冻融状态和初始含水率对土壤力学性能的影响

冻融状态影响土壤的抗剪强度从而威胁季节性冻土地区的工程安全、边坡稳定以及土壤流失。通过直剪试验测定了不同冻融状态和初始含水率对青藏地区（S1）和北京地区（S2）土体抗剪强度的影响。结果显示,2种土在未冻和已融状态下的抗剪强度相似,且均随着土含水率的增加而减小,但S1土抗剪强度比S2土大7.5%～9.7%;在冻融状态下,S1土抗剪强度随着土含水率的增加而增大,而S2土则随之减小。S1冻融土抗剪强度在低含水率（≤13.5%）时小于未冻土和已融土,而在高含水率（≥24.5%）时则反之;S2冻融土抗剪强度小于未冻土和已融土。在冻融状态下2种测试土的内摩擦角显著小于未冻土和已融土,而黏聚力整体上则大于未冻土和已融土。与未冻土或已融土相比,2种土在冻融状态下的强度相对较低,宜作为季节性冻土地区工程设计以及土壤流失防治的基本状态。     

Assessing the compaction susceptibility of South African forestry soils. II. Soil properties affecting compactibility and compressibility

Factors affecting the compaction susceptibility of South African forestry soils were assessed. Two traditional measures of compaction susceptibility were used: maximum bulk density (ρ_mbd) determined by the standard Proctor test, defined compactibility, and the compression index using a simple uni-axial test, defined compressibility. Soils were chosen from a broad range of geological and climatic regions and they varied greatly in texture (8 to 66 g 100 g⁻¹ clay) and organic matter content (0.26 to 5.77 g 100 g⁻¹ organic carbon). Soils showed a wide range in ρ_mbd values, from 1.24 to 2.00 Mg m⁻³, and this reflected the wide range of particle size distributions and organic matter contents of the soils. Very good correlations were achieved between measures of particle size distribution, particularly clay plus silt and both compactibility and compressibility. Both compactibility and compressibility were significantly correlated with loss-on-ignition (L_OI) which is a measure reflecting the combined effects of soil texture and organic matter on soil physical properties. Indices of compaction susceptibility were influenced more by particle size distribution than by organic carbon content. Clear effects of organic carbon on compaction behaviour were only evident for soils with low clay contents (< 25 g 100 g⁻¹. No clear relationship between compactibility and compressibility was found. Compactibility generally increased with decreasing clay plus silt content, whereas compressibility increased up to about 70 g 100 g⁻¹ clay plus silt before decreasing again. It is difficult to define compaction susceptibility solely in terms of indices of compactibility or compressibility particularly as there is no clear relationship between these two properties. A classification system for compaction risk assessment is presented, based on the relationship between compactibility (ρ_mbd) and L_OI, and between clay plus silt content and compressibility.     

Physical changes and compaction sensitivity of a fine-textured, poorly drained soil (Typic Endoaquept) under varying durations of cropping, Manawatu Region, New Zealand

The physical deterioration of soil under continuous cropping is a problem in many humid, temperate areas. While soils of the Kairanga Series (Typic Endoaquept), Manawatu Region, North Island, New Zealand, are widely used for continuous cereal production, there is concern over the long-term sustainability of this land use. We report the results of a field experiment conducted on a sequence of sites on Kairanga soils, with cropping durations of 0, 4 and 28 years. Study objectives were to quantify physical differences between these soils and to assess a field method for measuring sensitivity to further compaction. Significant changes in key soil physical properties were recorded between the pasture and cropped sites in the 0–30 cm depth range. Most changes had occurred within the first 4 years of cropping. Physical properties that changed significantly included macropore volume (>60 μm), air capacity volume (>30 μm), air permeability, saturated hydraulic conductivity, unsaturated hydraulic conductivity (−0.4 kPa), and shear strength. Bulk density increased significantly only after a long cropping period, and penetration resistance measurements did not significantly differentiate sites of increasing cropping duration. Hence, bulk density and penetration resistance measurements on their own may not be adequate to assess cropping impact. Agricultural tractors were used under moist spring conditions to impose wheel traffic at an intensity of 273–305 Mg km ha⁻¹ on the study sites. The wheel traffic experiment confirmed the trends revealed by the initial site sampling, and also indicated that both soil deformation and soil compaction were the operational forms of soil disturbance at a soil water matric potential of −10 kPa. Soil physical conditions at the long-term cropped site (28 years) had stabilised and were in equilibrium with the soil’s biological and physical environments, while the short-term cropped site (4 years) was still in a transition state, with the likelihood of further increases in bulk density and shear strength. To start appropriate amelioration, it is important to identify when soils are in transition between pasture and long-term cropped states.     

A comparison of five instruments for measuring soil strength in cultivated and uncultivated cereal seedbeds

A torsional shear box, shear vane. cone penetrometer, drop-cone penetrometer and pocket penetrometer were used to measure soil strength at several depths less than 150 mm in cultivated and uncultivated seedbeds in a loam and a sandy clay loam. From the shear box results, cohesion was higher and the angle of friction was lower in the sandy clay loam than in the loam. Angle of friction was independent of cultivation but cohesion was higher in uncultivated than in cultivated soil. Despite these differences cone resistance was similar in both soils above 70 mm depth. Vane shear strength and drop-cone penetration, although empirical, indicated strength differences between soils and cultivations similar to those found with the torsional shear box. Vane shear strength, at 42 kPa, was about twice as high as cohesion in the sandy clay loam and, at 33 kPa, over four times as high as cohesion in the loam. These overestimates increased with increasing bulk density. The range of measurement of the pocket penetrometer was inadequate to cover the range of soil strengths encountered. The coefficient of variation within plots for cone resistance decreased from 76 per cent at 10 mm depth to about 22 per cent at 70 mm depth and below, and for vane shear strength it was 33 per cent near the soil surface. The drop-cone penetrometer results were the most variable, reflecting the log-normal distribution of penetrations. The cone penetrometer was the fastest method, followed by the shear vane, drop-cone penetrometer and torsional shear box in that order.     

Influence of texture on habitable pore space and bacterial-protozoan populations in soil

Summary Soil texture affects pore space, and bacterial and protozoan populations in soil. In the present study we tested the hypothesis that bacteria are more protected from protozoan predation in fine-textured soils than in coarse-textured soils because they have a larger volume of protected pore space available to them. The experiment consisted of three sterilized Orthic Black Chernozemic soils (silty clay, clay loam, and sandy loam) inoculated with bacteria, two treatments (with and without protozoa), and five sampling dates. The soils were amended with glucose and mineral N on day 0. On day 4 bacterial numbers in all three soils were approximately 3×10⁹ g^–1 soil. The greatest reduction in bacteria due to protozoan grazing occurred between day 4 and day 7. Compared to the treatment without protozoa, bacteria in the treatment with protozoa were reduced by 68, 50, and 75% in the silty clay, clay loam, and sandy loam, respectively. On day 4, 2 days after the protozoan inoculation, all protozoa were active. The numbers were 10330, 4760, and 15 380 g^–1 soil for the silty clay, clay loam, and sandy loam, respectively. Between day 4 and day 7, the period of greatest bacterial decline, total protozoa increased greatly to 150480, 96160, and 192100 g^–1 soil for the three soils, respectively. Most protozoa encysted by day 7. In all soils the addition of protozoa significantly increased CO₂–C evolution per g soil relative to the treatment without protozoa. Our results support the hypothesis that bacteria are more protected from protozoan predation in fine-textured soils than in coarse-textured soils.     

Soil carbon and nitrogen sequestration following the conversion of cropland to alfalfa forage land in northwest China

Soil C and N contents play a crucial role in sustaining soil quality and environmental quality. The conversion of annually cultivated land to forage grasses has potential to increase C and N sequestration. The objective of this study was to investigate the short-term changes in soil organic C (SOC) and N pools after annual crops were converted to alfalfa (Medicago sativa L. Algonguin) forage for 4 years. Soil from 24 sets of paired sites, alfalfa field versus adjacent cropland, were sampled at depths of 0–5, 5–10 and 10–20 cm. Total soil organic C and N, particulate organic matter (POM) C and N were determined. Organic C, total N, POM-C, and POM-N contents in the 0–5 cm layer were significantly greater in alfalfa field than in adjacent cropland. However, when the entire 0–20 cm layer was considered, there were significant differences in SOC, POM-C and POM-N but not in total N between alfalfa and crop soils. Also, greater differences in POM-C and POM-N were between the two land-use treatments than in SOC and total N were found. Across all sites, SOC and total N in the 0–20 cm profile averaged 22.1 Mg C ha⁻¹ and 2.3 Mg N ha⁻¹ for alfalfa soils, and 19.8 Mg C ha⁻¹and 2.2 Mg N ha⁻¹ for adjacent crop soils. Estimated C sequestration rate (0–20 cm) following crops to alfalfa conversions averaged 0.57 Mg C ha⁻¹ year⁻¹. Sandy soils have more significant C accumulation than silt loam soils after conversion. The result of this suggests that the soils studied have great C sequestration potential, and the conversion of crops to alfalfa should be widely used to sequester C and improve soil quality in this region.     

Harrowing for weed control: Impacts on mineral nitrogen dynamics, soil aggregation and wheat production

Tillage with a spring tine harrow has become a recommended mechanical weeding technique for cereal crops. In this study, the impact of its use on soil mineral N content, soil aggregation and spring wheat (Triticum aestivum L.) production was investigated. The experiment was performed during 2 successive years (2005–2006) on a clay loam and on a silty loam. The two-main plot treatments consisted of a wheat crop subjected or not to intensive harrow use in a weed-free production system. Two N fertilizer treatments (mineral fertilizer and dry granular poultry manure) were also included as subplots within these main treatments and compared to a non-fertilized control. Harrowing had significant and variable effects on soil NO₃⁻ contents in the 0–5 cm soil layer. Slightly higher NO₃⁻ contents (average difference of 3.2 kg NO₃⁻ ha⁻¹) were measured in the harrowed treatments than in the undisturbed plots in the clay loam soil in 2006. However, significantly lower mineral N contents were observed in the harrowed treatments than in the undisturbed plots in the clay loam soil in 2005 and in the silty loam soil in 2006. This apparent N immobilization amounted to 19 kg NO₃⁻ ha⁻¹ in the clay loam soil in 2005 (for both fertilizers) and 30 kg NO₃⁻ ha⁻¹ in the silty loam soil in 2006 (only in mineral fertilizer plots) after the successive harrowing treatments. In all cases, data of the last sampling dates in the fall indicated that residual NO₃⁻ content was not affected by the treatments. Overall harrowing had a minor decreasing and transient effect on the mean weight diameter (MWD) of soil aggregates while the dry poultry manure tended to increase MWD. The harrowing treatment had no significant effect on wheat, grain N uptake and yield. In conclusion, harrow use had variable impacts on soil NO₃⁻ content and a minor decreasing effect on the MWD of soil aggregates. Of note, significant apparent mineral N immobilization was observed on a few sampling dates following the harrow treatments.     

Shear strength of surface soil as affected by soil bulk density and soil water content

This paper proposes a new method to measure the soil strength parameters at soil surface in order to explain the processes of soil erosion and sealing formation. To simulate the interlocks between aggregates or particles within top 2 mm of the soil, a piece of sandpaper (30 particles cm⁻²) was stuck on the bottom face of a plastic box of diameter of 6.8 cm with stiffening glue and used as shear media. The soil strength for the soils from sandy loam to clayey loam was measured with penetrometer and the new shear device at soil surface at different bulk density and soil water content. The normal stresses of 2, 5, 8, 10 and 20 hPa were applied for the new shear device. The results indicated that significant effect of bulk density on soil strength was detected in most cases though the difference in bulk density was small, ranging from 0.01 to 0.09 g cm⁻³. It was also indicated that the measurement with the new shear device at soil surface was reproducible. The changes in soil shear strength parameters due to changes in bulk density and soil moisture were explainable with the Mohr–Coulomb’s failure equation and the principles of the effective stress for the unsaturated soils. The implications of the method were later discussed.     

Spatial patterns of soil biological and physical properties in a ridge tilled and a ploughed Luvisol

The present study was conducted to determine the spatial heterogeneity of bulk density, soil moisture, inorganic N, microbial biomass C, and microbial biomass N in the ridge tillage system of Turiel compared to conventional mouldboard ploughing on three sampling dates in May, July, and August. The soil sampling was carried out under vegetation representing the ridge in a high spatial resolution down the soil profile. Bulk density increased with depth and ranged from 1.3 g cm⁻³ at 10 cm depth to 1.6 g cm⁻³ at 35 cm in ploughed plots and from 1.0 g m⁻³ at 5 cm to 1.4 g m⁻³ at 35 cm in the ridges. In the ploughed plots, the contents of microbial biomass C and microbial biomass N remained roughly constant at 215 and 33 μg g⁻¹ soil, respectively, throughout the experimental period. The microbial biomass C/N ratio varied in a small range around 6.4. In the ridged plots, the contents of microbial biomass C and microbial biomass N were 5% and 6% higher compared to the ploughed plots. Highest microbial biomass C contents of roughly 300 μg g⁻¹ soil were always measured in the crowns in July. The lowest contents of microbial biomass C of 85–137 μg g⁻¹ soil were measured in the furrows. The ridges showed strong spatial heterogeneity in bulk density, soil water content, inorganic nitrogen and microbial biomass.     

The distribution of volatile isoprenoids in the soil horizons around Pinus halepensis trees

We measured the terpene concentration in pentane and water extracts from soil horizons (litter, organic, top and low mineral) and from roots growing in top and low mineral horizons on a distance gradient from Pinus halepensis L. trees growing alone on a grassland. Terpene concentrations in pentane were higher than in water extracts, although β-caryophyllene showed relatively high solubility in water. The litter and roots were important sources of terpenes in soil. Alpha-pinene dominated in roots growing in both “top” (A1) and “low” (B) mineral horizons (123 ± 36 μg g⁻¹ or 14 ± 5 mg m⁻²) and roots in low mineral horizon (270 ± 91 μg g⁻¹ or 7 ± 2 mg m⁻²). Beta-caryophyllene dominated in litter (1469 ± 331 μg g⁻¹ or 2004 ± 481 mg m⁻²). Terpene concentration in soil decreased with increasing distance to the trunk. This is likely to be related to changes in litter and roots type on the distance gradient from pine to grass and herbs. The relative contributions of all compounds, except α-pinene, were similar in the mineral soils and litter. This suggests that litter of P. halepensis is probably the main source of major terpene compounds. However, long-term emissions of α-pinene from P. halepensis roots might also contribute to α-pinene concentrations in rhizosphere soils.     

冻融条件下土壤侵蚀阻力影响因素

为揭示季节性冻融区土壤侵蚀阻力的变化机制，确定影响土壤侵蚀阻力主控因子，通过室内冻融模拟、水槽冲刷和土壤抗剪试验，对黄绵土(SM粉质壤土)、风沙土(WS砂壤土)和黑土(KS黏壤土)侵蚀阻力影响因素进行研究。结果表明：(1)随着冻融循环次数增加，细沟可蚀性值逐渐升高，而临界剪切力降低。经历10次冻融循环后，SM粉质壤土、WS砂壤土和KS黏壤土的细沟可蚀性分别增加76%,63%,11%,临界剪切力分别减小37%,13%,91%。(2)细沟可蚀性随土壤抗剪强度、黏聚力和内摩擦角增大而减小，临界剪切力则呈相反趋势。与内摩擦角相比，黏聚力更适合用来表征土壤侵蚀阻力。采用黏聚力对SM粉质壤土、WS砂壤土和KS黏壤土的细沟可蚀性进行预测，决定系数(R²)分别为0.42,0.78,0.50,平均为0.57;对临界剪切力的预测效果较差，决定系数(R²)分别为0.16,0.14,0.18,平均仅为0.16。(3)根据皮尔逊相关分析结果，基于土壤的初始含水率、冻融循环次数、力学特性以及土壤参数等分别建立细沟可蚀性(R²=0.85)和临界剪切力...     

土法炼锌区大气沉降Pb、Zn、Cd及其对土壤质量的影响

Dust emissions from smelters, as a major contributor to heavy metal contamination in soils, could severely influence soil quality. Downwind surface soils within 1.5 km of a zinc smelter, which was active for 10 years but ceased in 2000, in Magu Town, Guizhou Province, China were selected to examine Pb, Zn, and Cd concentrations and their fractionation along a distance gradient from a zinc smelter, and to study the possible effects of Pb, Zn, and Cd accumulation on soil microorganisms by comparing with a reference soil located at a downwind distance of 10 km from the zinc smelter. Soils within 1.5 km of the zinc smelter accumulated high levels of heavy metals Zn (508 mg kg-1), Pb (95.6 mg kg-1), and Cd (5.98 mg kg-1) with low ratios of Zn/Cd (59.1--115) and Pb/Cd (12.4--23.4). Composite pollution indices (CPIs) of surface soils (2.52--15.2) were 3 to 13 times higher than the reference soils. In metal accumulated soils, exchangeable plus carbonate-bound fractions accounted for more than 10% of the total Zn, Pb, and Cd. The saturation degree of metals (SDM) in soils within 1.5 km of the smelter (averaging 1.25) was six times higher than that of the reference soils (0.209). A smaller soil microbial biomass was found more frequently in metal accumulated soils (85.1--438 μg C g-1) than in reference soils (497 μg C g-1), and a negative correlation (P < 0.01) of soil microbial biomass carbon to organic carbon ratio (Cmic/Corg) with SDM was observed. Microbial consumption of carbon sources was more rapid in contaminated soils than in reference soils, and a shift in the substrate utilization pattern was apparent and was negatively correlated with SDM (R = -0.773, P < 0.01). Consequently, dust deposited Pb, Zn, and Cd in soils from zinc smelting were readily mobilized, and weredetrimental to soil quality mainly in respect of microbial biomass.     

Suppression of methane oxidation in aerobic soil by nitrogen fertilizers,nitrification inhibitors,and urease inhibitors

Concentrations of CH₄, a potent greenhouse gas, have been increasing in the atmosphere at the rate of 1% per year. The objective of these laboratory studies was to measure the effect of different forms of inorganic N and various N-transformation inhibitors on CH₄ oxidation in soil. NH ₄ ⁺ oxidation was also measured in the presence of the inhibitors to determine whether they had differential activity with respect to CH₄ and NH ₄ ⁺ oxidation. The addition of NH₄Cl at 25 g N g^-1 soil strongly inhibited (78–89%) CH₄ oxidation in the surface layer (0–15 cm) of a fine sandy loam and a sandy clay loam (native shortgrass prairie soils). The nitrification inhibitor nitrapyrin (5 g g^-1 soil) inhibited CH₄ oxidation as effectively as did NH₄Cl in the fine sandy loam (82–89%), but less effectively in the sandy clay loam (52–66%). Acetylene (5 mol mol^-1 in soil headspace) had a strong (76–100%) inhibitory effect on CH₄ consumption in both soils. The phosphoroamide (urease inhibitor) N-(n-butyl) thiophosphoric triamide (NBPT) showed strong inhibition of CH₄ consumption at 25 g g^-1 soil in the fine sandy loam (83%) in the sandy clay loam (60%), but NH ₄ ⁺ oxidation inhibition was weak in both soils (13–17%). The discovery that the urease inhibitor NBPT inhibits CH₄ oxidation was unexpected, and the mechanism involved is unknown.     

Influence of organic matter content, moisture status and time after reworking on soil shear strength

Recovery of soil shear strength was measured in disturbed samples of a calcareous clay loam soils, with four different organic matter contents. Repacked soil cores were put on tension tables at 25 or 50 cm water tension. Shear strength and water content were measured at one of eight time intervals, from 48 h to 7 weeks after the tension was applied. Soil strength increased with increasing organic matter content or increasing the applied tension. The major factor affecting strength, however, was the length of time that tension was applied. Because water contents showed little or no change with time on the tension table these results demonstrate thixotropic recovery of shear strength. This property is discussed with relevance to the soil's potential for mole drainage.     

Rainfall and tillage effects on soil structure after alfalfa conversion to maize on a clay loam soil in New York

Soil degradation is accelerated when perennial crops are converted to annual row crops, primarily due to increased soil disturbance from tillage. Subsequent heavy rainfall may induce soil settling, reduce macroporosity and increase hardsetting upon drying. An experiment involving plow and no-tillage and two simulated rainfall treatments (‘wet’ and ‘dry’) was conducted on Kingsbury clay loam soil in northern New York in 1992 and 1993 to study their effects on soil structure under maize (Zea mays L.) after conversion from alfalfa (Medicago sativa L.), and to evaluate the use of spectral analysis of micropenetrometer observations for studying soil aggregation. Undisturbed soil cores were collected from the row and trafficked and non-trafficked interrow positions at the 0.05 and 0.15 m depths and used for laboratory measurement of soil strength and pore system properties. These well-structured soils show a high contribution (up to 0.15 m³ m⁻³) of macropores to the total porosity of the soil. Soil strength was generally slightly higher for no-till (NT) than plow till (PT), although only significant in 1992. Soil strength in the surface layer did not change significantly with drying. Spectral density patterns did not show strong treatment effects, although distinct peaks reflect 3.0–3.5 mm stable structural units within macroaggregates. Simulated rainfall treatments and tillage treatments generally did not strongly affect measured soil properties, presumably due to stable soil structure. Structurally stable clay loam soils show little effect of tillage or settling on soil physical properties in the first years after alfalfa to maize conversion, and have good potential for long-term annual crop production if properly managed.     

斥水剂作用下非饱和土壤抗剪强度测定及其变化规律

为获得斥水性土壤抗剪强度的变化规律,采用二甲基二氯硅烷(dimethyldichlorosilane,DMDCS)作为斥水剂,获得了不同斥水程度的改性砂土。在此基础上配制了不同斥水剂体质比和不同含水率的改性砂土及不同亲水黏土质量分数的改性混合土,并采用非饱和土直剪仪开展了不固结不排水剪强度试验。结果表明:1)不同DMDCS体质比下的5种改性砂土斥水等级均为极度。改性混合土的斥水等级受DMDCS和黏土含量的共同影响。相同DMDCS体质比下,随着黏土含量的增加,改性混合土的斥水性能不断减弱;相同黏土含量下,随着DMDCS体质比的增加,改性混合土的斥水性能不断增大。2)不同DMDCS体质比、含水率及黏土含量下的改性土壤抗剪强度均可用摩尔-库仑强度准则描述。DMDCS体质比从0增至1%时,黏聚力从19.6陡降至10.4 kPa,随后缓慢降低,最终趋于稳定。内摩擦角则随着DMDCS体质比的增加缓慢减小,从0时的16.2o降至3%时的11.8o;随着含水率的增加,改性砂土黏聚力逐渐减小,而内摩擦角呈先升后降形态;随着黏土含量的增加,改性混合土黏聚力显著增大,内摩擦角表现为先升后降,变幅不大。纯改性砂土的黏聚力仅为9.3 kPa,而掺入5%的黏土时,其黏聚力骤升至27.2 kPa;当黏土质量分数为50%时,混合土黏聚力为55.1 kPa;内摩擦角最大值为16.2°(黏土质量分数15%),最小值为9.7°(黏土质量分数50%)。该成果可为深入研究斥水性土壤力学性能及工程应用提供参考。     

冻融作用对原状棕壤抗剪强度的影响

为揭示冻融循环作用对棕壤抗剪强度的影响,采集沈阳地区5 cm和25 cm 2个深度原状棕壤(分别为H5和H25)为研究对象,通过室内冻融循环模拟和土壤直剪试验,研究冻融循环次数和土壤含水率对土壤抗剪强度的影响.结果表明:(1)土样含水率越高,初次冻融作用的破坏效果越强,1次冻融循环后,含水率为25％的H5和H25土样黏...     

Effects of land-use change on soil microbial C, N and P in a Himalayan watershed

Soil microbial C, N and P as affected by land-use change were studied in a Himalayan watershed at Sikkim, India. The major land-uses considered were forests (dense and open), agroforestry types (large cardamom and mandarin), open cropped and wasteland areas covering subtropical and temperate zones. Across the land-use, microbial C ranged from 219 to 864 μg g⁻¹, microbial N from 30 to 142 μg g⁻¹, and microbial P from 12 to 43 μg g⁻¹ soils. The microbial C, N and P were positively related to each other. The microbial C:N ratio in these soils ranged from 6 to 11 and the microbial C:P ratio from 18 to 27. The conversion of forests into other land-uses resulted in a remarkable decline in the amounts of soil nutrients and microbial C, N and P. The microbial nutrients in the Himalayan region are very sensitive to land-use/cover changes. Therefore, the conversion of forest to agricultural land should be reversed. Agroforestry systems should be included in agricultural land in mountainous regions.     

Effects of seedbed structure and water content at sowing on the development of soil surface crusting under rainfall

This study was carried out to observe the dynamics of crust formation on the soil surface under field conditions and analyse the effects of seedbed structure and water content on soil surface crusting. Seedbed sensitivity to crusting was also estimated in the laboratory by stability tests on aggregates. We observed 57 plots during the sowings of spring and autumn crops in fields in Northern France (Estrees-Mons, 50°N latitude, 3°E longitude). The soil is an Orthic Luvisol according to the FAO classification (0.17–0.25 g g⁻¹ clay and 0.02 g g⁻¹ organic matter on average). Visual assessments in situ were performed and photographs taken of crust stages on delimited areas, each 5 mm of cumulated rainfall since sowing. In 2004–2005, the seedbeds were characterised by their distribution of aggregate sizes and tests of aggregate stabilities of surface samples kept with their water content at sowing. A penetrometer was used to measure crust resistance and estimate its thickness. These data were analysed to detect the cumulative rainfall values needed for the initiation and development of the successive stages of crusts. A fully developed structural crust (stage F1) required 13, 22, 27 mm cumulated rainfall respectively for seedbeds with proportions of clods over 2 cm ranging from 0 to 0.15 (fine seedbed), 0.15 to 0.30 (medium seedbed), >0.30 g g⁻¹ (coarse seedbed). Aggregate stability measured on samples kept at sowing water content was low for soil with low water content (<0.17 g g⁻¹) but increased sharply for water contents over 0.17 g g⁻¹. Stage F1 was reached more rapidly (only 11 mm versus 19 mm cumulated rainfall) only for fine seedbeds with less than 0.15 g g⁻¹ of clods over 2 cm and with a low water content at sowing, The stage of 50% of soil surface covered with sedimentary crusts was reached for 85 mm for fine seedbed versus 120 mm for medium seedbed. The mean penetrometer resistance of dry crusts was 0.55 ± 0.43 MPa for stage F1 and 3.54 ± 0.83 MPa for a sedimentary stage; mean penetrometer resistance increased continuously with cumulated rainfall and was much lower for wet crusts. These quantitative data gathered under field conditions constitute the first step towards the prediction of soil surface crusting. The cumulative rainfalls were used in order to estimate the risk of occurrence of structural and sedimentary crusts forming during crop emergence with several types of seedbeds.     

A nonlinear 3D finite element analysis of the soil forces acting on a disk plow

This study aimed to compare predicted soil forces on a disk plow with measured forces within the tillage depth of clay (90 g kg⁻¹ sand, 210 g kg⁻¹ silt, 700 g kg⁻¹ clay) and sandy loam (770 g kg⁻¹ sand, 40 g kg⁻¹ silt, 190 g kg⁻¹ clay) soils. The model assumed the effects of both tilt angle and plowing speed. Two plowing speeds (4 and 10 km/h) at three tilt angles (15°, 20° and 25°) were compared and the draft, vertical, and side forces determined. A 3D nonlinear finite element model was used to predict the soil forces while a dynamometer was used to measure them on a disk plow in the field. An incremental method was used to deal with material nonlinearity and the Trapezoidal rule method was used to analyze the dynamic response of soil during tillage. Field tillage experiments were conducted to verify the results of the finite element model. It was found that increasing the tilt angle of the plow increased the draft and vertical forces and decreased the side force. Increasing plowing speed increased the draft and side forces and decreased the vertical force. Generally, the results from the finite element model were found to be compatible with the experimental results in clay soil, while in sandy loam the differences between predicted and measured data were probably due to problems of measuring soil mechanical characteristics in the triaxial test.