Dynamic Constitutive Model of Steel Fiber Reinforced Concrete and Its Finite Element Method

Taking the split Hopkinson pressure bar(SHPB) test data as training samples, an implicit dynamic constitutive model of steel fiber reinforced concrete(SFRC) was proposed with the improved BP neural network program. On the basis of ABAQUS/Explicit, a user defined material subroutine VUMAT was compiled with FORTRAN language, embedding with the neural network constitutive model into finite element calculation. With SFRC structure＇s response under impact load as case study, it is shown that the constructed constitutive model and its finite element method are effective.     

Mixed Finite Element Method for Dynamic Problems of Fluid Saturated Biphasic Porous Media

Based on the fluid saturated biphasic porous media model deduced from mixture theory,a finite element formulation with u S u F p variables for dynamic response analysis is given out.This method overcomes the difficulty of choosing suitable penalty parameter in penalty finite element method,and the accuracy of pressure distribution obtained with the mixed finite element method is higher than the penalty finile element method.An iterative solution method is suggested to solve the system of equations whose coefficient matrices are non positive definite.It is concluded from patch test that the order of interpolation function for pressure variables must be higher than that of displacement variables of solid phase.     

Reinforcement of Hydrated Calcium Silicate Powder to Silicone Rubber

In the conditions of low temperature and low pressure, the white hydrated calcium silicate powder was produced through the dynamic hydrothermal synthesis technology. Through studying the properties of hydrated calcium silicate powder which is made by different synthesis temperature and the influence of hydrated calcium silicate powder,calcium carbonate and quartz powder on the mechanical properties of silicone rubber, it is found that the hydrated calcium silicate powder which is produced at （120±5）℃ has better performance enhancement. Besides the size of particle, the surface reactivity is also an important factor.     

A Finite Element Method for Quasi Static Problems of Two phase Porous Media

For the quasi static problems of two phase porous media,the velocity variable of fluid phase can be eliminated as the viscosity of fluid is neglected.The corresponding governing equations,with displacement of solid phase and pore pressure as basic variables,as well as the boundary and initial conditions are given out.Finally a mixed finite element formula with u S-p variables is obtained with weighted residual method.This method has lesser nodal variables and higher accuracy of pressure distribution.     

Mixed Finite Element Formulation of the Linear Biphasic Theory for Soft Tissues

The behavior of soft tissues of human musculoskeletal system can be describedwith the biphasic model based on a continuum theory of mktures. This paper. using Galerkin weight-ed residual method.obtains a mixed finite element formulation for the linear biphasic model of smalldeformation. and. in turn. gives out the iterative scheme solving the system equations. The results ofnumerical analysis for the constrained compression problem are consistent with those obtained bytheory. which illustrates the correctnas and feasibility of the derived mixed finite element formula-tion. concludingly. this formulation provides an effective means of numerical analysis for the motfonmechanism of human articulating joints.     

Finite Element Analysis of Spatially curved Rods

A system of governing equations for spatially curved rods are derived in natural coordinate,and an analytic solution to the statically determinate problem is given.Based on the solution,a generalized displacement model for element of curved bars is developed,which is convergent and accurate.     

Coupled Thermo-Elastic Contact Finite Element Method and It''s Application in Gearing

A new finite element method is presented in this paper to analyze the thermo- elastic contact problem with heat input on meshing tooth faces. The computational model of meshing gear has been established and the frictional heat input on meshing tooth faces is estimated. In addition, 2-D finite element analysis program for this kind of problem is listed. The test and practical examples are given to show the validity and versatility of this method.     

The Finite Element Method for Frame Structure with Fuzzy Elastic Connections

The connections of frame structure elements at a node are ofen an elastic connection between hinged and rigid.In this paper,the stiffness matrix and the loading transfer matrix of frame element with turn elastic connections is deduced,the cross shear effect has been taken into consideration simultaneously.The stiffness matrices of some bar elements,such as both ends of the bar are hinged or rigid and one end is hinged but the other is rigid,are special cases of the stiffness matrices presented in this paper.After pointing out that the elastic coefficient at a node of a bar element with elastic joint is really a fuzzy quantity,the fuzzy stiffness matrix of the bar element is obtained,and a solution to structural fuzzy finite element equilibrium equations is presented.The fuzzy solution obtained from above is not only containing the solution of ordinary finite element method but also providing some additional informations with practical value.[WT5HZ]     

Deformable B-spline Curves and Surfaces Model and Its Finite Element Solution

Deformable models are of great importance for contour extraction and surface reconstruction, which cause the deformable models deform to the object contours due to simulated external force.Deformable B spline models can share the merit of the popular used B splie. From the Lagrangian mechanics, the dynamics equation of deformable B spline curve and surface is derived. Its finite element solution is studied including the finite element generation and element matrix calculation. A example is given to verify its validity.     

Finite Element Programming Based on Template Chain Structure

Traditional Finite Element Method is the structuralization programming method and the structuralization language (such as FORTRAN). Its data store uses fixed array structure, which makes the expanding ability of program limited, code's reuse ratio low, debugging complex. The template is an opposite new important characteristic of the object-oriented programming language C++. The template can quickly establish class library so as to increase greatly the development speed of the large software. The object-oriented programming concept is applied to finite element method. According to the nature of the finite element analysis, the classes and their methods, which describe virtual element, node, material etc., have been developed and implemented using the object-oriented programming language C++. The elements, nodes and materials are stored by chain. Many type's elements are stored mixedly by polymorphism characteristic. The program is implemented and a instance is given to show the programming of finite element method. The results show that the period of programming and debugging is obviously shorter than that of traditional method; the code's utilization ratio is also increased obviously.     

Finite Element Reliability Analysis of the Stability of a Slope

The whole reliability index of a slope is derived through using the strength reduction method in the finite element analysis, which can make use of the former finite element program and can be used to both linear and nonlinear finite element analysis. The affection of the evaluation of derivative and the selection of reliability analysis methods is discussed, which shows that it is very important to select the type of limit state function of the slope stability. A new iterafive formula, which can consider the correlation of fundamental parameters, is proposed for FORM, and the convergence is very well.     

Finite Element Analysis of Masonry RVE Homogenization Procedure

Homogenization is one of the most important steps in the numerical analysis of masonry structure, where the continuum is used. A masonry representative volume element (RVE) is formed as the equivalent element of masonry components and it is the most important step in homogenization procedure. The RVE is molded with consideration of the material properties of mortar and brick as well as their interaction separately. In this paper the masonry RVE is simulated with the finite element software ANSYS. The stress-strain relationships of RVE subjected to different types of loading conditions are presented. The equivalent elastic modulus and Poisson's ratio are calculated and the feasibility of finite element method used in the procedure of masonry homogenization is demonstrated.     

Application of Extended Finite Element Method to Fracturing Analysis of Gravity Dam

The extended finite element method(XFEM) presented in recent years is a new and effective method for discontinuity analysis,especially fracture problem analyses.The basic XFEM principle is introduced and the technique for fracture analysis is presented.The fracturing process of a gravity dam is simulated by XFEM,and the rules of stresses and displacements distribution are analyzed.Compared with the classical finite element method,the crack growth in the gravity dam can be modeled by XFEM without making the crack surface associate with the finite element mesh and setting dense mesh near the crack tip as well as remeshing after crack growth.The cumbersome work and disadvantages in conducting fracturing analysis by the finite element method thus can be avoided.The predominance of this method for dam fracturing analysis is displayed.     

Finite Element Method of 3D Stable Heat Conduction of Steel Fluid in Continuous Casting Moulds

The heat transfer of steel fluid in continuous casting mould is a stable process and can be depicted with three-dimensional stable heat conduction equation depending on tension speed. The corresponding finite element equation, including the first, second and third boundary conditions, is deduced out with Galerkin residual method. The coded FEM program is used to analyze the temperature distribution of Q235 steel in continuous billet casting mould. The method proposed is a foundation of thermo-mechanical coupled analysis for the formation of solidified shells and stress in the shells in continuous casting.     

1-MCP结合硅窗MAP对新疆毛杏贮藏品质的影响

本文研究了1μL/L 1-甲基环丙烯(1-MCP)、硅窗自发气调包装(MAP)、1-MCP+MAP协同处理对新疆毛杏低温冷藏期间贮藏品质的影响。结果表明,硅窗MAP包装贮藏9 d后,CO2含量维持在3.14%~3.61%之间,O2含量维持在7.88%~9.00%之间,说明硅窗具有较好的气体通过率;1-MCP和MAP单独处理可以显著抑制新疆毛杏的呼吸速率,降低果实乙烯释放量,延缓果实TA、硬度下降速率,维持果实贮藏期感官品质;1-MCP+MAP处理具有协同作用,可显著延缓果实硬度、TA、VC含量和果实色调角值H的下降速率,感官品质评价最好。1-MCP和MAP处理对新疆毛杏均有明显的保鲜效果,1-MCP+MAP处理保鲜效果优于单独处理。     

Finite Element Analysis and Experimental Research on Pedestal of PC Beam for Light Railcar

In design of light railcar used freely supported beam, the cast steel pedestals will bear complex loads, which include weight, acceleration and wind, etc. Because of pedestals' peculiarity and complexity, the strength of the pedestals play an important role in safety of light railcar. So it's necessary to analyze their stress and deformation in order to insure safety of light railcar. Up to now, finite element analysis is still the most effective means. By studying cast steel pedestal with finite element method, 3-D finite element models of fixed and kinetic pedestals were built, and the loads and boundary condition of pedestals were analyzed. By means of finite element analysis software, the contact and von mises stresses were obtained and deformation were resolved. As a result of analysis, the tow of pedestal can fulfill requirement of use in light railcar, the contact stress and von mises stress are not exceeded limit stress strength of materials. There is enough static strength for the structures of pedestals. For verifying theoretical analysis result, the fatigue test was carried out, with examining the testing points locating on the pedestals, the stress and deformation data were measured. By comparing between theoretical analysis and test data, the experimental results show calculated and testing results can meet the case well which assure the reliability of finite element analysis. But in the result, there are differences in deformations of them. The reason may be that boundary conditions and loads are not same between analysis and experiment.     

Finite Element Simulation of Inhomogeneity and Anisotropy of Proximal Femur

To solve implant's looseness and subsidence, and to adapt for the requirement of custom-made hip endoprostheses' rapid automatic design and manufacture, a new method is presented for constituting the anisotropic and inhomogeneous model of proximal femur based on CT, CAD technology and finite element analysis during design of custom-made hip endoprostheses, Raw CT image data, 3-D modeling and finite element software is utilized to set up 3-D finite element model of proximal femur. The model is provided with anisotropy and inhomogeneity by self-developed specific software. The near true proximal femur model is structured and good biomechanics condition is provided for optimize design of custom-made hip endoprostheses. For simulating and analysing of proximal femur's structrue and material mechanics property, and determining stress ,strain and response after-operation under the action of physiological load more exactly, and supplying design of custom-made hip endoprostheses with data, the method can provide biomechanics condition for optimize design of custom-made hip prostheses.