Chemical synthesis of polypyrrole film and its adsorption capacity for aromatic polycarboxylic acids

Polypyrrole (PPy) film was prepared via in-situ chemical polymerization of pyrrole monomer on the surface of red-clay-brick (RCB) substrate. The deposited PPy film was characterized and used as an adsorbent for removal of benzene polycarboxylic acids from aqueous solutions. The effects of solution pH, contact time, initial concentration, and temperature on the adsorption process were systematically investigated to find the optimum operating conditions. Adsorption kinetic data were best fitted by pseudo-second order kinetic model. The adsorption equilibrium data were most represented by the Freundlich isotherm model. The maximum adsorption amounts of Trimellitic, Hemimellitic, and Pyromellitic acids were 189.27, 177.26, and 203.31 mg/g, respectively. The thermodynamic studies indicate that the adsorption was an endothermic and spontaneous process. Also, the PPy-RCB film was successfully regenerated using sodium hydroxide solution. The regenerated PPy-RCB can be reused for more than four successive cycles with a low reduction in adsorption efficiency.     

Influence of synergism caused by organic montmorillonite and nanometer calcium carbonate on mechanical properties and crystallization of polyamide 1010-based composites

This account showed that nanometer-active calcium carbonate (CaCO₃) improved polyamide 1010/organic montmorillonite (OMMT) composites and OMMT boosted polyamide 1010/CaCO₃. The mechanical performance suggested the composites to be reinforced through adsorption forces present between the nanofillers and the matrix. The synergistic effect of CaCO₃ and OMMT increased the yields and shrunk cavities when observed by scanning electron microscopy. The obvious resulting synergism was verified by X-ray scattering techniques after the addition of OMMT. The concentration of CaCO₃ did not change lamellar-size or influence the crystal growth. The effect of CaCO₃ on melting behavior was found less significant than that exert on crystallization behavior.     

Effects of date palm leaf fiber on the thermal and tensile properties of recycled ternary polyolefin blend composites

This work investigated the effects of date palm leaf fiber (DPLF) content on the thermal and tensile properties; and morphology of compatibilized polyolefin ternary blend. Recycled polyolefin ternary blend consisting of low density polyethylene (RLDPE), high density polyethylene (RHDPE) and polypropylene (RPP) were fabricated at different parts per hundred resin (phr) of DPLF. Maleic anhydride grafted polyethylene (MAPE) was used as compatibilizer to enhance the adhesion between filler and polymer matrix. The composites were prepared using melt extrusion and tests samples were produced via injection molding process. Thermal conductivity results showed that as much as 11 % reduction in thermal conductivity was achieved with the incorporation of 30 phr DPLF. Highest tensile strength was observed with the incorporation of 10 phr DPLF. The elongation at break was reduced with the addition of DPLF due to impediment of chain mobility by the fillers. Initial degradation temperature increased with the addition of DPLF. Hence, it is concluded that DPLF can be used to develop green and thermally insulating composites. It is hoped that the present results will stimulate further studies on the thermally insulative materials based on natural fibers reinforced polymer composites for applications in the building industries.     

Characterization of the surface properties of cellulosic fibers in fibrous and ground forms by IGC and contact angle measurements

Surface properties of fibrous and ground cotton and linen were investigated by inverse gas chromatography (IGC) and the contact angle with different liquids was also measured on fabrics composed of both fibers. Results proved that dispersion component of surface tension (γ _s ^d ) determined by IGC depends not only on the surface energy, but also on several factors influencing the adsorbability of probe molecules on the cellulosic substrates. For cotton samples, the trapping of n-alkanes among waxy molecules in the outer layer of fibers can be presumed. This effect results in larger γ _s ^d for cotton fibers than for linen in spite of the higher wettability of the linen fabrics. Besides the surface energy and trapping effects, the grinding also influences the γ _s ^d values. Specific enthalpy of adsorption (ΔH _A ^ab ) of polar probes could be determined on all linen samples, but only on the ground cotton sample. Lewis acid-base character calculated for linen and ground cotton samples depends on the same effects as the γ _s ^d does. The similar ΔH _A ^ab values of chloroform (acidic) and THF (basic) measured on each of the samples support the conclusion that the surface character is amphoteric, which is also proved by the high ΔH _A ^ab values of the amphoteric ethyl acetate and acetone probes.     

Polyvinylidene fluoride nanofiber coated polypropylene nonwoven fabric as a membrane for lithium-ion batteries

Polyvinylidene fluoride (PVdF) membranes in spite of having many critical properties necessary for lithium-ion batteries, do not have satisfying thermal and mechanical resistance. The goal of this study was to combine the good mechanical and thermal properties of PP nonwoven fabric with the excellent electrochemical properties of PVdF nanofibers to exploit a high-performance membrane for lithium-ion batteries. This work reports the preparation of PVdF nanofiber membranes using electrospinning on a polypropylene (PP) spunbonded nonwoven fabric and an aluminum foil followed by a hot-pressing treatment. The morphology and size of the membranes were studied by the scanning electron microscopy. The tensile strength of the membrane with the PP support was superior to the PVdF membrane. Thermal stability of the prepared membranes was determined using the TGA method and the dimensional stability was investigated by measuring the shrinkage ratio at 105 °C. The results have shown that the PVdF/PP membrane was thermally more stable than the PVdF and the commercial Celgard 2325 membranes. The batteries using PVdF/PP membrane exhibited higher electrochemical oxidation limit, better cycling performance and less discharge capacity fading during 100 cycles compared to PVdF and Celgard membranes. The results of this study showed that PVdF/PP membrane is a promising advanced membrane in lithium-ion batteries.     

Preparation and properties of solid polymer electrolyte based on imidazolium-based ionic liquids for structural capacitors

We prepared solid polymer electrolytes (SPEs) composed of poly(ethylene glycol) monomethyl ether acrylate (1A9OMe) and 1-ethyl-3-methylimidazolium trifluoromethanesulfonate ([EMIm][OTF]) and 1-ethyl-3-methylimidazolium bis(trifluoromethane sulfonyl) imide ([EMIm][TFSI]) as the ionic liquid. The SPEs formed by appropriately adding ionic liquids in the 1A9OMe prior to thermal cure. The ratio of 1A9OMe and ionic liquid was 1:9, 3:7, and 5:5, respectively. The characterization of solid polymer electrolytes were investigated using Fourier transform infrared spectroscopy in the attenuated total reflectance mode (FTIR-ATR), Electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and glavanostatic charge-discharge test. The highest ionic conductivity of SPEs was found to be 4.90×10^?4 S/cm in a 1A9OMe/[EMIm][OTF] of 3:7. As IL contents were increased, the specific capacitance of supercapacitor was increased. The specific capacitance of supercapacitor for ionic liquid with large ion size was lower than that for ionic liquid with smaller ion size.     

Synthesis of hydrophobic anthraquinoid magenta dyes having linear alkyl substituents

A new series of magenta dyes having different length of alkyl substituents was synthesized to dye unmodified polypropylene (PP) and ultra-high molecular weight polyethylene (UHMWPE) fiber. It could be concluded that the affinity of the dyes onto unmodified PP and UHMWPE fibers was increased with the increase of the length of alkyl substituents. The optimum length of alkyl group was determined as the longest dodecyl-substituted dye in this study. Their absorption spectra appeared almost the same at visible range, which meant that the length of alkyl substituents did not affect the color appearance of the dyes. The color fastness properties of the dyeings to washing, rubbing and light were good enough for commercialization.     

Copolymerization of benzyl methacrylate and a methacrylate bearing benzophenoxy and hydroxyl side groups: Monomer reactivity ratios,thermal studies and dielectric measurements

Statistical copolymers of 2-hydroxy-3-benzophenoxy propyl methacrylate (HBPPMA) and benzyl methacrylate (BzMA) in different feed ratios were synthesized by free radical copolymerization method at 60 °C in presence of AIBN initiator. The compositions of copolymer were estimated from ¹H-NMR technique. The monomer reactivity ratios of HBPPMA and BzMA were calculated as r₁ (r_HBPPMA)=0.51±0.076 and r₂ (r_BzMA)=1.07±0.140 for Kelen-Tüdos method, and was estimated as r₁=0.37±0.0006 and r₂=0.64±0.0485 according to Fineman Ross equation. The average values estimated from the two methods showed that monomer reactivity ratio of benzyl methacrylate was a slightly high in comparison to HBPPMA. The copolymer system showed an azeotropic point, which is equal to M _BzMA =m _BzMA =0.43. DSC measurements showed that the T_g’s of poly(HBPPMA) and poly(BzMA) were 84 °C and 73 °C, respectively. The T_g in the copolymer system decreased with increase in benzyl methacrylate content. The decomposition temperature of poly(BzMA) and poly(HBPPMA) occurs in a single stage at about 207 °C and 260 °C, respectively. Those of HBPPMA-BzMA copolymer systems are between decomposition temperatures of two homopolymers. The dielectric constant, dielectric loss factor and electrical conductivity were investigated depend on the frequency of the copolymers. The highest dielectric constants depending on all the studied frequencies were recorded for the poly(HBPPMA) and the copolymer containing the highest HBPPMA unit. The dielectric constant for P(HBPPMA) and P(BzMA) at 1 kHz are 6.56 and 3.22, respectively. Also, those of copolymer systems were estimated between these two values. Similarly, poly(HBPPMA) and copolymers, which are prepared under the same conditions show the dissipation factor and conductivity as well.     

Numerical analysis of injection molding for the Syringe Barrel with optimum design and processing condition

The numerical analysis was performed to predict the potential problem, often occurring during the manufacturing process of the disposable medical device of a great volume. The cavity filling analyses were performed for the new design of the 3cc Syringe Barrel using polypropylene(PP1), and a new nucleated polypropylene(PP2) material for better clarity. These analyses have been performed for different processing conditions as well as various wall thickness designs for both materials. With the nucleated material, only the original wall thickness design has been studied at two different processing conditions for comparison purpose. This study was conducted to investigate the optimum part design and processing condition for two different materials. The most desirable design was selected with Design 3 for material utilization and reduced flow stresses by comparing the field results. The new nucleated polypropylene provided slightly better product quality and processing.     

Application of silver nanoparticles as an antibacterial mordant in wool natural dyeing: Synthesis,antibacterial activity,and color characteristics

Madder is a natural colorant which is commonly applied with metal salts as a mordant to improve its affinity to fibers and color fastness. Madder produces an insoluble complex or lake in the presence of metal ions on mordanted fabric. In this study, wool fabric was pretreated with AgNPs (silver nanoparticles) as a mordant, then dyed with madder. The wool fabric samples were examined by scanning electron microscopy (SEM) and their colorimetric characteristics were evaluated. The formation of spherical silver nanoparticle was confirmed using UV-Visible spectroscopy, SEM images, and elemental analysis. The average size of synthesized silver nanoparticles on the surface of wool fibers is around 73 nm. The dyed wool samples were pretreated with different concentration of Ag⁺ ions or AgNPs, which showed higher color strength value compared to untreated dyed wool fabric. This pretreatment also presented good antibacterial activity.