Mechanical properties of fragrant screwpine fiber reinforced unsaturated polyester composite: Effect of fiber length,fiber treatment and water absorption

Fragrant screwpine fiber reinforced unsaturated polyester composites (FSFRUPC) were subjected to water immersion tests in order to examine the effect of water absorption on the mechanical properties. FSFRUP composite specimen containing 30 % fiber volume fraction with fiber length of 3 mm and 9 mm was considered in this study. Water absorption test was performed by immersing specimen in sea, distilled and well water at room temperature under different time durations (24, 48, 72, 96, 120, 144, 168, 192, 216, 240 hours). The tensile, flexural and impact properties of the water absorption specimen were appraised and compared with those of the dry composite specimen as per the ASTM standard. The tensile, flexural and impact properties of FSFRUPC specimen were found to decrease with the increase in the percentage of moisture uptake. The percentage of moisture uptake of composite was reduced after alkali treatment with 3 % NaoH for 3 hours. In moisture absorption test, the lowest diffusion coefficient, D (6.62513×10^-13 m²/s) and swelling rate parameter, K _sr (6.341×10^-3 h^-1) were obtained through the specimen immersed in sea water. The chemical composition, elemental composition of fiber and surface morphology of the FSFRUPC were analysed by using Fourier transform infrared spectroscopy (FTIR), Energy dispersive spectroscopy (EDS) and scanning electron microscopy (SEM) respectively.     

Woven Kenaf/Kevlar Hybrid Yarn as potential fiber reinforced for anti-ballistic composite material

Woven Kenaf/Kevlar Hybrid Yarn is the combination of natural and synthetic fibers in the form of thread or yarn. The yarn is weaved to form a fabric type of fiber reinforced material. Then, the fabric is fabricated with epoxy as the resin to form a hybrid composite. For composite fabrication, woven fabric Kenaf/Kevlar hybrid yarn composite was prepared with vacuum bagging hand lay-up method. Woven fabric Kenaf/Kevlar hybrid yarn composite was fabricated with total fiber content of 40 % and 60 % of Epoxy as the matrix. The fiber ratios of Kenaf/Kevlar hybrid yarn were varied in weight fraction of 30/70, 50/50 and 70/30 respectively. The composites of woven fabric Kenaf/Epoxy and woven fabric Kevlar/Epoxy were also fabricated for comparison. The mechanical properties of five (5) samples composites were tested accordingly. Result has shown that of value of strength and modulus woven fabric Kenaf/Kevlar Hybrid Yarn composite was increased when the Kevlar fiber content increased. Therefore, among the hybrid composite samples result showed the woven fabric Kenaf/Kevlar Hybrid Yarn composites with the composition of 30/70 ratio has exhibited the highest energy absorption with 148.8 J which 28 % lower than Kevlar 100 % sample. The finding indicated there is a potential combination of natural fiber with synthetic fiber that can be fabricated as the composite material for the application of high performance product.     

Development of mathematical models and estimation for the mechanical properties of organic fiber reinforced polyester composites

Organic fiber from animal waste was used for the development of environmentally friendly animal fiber based polyester composites using cow hair. The cow hair fibers were cut into 10 mm lengths to produce the needed short fiber for random dispersion in the matrix. Before use, some of the fibers were treated with sodium hydroxide for fiber surface modification while some were left as untreated. Composites were developed using predetermined proportions of the fibers in an open mould production process. Samples were formed into tensile and flexural shape in their respective moulds and were stripped off the moulds after curing while further curing was ensured for 27 days before testing. Tensile and flexural properties of the cow hair fiber reinforced polyester composites were evaluated from which it was discovered that the untreated fiber reinforced composites possess better enhancement of mechanical properties compared to the treated fiber reinforced composites and the unreinforced polyester material. Mathematical models for the tensile and flexural properties were developed using statistical packages and estimation using developed software. The developed models revealed high degree of correlation between the experimental values and the predicted values. This denotes that the models can be used to predict the mechanical properties of cow hair reinforced polyester composites for various reinforcement contents.     

Effect of the low and radio frequency oxygen plasma treatment of jute fiber on mechanical properties of jute fiber/polyester composite

We investigated the surface modification of jute fiber by oxygen plasma treatments. Jute fibers were treated in different plasma reactors (radio frequency “RF” and low frequency “LF” plasma reactors) using O₂ for different plasma powers to increase the interface adhesion between jute fiber and polyester matrix. The influence of various plasma reactors on mechanical properties of jute fiber-reinforced polyester composites was reported. Tensile, flexure, short beam shear tests were used to determine the mechanical properties of the composites. The interlaminar shear strength increased from 11.5 MPa for the untreated jute fiber/polyester composite to 19.8 and 26.3 MPa for LF and RF oxygen plasma treated jute fiber/polyester composites, respectively. O₂ plasma treatment also improved the tensile and flexural strengths of jute fiber/ polyester composites for both plasma systems. It is clear that O₂ plasma treatment of jute fibers by using RF plasma system instead of using LF plasma system brings about greater improvement on the mechanical properties of jute/polyester composites.     

Thermal stability and physical properties of epoxy composite reinforced with silane treated basalt fiber

This study evaluates the influence of different silane coupling agents on the thermal and physical properties of epoxy-anhydride composite reinforced with basalt fiber. The silane coupling agents were selected by their functional groups so that they could have different chemical interactions with the epoxy and anhydride curing agents. The thermal and degradation behavior of the composites with different fiber contents were evaluated by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Through the evaluation of T _g and thermal degradation behavior of both systems, it was deduced that the silane coupling agents have a great influence on the thermal properties of the composites as well as interfacial improvement. Also, the tensile properties of the composites were systematically evaluated in order to further understand the effect of silane coupling agents on the interaction with basalt fiber and epoxy matrix.     

Enhancement of the mechanical properties of glass/polyester composites via matrix modification glass/polyester composite siloxane matrix modification

Enhancement of the mechanical and vibrational properties of glass/polyester composites was aimed via matrix modification technique. To achieve this, unsaturated polyester was modified by incorporation of oligomeric siloxane in the concentration range of 1–3 wt%. Modified matrix composites reinforced with woven roving glass fabric were compared with untreated glass/polyester in terms of mechanical and interlaminar properties by conducting tensile, flexure, and short-beam shear tests. It was found that after incorporation of 3 % oligomeric siloxane into the polyester matrix, the tensile, flexural, and interlaminar shear strength (ILSS) values of the resulting composite increased by 16, 15, and 75 %, respectively. The increases in ILSS as well as in tensile and flexural properties were considered to be an indication of better fiber/matrix interaction as confirmed by SEM fractography images. Furthermore, the effect of oligomeric siloxane incorporation on the vibrational properties of the composites was investigated by experimental modal testing and the natural frequencies of the composites were found to increase with increasing siloxane concentration.     

Experimental investigation of mechanical behavior of Jute-Flax based glass fiber reinforced composite

Present technological development and innovation needs a better class of material that meets all the practical applications along with its environmental friendly nature and economical value. Hybrid natural fiber composites, a sector of natural composites meets these requirements. This paper deals with fabrication, mechanical characterization of a hybrid (Jute+Flax+GFRP) composite and also the comparison of it with the (Jute+GFRP) based composite. These composites are fabricated using hand lay-up technique. The arrangement of hybrid composite is such that a layer of vertically laid flax fiber is flanked between layers of horizontally laid jute fiber. Epoxy resin alongside with HY951 hardener is used as the binding agent throughout the layer. Glass fiber laminates are used on both sides for improving the surface finish and surface hardness. The volumetric fraction is such that one third of total volume is occupied by Jute and Flax fibers. Test results shows that the hybrid natural composite has excellent properties under tensile, flexural loading. At last failure morphology analysis is done using Scanning Electron Microscope (SEM) and the internal structure of the broken specimen is discussed.     

Mechanical properties and water absorption of short snake grass fiber reinforced isophthallic polyester composites

Natural fiber composite replaces the conventional and synthetic materials in many fields especially in light weight applications. The randomly oriented short snake grass fiber reinforced isophthallic polyester composites are prepared by hand lay-up technique and finally compression molded. The various length and weight fraction of fiber are used in composite fabrication. The mechanical properties and water absorption under various climatic conditions are examined according to the prescribed standard. SEM image revealing the fiber pullout and breakage of the tensile and impact fractured composite specimens has been analysed and compared with control through scanning electron microscope. The result shows that the mechanical properties increase with increase in fiber length and weight fraction of the composites. The rate of water absorption increases with increase in temperature and time. Obtained experimental tensile strength of the composite is compared with various theoretical models such as Series, Hirsch’s, Halpin-Tsai, Modified Halpin-Tsai and Modified Bowyer & Brader’s and the obtained inferences are discussed.     

Improvement in mechanical properties of aluminum polypropylene composite fiber

Aluminum particles (Al) were added to polypropylene (PP) in the presence of poly ethylene glycol (PEG) and polypropylene-graft-maleic anhydride to produce composites. The composites were then melt-spun into a mono filament and tested for tensile properties, diameter evenness and morphology. Melt rheological properties of Al/PP composites were studied in linear viscoelastic response regions. It was observed that level of dispersion of aluminum particles within a polypropylene composite fiber could be improved by incorporating polyethylene glycol. The improvement of dispersion led to an improvement in the fibers mechanical properties through a reduction of the coefficient of variation of fiber diameter.     

Enhancement of thermal and physical properties of epoxy composite reinforced with basalt fiber

The basalt chopped fiber reinforced epoxy composites using different curing systems were prepared in order to investigate the thermal characteristics of the composites. 2 different curing systems for bisphenol F type epoxy resin — an epoxy-amine curing system and an epoxy-anhydride curing system — were selected and used to investigate the interaction between matrix resin and basalt fiber in the means of thermal properties and physical properties. Through the evaluation of T _g and thermal degradation behavior of both systems, it was deduced that the type of curing system as well as basalt fiber reinforcement have a great role in determining thermal properties of the composites. Also, the tensile and flexural properties of the composites were systematically evaluated in order to further understand the effect of curing agents on the interaction with basalt fiber.     

Effect of hollow polyester fibres on mechanical properties of knitted wool/polyester fabrics

The physical and mechanical characteristics of hollow polyester fibres were compared with solid polyester fibres in order to establish their processing behaviour and performance characteristics. The effects of hollow fibres on fabric properties were investigated by using microscopy and tests of tensile and bursting strength, pilling, abrasion resistance, water vapour permeability, and handle. The results show that tensile strength of hollow polyester fibres and yarns are negatively affected by the cavity inside the fibre. Hollow fibres also have higher stiffness and resistance to bending at relaxed state. Fabrics made from hollow polyester/wool blends and pure wool fabrics show three distinguishable steps in pilling. During pilling, hollow fibres break before being pulled fully out of the structure, leading to shorter protruding fibres. Microscopy studies showed that the breakdown of hollow fibres started during entanglement by splitting along the helical lines between fibrils. KES results showed that the friction between fibres and the fibre shape are the most important parameters that determine the fabric low stress mechanical properties. However, in some aspects, the hollow structure of the fibre does not have a significant effect.     

Fabrication of long and discontinuous natural fiber reinforced polypropylene biocomposites and their mechanical properties

Natural fiber reinforced polypropylene (PP) biocomposites were fabricated by blending long-and-discontinuous (LD) natural fibers (NF) with LD PP fibers. Firstly, random fiber mats were prepared by mixing NFs and PP fibers using a carding process. Then, heat and pressure were applied to the mats, such that the PP fibers dispersed in the mats melted and flowed out, resulting in the formation of consolidated sheets upon subsequent cooling. The effect of the fiber volume fraction on the mechanical properties of the bio-composites was scrutinized by carrying out tensile and flexural tests and observing the interface between the fiber and matrix. It was observed that the natural LD fiber content needs to be maintained at less than the nominal fiber fraction of 40 % by weight for the composites fabricated using the current method, which is quite low compared to that of continuous or short fiber reinforced composites. The limited fiber fraction can be explained by the void content in the biocomposites, which may be caused by the non-uniform packing or the deficiency of the matrix PP fibers.     

Investigations on mechanical characteristics of glass fiber reinforced epoxy composite modified with amino-terminated hyperbranched polymer

Glass fiber, GF, which was first hydroxylated and silanized, was incorporated into epoxy resin modified with amino-terminated hyperbranched polymer (ATHBP) to obtain high performance composite. The effects of GFs content on the mechanical properties of composites were investigated, discussing the results from flexural, tensile, and impact tests. The composites revealed noticeable improvement in flexural strength, tensile strength as well as impact strength but slow decrease in elongation at break, compared to the epoxy/ATHBP thermoset. FESEM morphology results indicated the good compatibility between epoxy matrix and GF in the appearance of ATHBP and showed that the toughening mechanism was mainly attributed to the stress transfer mechanism.     

Thermal characteristics of basalt fiber reinforced epoxy-benzoxazine composites

This study investigates the possibility of utilizing basalt chopped fiber in order to prepare a thermally stable fiber reinforced composite. Bi-component resin system using epoxy and benzoxazine monomer is proposed and its cure characteristic is evaluated by FT-IR and DSC. Copolymerization of epoxy resin upon curing with benzoxazine is carried out in the absence of a strong catalyst. Through the evaluation of T _g of the epoxy-benzoxazine copolymer resin and its composite, it is clear that the incorporation of basalt fiber in composite has a great role and advantage. Also, this study systematically evaluates the apparent char yield and net char yield gain of the composites using TGA thermograms. Based on the results of DSC and TGA, it is advised that the favorable composite composition can be prepared from the range of 20 % to 50 % of epoxy content with 10 % of basalt fiber.     

Thermal and mechanical properties of polypropylene filaments reinforced with multiwalled carbon nanotubes via melt compounding

This study examined the thermal and mechanical properties of polypropylene filaments reinforced with multi-walled carbon nanotubes (MWNTs). The MWNTs were functionalized with maleic anhydride polypropylene to increase the interfacial interactions between the CNTs and polypropylene. PP/MWNT composites with different concentrations of MWNTs were prepared by melt compounding using a twin screw extruder. The composites of the filament were then post drawn and heat treated. Tensile tests showed increased strength with the addition of only 0.1 wt% while there were only slight changes in elongation. The thermal properties were also slightly enhanced by the MWNTs.     

Effect of fiber length on mechanical behavior of coir fiber reinforced epoxy composites

Fiber reinforced polymer composites have played a dominant role for a long time in a variety of applications for their high specific strength and modulus. The fiber which serves as a reinforcement in reinforced plastics may be synthetic or natural. To this end, an investigation has been carried out to make use of coir, a natural fiber abundantly available in India. Natural fibers are not only strong and lightweight but also relatively very cheap. The present work describes the development and characterization of a new set of natural fiber based polymer composites consisting of coconut coir as reinforcement and epoxy resin as matrix material. The developed composites are characterized with respect to their mechanical characteristics. Experiments are carried out to study the effect of fiber length on mechanical behavior of these epoxy based polymer composites. Finally, the scanning electron microscope (SEM) of fractured surfaces has been done to study their surface morphology.     

Compressive and flexural properties of hemp fiber reinforced concrete

The compressive and flexural properties of hemp fiber reinforced concretes (FRC) were examined in this paper. Natural hemp fiber was mixed using dry and wet mixing methods to fabricate the FRC. Mechanical properties of the FRC were investigated. The main factors affecting compressive and flexural properties of the FRC materials were evaluated with an orthogonal test design. Fiber content by weight has the largest effect. The method for casting hemp FRC has been optimised. Under the optimum conditions, compressive strength increased by 4 %, flexural strength increased by 9 %, flexural toughness increased by 144 %, and flexural toughness index increased by 214 %.     

Evaluation of mechanical properties of jute/glass/carbon fibers reinforced hybrid composites

A study on the tensile and flexural properties of jute-glass-carbon fibers reinforced epoxy hybrid composites in inter-ply configuration is presented in this paper. Test specimens were manufactured by hand lay-up process and their tensile and flexural properties were obtained. The effects of the hybridization, different fibers content and plies stacking sequence on the mechanical properties of the tested hybrid composites were investigated. Two-parameter Weibull distribution function was used to statistically analyze the experimental results. The failure probability graphs for the tested composites were drawn. These graphs are important tools for helping the designers to understand and choose the suitable material for the required design and development. Results showed that the hybridization process can potentially improve the tensile and flexural properties of jute reinforced composite. The flexural strength decreases when partial laminas from a carbon/epoxy laminate are replaced by glass/epoxy or jute/epoxy laminas. Also, it is realized that incorporating high strength fibers to the outer layers of the composite leads to higher flexural resistance, whilst the order of the layers doesn’t affect the tensile properties.     

Study on mechanical and thermal properties of fiber-reinforced Epoxy/Hybrid-silica composite

Recently, carbon fiber composites have been widely used as structural reinforcement materials of buildings, replacing reinforcing bars or concrete. And the increase in use of super fibers such as aramid and high strength PE, which is aimed at improving the reinforcement properties, has resulted in a demand for a resin system with excellent mechanical and thermal properties. In this research, a fiber-reinforced composite has been produced by using the super fibers such as carbon fiber or aramid fiber, reinforcement resin and the silica hybrid compound containing epoxy group. This study was carried out to confirm the effect of the silica hybrid on mechanical properties, heat resistance and adhesion strength of a fiber-reinforced epoxy composite, which was produced by blending silica or introducing silica hybrid through covalent bonds. And the silica hybrid containing epoxy group, which may be introduced to the structure of fiber-reinforced epoxy composite through covalent bonds caused by reaction with a hardener, has been used, so that the heat resistance and adhesion strength could be improved.     

Shear modeling of fiber reinforced soil composite on the base of fiber pull-out test

The concept of reinforcing soil with natural fibers was originated in ancient times. However, short natural and synthetic fiber soil composites have recently attracted increasing attention in geotechnical engineering for the second time. Consequently in this work, shear behavior of fiber reinforced soil composite was modeled by using force-equilibrium method. The proposed model indicated that fiber percentage, fiber diameter, fiber aspect ratio, Elastic Modulus of fiber, coefficient of friction between fiber and matrix, the thickness of shearing zone and vertical compressive stress determine the shear resistance of a fiber reinforced soil composite. In the next step, a set of laboratory direct shear tests was performed on different samples including both neat soil and fiber reinforced treatments. In order to compare model outputs and experimental results, it was necessary to measure the coefficient of friction between fiber and soil. Therefore, a novel apparatus based on fiber pull-out test was designed to determine the interfacial shear stress between fiber and soil. Since, soil considers as a soft material and its mechanical properties depend on vertical stress, therefore, the Instron Tensile Tester was modified to provide fiber pull-out test through the soil matrix. Consequently, the proposed model adequately predicted shear behavior of fiber reinforced soil composite based on fiber pull-out test results.