO2 and thinner films have a better sensitivity. Exposed to 2×10-5 NO2 at 273 ℃, the 90nm thick film has a sensibility of 16, indicating that ZnO∶In films can be used to measure NO2 with a low concentration.