Effects of zero and conventional tillage on the length and irregularity of elongated pores in a clay loam soil under viticulture

Total porosity and width, length and irregularity of elongated pores from thin sections, prepared from undisturbed Ap horizon samples taken from a zero versus conventional-tillage field experiment, were analysed by means of a Quantimet 720 System 23 image analysing computer. Both total porosity and elongated pore area were significantly higher in conventionally-tilled plots. On the contrary, both the total number of pores and the proportion of elongated pores were significantly higher in no-tilled plots. Thus, zero tillage reduced the size of pores. Conventional tillage caused an increase in the length of a few large, elongated pores which also showed very strong irregularity. In samples from no-tilled plots the total length of elongated pores was smaller, but these pores were more numerous and more regular than in samples from conventionally-tilled plots. Consequently, soil conditions for root growth were better.     

Performance evaluation of tillage tines operating under different depths in a sandy clay loam soil

The study investigated the performance of three model tillage tools (tines). The experimental tillages were made from flat 8 mm plain carbon steel. They were designated T1, T5, and T20, corresponding to tine widths of 1, 5, and 20 cm respectively. Experiments were carried out in a soil bin filled with sandy clay loam soil at average moisture content 11.5% (dry basis) and 600 kPa average cone index. The plastic limit and liquid limit and plasticity index of the soil are 20%, 31% and 11% respectively. Tests were conducted at forward speeds of 0.28, 1.0, and 2.5 m/s. Depths of operation considered were 35, 70, 150, 200 and 250 mm. Draught measurements were made for the different tines and were also calculated using soil mechanics equation. There was reasonable agreement between measured and predicted draught forces. The effects of depth of operation on draught force of the tines were studied and evaluated. It was observed that draught increased at an increasing rate with depth; the relationship was a curvilinear one best fitted by exponential function. The soil disturbance created as a result was also evaluated and reported in this paper. The parameters used to define soil disturbance of a single tine were: ridge-to-ridge distance (RRD), maximum width of soil cut (WFS), maximum width of soil throw (TDW), after furrow depth (df), height of ridge (hr) and rupture distance (f). They all increased as the depth of operation of the tool increased but less proportionately. The critical depth of the tines was also estimated.The results of analysis of variance showed that tool type and operating depth significantly affected draught at 5% level of significance (p < 0.05) and that, there was interaction between the two factors.     

Impact of tillage intensity on clay loam soil structure

Soil structure and structural stability are key parameters in sustainable soil management and optimum cropping practices. This study aimed to improve the knowledge of potential precision tillage practices by characterizing the effect of varied tillage intensities on structural properties of a clay loam soil. An experiment with seedbed preparation was conducted using a power take‐off‐driven rotovator equipped to measure torque and angular velocity and with operational speed (OS) and rotational speed (RS) as main factors. Effects of soil coverage prior to tillage and wheeling directly after tillage were measured at one combination of OS and RS. The soil was sampled at 0–80 mm depth. Under slow OS (2.9 km hr^?1) compared with fast OS (6.3 km hr^?1), specific energy input was greater (116 and 52 J kg^?1 on average, respectively), and it increased with RS. Wheeling resulted in larger aggregate diameter right after tillage (at T1; 56 mm as geometric mean compared with 9 mm), with 42 times smaller geometric mean of air permeability 45 days after tillage (at T2) and with greater soil dispersibility at T2. Highly significant correlations were observed between soil dispersibility and energy input, specific surface area of aggregates, fractions of small (<4 mm) and medium (8–16 mm) aggregates, and geometric mean diameter. Slow OS combined with fast RS showed significantly greater air permeability than all other treatments. The results suggest that there is a potential for controlling soil structure in seedbed preparation by minimizing compaction from traffic and adapting site‐specific control of rotovation intensity.     

Effect of tillage treatments on soil thermal conductivity for some Jordanian clay loam and loam soils

Soil thermal conductivity determines how a soil warms or cools with exchange of energy by conduction, convection, and radiation. The ability to monitor soil thermal conductivity is an important tool in managing the soil temperature regime to affect seed germination and crop growth. In this study, the temperature-by-time data was obtained using a single probe device to determine the soil thermal conductivity. The device was used in the field in some Jordanian clay loam and loam soils to estimate their thermal conductivities under three different tillage treatments to a depth of 20 cm. Tillage treatments were: no-tillage, rotary tillage, and chisel tillage. For the same soil type, the results showed that rotary tillage decreased soil thermal conductivity more than chisel tillage, compared to no-tillage plots. For the clay loam, thermal conductivity ranged from 0.33 to 0.72 W m⁻¹ K⁻¹ in chisel plowed treatments, from 0.30 to 0.48 W m⁻¹ K⁻¹ in rotary plowed treatments, and from 0.45 to 0.78 W m⁻¹ K⁻¹ in no-till treatments. For the loam, thermal conductivity ranged from 0.40 to 0.75 W m⁻¹ K⁻¹ in chisel plowed treatments, from 0.34 to 0.57 W m⁻¹ K⁻¹ in rotary plowed treatments, and from 0.50 to 0.79 W m⁻¹ K⁻¹ in no-till treatments. The clay loam generally had lower thermal conductivity than loam in all similar tillage treatments. The thermal conductivity measured in this study for each tillage system, in each soil type, was compared with independent estimates based on standard procedures where soil properties are used to model thermal conductivity. The results of this study showed that thermal conductivity varied with soil texture and tillage treatment used and that differences between the modeled and measured thermal conductivities were very small.     

An approach for draft prediction of combination tillage implements in sandy clay loam soil

A methodology to predict the draft requirements of combination tillage implements in any soil and operating conditions was developed. This methodology required the draft requirements of individual tillage implements in undisturbed soil condition and draft utilization ratio of the rear passive set of combination tillage implement, which is defined as the ratio of the drafts of the rear passive set operating in combination and individually. Laboratory experiments were conducted to measure the draft requirements of a reference tillage tool (single disk), three scale-model individual (moldboard plow, cultivator and disk gang) and two combination (moldboard plow with disk gang and cultivator with disk gang) tillage implements at different depths (5, 7.5 and 10 cm), speeds (1.2, 2.2, 3.2 and 4.2 km/h), wet bulk densities (in the range of 1.27–1.85 g/cm³) and cone index penetration resistance values (in the range of 445–1450 kPa) in soil bin filled with sandy clay loam soil. The average draft utilization ratio of the reference tillage tool obtained were analyzed by both orthogonal and multiple regression techniques to develop the regression equation considering soil properties, operating and tool parameters. The developed draft equation based on the above mentioned methodology was verified with the data obtained for the draft of scale-model and prototype combination tillage implements in the laboratory and field conditions, respectively. It was found that the developed equation predicted the draft of both combination tillage implements within an average absolute variation of 18.0 and 13.5%, respectively.     

Soil microbial community response to controlled-release urea fertilizer under zero tillage and conventional tillage

Soil microorganisms mediate many important biological processes for sustainable agriculture. The effect of a polymer-coated controlled-release urea (CRU, ESN^®) on soil microbial communities was studied at six sites across western Canada from 2004 to 2006. Fertilizer treatments were CRU, urea and an unfertilized control. Timing of fertilizer application (fall vs. spring) was studied in 9 of the 18 site-years (combinations of sites and years). Wheat (Triticum aestivum L.), canola (Brassica napus L.) and barley (Hordeum vulgare L.) were grown in rotation at five sites, and silage corn (Zea mays L.) was grown in all 3 years at one site, under conventional tillage (CT) or zero tillage (ZT). The fertilizers were side-banded at 50–60 kg N ha⁻¹ for wheat, barley and canola, and broadcast at 150 kg N ha⁻¹ for corn. Microbial biomass C (MBC) and bacterial functional diversity and community-level physiological profiles (CLPPs) were determined at about the flowering stage of each crop. In situ CO₂ evolution (soil respiration) was measured, and microbial metabolic quotient (qCO₂) determined, at one site in 2 years. In the rhizosphere, fertilizer effects on MBC and functional diversity were observed in 1 and 5 of 18 site-years, respectively; and in bulk soil in 4 site-years each. These effects were usually positive relative to the control. CRU increased MBC or functional diversity more than urea in 3 site-years, but the opposite was observed in 1 site-year. Time of fertilizer application affected MBC in 1, and functional diversity in 2, of 9 site-years in the rhizosphere, and no effects were observed in bulk soil. Fall-applied fertilizer increased MBC more than spring-applied fertilizer, but the opposite was observed for functional diversity. Tillage affected MBC and functional diversity in 4 and 5 of 18 site-years, respectively, in the rhizosphere, and in 3 and 4 site-years in bulk soil. Tillage effects were usually in favour of ZT. There were no treatment effects on CO₂ evolution, but an interactive effect of fertilizer and tillage on qCO₂ was observed in 1 year when qCO₂ in the control treatment was greater than that in either fertilizer treatment under CT, but urea increased qCO₂ relative to the control under ZT. Shifts in CLPPs were sometimes observed where the treatment effects described above were not significant. Notwithstanding the limitations of culture-dependent CLPPs, most fertilizer effects on soil microbiological properties were not statistically significant. Therefore, these fertilizers probably did not adversely affect most soil biological processes.     

An economic comparison of barley production under zero and conventional tillage

Zero tillage consistently resulted in reduced costs associated with equipment operations, in reduced barley yields, and in higher herbicide costs at all 4 locations. Summation of these major effects indicated that zero tillage on the average was $48.77 ha⁻¹ (range of $18.43–68.79) less economical than conventional tillage. Long-term effects, such as erosion control, changes in soil structure and nutrients, or the indirect consequences of increased herbicide use were not considered in the economic analysis.     

不同耕作方式对中国东北黑土有机碳的短期影响

A tillage experiment, consisting of moldboard plow （MP）, ridge tillage （RT）, and no-tillage （NT）, was performed in a randomized complete block design with four replicates to study the effect of 3-year tillage management on SOC content and its distribution in surface layer （30 cm） of a clay loam soil in northeast China. NT did not lead to significant increase of SOC in topsoil （0-5 cm） compared with MP and RT; however, the SOC content in NT soil was remarkably reduced at a depth of 5-20 cm. Accordingly, short-term （3-year） NT management tended to stratify SOC concentration, but not necessarily increase its storage in the plow layer for the soil.     

Rainfall and tillage effects on soil structure after alfalfa conversion to maize on a clay loam soil in New York

Soil degradation is accelerated when perennial crops are converted to annual row crops, primarily due to increased soil disturbance from tillage. Subsequent heavy rainfall may induce soil settling, reduce macroporosity and increase hardsetting upon drying. An experiment involving plow and no-tillage and two simulated rainfall treatments (‘wet’ and ‘dry’) was conducted on Kingsbury clay loam soil in northern New York in 1992 and 1993 to study their effects on soil structure under maize (Zea mays L.) after conversion from alfalfa (Medicago sativa L.), and to evaluate the use of spectral analysis of micropenetrometer observations for studying soil aggregation. Undisturbed soil cores were collected from the row and trafficked and non-trafficked interrow positions at the 0.05 and 0.15 m depths and used for laboratory measurement of soil strength and pore system properties. These well-structured soils show a high contribution (up to 0.15 m³ m⁻³) of macropores to the total porosity of the soil. Soil strength was generally slightly higher for no-till (NT) than plow till (PT), although only significant in 1992. Soil strength in the surface layer did not change significantly with drying. Spectral density patterns did not show strong treatment effects, although distinct peaks reflect 3.0–3.5 mm stable structural units within macroaggregates. Simulated rainfall treatments and tillage treatments generally did not strongly affect measured soil properties, presumably due to stable soil structure. Structurally stable clay loam soils show little effect of tillage or settling on soil physical properties in the first years after alfalfa to maize conversion, and have good potential for long-term annual crop production if properly managed.     

Phosphorus release during decomposition of crop residues under conventional and zero tillage

Field experiments were conducted at Fort Vermilion (58°23′N 116°02′W), Alberta, to determine phosphorus (P) release patterns from red clover (Trifolium pratense) green manure (GM), field pea (Pisum sativum), canola (Brassica rapa) and monoculture wheat (Triticum aestivum) residues in the 7th and 8th years of conventional and zero tillage. Phosphorus contained in crop residues ranged from 1.5 kg ha⁻¹ in pea to 9.2 kg ha⁻¹ in clover GM, both under zero tillage. The patterns of P release over a 52-week period sometimes varied with tillage, i.e., a greater percentage of GM residue P was released under conventional tillage than under zero tillage in the first 2–10 weeks of residue placement. Wheat residues resulted in net P immobilization under zero tillage, but the amounts immobilized were less than 1 kg ha⁻¹. When net P mineralization occurred, the percentage of P released ranged from 24% of wheat P under conventional tillage to 74% of GM P under conventional tillage. The amounts of P released were 0.4 kg ha⁻¹ from wheat, 0.8 kg ha⁻¹ from canola, 0.4 kg ha⁻¹ from pea and 5.1–5.6 kg ha⁻¹ from clover GM residues. Therefore, only GM residues recycled agronomically significant amounts of P for use by subsequent crops in rotation. Phosphorus release was positively correlated with residue P concentration and negatively correlated with C/P and lignin/P ratios.     

Bacterial diversity in water-stable aggregates of soils under conventional and zero tillage management

Reduced tillage of agricultural soils has been shown to result in greater macroaggregation, microbial biomass and microbial diversity. While it has been shown that macroaggregates contain more microbial biomass per unit soil mass than microaggregates, it is unclear how microbial diversity varies with soil aggregation. We investigated the functional diversity (catabolic potential) of bacteria, evaluated by calculating Shannon’s diversity index (H′), substrate richness (S) and substrate evenness (E) from potential substrate utilization patterns, in whole soil (i.e. not separated into different aggregate sizes) and aggregates of different sizes (2–4, 1–2, 0.5–1, 0.25–0.5, and 0.1–0.25 mm diameter) in loam and silt loam soils grown to barley and managed for 6 years under conventional tillage (CT) or zero tillage (ZT) systems in northern British Columbia. There were no significant tillage effects on bacterial diversity in whole soils. In soil aggregates, H′ and E were significantly higher under CT than under ZT on the loam at barley planting time, with no significant aggregate size effects. However, at barley-heading stage, all diversity indices in both soils were significantly higher under ZT than under CT, and they tended to increase with increasing aggregate size. Cluster analysis and principal component analysis of substrate utilization patterns also revealed differences in bacterial community structures between CT and ZT, but the substrates that were utilized differently between the two tillage systems were not the same between soil types or sampling times. The results during the cropping cycle imply that deterioration of soil structure is probably one factor that explains the adverse effects of soil tillage on soil microbial biomass and diversity.     

Short-term effect of tillage and crop rotation on microbial community structure and enzyme activities of a clay loam soil

A field study was carried out to analyze the short-term (2 years) effect of tillage and crop rotation on microbial community structure and enzyme activities of a clay loam soil. The experimental design was a split-plot arrangement of treatments, consisting of two tillage treatments—ridge tillage (RT) and no-tillage (NT)—in combination with two crop rotation treatments—corn (Zea mays L.) monoculture and a 2-year corn-soybean (Glycine max L.) rotation. Phospholipid fatty acid (PLFA) profiles were used to assess soil microbial community structure. No-tillage resulted in significantly higher total PLFAs compared to the RT treatment, which was accompanied by higher activities of protease, β-glucosaminidase, and β-glucosidase. This suggests a close link between soil microbial communities and enzyme activities in response to tillage. The increase of total microbial lipid biomass in the NT soils was due to the increase in both fungal and bacterial PLFAs. Crop rotation had little effect on soil bacterial communities and enzyme activities, but it significantly influenced soil fungal communities, particularly arbuscular mycorrhizal fungi. Soils under monoculture corn had higher fungal biomass than soils under corn-soybean rotation regardless of tillage treatment.     

Chemical and biochemical properties in a silty loam soil under conventional and organic management

To improve soil fertility, efforts need to be made to increase soil organic matter content. Conventional farming practice generally leads to a reduction of soil organic matter. This study compared inorganic and organic fertilisers in a crop rotation system over two cultivation cycles: first crop broad bean (Vicia faba L.) and second crop mixed cropped melon-water melon (Cucumis melo-Citrullus vulgaris) under semi-arid conditions. Total organic carbon (TOC), Kjeldahl-N, available-P, microbial biomass C (Cmic), and N (Nmic), soil respiration and enzymatic activities (protease, urease, and alkaline phosphatase) were determined in soils between the fourth and sixth year of management comparison. The metabolic quotient (qCO₂), the Cmic/Nmic ratio, and the Cmic/TOC ratio were also calculated. Organic management resulted in significant increases in TOC and Kjeldahl-N, available-P, soil respiration, microbial biomass, and enzymatic activities compared with those found under conventional management. Crop yield was greater from organic than conventional fertilizer. The qCO₂ showed a progressive increase for both treatments during the study, although qCO₂ was greater with conventional than organic fertilizer. In both treatments, an increase in the Cmic/Nmic ratio from first to second crop cycle was observed, indicating a change in the microbial populations. Biochemical properties were positively correlated (p < 0.01) with TOC and nutrient content. These results indicated that organic management positively affected soil organic matter content, thus improving soil quality and productivity.     

Verification of traffic-induced soil compaction after long-term ploughing and 10 years minimum tillage on clay loam soil in South-East Norway

Grain yields are presented from a 10-year field trial with four tillage regimes (annual ploughing, harrowing only, ploughing/harrowing alternate years and minimum tillage) on clay loam. We also present soil physical analyses and use the compaction verification tool (CVT) to assess compaction on plots with annual ploughing and minimum tillage, after using slurry tankers with contrasting wheel loads (4.1 Mg, 6.6 Mg) and wheeling intensities (1×/10×) in the 11th trial year, and yields monitored two years after compaction. Winter wheat yields in the period before compaction were strongly affected by tillage, with annual ploughing giving on average 24% higher yield than direct drilling. Both wheat and oats were far less affected in treatments with harrowing only or ploughing/harrowing alternate years, on average within 6% of annual ploughing. Yields after compaction were affected by both previous tillage and compaction intensity. In the first year, single wheeling after annual ploughing gave 23% yield reduction with 4.1 Mg wheel load and 28% reduction with 6.6 Mg wheel load, whilst multiple wheeling gave 14% reduction at 6.6 Mg wheel load. Yield reductions after minimum tillage ranged from 63% (single wheeling with 4.1 Mg) to 100% (multiple wheeling with 6.6 Mg). Similar trends were found in the second year. The soil physical data indicated that all wheeling led to changes in bulk density, pore sizes and permeability in both topsoil and subsoil on both sampled tillage plots. However, effects in the subsoil were partly masked by the soil's high initial bulk density, partly due to its high clay content. The CVT, which plots air capacity against hydraulic conductivity, suggested some harmful compaction on both plots, with the minimum tillage plot being less affected than the ploughed plot. However, yield results did not support this conclusion, indicating that other factors limited yields on the minimum tilled plot.     

Nitrate leaching losses under Miscanthus grass planted on a silty clay loam soil

Abstract. Nitrate leaching under newly planted Miscanthus grass was measured for three years. The crop received either no fertilizer-N or an annual spring application of 60 kg or 120 kg N ha^-1. During three winters soil water was collected from porous cup probes installed 90 cm deep. Nitrate leaching was calculated from the mean drain flow recorded in two drain gauges multiplied by the mean nitrate-N concentration in the soil water solutions collected. In the first year soil water nitrate concentrations were high on all treatments and N losses were 154, 187 and 228 kg ha^-1 respectively on the unfertilized treatment and those that received 60 or 120 kg N ha^-1. Leaching losses in the second and third years were, in turn, 8, 24 and 87 kg ha^-1 and 3, 11 and 30 kg ha^-1 for the unfertilized treatment and for the 60 and 120 kg N ha^-1 treatments respectively. Leaching losses were closer to those recorded under extensively managed grassland than arable land. The large losses in the first year were probably due to the previous agricultural management at the site and excessive inputs of N on the fertilized plots. In the second and third year, lower drainage volumes may also have influenced losses. The results show that Miscanthus , once established, can lead to low levels of nitrate leaching and improved groundwater quality compared with growing arable crops.     

Relationships between soil macroaggregation and humic carbon in a sandy loam soil following conservation tillage

Purpose

Humic substances are recalcitrant and might act as persistent binding agents to form macroaggregates. The focus of this study is in investigating the contribution of humic carbon (HC) to soil aggregation in response to various tillage and residue managements.

Materials and methods

Arable soils following 8-year contrasting managements were collected to determine aggregate size distribution and stability and HC fractions including humic acid (HA) and fulvic acid (FA). The contribution of HC to aggregation was divided into three special effects including positive effect (PE), negative effect (NE), and combined effect (CE), and these effects were measured using aggregate fractionation techniques.

Results and discussion

As well as to promote structural stability, HC bounds predominantly with the silt + clay fraction and secondarily with microaggregates to form larger aggregates. The PE increased with increasing aggregate size, whereas the NE followed the opposite pattern. A positive CE was observed for large and small macroaggregates, whereas the CE for microaggregates and the silt + clay fraction was negative. Compared to continuous tillage, reduced- and no-tillage decreased the PE for large and small macroaggregates by 1.58–30.98% at the 0–20 cm depth, and straw returning also slightly decreased the corresponding PE relative to straw removing. By contrast, a significantly higher NE for small macroaggregates at the 0–10 cm depth while 6.33–81.11% decreases in CE for large and small macroaggregates at the 0–10 cm depth as well as for large macroaggregates at the 10–20 cm depth, were observed under reduced- and no-tillage. The extraction of HC significantly reduced the aggregate stability and reduced- and no-tillage effectively limited its decrease magnitude. Small macroaggregates and microaggregates made larger contributions to soil HC accumulation than did other fractions. An averagely increased contribution from large or small macroaggregates was observed under both reduced-/no-tillage and straw returning at the 0–20 cm depth. A significant and positive relationship was found between the mass proportion of macroaggregates and the HC accumulation in 0–20 cm soil. Large macroaggregates had significantly higher HA/FA ratios than small macroaggregates, and reduced- and no-tillage significantly increased these ratios both in large and in small macroaggregates. The CE for large or small macroaggregates was also significantly negatively correlated with their HA/FA ratios.

Conclusions

Overall, the HC accumulation in soil is likely to play a key role in macroaggregation, but conservation tillage might decrease the contribution magnitude of HC to large or small macroaggregation through increasing the corresponding HA/FA ratios.

     

Effect of tillage and crop rotations on pore size distribution and soil hydraulic conductivity in sandy clay loam soil of the Indian Himalayas

Tillage management can affect crop growth by altering the pore size distribution, pore geometry and hydraulic properties of soil. In the present communication, the effect of different tillage management viz., conventional tillage (CT), minimum tillage (MT) and zero-tillage (ZT) and different crop rotations viz. [(soybean–wheat (S–W), soybean–lentil (S–L) and soybean–pea (S–P)] on pore size distribution and soil hydraulic conductivities [saturated hydraulic conductivity (K_sat) and unsaturated hydraulic conductivity {k(h)}] of a sandy clay loam soil was studied after 4 years prior to the experiment. Soil cores were collected after 4 year of the experiment at an interval of 75 mm up to 300 mm soil depth for measuring soil bulk density, soil water retention constant (b), pore size distribution, K_sat and k(h). Nine pressure levels (from 2 to 1500 kPa) were used to calculate pore size distribution and k(h). It was observed that b values at all the studied soil depths were higher under ZT than those observed under CT irrespective of the crop rotations. The values of soil bulk density observed under ZT were higher in 0–75 mm soil depth in all the crop rotations. But, among the crop rotations, soils under S–P and S–L rotations showed relatively lower bulk density values than S–W rotation. Average values of the volume fraction of total porosity with pores <7.5 μm in diameter (effective pores for retaining plant available water) were 0.557, 0.636 and 0.628 m³ m⁻³ under CT, MT and ZT; and 0.592, 0.610 and 0.626 m³ m⁻³ under S–W, S–L and S–P, respectively. In contrast, the average values of the volume fraction of total porosity with pores >150 μm in diameter (pores draining freely with gravity) were 0.124, 0.096 and 0.095 m³ m⁻³ under CT, MT and ZT; and 0.110, 0.104 and 0.101 m³ m⁻³ under S–W, S–L and S–P, respectively. Saturated hydraulic conductivity values in all the studied soil depths were significantly greater under ZT than those under CT (range from 300 to 344 mm day⁻¹). The observed k(h) values at 0–75 mm soil depth under ZT were significantly higher than those computed under CT at all the suction levels, except at −10, −100 and −400 kPa suction. Among the crop rotations, S–P rotation recorded significantly higher k(h) values than those under S–W and S–L rotations up to −40 kPa suction. The interaction effects of tillage and crop rotations affecting the k(h) values were found significant at all the soil water suctions. Both S–L and S–P rotations resulted in better soil water retention and transmission properties under ZT.     

Diclofop-methyl dissipation in clay soil under different tillage systems in central Italy

In order to evaluate the effect of simplified tillage systems on herbicide dissipation, diclofop-methyl residues were monitored in different soil layers (0–5 cm, 5–10 cm and 10–30 cm) under three different tillage systems: ploughing 25–30 cm deep (PT), disk harrowing 7–12 cm deep (RT) and no-tillage (NT) in a long-term experiment started in 1990 and carried out on clay soil. Diclofop-methyl residue concentrations in the soil were 0.25 ppm at peak time in topsoil and at lower quantities in the deeper layers. Diclofop-methyl residues in the topsoil were often higher with PT as compared to RT and NT. The presence of diclofop-methyl increased suddenly in untilled plots after a heavy rainfall period. This occurred in the 5–10 cm soil layer 60 days after application, and in the 10–30 cm soil layer 90 days after application. These data suggest a more rapid diclofop-methyl displacement to ground water through macropores under NT conditions.     

Effects of tillage and crop rotation on physical properties of a loam soil

Advances in the development of non-residual herbicides have increased the interest in minimum tillage systems as an alternative to conventional cultivation. This study compared the effects of conventional tillage (CT), minimum tillage (MT) and zero-till (ZT) with continuous winter wheat, winter wheat-summerfallow, and winter wheat-barley-summerfallow on various properties of a Brown Chernozemic loam. Saturated hydraulic conductivity (HC), soil moisture retention, bulk density (BD) and infiltration rate of the soil were measured. The effects of crop rotation by tillage or crop rotation on these soil physical properties were not significant after 8 years of tillage. In general, the BD of the soil under ZT was greater than that under CT in the tillage zone and was lower below the tillage zone. The HC of ZT soil was less than that of CT soil in the tillage zone and greater below the tillage zone. Infiltration rates were not different among the tillage treatments. Although significant differences in some soil properties occurred among tillage treatments, these differences were likely to be too small to affect crop production.