热处理对毛白杨木材物理力学性能的影响

采用蒸汽介质,氧气含量控制在2%以下,在热处理箱内对毛白杨木材进行热处理,研究处理温度(170~230℃)和处理时间(时间1~5 h)对毛白杨木材物理力学性能的影响。结果表明,随着处理温度的提高和处理时间的延长,毛白杨木材的抗胀缩率显著提高,但抗弯强度显著降低;热处理后毛白杨木材的抗弯弹性模量提高。     

Influence of Ammoniacal Copper Quaternary treatments on mechanical properties of blue-stained Lodgepole Pine wood

Three concentrations （2.8%, 2.0%, 1.2%） of Ammoniacal Copper Quaternary （ACQ） was selected to treat Lodgepole pine wood for evaluating ACQ treatment on mechanical properties of blue-stained wood. The bending modules of elasticity （MOE）, modules of rupture （MOR）, toughness and shearing strength parallel to grain on tangential surface, are tested according to the criteria GB1927-1943-91. Non-treated sample were also tested according to the same procedure. The results showed that the three groups specimen impregnated by different concentrations of ACQ solution met the AWPA standard 2003 of America （UC4A 6.4g/cm^3）. There were significant difference of toughness between treated wood and non-treated wood （p=0.01）, but there were no statistically significant differences among three concentrations in terms of toughness, and toughness of treated wood was approximately 20% lower than non-treated. MOR, MOE as well as sheafing strength parallel to grain were found to be not significantly different between treated wood and non-treated one, and there were no statistically significant difference among three concentrations of ACQ too. Toughness, MOR, MOE and sheafing strength parallel to grain increased with decrease of concentration of ACQ, but they were hardly affected by ACQ preservatives.     

Comparative study on three dynamic modulus of elasticity and static modulus of elasticity for Lodgepole pine lumber

The dynamic and static modulus of elasticity （MOE） between bluestained and non-bluestained lumber of Lodgepole pine were tested and analyzed by using three methods of Non-destructive testing （NDT）, Portable Ultrasonic Non-destructive Digital Indicating Testing （Pundit）, Metriguard and Fast Fourier Transform （FFT） and the normal bending method. Results showed that the dynamic and static MOE of bluestained wood were higher than those of non-bluestained wood. The significant differences in dynamic MOE and static MOE were found between bulestained and non-bluestained wood, of which, the difference in each of three dynamic MOE （Ep. the ultrasonic wave modulus of elasticity, Ems, the stress wave modulus of elasticity and El, the longitudinal wave modulus of elasticity） between bulestained and non-bluestained wood arrived at the 0.01 significance level, whereas that in the static MOE at the 0.05 significance level. The differences in MOE between bulestained and non-bluestained wood were induced by the variation between sapwood and heartwood and the different densities of bulestained and non-bluestained wood. The correlation between dynamic MOE and static MOE was statistically significant at the 0.01 significance level. Although the dynamic MOE values of Ep, Em, Er were significantly different, there exists a close relationship between them （arriving at the 0.01 correlation level）. Comparative analysis among the three techniques indicated that the accurateness of FFT was higher than that of Pundit and Metriguard. Effect of tree knots on MOE was also investigated. Result showed that the dynamic and static MOE gradually decreased with the increase of knot number, indicating that knot number had significant effect on MOE value.     

扭叶松实木板材三种动态弹性模量和静态弹性模量比较研究(英文)

采用Pundit、Metriguard、FFT等三种无损检测方法和常规弯曲法对加拿大扭叶松(lodgepole pine)蓝变与非蓝变实木板材的动态及静态弹性模量进行检测和比较研究。结果表明,蓝变材三种动态弹性模量及静态弹性模量均高于非蓝变材;对比分析表明,蓝变材和非蓝变材的动态及静态弹性模量存在差异,其中动态弹性模量差异均达到0.01显著性水平,静态弹性模量差异达到0.05显著性水平,并且心、边材及密度值不同是导致以上差异的主要原因。相关性分析表明,动态与静态弹性模量间相关性达到0.01显著性水平;尽管三种无损检测方法测量结果存在差异,但它们之间仍存在密切相关性,FFT 技术测量的准确性高于Pundit和Metriguard;板材中结子数影响木材动态和静态弹性模量,随着板材结子数增加弹性模量相应地降低。     

Physical and mechanical properties of wood after moisture conditioning

Some properties of wood (hinoki:Chamaecyparis obtusa) moisture-conditioned by an adsorption process from a dry state and by two desorption processes (from a water-saturated state and from a state with a moisture content slightly below the fiber saturation point) were investigated. The moisture contents of wood conditioned by the adsorption process and by the desorption process continued to approach to one another for the moisture-conditioning period of over 50 weeks. Accordingly, sorption hysteresis should be regarded as a transitional phenomenon that occurs during the process of approaching the true equilibrium, which requires a long time. The wood conditioned by the desorption process beginning from a water-saturated state showed slightly smaller dimensions than those conditioned by the adsorption process with the same moisture content; however, the wood conditioned by the desorption process from a moisture content below the fiber saturation point showed slightly larger dimensions than those conditioned by the adsorption process. The wood conditioned by the adsorption process from a dry state showed a higher modulus of elasticity and modulus of rupture than did the wood conditioned from a water-saturated state with the same moisture content. The mechanical properties of the wood also varied based on the states at which the desorption process was started. This is a notable characteristic of the relation between the drying condition and the mechanical properties of wood.     

Changes in the mechanical properties of wood during a period of moisture conditioning

Changes in the modulus of elasticity (MOE), modulus of rupture (MOR), and stress relaxation in the radial direction of wood (hinoki:Chamaecyparis obtusa) moisture-conditioned by the adsorption process from a dry state and by the desorption process from a moisture content slightly below the fiber saturation point were investigated. The MOE and MOR of wood conditioned by the adsorption process showed significant increases during the later stages of conditioning when the moisture content scarcely changed. However, with the desorption process they did not increase as much during later stages of conditioning, though they increased during early stages of conditioning when the moisture content greatly decreased. The stress relaxation of wood decreased with an increase in the conditioning period with both the adsorption and desorption processes. These results suggest that wood in an unstable state, caused by the existing state of moisture differed from that in a true equilibrium state shows lower elasticity and strength and higher fluidity than wood in a true equilibrium state. Furthermore, the present study demonstrates that the unstable states of wood induced during the course of drying, desorption, and possibly adsorption of moisture are slowly modified as wood approaches a true equilibrium state.     

ACQ各组分对金属腐蚀性的影响

测定ACQ各组分对4种金属的腐蚀性。结果表明,除304不锈钢以外,ACQ对其余3种金属均有较强的腐蚀性;二甲基双癸基氯化铵(DDAC)中的氯离子,是影响ACQ对Q235A钢腐蚀性的主要因素;CuO质量分数和CuO与DDAC的质量比,是影响ACQ对Q235A钢腐蚀性的显著因素。     

Characterization of major,unused, and unvalued Indonesian wood species I. Dependencies of mechanical properties in transverse direction on the changes of moisture content and/or temperature

Mechanical property changes due to the moisture content (MC) and/or temperature changes were examined for 15 Indonesian wood species. A static bending test was carried out at 20°C, 65% relative humidity (air-dry), and water-saturated at 20°C (wet-20) and 80°C (wet-80). For individual test conditions, modulus of elasticity (MOE) and modulus of rupture (MOR) increased linearly with specific gravity regardless of wood species; however, maximum deflection did not correlate with specific gravity for any MC or temperature conditions. The relative values of MOE and MOR measured in wet-20 to air-dry conditions were variously affected from slightly to strongly depending on the wood species. However, the relative values always decreased markedly when saturated in water at 80°C, regardless of wood species. The relative MOE, MOR, and maximum deflection values due to the change in MC or MC and temperature combined were independent of specific gravity but may be dependent on wood type: softwood or hardwood.     

人工林落羽杉力学性能研究

对江汉平原人工林落羽杉物理力学性能进行了研究,结果表明:落羽杉的气干密度为0.413 g/cm3,气干密度等级为轻;综合强度为74 MPa,强度等级为Ⅰ级;径向横纹抗压强度略大于弦向横纹抗压强度;端面硬度最高,弦面硬度与径面硬度差别不大。落羽杉南北面近树皮处木材的密度、抗弯强度、弹性模量、顺纹抗压强度均大于近髓心处,南北方向对落羽杉的密度、顺纹抗压强度在5%水平上差异均不显著,而对其抗弯强度、弹性模量在1%水平上差异显著。     

STUDIES ON PHYSICAL AND MECHANICAL PROPERTIES OF DAHURIAN LARCH-WOOD OF TWO WOOD COLOURS

Dahurian1arch[Larixgmelini(Rupr.)Rupr.jisamaintimbertreespe-ciesinDaxing'anLingForestRegion,and'itisalsoafast-growingandregenerationtreeinNorthChina-Becauseitsecologicalamplitudeisverywild,therearemanyva-riabletypesinvarioushabitats.Themostsignificativetypes,whichhavebeenfoundrecentlyininvestigation,aretheredwoodandwhitewood.Theformerisfromyellow-browntored-brown,andthelat-tCrisfrompaleyellowtowhite.Theyaresimilarto'Redscotchpine#and'Whitescotchpine#.Theparametersofwoodcol-ourandphysico-…     

Influence of biotic factors on the mechanical properties of wood,taking into account the time of harvesting

The aim of the present paper is to investigate the influence of biotic factors (fungi and insects) on the mechanical properties of wood through the effect of blue-stain, taking into account the time of harvesting and the time of stay of wood in the forest. Specifically, the resistance to axial compression and to bending (modulus of rupture (MOR)) was studied using infected specimens of Scots Pine (Pinus sylvestris) and Norway Spruce (Picea abies) (the usual types of wood used in woodwork). The specimens were obtained from logs of Scots Pine and Norway Spruce that were harvested in three different seasons of year, namely in July 2012, November 2012 and June 2013, respectively, in the forest of Elatia-Greece, and the attack pace by biotic factors with respect to the time of logging was studied. The placement of the experimental surfaces of each type of tree was made on skid road and in the stand. Totally, 120 laboratory measurements in axial compression and 120 measurements in bending (MOR) took place. The results proved that blue-stain hardly affect the mechanical properties of both wooden species and particularly the specimens that were derived during the winter logging.