The Algorithm of Searching out the Least and Most Loops by Making Use of Direction Factor

Based upon the conception of the least loop,the most loop and direction factor presented by the author firstly,the algorithm of searching out the least and most loops has been designed.By building the adjoining matrix, confirming the start-point of searching,vectorizing the searching sides,calculating the direction factor of adjoining sides,we can search out the next side of the least loop or the most loop rapidly.With a valid searching side being confirmed at every searching and the searching scope being reduced by forming degenerate graph,the time compexity of the algorithm is much less. In the research of the automatic calculating system of construction quantities, the problem of houses partition and out-wall partition had been solved succesfully by utilizing this searching algorithm.     

稻谷固定床深层干燥的计算机模拟

针对稻谷固定床深层间歇干燥过程中的加热和缓苏两个阶段建立了数学模型，用C语言编制了相应的运算程序。用该模型计算了不同干燥介质温度和湿度、不同粮食初始含水率和温度条件下，不同层厚处稻谷的含水率和温度，计算结果与试验结果基本相符。     

基于虚拟仪器的农产品"身份证"数字识别系统

介绍了基于虚拟仪器图形化语言LABVIEW开发的农产品"身份证"数字识别系统,采用CCD摄像机对农产品"身份证"编号进行采集,通过PCI-1411彩色图像采集卡将图像传输到计算机并进行图像处理,最后应用美国NI公司的OCR软件包对处理好的编号进行识别.结果表明,该系统抗干扰能力强且精度高.     

泵站中钢筋混凝土梁加固的变形计算

基于试验研究资料的分析,对于大型泵站中具有合适锚固的CFRP片材加固受弯构件变形计算方法进行研究,认为加固梁的弯矩-曲率曲线符合三线型规律（混凝土开裂前,混凝土开裂后,受拉钢筋屈服后）.通过解析分析,得到试验梁在通常两点加载条件下的任一加载阶段的弯矩及变形计算公式,与相应条件试验梁的试验测试结果吻合,可为泵站工程设计规程的制定提供参考。     

可视化编程技术在发动机外特性曲线绘制中的应用

通过对汽车发动机外特性的理论分析,在处理汽车发动机外特性曲线时,建立了一种适合处理发动机外特性曲线的三次样条函数拟合的数学模型,在C Builder可视化开发平台上,编制了汽车发动机外特性曲线绘制程序.利用三次样条函数插值法对实验数据进行拟合,实现了发动机外特性曲线绘制的自动化.     

轴流定桨式水轮机抬机事故分析及防止措施

对小型水电站轴流定桨式水轮发电机组的抬机现象进行了分类，从理论上分析了造成抬机现象的原因，并结合试验研究和现场处理经验，提出了防止抬机事故的几项措施。     

Modeling soil water dynamics in a drip-irrigated intercropping field under plastic mulch

Intercropping, drip irrigation, and the use of plastic mulch are important management practices, which can, when utilized simultaneously, increase crop production and save irrigation water. Investigating soil water dynamics in the root zone of the intercropping field under such conditions is essential in order to understand the combined effects of these practices and to promote their wider use. However, not much work has been done to investigate soil water dynamics in the root zone of drip-irrigated, strip intercropping fields under plastic mulch. Three field experiments with different irrigation treatments (high T1, moderate T2, and low T3) were conducted to evaluate soil water contents (SWC) at different locations, for different irrigation treatments, and with respect to dripper lines and plants (corn and tomatoes). Experimental data were then used to calibrate the HYDRUS (2D/3D) model. Comparison between experimental data and model simulations showed that HYDRUS (2D/3D) described different irrigation events and SWC in the root zone well, with average relative errors of 10.8, 9.5, and 11.6 % for irrigation treatments T1, T2, and T3, respectively, and with corresponding root mean square errors of 0.043, 0.035, and 0.040 cm³ cm^?3, respectively. The results showed that the SWC in the shallow root zone (0–40 cm) was lower under non-mulched locations than under mulched locations, irrespective of the irrigation treatment, while no significant differences in the SWC were observed in the deeper root zone (40–100 cm). The SWC in the shallow root zone was significantly higher for the high irrigation treatment (T1) than for the low irrigation treatment, while, again, no differences were observed in the deeper root zone. Simulations of two-dimensional SWC distributions revealed that the low irrigation treatment (T3) produced serious severe water stress (with SWCs near the wilting point) in the 30–40 cm part of the root zone, and that using separate drip emitter lines for each crop is well suited for producing the optimal soil water distribution pattern in the root zone of the intercropping field. The results of this study can be very useful in designing an optimal irrigation plan for intercropped fields.     

专家控制技术在设施园艺中的应用

设施园艺环境有多因素、线性大、时间滞后和不确定性的特点。随着现代化控制技术的发展,专家控制技术可以取得较好的控制效果。为此,介绍了专家控制技术的基本概念和其在温室环境控制中的应用,并叙述了知识库、数据库和推理机的设计过程。     

Crop water requirements for rainfed and irrigated grain corn in China

A basic parametric crop water use model (WATER) that employes climatic and environmental data to calculate temporal and spatial water consumption for a variety of major corps was applied specifically for grain corn to the region of China and Korea to investigate the evapotranspiration (ET) demand on grain corn and the associated irrigation water applications necessary for optimal crop production. A network of 241 stations provided the seasonal climatic input. The climatic input consisted of data averaged over approximately a 20 year period. Among the results, highest ET under full irrigation (first harvest) occurred in the northwestern inland sections of China, whereas least ET was found for the southeast. Under rainfed conditions, the relationship became nearly inverse. In order to achieve optimum crop yields, about 1000 mm of irrigation water was needed in the northwest, contrasted with none required in the south and east of China. A sensitivity analysis was applied to determine the degree of error introduced by faulty or uncertain environmental input data.