Cutter head forces and load cell scanning

Among the machinery found in wood manufacturing industries, routers and planers are the most commonly used. These tools, which many times are mounted on metal cylinders, actually operate only briefly, i. e., when a chip is cut from a piece of wood under process. The rest of the time the knife follows the cylinder surface and a cycloid is formed relative to the work piece, which in turn is fed into the machine. A number of knives are mounted on the cutter, which ascertain that the planed surface will become sufficiently planed and does not show too a wavy pattern. This works fine for high revolutions and low feeding speeds even if problems sometimes occur. Factories, however, naturally want to increase the overall manufacturing speed, which means that at the same time more defects are introduced at the planed surface. These defects are the result of the cutting process. In this paper, we examine, by use of a load cell, how the cutting forces vary during the formation of a wood chip. Wood is not an isotropic material and knots and other anomalies make the evaluation harder. In order to simplify the conditions, experiments are also shown from the cutting of a plastic polymer material as well as Medium Density Fibreboard (MDF). It is shown that the work piece vibrated intensely which littered all output data from the cell. Experience from the experiments however made it possible to design a computerised filter which saved only those registrations which were of interest while the others were set to zero. For beech, the forces were found to be of the magnitude 50 N/cm opposite to the feeding direction while the tranverse forces changed signs and had a magnitude of about 5 N/cm.     

Optimization and fundamentals of high-yield pulping with ethanol

Summary A new high-yield pulping process based on ethanol pretreatment and steam cooking was studied. The effect of processing conditions (cooking temperature at six levels and ethanol concentration at five levels) was determined. Optimum results appeared at 30% ethanol concentration and with cooking at 195 °C. The cooking liquor was analyzed by GC-MS and low-molecular lignin fragments were identified. Alcohol in alkaline medium destroys the three-dimensional lignin structure by cleavage of ether bonds, increases the penetration of the impregnation solution (higher sulfonation) and solubilizes lignin.Ethanol treatment facilitates fiber separation in the middle lamella. Pulp prepared under optimal conditions has higher flexibility, conformability and better bonding ability when compared with other samples. Higher concentrations of ethanol (above 30%) might cause precipitation of lignin on the fiber surface.The authors wish to thank the NSERC of Canada, FCAR of Quebec, Stake Tech. Co. and CQVB for their financial support. Special thanks are extended to the Stazione Sperimentale per la Cellulosa, Carta e Fibre Tessili, Vegetali ed Artificiali, Milan, Italy, for the microscopy and X-ray measurements and to the Department of Chemical Technology of Wood, Pulp and Paper, Faculty of Chemical Technology, Slovak Technical University, Bratislava, Slovakia for their expertise in GC-MS     

Leaf distribution in large trees and stands of the floodplain forest in southern Moravia

Vertical distributions of leaf dry mass (M(d)) and leaf area (A(f)) were related to relative irradiance (I(r); I(r) above the stand = 1) in closed-canopy, old-growth stands of the floodplain forest in southern Moravia composed largely of Quercus, Fraxinus and Tilia species. Foliage area and mass at any given canopy height were converted to solar equivalent leaf area (A(s)) and mass (M(s)) by multiplying actual values at a given level in the canopy by the relative irradiance at that position. Stand leaf area index (LAI) was 5 (7 including shrub and herb layer), and solar equivalent parameters reached about 25% of that amount. In all species, vertical profiles of both relative irradiance and leaf dry mass to area ratio (LMA) were sigmoidal and the two variables were linearly related. The dominant, upper canopy species had a larger proportion of solar equivalent foliage than suppressed understory species. For individual trees of all species, the upper canopy had a larger proportion of solar equivalent foliage than the lower canopy. Light compensation points at both the leaf and whole-tree level were defined according to leaf or tree position, size and structure. I conclude that optimization of A(s) for forest stands may be used as a basis for determining thinning schedules and evaluating tree survival after damage to tree crowns by various factors.     

The effects of temporal differences between map and ground data on map-assisted estimates of forest area and biomass

Key message

When areas of interest experience little change, remote sensing-based maps whose dates deviate from ground data can still substantially enhance precision. However, when change is substantial, deviations in dates reduce the utility of such maps for this purpose.

Context

Remote sensing-based maps are well-established as means of increasing the precision of estimates of forest inventory parameters. The general practice is to use maps whose dates correspond closely to the dates of ground data. However, as national forest inventories move to continuous inventories, deviations between map and ground data dates increase.

Aims

The aim was to assess the degree to which remote sensing-based maps can be used to increase the precision of estimates despite differences between map and ground data dates.

Methods

For study areas in the USA and Norway, maps were constructed for each of two dates, and model-assisted regression estimators were used to estimate inventory parameters using ground data whose dates differed by as much as 11 years from the map dates.

Results

For the Minnesota study area that had little change, 7-year differences in dates had little effect on the precision of estimates of proportion forest area. For the Norwegian study area that experienced considerable change, 11-year differences in dates had a detrimental effect on the precision of estimates of mean biomass per unit area.

Conclusions

The effects of differences in map and ground data dates were less important than temporal change in the study area.

     

Stand biometry and leaf area distribution in an old olive grove at Andria, southern Italy

The objectives of this paper were (1) to provide general biometry data for an 80-year-old olive (Olea europea L., cv. Coratina) grove in Andria, southern Italy, and (2) to compare different methods for estimating leaf area distributions. Stand biometry was represented by a stocking density of 132 trees ha^?1, mean spacing of 8.7 m and mean social area (proportional to spacing and tree size) of about 76 m² per tree. Trunk total circumference averaged 110 cm and after subtraction of missing or dead parts of stems averaged 81 cm, projected area of crowns averaged 17.7 m² and the mean tree height was 4.9 m. Leaf distribution was evaluated using calibrated ground-based side photographs through image analysis and through using a simple canopy-layer model (considering hollow volume within tree crowns) and double-Gaussian curves. The mean leaf size was about 5 cm² (distributed in a log-normal manner over the range of 2 to 12 cm²). Considering whole tree crowns, the mean leaf density was about 2.6 m²m^?3; the maximum leaf area occurred in canopy layers between 1.5 to 3 m, tailing with a steeper slope to the crown base and a less steep slope to the tree-top. The foliated volume of olive crowns (mean 33.2 m³) contained on average 145 thousand leaves of the total area of 72.6 m². The corresponding leaf area index on the stand level (LAI _grove = 0.96), was rather low due to low stocking density. However when taking into account only the projected crown areas (and avoiding free space between trees), the mean LAI reached about 3.5 (range from 1–7). The radial pattern of leaf distribution derived from image analysis indicated peak LAI _rad values at a distance from the stem of about 60 to 70% of crown radius in trees of different size. The applicability of different approaches to the estimation of the necessary allometric parameters is discussed.     

Comparison of chitosans with different molecular weights as possible wood preservatives

Fungi cause serious problems in wood utilization, and environmentally benign wood protection is required as an alternative to traditional chemicals. Chitosan has shown promising antimicrobial properties against several microorganisms. In this study, we present the characterization of and antifungal properties of a commercial chitosan formulation developed for impregnation of wood. A broad range of chemical and mycological methods were used to evaluate the uptake, fixation, and antifungal properties of chitosan for wood preservation. The results show that the higher the uptake of chitosan the lower the relative recovery of chitosan in wood after leaching, and the higher the molecular weight of chitosan the higher the recovery. Chitosan with high molecular weight proved to be more efficient against decay fungi than chitosan with low molecular weight. The fungi tested on chitosan-amended nutrient agar medium were totally inhibited at 1% (w/v) concentration. In decay studies using small wood blocks, 4.8% (w/v) chitosan concentration gave the best protection against brown rot fungi.     

Predicting moisture content and density distribution of Scots pine by microwave scanning of sawn timber II: evaluation of models generated on a pixel level

The purpose of this study was to use images from a microwave sensor on a pixel level for simultaneous prediction of moisture content and density of wood. The microwave sensor functions as a line-scan camera with a pixel size of 8mm. Boards of Scots pine (Pinus sylvestris), 25 and 50mm thick, were scanned at three different moisture contents. Dry density and moisture content for each pixel were calculated from measurements with a computed tomography scanner. It was possible to create models for prediction of density on a pixel level. Models for prediction of moisture content had to be based on average values over homogeneous regions. Accuracy will be improved if it is possible to make a classification of knots, heartwood, sapwood, etc., and calibrate different models for different types of wood. The limitations of the sensor used are high noise in amplitude measurements and the restriction to one period for phase measurements.     

Effects of elevated CO(2) concentration and nutrition on net photosynthesis,stomatal conductance and needle respiration of field-grown Norway spruce trees

To study the effects of elevated CO(2) on gas exchange, nonstructural carbohydrate and nutrient concentrations in current-year foliage of 30-year-old Norway spruce (Picea abies (L.) Karst.) trees, branches were enclosed in ventilated, transparent plastic bags and flushed with ambient air (mean 370 &mgr;mol CO(2) mol(-1); control) or ambient air + 340 &mgr;mol CO(2) mol(-1) (elevated CO(2)) during two growing seasons. One branch bag was installed on each of 24 selected trees from control and fertilized plots. To reduce the effect of variation among trees, results from each treated branch were compared with those from a control branch on the same whorl of the same tree. Elevated CO(2) increased rates of light-saturated photosynthesis on average by 55% when measured at the treatment CO(2) concentration. The increase was larger in shoots with high needle nitrogen concentrations than in shoots with low needle nitrogen concentrations. However, shoots grown in elevated CO(2) showed a decrease in photosynthetic capacity compared with shoots grown in ambient CO(2). When measured at the internal CO(2) concentration of 200 &mgr;mol CO(2) mol(-1), photosynthetic rates of branches in the elevated CO(2) treatments were reduced by 8 to 32%. The elevated CO(2) treatment caused a 9 to 20% reduction in carboxylation efficiency and an 18% increase in respiration rates. In response to elevated CO(2), starch, fructose and glucose concentrations in the needles increased on average 33%, whereas concentrations of potassium, nitrogen, phosphorus, magnesium and boron decreased. Needle nitrogen concentrations explained 50-60% of the variation in photosynthesis and CO(2) acclimation was greater at low nitrogen concentrations than at high nitrogen concentrations. We conclude that the enhanced photosynthetic rates found in shoots exposed to elevated CO(2) increased carbohydrate concentrations, which may have a negative feedback on the photosynthetic apparatus and stimulate cyanide-resistant respiration. We also infer that the decrease in nutrient concentrations of needles exposed to elevated CO(2) was the result of retranslocation of nutrients to other parts of the branch or tree.     

Farmers' production of timber trees in the cacao-coffee region of coastal Ecuador

The coastal region of Ecuador is an important producer of cacao and coffee. Increasingly, farms and ranches in the region also provide industrial wood for sawmills and other wood processing plants. Most of this wood derives from shade trees and pasture trees. Because little is known of wood supply from farm sources in coastal Ecuador, a survey was conducted of 122 farmers in the subregions of Ventanas, La Troncal, and Babahoyo. The survey indicates an abundance of land for the growing of farm trees, and excellent regeneration of many species on the majority of farms. However, current stocking of farm trees seems well below potential, and fewer than half of interviewed owners deliberately manage farm trees for eventual sale as timber. Only 2.2 percent of gross farm revenue derives from tree sales, even though over half of surveyed farmers have sold trees to industrial buyers at least once. Constraints on production and sales of farm trees for timber include risks of damage to coffee and cacao; perceived incompatibilities with current farming practices; inadequate methods of classification and pricing of farm trees; and insufficient knowledge of the industrial uses of farm trees by agricultural extensionists. These limitations need to be addressed through a strategy of research, development, and information diffusion on selected demonstration farms.

---

Resúmen La región costera del Ecuador es una productora importante de cacao y café. Cada vez más, las fincas de la región proveen madera industrial para asseraderos y otros procesores madereros. La mayoría des esta madera viene de árboles de sombra. Dado que se sabe poco de la cantidad de madera provieniente de fincas en la costa del Ecuador se hizo una encuesta a 122 agricultores en las subregiones de Ventanas, La Troncal, y Babahoyo. La encuesta indica que existe una abundancia de terreno disponible para la producción de árboles de sombra y una regeneración excelente de muchas especies en la mayoría de las fincas. Sin embargo, densidades de los árboles de sombra parece bastante debajo de su nivel potencial, y menos de la mitad de los agricultores entrevistados cultivan sus árboles con el fin de venderlos eventualmente. De los entrevistados, un promedio de 2,2 porciento de ingresos brutos anuales provienen de ventas de árboles, a pesar de que más de la mitad de los agricultores han vendido árboles a compradores industriales por lo menos una vez. Limitaciones a la producción y a la venta de estos árboles incluyen el riesgo de daños a las plantas de cacao y cafe; la percibida incompatibilidad con las prácticas agrícolas usuales, métodes inadecuados de clasificar y poner precio a los árboles, y el poco conocimiento de los usos industriales de árboles de sombra por parte de los extensionistas agrícolas. Se necesita enfocar atención a estas limitaciones a través de una estrategia de investigación, desarrollo, y difusión de información en seleccionadas fincas demonstrativas.

     

Factors affecting costs for on-farm control of salmonella in Swedish dairy herds

Background

The Swedish control program for salmonella includes restrictions and on-farm control measures when salmonella is detected in a herd. Required control measures are subsidised by the government. This provides an opportunity to study costs for on-farm salmonella control. The aim of this study was to describe the costs for on-farm salmonella control in Swedish cattle herds and to investigate the effects of herd factors on these costs in dairy herds.

Results

During the 15 years studied there had been a total of 124 restriction periods in 118 cattle herds; 89 dairy herds, 28 specialised fattening herds and three suckler herds. The average costs per herd for on-farm salmonella control was 4.60 million SEK with a median of 1.06 million SEK corresponding to approximately 490 000 and 110 000 EUR. The range was 0.01 to 41 million SEK corresponding to 1080 EUR to 4.44 million EUR per farm. The costs cover measures required in herd-specific control plans, generally measures improving herd hygiene. A mixed linear model was used to investigate associations between herd factors and costs for on-farm salmonella control in dairy herds. Herd size and length of the restriction period were both significantly associated with costs for on-farm control of salmonella with larger herds and longer periods of restrictions leading to higher costs. Serotype detected and administrative changes in the Swedish Board of Agriculture aiming at reducing costs were not associated with costs for on-farm salmonella control.

Conclusions

On-farm control of salmonella in Swedish cattle herds incurred high costs but the costs also varied largely between herds. Larger herds and longer restriction periods increased the costs for on-farm control of salmonella in Swedish dairy herds. This causes concern for future costs for the Swedish salmonella control program as herd sizes are increasing.