Quantitative characterization of a hardwood milled wood lignin by nuclear magnetic resonance spectroscopy

The structure of Eucalyptus grandis milled wood lignin (MWL) was investigated by 2D 1H-13C HSQC, HMQC, and 1H-1H TOCSY correlation NMR techniques and by quantitative 13C NMR as well as by the permanganate oxidation degradation technique. The combination of 2D NMR and quantitative 13C NMR spectroscopy of nonacetylated and acetylated lignin preparations allowed reliable identification and calculation of the amount of different lignin structures. About 85% of side-chain moieties were estimated on the structural level. This information was substantiated by data on the quantity of various functional groups and interunit linkages as a whole. A modified method for calculation of the h:g:s ratio has been suggested and compared with previously suggested approaches. E. grandis MWL has been determined to have an h:g:s ratio of 2:36:62. The amounts of various phenolic/etherified noncondensed/condensed guaiacyl and syringyl moieties were approximately estimated. E. grandis MWL contained approximately 0.60/Ar of beta-O-4 moieties along with small amounts of other structural units such as pino/syringyresinol (0.03/Ar), phenylcoumaran (0.03/Ar), and spirodienone (0.05/Ar). The degree of condensation was estimated at approximately 21%; the main condensed structures are 4-O-5 moieties (approximately 0.09/Ar). The structure of E. grandis MWL was compared with those of other lignin preparations isolated from various hardwoods.     

Characterization of milled wood lignin (MWL) in Loblolly pine stem wood, residue, and bark

Milled wood lignin samples from Loblolly pine stem wood, forest residue, and bark were isolated and characterized by quantitative (13)C and (31)P nuclear magnetic resonance (NMR), Fourier transform infrared spectroscopy (FT-IR), and gel permeation chromatography (GPC) for molecular weight determination. Results from (13)C NMR show the stem wood and forest residue samples have similar functional group contents. However, the bark has fewer methoxyl groups, β-O-4 structures, dibenzodioxocin, and side chains than the other two lignins. The bark lignin has the highest amounts of p-hydroxyphenyl (h) and C-5 condensed lignin, stem wood has the lowest, and the residue lies between. (31)P NMR analysis indicates that bark lignin contains more C-5 substituted phenolics and fewer aliphatic hydroxyl groups than the lignin isolated from stem wood or residue. The molecular weight distribution analysis indicates the bark lignin has higher weight-average molecular weight (M(w)) and polydispersity index than the lignin recovered from stem wood or residue.     

Comparative evaluation of three lignin isolation protocols for various wood species

Milled wood lignin (MWL), cellulolytic enzyme lignin (CEL), and enzymatic mild acidolysis lignin (EMAL) were isolated from different wood species and characterized by various techniques. The EMAL protocol offered gravimetric lignin yields 2-5 times greater than those of the corresponding MWL and CEL. The purities of the EMALs were 3.75-10.6% higher than those of their corresponding CELs, depending upon the wood species from which they were isolated. Molecular weight analyses showed that the EMAL protocol isolates lignin fractions that are not accessed by the other procedures evaluated, while 31P NMR spectroscopy revealed that MWL is more condensed and bears more phenolic hydroxyl groups than EMAL and CEL. The yields and purities of EMAL, MWL, and CEL from hardwood were greater than those obtained for the examined softwoods. Structural details obtained by DFRC (derivatization followed by reductive cleavage)/31P NMR revealed different contents of condensed and uncondensed beta-O-aryl ether structures, dibenzodioxocins, and condensed and uncondensed phenolic hydroxyl and carboxylic acid groups within lignins isolated from different wood species.     

Structural characterization of lignin from leaf sheaths of "dwarf cavendish" banana plant

Dioxane lignin (DL) isolated from leaf sheaths of banana plant (Musa acuminata Colla var. cavendish) and in situ lignin were submitted to a comprehensive structural characterization employing spectroscopic (UV, FTIR, solid state 13C CP-MAS NMR, liquid state 13C and 1H NMR) and chemical degradation techniques (permanganate and nitrobenzene oxidation). Results obtained showed that banana plant leaf sheath lignin is of HGS type with a molar proportion of p-hydroxyphenyl (H)/guaiacyl (G)/syringyl (S) units of 12:25:63. Most of the H units in DL are terminal phenolic coumarates linked to other lignin substructures by benzyl and Cgamma-ester bonds in contrast to ferulates that are mainly ether linked to bulk lignin. It is proposed that banana plant leaf sheath lignin is chemically bonded to suberin-like components of cell tissues by ester linkages via essentially hydroxycinnamic acid residues. beta-O-4 structures (0.31/C6), the most abundant in DL, comprise mainly S units, whereas a significant proportion of G units is bonded by beta-5, 5-5', and 4-O-5' linkages contributing to ca. 80% of condensed structures in DL.     

Comprehensive study on the chemical structure of dioxane lignin from plantation Eucalyptus globulus wood

Results of a comprehensive study on the chemical structure of lignin from plantation Eucalyptus globulus Labill are presented. Lignin has been isolated by a modified mild acidolysis method and thoroughly characterized by functional group analysis, by a series of degradation techniques (nitrobenzene oxidation, permanganate oxidation, thioacidolysis, and Py-GC-MS), and (1)H and (13)C NMR spectroscopy. Plantation Eucalyptus globulus lignin was found to be of the S/G type with an extremely high proportion of syringyl (S) units (82-86%) and a minor proportion of p-hydrophenyl propane (H) units (roughly 2-3 mol %). Unknown C-6 substituted and 4-O-5' type syringyl substructures represent about 65% of lignin "condensed" structures. Eucalypt lignin showed high abundance of beta-O-4 (0.56/C(6)) structures and units linked by alpha-O-4 bonds (0.23/C(6)). The proportion of phenylcoumaran structures was relatively low (0.03/C(6)). Different kinds of beta-beta substructures (pino-/syringaresinol and isotaxiresinol types) in a total amount of 0.13/C(6) were detected. ESI-MS analysis revealed a wide molecular weight distribution of lignin with the center of gravity of mass distribution around 2500 u.     

Structural characterization of lignin from triploid of Populus tomentosa Carr

To improve yields while minimizing the extent of mechanical action (just 2 h of planetary ball-milling), the residual wood meal obtained from extraction of milled wood lignin (MWL) was sequentially treated with cellulolytic enzyme and alkali, and the yields of MWL, cellulolytic enzyme lignin (CEL), and alkaline lignin (AL) were 5.4, 23.2, and 16.3%, respectively. The chemical structures of the lignin fractions obtained were characterized by carbohydrate analysis, gel permeation chromatography (GPC), Fourier transform infrared (FT-IR) spectroscopy, and various advanced NMR spectroscopic techniques. The results showed that the lignin isolated as MWL during the early part of ball milling may originate mainly from the middle lamella. This lignin fraction was less degradable and contained more linear hemicelluloses and more C═O in unconjugated groups as well as more phenolic OH groups. Both 1D and 2D NMR spectra analyses confirmed that the lignin in triploid of Populus tomentosa Carr. is GSH-type and partially acylated at the γ-carbon of the side chain. Two-dimensional heteronuclear single-quantum coherence (13C-1H) NMR of MWL, CEL, and AL showed a predominance of β-O-4' aryl ether linkages (81.1-84.5% of total side chains), followed by β-β' resinol-type linkages (12.2-16.4%), and lower amounts of β-5' phenylcoumaran (2.1-2.6%) and β-1' spirodienone-type (0.4-1.4%) linkages. The syringyl (S)/guaiacyl (G) ratios were estimated to be 1.43, 2.29, and 2.83 for MWL, CEL, and AL, respectively.     

Toward a better understanding of the lignin isolation process from wood

The recently developed protocol for isolating enzymatic mild acidolysis lignins (EMAL) coupled with the novel combination of derivatization followed by reductive cleavage (DFRC) and quantitative (31)P NMR spectroscopy were used to better understand the lignin isolation process from wood. The EMAL protocol is shown to offer access at lignin samples that are more representative of the overall lignin present in milled wood. The combination of DFRC/(31)P NMR provided a detailed picture on the effects of the isolation conditions on the lignin structure. More specifically, we have used vibratory and ball milling as the two methods of wood pulverization and have compared their effects on the lignin structures and molecular weights. Vibratory-milling conditions cause substantial lignin depolymerization. Lignin depolymerization occurs via the cleavage of uncondensed beta-aryl ether linkages, while condensed beta-aryl ethers and dibenzodioxocins were found to be resistant to such mechanical action. Condensation and side chain oxidations were induced mechanochemically under vibratory-milling conditions as evidenced by the increased amounts of condensed phenolic hydroxyl and carboxylic acid groups. Alternatively, the mild mechanical treatment offered by ball milling was found not to affect the isolated lignin macromolecular structure. However, the overall lignin yields were found to be compromised when the mechanical action was less intense, necessitating longer milling times under ball-milling conditions. As compared to other lignin preparations isolated from the same batch of milled wood, the yield of EMAL was about four times greater than the corresponding milled wood lignin (MWL) and about two times greater as compared to cellulolytic enzyme lignin (CEL). Molecular weight distribution analyses also pointed out that the EMAL protocol allows the isolation of lignin fractions that are not accessed by any other lignin isolation procedures.     

Effects of increased nitrogen supply on the lignification of poplar wood

The short-term influence of adequate and high nitrogen fertilization on poplar lignification was investigated. The high nitrogen supply decreased lignin staining in the newly formed secondary xylem, indicating that lignin deposition was affected. Acetyl bromide determinations gave a 9-10% decrease in lignin content; however, Klason lignin content was unchanged. Thioacidolysis showed that elevated N supply affected lignin structure such that there was a reduced frequency of lignin units involved in beta-O-4 bonds, a reduced syringyl/guaiacyl ratio, an increased frequency of p-hydroxyphenyl lignin units, more guaiacyl units with free phenolic groups, and more p-hydroxybenzoic acid ester-linked to poplar lignins. These features suggest that lignins from poplars grown under high N bear structural similarities to lignins formed during early stages of wood development. The findings also indicate that a gravitational stimulus inducing the formation of tension wood and high N availability lead to similar and additive effects on lignin content and structure.     

Structural characterization of the lignin from the nodes and internodes of Arundo donax reed

Milled wood lignin (MWL) and dioxane lignin (DL) from different morphological regions (nodes and internodes) of Arundo donax reed were subjected to a comprehensive structural characterization by (13)C, (1)H NMR, FTIR, and UV spectroscopies and functional analysis. The permanganate and nitrobenzene oxidation methods were also applied to the in situ lignins. Both node and internode lignins are HGS-type lignins, with a significant amount of H units (including p-coumaric acid type structures). The S/G ratio (1.13-1.32), the weight-average molecular weight (20,400-24,500), the methoxyl group content (0.90-0.98), the phenolic hydroxyl group content (0.23-0.27), and the aliphatic hydroxyl group content (1.00-1.09) are not very different in the lignins from nodes and internodes. However, some structural differences between node and internode lignins were observed. The former has much more phenolic acids (p-coumaric and ferulic), 8.8% in node versus 1.2% in internode and less beta-O-4 (0. 32 and 0.49 per aromatic unit in node and internode, respectively). In situ node lignin is more condensed than internode lignin.     

Elucidation of lignin structure through degradative methods: comparison of modified DFRC and thioacidolysis

Milled wood and milled wood lignin (MWL) samples were subjected to DFRC and thioacidolysis. Despite the fact that both methods selectively cleave aryl ether bonds, substantial differences in results were obtained. Lignin thioacidolysis gave total molar yields of degradation monomer products in the range of 3.5-7 mol % higher than DFRC. GPC analysis showed that the thioacidolysis-treated lignin was degraded to a lower average molecular weight than that treated by DFRC. Contrary to results reported for lignin model compounds, these results indicate that the DFRC method does not completely or efficiently degrade the lignin polymer. In fact, the DFRC-degraded lignin retained much of the characteristics of the original MWL. Elemental analysis revealed the presence of bromine in the DFRC-treated lignin, and two-dimensional (1)H-(13)C HMQC NMR spectroscopy showed the presence of beta-O-4 linkages in the DFRC-treated lignin. No beta-O-4 interunit linkages were detected in the thioacidolysis-treated lignin. These results are consistent with the lower monomer yields and the higher average molecular weight of the DFRC-treated lignin and indicate inefficiency in the chemistry of the method, probably due to steric constraints of the polymeric nature of lignin.     

Abundance and reactivity of dibenzodioxocins in softwood lignin

To define the abundance and comprehend the reactivity of dibenzodioxocins in lignin, model compound studies, specific degradation experiments on milled wood lignin, and molecular modeling calculations have been performed. Quantitative (31)P NMR measurements of the increase of biphenolic hydroxyl groups formed after a series of alkaline degradations in the presence of hydrosulfide anions (kraft conditions) showed the presence of 3.7 dibenzodioxocin rings/100 C9 units in milled wood lignin. The DFRC degradation protocol (Derivatization Followed by Reductive Cleavage) was chosen as an independent means to estimate their abundance. Initial experiments with a dibenzodioxocin model compound, trans-6,7-dihydro-7-(4-hydroxy-3-methoxyphenyl)-4,9-dimethoxy-2,11-dipropyldibenzo[e,g][1,4]dioxocin-6-ylmethanol, showed that it is not cleaved under DFRC conditions, but rather it isomerizes into a cyclic oxepine structure. Steric effects precluded this isomerization from occurring when DFRC was applied to milled wood lignin. Instead, monoacetylated biphenolic moieties were released and quantified by (31)P NMR, at 4.3 dibenzodioxocin rings/100 C9 units. The dibenzodioxocin content in residual lignins isolated from kraft pulps delignified to various degrees showed that during pulp delignification, the initial rate of dibenzodioxocin removal was considerably greater than the cleavage rate of arylglycerol-beta-aryl ether bonds. The activation energy for the degradation of dibenzodioxocins under kraft conditions in milled wood lignin was 96 +/- 9 kJ/mol, similar to that of arylglycerol-beta-aryl ether bond cleavage.     

Lignin structural variation in hardwood species

A comprehensive lignin structure analysis of ten industrially relevant hardwood species is presented. Milled wood lignin (MWL) was isolated from each species using a modified protocol and all milled wood lignin preparations were analyzed through quantitative (13)C NMR spectroscopy, elemental analysis, methoxyl analysis, sugar analysis, and nitrobenzene oxidation. Nitrobenzene oxidation and ozonation were carried out on extractive-free wood, alkali-extracted wood, milled wood lignin, and alkali-extracted lignin. Milled wood lignin isolated by the modified protocol was found to be representative of the total lignin in alkali-extracted wood. Significant variations in lignin structures, such as syringylpropane/guaiacylpropane ratio (S/G ratio), arylglycerol-β-aryl ether (β-O-4), degree of condensation, and elemental and methoxyl contents, were found among the hardwood species studied. These structural variations among species appear to be correlated to a single factor, the syringyl/guaiacyl ratio. A new method to predict the S/G ratio of total lignin in wood was developed, using a calibration line established by the syringaldehyde/vanillin (S/V) ratio (nitrobenzene oxidation) and the S/G ratio ((13)C NMR) of milled wood lignin (MWL).     

Structural characterization of guaiacyl-rich lignins in flax (Linum usitatissimum) fibers and shives

The structural characteristics of the lignins from flax (Linum usitatissimum) fibers and shives were studied. Significant differences in the content and composition of the lignin from both parts were observed. The lignin contents were 3.8% in the fibers and 29.0% in the shives. Analysis by Py-GC/MS indicated a H:G:S molar ratio of 13:72:15 in the milled wood lignin (MWL) isolated from flax fibers and a molar ratio of 5:87:8 in the MWL isolated from flax shives. In addition, 2D-NMR showed a predominance of β-O-4' aryl ether linkages, followed by β-5' phenylcoumaran and β-β' resinol-type linkages in both MWLs, with a higher content of condensed linkages in flax shives. Thioacidolysis (followed by Raney nickel desulfurization) gave further information on the lignin units involved in the different linkages and confirmed the enrichment of G units. The thioacidolysis dimers released were similar from both lignins, with a predominance of the β-5' followed by β-1' and 5-5' structures.     

Inhomogeneities in the chemical structure of sugarcane bagasse lignin

Sequential treatments of dewaxed bagasse with distilled water, 0.5 M NaOH, 0.5, 1.0, 1.5, 2.0, and 3.0% H(2)O(2) at pH 11.5, and 2 M NaOH at 55 degrees C for 2 h solubilized 2.8, 52.5, 14.9, 3.3, 5.5, 5.0, 2.8, and 2.2% of the original lignin, respectively. The eight isolated lignin fractions were subjected to a comprehensive structural characterization by UV, FT-IR, and (1)H and (13)C NMR spectroscopies and thermal analysis. The nitrobenzene oxidation method was also applied to the in situ lignins. The seven lignin fractions, isolated successively with alkali and alkaline peroxide, were all SGH-type lignins, with a small amount of esterified p-coumaric acid and mainly etherified ferulic acid. No significant differences were found in the weight-average molecular weights (1680-2220 g/mol) of the seven alkali and alkaline peroxide dissolved lignins. However, the first four lignin fractions, isolated with 0.5 M NaOH and 0.5, 1.0, and 1.5% H(2)O(2) at pH 11.5, were rich in syringyl units and contained large amounts of noncondensed ether structures, whereas the last three lignin fractions, isolated sequentially with 2.0 and 3.0% H(2)O(2) at pH 11.5 and 2 M NaOH at 55 degrees C for 2 h, had a higher degree on condensation and were rich in guaiacyl lignins.     

Pyrolysis of lignin in the presence of tetramethylammonium hydroxide: a convenient method for S/G ratio determination

Pyrolysis-gas chromatography in the presence of tetramethylammonium hydroxide (TMAH) was applied to the determination of the ratio of the abundances of the syringyl beta-aryl ether subunits to those of the guaiacyl equivalents (S/G) in lignin. Diazomethane-methylated kenafs (Hibiscus cannabinus and Hibiscus sabdariffa) and beech (Fagus crenata) in situ lignins were employed. Relative abundances of pyrolysis products derived from the guaiacyl and syringyl beta-aryl ether subunits were determined. The S/G ratios for in situ lignins were obtained with average 3.1% relative standard deviation for a minimum of six repeated runs. The S/G ratios determined by pyrolysis in the presence of TMAH agreed well with those determined by thioacidolysis, with a significant linear regression (R(2) = 0.9867). The results showed that pyrolysis with TMAH is an effective tool for obtaining information on the S/G ratio for in situ lignins.     

Significant increases in pulping efficiency in C4H-F5H-transformed poplars: improved chemical savings and reduced environmental toxins

The gene encoding ferulate 5-hydroxylase (F5H) was overexpressed in poplar (Populus tremula x Populus alba) using the cinnamate-4-hydroxylase (C4H) promoter to drive expression specifically in cells involved in the lignin biosynthetic pathway and was shown to significantly alter the mole percentage of syringyl subunits in the lignin, as determined by thioacidolysis. Analysis of poplar transformed with a C4H-F5H construct demonstrated significant increases in chemical (kraft) pulping efficiency from greenhouse-grown trees. Compared to wild-type wood, decreases of 23 kappa units and increases of >20 ISO brightness units were observed in trees exhibiting high syringyl monomer concentrations. These changes were associated with no significant modification in total lignin content and no observed phenotypic differences. C4H-F5H-transformed trees could increase pulp throughputs at mills by >60% while concurrently decreasing chemicals employed during processing (chemical pulping and bleaching) and, consequently, the amount of deleterious byproducts released into the environment.     

Determination of arylglycerol-beta-aryl ethers and other linkages in lignins using DFRC/(31)P NMR

An analytical method for lignins has been developed that involves derivatization followed by reductive cleavage (DFRC), depolymerization, and quantitative (31)P NMR spectroscopy. This technique detects and quantifies the various ether linkages present in softwood residual kraft lignins (RKL) and milled wood lignins (MWL). In addition, the technique supplies new quantitative information about beta-aryl ethers linked to condensed and noncondensed aromatic moieties, including dibenzodioxocins. Within RKL, beta-aryl ether bonds connected to condensed phenolic moieties predominated over those connected to noncondensed phenolic moieties. In addition, the amount of DFRC monomers determined by gas chromatography was minute in the RKL but large in the MWL. This indicates that almost all noncondensed beta-aryl ether linkages were cleaved during kraft pulping. The method offers new avenues for the detailed investigation of the bonding patterns of native and technical lignins.     

Fractionation of bagasse into cellulose, hemicelluloses, and lignin with ionic liquid treatment followed by alkaline extraction

Lignocellulose materials are potentially valuable resources for transformation into biofuels and bioproducts. However, their complicated structures make it difficult to fractionate them into cellulose, hemicelluloses, and lignin, which limits their utilization and economical conversion into value-added products. This study proposes a novel and feasible fractionation method based on complete dissolution of bagasse in 1-butyl-3-methylimidazolium chloride ([C(4)mim]Cl) followed by precipitation in acetone/water (9:1, v/v) and extraction with 3% NaOH solution. The ionic liquid [C(4)mim]Cl was easily recycled after concentration and treatment with acetonitrile. (1)H NMR analysis confirmed that there was no obvious difference between the recycled [C(4)mim]Cl and fresh material. Bagasse was fractionated with this method to 36.78% cellulose, 26.04% hemicelluloses, and 10.51% lignin, accounting for 47.17 and 33.85% of the original polysaccharides and 54.62% of the original lignin, respectively. The physicochemical properties of the isolated fractions were characterized by chemical analysis, high-performance anion exchange chromatography (HPAEC), gel permeation chromatography (GPC), Fourier transform infrared (FT-IR), and (1)H and 2D (13)C-(1)H correlation (HSQC) nuclear magnetic resonance spectroscopy. The results showed that the acetone-soluble lignin and alkaline lignin fractions had structures similar to those of milled wood lignin (MWL). The easy extraction of the noncellulose components from homogeneous bagasse solution and amorphous regenerated materials resulted in the relatively high purity of cellulosic fraction (>92%). The hemicellulosic fraction was mainly 4-O-methyl-D-glucuronoxylans with some α-L-arabinofuranosyl units substituted at C-2 and C-3.     

Structural characterization of the lignin in the cortex and pith of elephant grass (Pennisetum purpureum) stems

The structure of the lignin in the cortex and pith of elephant grass (Pennisetum purpureum) stems was studied both in situ and in isolated milled "wood" lignins by several analytical methods. The presence of p-coumarate and ferulate in the cortex and pith, as well as in their isolated lignins, was revealed by pyrolysis in the presence of tetramethylammonium hydroxide, and by 2D NMR, and indicated that ferulate acylates the carbohydrates while p-coumarate acylates the lignin polymer. 2D NMR showed a predominance of alkyl aryl ether (β-O-4') linkages (82% of total interunit linkages), with low amounts of "condensed" substructures, such as resinols (β-β'), phenylcoumarans (β-5'), and spirodienones (β-1'). Moreover, the NMR also indicated that these lignins are extensively acylated at the γ-carbon of the side chain. DFRC analyses confirmed that p-coumarate groups acylate the γ-OHs of these lignins, and predominantly on syringyl units.     

Studies on the effect of ball milling on lignin structure using a modified DFRC method.

The structures of milled wood lignin (MWL), cellulolytic enzyme lignin (CEL), and residual lignin (REL) from a loblolly pine were analyzed using a modified derivatization followed by reductive cleavage (DFRC) method developed to allow the quantitative determination of three different structural monomeric products originating in lignin: phenolic beta-O-4, alpha-O-4, and etherified beta-O-4 structures. Results show that MWL and CEL are structurally identical, with an increased phenolic beta-O-4 content compared to that of the original Wiley milled wood. These results indicate that the portion of lignin linked to carbohydrates and that not linked to carbohydrates are structurally the same. Modified DFRC analysis of the effect of ball milling on the structure of lignin in wood, MWL, CEL, and REL indicate that vibratory ball milling does not change the lignin structure provided certain precautions are taken. Specifically, dry vibratory ball milling under a nitrogen atmosphere causes substantial structural changes including condensation, whereas vibratory ball milling in toluene had little effect on the lignin structure. This indicates that the structural differences observed in MWL and CEL arise because of the extraction procedure, which preferentially extracts phenolic lignin structures. MWL and CEL are representative of the total lignin in wood; however, due primarily to the solvent extraction process, higher phenolic hydroxyl contents are observed. Nitrobenzene oxidation showed structural results similar to those from the modified DFRC method.