Durable multifunctional properties on acrylic fabric using nano TiO2 and polysiloxane

Producing fabric with multifunctional properties has been recently a center of research and utilizing nanoparticles is an efficient approach to gain this purpose. Here, nano TiO₂ photo catalyst and polysiloxane softener were utilized as stabilizer on the acrylic fabric to obtain soft handle, hydrophilic, and self-cleaning features on the fabric. The effect of various concentrations of nano TiO₂ and polysiloxane on the fabric handle, water droplet absorption time, and self-cleaning properties of the fabric has been mathematically modeled based on the response surface methodology (RSM). The optimized treatment conditions indicated that treated acrylic fabric with 2.19 % polysiloxane and 0.68 % nano TiO₂ produced the rigidity of 26.8 g.cm, water absorption time of 15.8 s and self-cleaning of ΔE _T *=18.1. Also increasing the concentration of polysiloxane enhanced both wettability and photoactive properties of nano TiO₂ treated acrylic fabrics. Further, the nano TiO₂/polysiloxane treated acrylic fabrics is significantly enable to absorb the light with wavelength lower than 400 nm and improve discoloration of C.I. Reactive Yellow 1.     

Functionalization of lyocell fibers with TiO2, SiO2, and GLYMO

In the research self-cleaning coatings based on photocatalytically active nano titanium dioxide (TiO₂) were prepared. When applied directly to cellulose fiber surfaces, TiO₂ coatings form weak bonds with fibers. Therefore 3-glycidooxypropyl-trimethoxysilane was used as a coupling agent. It had been applied on the surface of cellulose fibers before the TiO₂ coating was performed. In this case, the silane is in the interface region, where it can be most effective as an adhesion promoter. Silane coupling agents have unique chemical and physical properties not only to enhance bond strength, but more importantly to prevent de-bonding at the interface during composite aging and use as well. The coupling agent provides a stable bond between two otherwise poorly bonding surfaces. Surface properties of these coatings have been examined, such as surface morphology and surface microstructure. TiO₂ nanoparticles were irreversibly attached to the surface of monodisperse silica (SiO₂) spheres and to the surface of Lyocell fibers coated with an epoxy-containing silane coupling agent. Analysis using scanning electron microscopy showed uniform distribution of nanoparticles in the resulting coatings. Fourier transform infrared spectroscopy revealed changes in the surface microstructure occurring after different modifications. In addition, the influence of photocatalytic activity on the mechanical properties of Lyocell fibers was determined. In addition to that, the results indicated that SiO₂ and the coupling agent provide a protection against high oxidizing power of TiO₂ under exposure to daylight irradiation.     

Investigation on the effect of titanium dioxide nano particles on camouflage properties of cotton fabrics

Cotton fabrics were dyed with three commercial vat dyes in order to provide camouflage in Vis-NIR regions and imitate reflectance profile of greenish leaves. To investigate the effect of nano particles on camouflage properties of dyed fabric, nano particles of TiO₂ were applied on dyed fabrics using pad-dry-cure method. The nano TiO₂ padded dyed fabrics were investigated using scanning electron microscopy (SEM). Reflectance curves of coated dyed samples with different concentrations of nano TiO₂ were measured. Results showed that in both of the standard shades, nano TiO₂ increases the reflectance value in NIR region and with increasing the concentration of nano TiO₂, the reflectance curves of samples tend to show the maximum reflection of greenish leaves (deciduous leaves) in NIR region. Chromatic values (CIE1976 L*, a*, and b*) and color difference (according to CIECMC color difference ΔE*cmc (2:1)) of each of the coated samples were measured using the reflection spectrophotometer. By considering the influence of white color of nano TiO₂ on green shade of dyed cotton fabrics and increasing the color difference (between coated samples and the standard shades of the 1948 U.S army pattern) in visible range, optimum concentrations of nano TiO₂ for development of camouflage properties on cotton fabrics in both NIR and visible region were determined. These values for NATO and forest green shades were 0.75 % and 0.5 %, respectively. Fastness results showed that both of the samples have acceptable color fastness. The effect of washing and exposure to light on camouflage properties of coated dyed fabrics in visible (in term of chromatic values) and NIR region (in term of spectral reflectance) was investigated when those were coated in optimum concentrations of nano TiO₂. The results showed that the effect of after treatments (washing and exposure to light) on surface color spectral characteristics and camouflage properties was inconsiderable.     

Multifunctional modification of wool fabric using graphene/TiO<Subscript>2</Subscript> nanocomposite

In this study, a new finishing technique is introduced through treatment of wool fabric with graphene/TiO₂ nanocomposite. Graphene oxide/titanium dioxide nanocomposite first applied on the wool fabric by hydrolysis of titanium isopropoxide in graphene oxide suspension and then this coating chemically converted by sodium hydrosulfite to graphene/TiO₂ nanocomposite. The homogenous distribution of the graphene/TiO₂ nanocomposite on the fiber surface was confirmed by field emission scanning electron microscopy (FE-SEM), Energy-dispersive X-ray spectroscopy (EDS) and X-ray mapping. X-ray diffraction patterns proved the presence of titanium dioxide nanoparticles with a crystal size of 127 Å on the treated wool fabric. Also, the defect analysis based on X-ray photoelectron spectroscopy (XPS) established the composition of the nanocomposite. Other characteristics of treated fabrics such as antibacterial activity, photo-catalytic self-cleaning, electrical resistivity, ultraviolet (UV) blocking activity and cytotoxicity were also assessed. The treated wool fabrics possess significant antibacterial activity and photo-catalytic self-cleaning property by degradation of methylene blue under sunlight irradiation. Moreover, this process has no negative effect on cytotoxicity of the treated fabric even reduces electrical resistivity and improves UV blocking activity.     

Effect of nano SrTiO3 supporting nano TiO2 on self-cleaning of cotton fabric

This study reports the results of an investigation aiming at finding what affect nano titania (TiO₂) and nano strontium titanate (SrTiO₃) on self-cleaning of cotton fabrics. The photocatalytic activity of nano strontium titanate has been examined on cotton fabric under UV irradiation in various concentrations in mixing of nano titania. The amount of loaded nano titania and nano strontium titanate particles on cotton fabrics were investigated using X-ray fluorescence spectrometry (XRF) and crystallinity of coatings by X-ray diffraction spectroscopy (XRD). The treated cotton fabrics, which were stained with two common synthesized dyes, were exposed to 400 W UV radiation for 30 hours and their self-cleaning property was investigated by a reflectance spectrophotometer. Scanning electron microscope (SEM) images show pervasion of nano materials on the surface of the treated cotton. Adding nano strontium titanate to nano titania showed the most promising photocatalytic activity toward dye degradation.     

Nano-TiO<Subscript>2</Subscript> based multilayer film deposition on cotton fabrics for UV-protection

Nano-TiO₂ based multilayer nanocomposite films were fabricated on cationically modified woven cotton fabrics by layer-by-layer molecular self-assembly technique. Cationization process was used to obtain cationic surface charge on cotton fabrics. Attenuated total reflectance Fourier transform infrared spectroscopy analyses were used to verify the presence of cationic surface charge and multilayer films deposited on the fabrics. Scanning electron microscope micrographs of poly(sodium 4-styrene sulfonate)/TiO₂, nano polyurethane/TiO₂, and TiO₂/poly(diallyldimethylammonium chloride) multilayer films deposited on cotton fabrics were taken. With nano-TiO₂ based multilayer film deposition, the protection of cotton fabrics against UV radiation is enhanced. The UV protection durability of the self-assembled multilayer films deposited on the cotton fabrics was analyzed after 10 and 20 washing cycles at 40 °C for 30 min. Air permeability and whiteness value analysis were performed on the untreated and multilayer film deposited cotton fabrics. The effect of layer-by-layer deposition process on tensile strength properties of the warp and weft yarns was determined.     

Self-cleaning Properties of Nylon 6 Fabrics Treated with Corona and TiO<Subscript>2</Subscript> Nanoparticles under Both Ultraviolet and Daylight Irradiations

Nylon 6 fabric with self-cleaning properties was prepared by corona discharge pre-treatment and coating with TiO₂ nanoparticles (NPs) using pad-dry-cure technique. The self-cleaning property was studied by discoloration of methylene blue (MB), ketchup, tea and coffee stains from the corona+TiO₂ treated nylon-6 fabric. Color difference (ΔΕ*), reflectance (R) and K/S of MB stain were investigated by diffuse reflectance spectrophotometry. The MB stain was almost completely removed from the corona+TiO₂ treated nylon surface after 24 h under UV light/daylight irradiation. Both of these phenomena (corona and TiO₂) led to an increase in the discoloration of stains under UV and daylight irradiations. The EDS analysis showed an increase in the concentration of deposited TiO₂ NPs coating after corona treatment. The FE-SEM images revealed that the surface of nylon 6 was coarser after the corona treatment. Also, the FE-SEM micrographs exhibited that a uniform layer of TiO₂ NPs was formed on the corona treated nylon fabric. The corona+TiO₂ treated nylon illustrated antibacterial activity against E. coli and B. subtillis microorganisms. The EDS and FE-SEM analysis confirmed that after 5 washing cycles, the amount of TiO₂ NPs was higher on the surface of corona+TiO₂ treated nylon than that of the fabric only treated with TiO₂ without corona pretreatment. This result justifies that the corona+TiO₂ treated nylon fabric with appropriate self-cleaning property can be applied cost-effectively in the textile industry.     

Multifunctional polyester fabric using a multicomponent treatment

In this study, multifunctional polyester fabrics with the features of self-cleaning, water and stain repellency, and thermal stability were prepared utilizing a multicomponent system. To this end, both unmodified and alkaline-hydrolyzed modified fabrics were treated with nano TiO₂/citric or maleic acid/sodium hypophosphite/polysiloxane and triethanolamine via a pad-dry-cure method. Surface morphology and color variation of the samples were studied utilizing field emission scanning electron microscopy (FESEM) and CIE-Lab system, respectively. Also, energy-dispersive X-ray (EDX) analysis indicated the content of Ti, P and Si on the surface of fabrics. Thermal stability of the specimen was scrutinized through thermal gravimetric analysis (TGA) and char yield. Both hydrolysis treatment and silicone softener increased the uptake of the nanoparticles. Also, in a comparison between the utilized carboxylic acids, citric acid demonstrated superior features. Generally, the treated fabrics showed desirable self-cleaning and stain repellency with some enhanced thermal stability.     

Relationship between curing temperature and low stress mechanical properties of titanium dioxide catalyzed flame retardant finished cotton fabric

N-methylol dimethylphosphonopropionamide is a flame-retardant agent commonly combined with melamine resin and phosphoric acid catalyst to impart flame-retardant property to cotton fabrics. A co-catalyst titanium dioxide (TiO₂) is added into the formulation in order to improve the flame-retardant performance by enhancing the crosslinking reaction and physically attaching on to cotton fabrics. The fabrics cured at temperature of 150 °C and 170 °C have a better flame-retardant ability and can withstand multiple times of home laundering compared with those cured at temperature of 110 °C and 130 °C. The flame-retardant ability is further enhanced by treating the fabrics in the presence of TiO₂. In addition, the low stress mechanical properties measured by Kawabata Evaluation System for Fabric (KES-F) are altered after flame-retardant treatment. These changes are contributed by the formation of crosslinks after treatment, acid-catalyzed depolymerization in a strong acidic medium and the presence of co-catalyst TiO₂. In addition, the properties of cotton fabrics depend greatly on the choice of curing temperature. High curing temperature usually caused poor hand properties of the fabrics due to the extensive crosslinks formation. Lastly, the existence of TiO₂ in the treatment not only improves the reaction efficiency but also has positive enhancement with respect to compressional recovery ability and tensile properties.     

Experimental study on dyeing technical PET yarns having different TiO<Subscript>2</Subscript> contents

TiO₂ contents in yarns can influence color yield so that dyeing quality of industrial poly ethylene terephthalate (PET) yarns can be improved through the adjustment of TiO₂ contents. To evaluate the dyeing performance of color yield, the chips which included the different TiO₂ contents of 330, 550, and 1,100 ppm respectively were used to produce the yarns of different TiO₂ content by a spin-draft machine. The physical and structural properties of the yarns were measured to investigate effect of the TiO₂ contents on them. Dye uptake and dyeing rate were also evaluated using a colorimeter to compare the yarns having different TiO₂ contents. The experimental results showed that there were no appreciable variation in physical and structural properties among the yarn samples and no difference were observed among the dyed fabric samples with regard to dyeing uptake and dyeing rate. However, the color yield of dyed fabrics increased as TiO₂ contents decreased in the yarns especially when the fabric samples were dyed to pale shade. The physical reasoning could be proposed on why the yarns having low TiO₂ contents appeared to have higher color yield after dyeing.     

A Novel Green Stabilization of TiO<Subscript>2</Subscript> Nanoparticles onto Cotton

Facile embedding of TiO₂ nanoparticles onto cotton fabric has been successfully attained by ultraviolet light irradiations. The adhesion of nanoparticles with fibre surface, tensile behaviour and physicochemical changes before and after ultraviolet treatment were investigated by scanning electron microscopy, energy dispersive X-ray and inductive couple plasma-atomic emission spectroscopy. Experimental variables i.e. dosage of TiO₂ nanoparticles, temperature of the system and time of ultraviolet irradiations were optimised by central composite design and response surface methodology. Moreover, two different mathematical models were developed for incorporated TiO₂ onto cotton and tensile strength of cotton after ultraviolet treatment and used further to testify the obtained results. Self-clean fabric through a synergistic combination of cotton with highly photo active TiO₂ nanoparticles was produced. Stability against ultraviolet irradiations and self-cleaning properties of the produced fabric were evaluated.     

Green Approach for Multifunctionalization of Cellulose-Containing Fabrics

Development of multifunctional textile and clothing products with improved environmental profiles has been demanded both by textile industry and by consumer. Herein, dialdehyde sodium alginate (DASA) and dialdehyde carboxymethyl cellulose (DACMC) have been prepared, characterized and utilized, as an eco-friendly binding/ macromolecular crosslinking/hand building agents, in functional finishing of cellulose-containing fabrics. Fabric samples were treated with the nominated dialdehyde polysaccharide (DAPS, 10 g/l) along with the reactant resin (DMDHEU, 50 g/l), Ag- or TiO₂-NPs as active ingredients (20 g/l) and ammonium persulfate catalyst (5 g/l) using the padding method. After functional finishing, the finished fabrics demonstrated a remarkable improvement in their antibacterial efficacy, UV-blocking ability, self-cleaning capacity, and surface roughness functionality without adversely affecting fabrics resiliency. The variation in these functional properties is affected by kind of DAPS, type of added nanoparticles as well as the treated substrate. Additionally, FTIR, SEM, EDS, and durability to wash measurements for selected samples were performed. Moreover, pre-oxidation of DAPS, functionalization reactions/interactions among the nominated reactants and the textile materials were also suggested.     

Homogeneous self-cleaning coatings on cellulose materials derived from TIP/TiO2 P25

The aim of this research was to study TiO₂ nanocoatings formation and to investigate their self-cleaning effects when applied on cellulose materials. Two different approaches for achieving nanocoatings were used. First, coatings were generated in situ through an acid and alkaline catalyzed sol-gel process with or without added water. Another type of coatings was prepared starting from commercial TiO₂ P25 powder. In order to acquire homogeneous coatings from TiO₂ P25 nanoparticles with uniform nanoparticles size distribution, pH of aqueous TiO₂ P25 dispersions was varied. The dispersion preparation conditions were studied by dynamic light scattering (DLS) and zeta potential (ζ-potential) analysis. The resulting TiO₂ nanocoatings were analyzed in terms of their surface morphology using scanning electron microscopy (SEM). Nanocoatings obtained from pure aqueous dispersions of TiO₂ P25 nanoparticles were inhomogeneous with huge agglomerates; however by changing the pH of dispersion and consequently changing the surface charge of TiO₂ P25 nanoparticles as well, more homogeneous nanocoatings with uniform TiO₂ nanoparticles distribution were prepared. Significant differences between solgel derived coatings were observed. Sol-gel process without added water yielded more homogeneous coatings than sol-gel process with addition of water. Completely different surface morphologies were obtained using alkaline or acid catalyst. Acid catalyzed sol-gel process yielded nanocoatings with long, extended, thin structures; contrary, under alkaline conditions particles grow in size with decrease in number. Fourier transform infrared (FTIR) spectroscopy was used to study the coatings’ microstructure. Furthermore the formation of mono-disperse nanoparticles on the fiber surface resulted in enhanced photocatalytic activity. Degradation of colored stain applied on TiO₂-treated samples was investigated by colorimetric measurements. Photocatalytic activity of nanocoatings prepared via acid catalyzed sol-gel process without water addition was comparable to that of nanocoatings derived from aqueous dispersions of commercial TiO₂ P25 nanoparticles.     

In situ loading TiO<Subscript>2</Subscript> and its photocatalysis and UV resistance on cotton fabric

Anatase TiO₂ nanoparticles was in-situ formed on the cotton fabric by using tetrabutyl titanate (TBT) as a precursor through the normal pressure hydrothermal method. X-ray diffraction (XRD), Scanning electron microscopy (SEM), UV visible spectra (UV-VIS), ATR-IR were used as the characterization techniques. Photocatalytic performance of TiO₂ on the fabric surface was evaluated by methylene blue (MB), 4 kinds of the common living stains and three dyes under ultraviolet and visible light radiation. XRD analysis found that the TiO₂ loaded on the fabric was mainly anatase crystalline phase with particle size of 6.4 nm. SEM observed that a large number of nano TiO₂ particles are distributed on the fabric surface. UV-VIS test indicated that theTiO₂-coated fabric possessed an obvious absorption for ultraviolet. ATR-IR analysis indicated that the nano-TiO₂ possesses a strong affinity with the hydroxyl group of the cotton fabric, and the soaping tests showed that the TiO₂ was firmly bonded with the fabrics. The treated fabrics have good degradation ability for MB aqueous solution, and could degrade azo, anthraquinone and phthalocyanine dyes. The order of degradation of the common life stains was: pepper oil> tea > coffee > soy sauce.     

Immobilization of TiO2 nanoparticles on PET fabric modified with silane coupling agent by low temperature hydrothermal method

PET fabric was first modified with silane coupling agent KH-560, and then was loaded with a layer of nano-scaled TiO₂ particles using tetrabutyl titanate as precursor by low temperature hydrothermal method, followed by dyeing with Disperse Blue 56. The morphology, crystalline phase, chemical modification, thermal stability and optical property of PET fiber before and after treatments were studied by scanning electron microscope, X-ray diffraction, X-ray photoelectron spectroscopy, thermal gravimetric and diffuse reflectance spectrum techniques. The properties of tensile, air permeability, luster, ultraviolet (UV) protection, photocatalytic activity, K/S value and color fastness were also measured. It was found that compared with the TiO₂-coated fabric without modification with KH-560, the loading of TiO₂ nanoparticles on the surface of the TiO₂-coated fabric modified with KH-560 was obviously improved. The pure anatase TiO₂ nanoparticle was grafted onto the fiber surface. The onset decomposition temperature increased. The absorbing capability to ultraviolet radiation was enhanced. The properties of tensile, air permeability, luster, K/S value and color fastness changed slightly. The UV protection ability and photodegradation of methyl orange under UV illumination were enhanced to some extent.     

Superhydrophobicity,Self-cleaning and Flame Retardancy Properties of Cotton Fabric

A simple and facile method for fabricating the cotton fabric with superhydrophobicity, self-cleaning and flame retardancy was described in the present work. Three types of antimony pentoxide sol (Sb₂O₅), aluminum hydroxide sol (Al(OH)₃) and 1H,1H,2H,2H-perfluorodecyltriethoxysilane (fluoroalkyl silanes) were used as coating for the cotton fabric. It was found that Sb₂O₅ and Al(OH)₃ exhibited significant synergistic effects on the flame retardancy. When the weight ratio of Sb₂O₅/Al(OH)₃(content 30 wt%) was 1:3, the results showed that the limiting oxygen index (LOI) value was 45.1 %, smoke density (SDR) value was 35 %, and it still passed UL94 V-0 rating. The cotton fabrics coated with fluoroalkyl silanes/Sb₂O₅/ Al(OH)₃ showed a superhydrophobicity, anti-contamination and self-cleaning properties. In addition, the results exhibited the outstanding superhydrophobicity, oil/water separation, excellent waterproofing durability and flame retardancy of cotton fabric after 1000 cycles of washing by water, the LOI value was 40.1 %, SDR value was 39 % and WCA was 152° after 1000 cycles of washing. We believe that this simple, environmentally friendly and versatile fabrication of the cotton fabric had excellent real-life applications.     

Effect of concentration of titanium dioxide acting as catalyst or co-catalyst on the wrinkle-resistant finishing of cotton fabric

The wrinkle-resistant property of cotton specimens treated by 1,2,3,4-butanetetracarboxylic acid (BTCA) and catalysed by sodium hypophosphite (SHP) in the presence of TiO₂ or nano-TiO₂ has been evaluated in the present study. In this study, Scanning Electron Microscopy proved the presence of TiO₂ or nano-TiO₂ on the fibre surface. It was also found that 0.1–0.2 % TiO₂ or nano-TiO₂ was the optimum concentration to enhance the wrinkle-resistance of BTCA-SHP-treated cotton fabrics. In addition, the TiO₂ or nano-TiO₂ added in the wrinkle-resistant treatment could act as a multi-functional finishing agent to improve the UV protection property while they are safe to human skin as proved by the cytotoxicity test. Therefore, TiO₂ or nano-TiO₂ was evident that they could enhance the finishing performance and minimise the side effect.     

Multifunctional melt-mixed Ag/TiO2 nanocomposite PP fabrics: Water vapour permeability, UV resistance, UV protection and wear properties

This research deals with the investigating the effect of nanoparticles on the various properties of nanocomposite fabrics produced from melt spinning of various blend ratios of prepared masterbatch containing Ag/TiO₂ nanoparticles. The results revealed that the wear properties of modified fabrics improved as compared to pure fabrics with a trend justified considering modulus or crystallinity of fabrics with opposite effects. About 40 % UV protection enhancement has been obtained applying this kind of nanoparticles in the close relationship with the crimp contraction of textured yarns. A considerable improvement in the garment comfort has been recorded for nanocomposite sample containing 1 wt% nanoparticles. The lower permeability at low environment temperature and a higher at higher one, as compared to the pure sample, were obtained using this sample. It is highly interesting that these desirable changes in permeability can be achieved in the range of common environment temperatures (15–35 °C) being adapted to the human body requirements. The changing point is about 25 °C exactly meeting the body requirements by changing environment temperatures. A UV-induced solid state nanocomposite interaction increasing wear properties of UV-irradiated nanocomposite fabrics has been discovered.     

Fabric objective measurement of the plasma-treated cotton fabric subjected to wrinkle-resistant finishing with BTCA and TiO<Subscript>2</Subscript> system

Handle is an important factor when designing the end-uses of fabric as it is also a critical factor for purchasing decision. In the present study, the Kawabata Evaluation System for Fabrics (KES-F) was used for measuring the fabric handle of BTCA-TiO₂ treated cotton fabric with or without plasma pre-treatment. The results revealed that the BTCA-TiO₂ treated cotton fabrics without plasma pre-treatment had a negative effect on tensile, shearing, compressional, and surface properties while the bending properties were improved. On the other hand, the plasma pre-treatment improved the tensile and compressional properties, but not the bending, shearing, and surface properties.     

Sound absorption properties of spiral vane electrospun PVA/nano particle nanofiber membrane and non-woven composite material

In this research, we fabricated a series of PVA membranes loaded with 0 wt.%, 1 wt.%, 3 wt.%, 5 wt.% ZrC and 0 wt.%, 1 wt.%, 3 wt.%, 5 wt.% TiO₂ using a spiral vane electrospun machine respectively. There were 2 sizes of TiO₂ nano particles: 10 nm and 200 nm. We tested sound absorption properties of needle-punched nonwovens as well as the composite of nano membranes and needle-punched nonwovens by an impedance tube at the frequency range from 500 Hz to 6500 Hz. Besides, we tested morphological characterization of nano membranes by scanning electron microscope (SEM) and crystalline properties by X-ray diffraction (XRD). We investigated the sound absorption properties of composites as well as the effect of ZrC, TiO₂, nano particle sizes and cavity depth on sound absorption properties. Results showed that sound absorption properties of composites increased at the whole range of frequency compared to those of needle-punched nonwovens. When loaded with ZrC nano particles, sound absorption properties of composite shifted to a higher frequency region, and with increasing content of ZrC, sound absorption properties were better above 2500 Hz. However, when loaded with TiO₂, sound absorption properties were better at lower frequency. With 3 wt.% TiO₂, sound absorption coefficient reached the best at the frequency range from 500 Hz to 1500 Hz. Besides, 200 nm TiO₂ was more conductive to the increase of sound absorption properties at lower frequency region compared to 10 nm TiO₂. Sound absorption properties of composites with air back cavity shifted to a lower frequency region, too. SEM showed that there was nano particle aggregation when loaded TiO₂ nano particles. XRD showed that ZrC nano particles loaded in PVA nano fiber retained their crystalline structure while TiO₂ didn’t. It appeared from the results that nano particles had an effect on sound absorption materials, with different kinds and different sizes, sound absorption properties will improve in different ranges of frequency