Mangrove Habitat Formation and Response to Holocene Sea-level Changes on Kosrae Island,Micronesia

Mangrove habitats on Kosrae are divided into three types, i.e., an estuary or delta type, a backmarsh or lagoon type and a coral reef or tidal-flat type. Most of the mangrove forests of Kosrae have been developed during the last 2000 years by accumulating mangrove peat with the gradual sea-level rise of 1 to 2 mm/yr except the landward part of the estuary or delta type. On the other hand, during the period of rapid sea-level rise of about 10 mm/yr between 4100 and 3700 yr B.P., the mangrove forests ceased peat accumulation and retreated landward. Until 3500 yr B.P., mangrove forests were distributed only in narrow bands in the inlets. Therefore, the critical rate of mangrove peat accretion with sea-level rise is estimated at more than 2 mm/yr and less than 10 mm/yr. If the anticipated sea-level rise exceeds this critical rate, all of the mangrove forests of Kosrae will retreat landward and reduce rapidly.     

The effect of strain, growth stage, and cultivating condition of Ganoderma lucidum on 5α-reductase inhibition

The inhibitory effects of 102 methanol extracts of 40 mycelia, 9 culture fluids, and 53 fruiting bodies of 40 strains of Ganoderma lucidum on 5-reductase were investigated. The methanol extract of the fruiting body of each strain was found to show the strongest 5-reductase inhibitory activity among the extracts tested.     

Characterization of cellulose in compression and opposite woods of a Pinus densiflora tree grown under the influence of strong wind

Summary Structural factors in a Pinus densiflora tree grown under the influence of strong wind were measured. No difference for cellulose molecules was noticed between compression and opposite wood, but the was somewhat lower in the region where the compression wood was concentrated. The degree of crystallinity of cellulose was 45–50% in compression wood, about 50% in normal wood, and 50–60% in opposite wood. The crystallinity decreased with increasing height above the ground. The maximum point of crystallographic b-axis (fiber axis) orientation distribution for cellulose crystallites in compression wood was located at 30°, in normal wood at 25° and in opposite wood at 0°. The cellulose crystallite dimension in the transverse direction was 3.2 nm, corresponding to four cellulose unit cells, a value that was almost constant throughout the wood. In the longitudinal direction, there were large differences in cellulose crystallite dimensions between compression and opposite woods. In compression wood the cellulose crystallite dimensions was 12 nm corresponding to 11–12 cellulose unit cells. In opposite wood it was 17–32.5 nm corresponding to 17–32 cellulose unit cells. These structural factors were apparently affected by the environmental conditions, and the mechanical properties of the wood were influenced by these factors. Opposite wood had longer crystallites, a higher degree of crystallinity and a better orientation distribution of cellulose crystallites in the longitudinal direction. Compression wood, on the other hand, had shorter crystallites, a lower degree of crystallinity and a large angle between the stem and the direction of the crystallites.     

Variations in transpiration rate and leaf cell turgor maintenance in saplings of deciduous broad-leaved tree species common in cool temperate forests in Japan

To clarify mechanisms underlying variation in transpiration rate among deciduous broad-leaved tree species, we measured diurnal changes in stomatal conductance (gs) and leaf water potential, and calculated the maximum transpiration rate (Emax), leaf-specific hydraulic conductance (K(s-l)) and difference between the soil water potential and the daily minimum leaf water potential (Psis - Psi(l,min)). Pressure-volume (P-V) measurements were made on leaves. Saplings of eight broad-leaved tree species that are common in Japanese cool temperate forests were studied. Maximum transpiration rate varied significantly among species. There was a statistically significant difference in Psis - Psi(l,min), but not in K(s-l). Species with large Emax also had large Psis - Psi(l,min) and gs. The results of the P-V analyses showed that species with a large Psis - Psi(l,min) maintained turgor even at low leaf water potentials. The similar daily minimum leaf pressure potentials (Psip) across all eight species indicate that Psip values below this minimum are critical. Based on these results, we suggest that the leaf cell capacity for turgor maintenance strongly affects Psis - Psi(l,min) and consequently Emax via stomatal regulation.     

The method for designing the profile of forest roads supported by genetic algorithm

This study examines a method for designing an optimum profile of a forest road in a short matter of time. In this method, a genetic algorithm (GA) searches for points where the gradient changes and dynamic programing (DP) designs the longitudinal slope. This method can be applied to the ground heights of an actual forest road. The evaluation function of the DP assesses the total expenditure. The inverse of this function is the fitness function. Crossover and mutation are operators of an evolution simulation of a GA. They are each repeated 20 times and 420 profiles are designed and assessed, all within about 10 min. A comparison of the profile designed by the GA with that of an actual forest road shows only one section where the formation level differed substantially. Overall, both profiles seem to show a high degree of correspondence. From this result, we believe that the profile designed by the GA is best, or the one of the best. A conventional method takes about 65 h to calculate all changing points of gradients. However, by using the GA, the calculation time was reduced to about 1/389 that of the coventional method, showing that the method which uses the GA through the profile design is very useful.     

松香酰胺在中性造纸施胶中的应用

利用松香与异腈酸的酰经反应在１００－１５０℃下合成了三个松香酰胺，并应用它们到中性造纸松香乳酸，ＰＨ４－８的抄造试验表明这些松香衍生物在这个ＰＨ范围内具有高的施胶效果。松香酰结构与酰胺化度对施胶效果有很大的影响。     

Inoculation of fumigated nursery soil increases nodulation and yield of bare-root red alder (Alnus rubra Bong.)

To determine if inoculation increases nodulation and yield of bare-root red alder (Alnus rubra Bong.), fumigated nursery plots were treated with inoculum and ammonium sulfate (28 kg N ha^–1) in a factorial experiment. Inoculum was alder soil with 100 infective units of Frankia g^–1. Seedlings were evaluated for nodulation at age 10 wk and when lifted, at age 9 mo. Inoculation produced earlier and more extensive nodulation and increased seedling root collar diameter, height, and dry weight. Fertilization decreased seedling height, but did not decrease nodulation. No interaction of fertilization with inoculation was found. Inoculated unfertilized plots had the highest yield of packable seedlings (257 m^–2), and uninoculated fertilized seedlings had the lowest yield (126 m^–2).     

Automatic detection of washboarding in bandsaws

This paper presents an on-line method for detecting washboarding generated in bandsaws. It uses a parameter based on the shape of sawing force amplitude distributions. The curve of the probability density function of the parallel sawing force amplitude obeyed a normal distribution for the normal sawn surface, but it changed to an M-shaped distribution when washboarding appeared on the sawn surface of the workpiece. The curve of probability density function of the normal sawing force amplitude obeyed the normal distribution for any sawn surface investigated. The workpiece including a knot did not influence use of the parameter for detecting the appearance of washboarding.