Determination of enantiomers of synthetic pyrethroids in water by solid phase microextraction - enantioselective gas chromatography

Solid phase microextraction (SPME) is an ideal sample preparation technique because of its speed and solvent-free features. Sampling by SPME is selective and only the dissolved concentration is measured, which allows measurement of the bioavailable fraction of a contaminant in aqueous media. One potential application of SPME is for analysis of enantiomers of chiral contaminants in environmental samples. In this study, a method was developed for determining enantiomers of (Z)-cis-bifenthrin and cis-permethrin in water using coupled SPME and enantioselective gas chromatography (GC). Following SPME sampling, enantiomers of (Z)-cis-bifenthrin and cis-permethrin were separated at the baseline on a beta-cyclodextrin-based enantioselective column, and analyte enrichment onto the SPME fiber was not enantioselective. The GC response increased as sampling time was increased from 0 to 240 min, and as sampling temperature was increased from 20 to 40 degrees C. Organic solvents such as methanol, acetone, and acetonitrile enhanced, while soil extracts slightly decreased, the GC response. The integrated SPME-enantioselective GC method was used to analyze surface runoff samples. The analysis showed preferential degradation of the 1S-3S enantiomer over the 1R-3R enantiomer for both (Z)-cis-bifenthrin and cis-permethrin. The concentrations detected by SPME-GC were substantially smaller than those determined following solvent extraction, suggesting that SPME-enantioselective GC analysis selectively measured the dissolved fraction.     

Solid phase microextraction (SPME) of orange juice flavor: odor representativeness by direct gas chromatography olfactometry (D-GC-O)

The sensorial quality of solid phase microextraction (SPME) flavor extracts from orange juice was measured by direct gas chromatogrphy-olfactometry (D-GC-O), a novel instrumental tool for evaluating odors from headspace extracts. In general, odor impressions emerging from SPME extracts poorly resembled that of the original orange juice. In an attempt to improve the sensorial quality of extracts, sample equilibration and exposure times were varied on Carboxen/polydimethylsiloxane (CAR/PDMS) and divinylbenzene/Carboxen/polydimethylsiloxane (DVB/CAR/PDMS) SPME fibers. Best sensorial results were obtained with the DVB/CAR/PDMS fiber exposed for the shortest time; a trained panel of eight assessors judged its odor as the most representative of the reference orange juice. The analysis of odor active compounds by classical GC-O accounted for odor characteristics revealed by D-GC-O. A principal component analysis (PCA) was applied on SPME and headspace extracts using flavor recoveries as variables. Interestingly, PCA discriminated samples according to their odor representations described by D-GC-O analysis. This paper provides the first comprehensive methodology to "smell" SPME extracts and "evaluate" their sensorial quality. This method will enable future investigations to further improve SPME performance.     

Screening for 2-acetyl-1-pyrroline in the headspace of rice using SPME/GC-MS

Solid phase microextraction (SPME) is used to collect and concentrate the compounds in the headspace of rice. This research describes optimization parameters of temperature, moisture, and sampling time. Optimization was based upon the recovered levels of 2-acetyl-1-pyrroline (2-AP), the popcorn aroma in aromatic rice. The method uses a sampling temperature of 80 degrees C and adds 100 microL of water to a 0.75 g sample of rice. The rice was preheated for 25 min, a carboxen/DVB/PDMS SPME fiber was exposed to the headspace for 15 min, and a subsequent GC-MS analysis took 35 min. Samples of rice can be analyzed as the flour, milled kernels, or brown rice. Twenty-one experimental rice varieties were analyzed by the SPME method and compared to a wet technique. Recoveries of several nanograms of 2-AP from 0.75 g samples of aromatic rice were observed, whereas only trace amounts of 2-AP were recovered from nonaromatic rice. Recovery from a single SPME headspace analysis is calculated to be 0.3% of the total 2-AP in the sample.     

The effects of sample preparation and gas chromatograph injection techniques on the accuracy of measuring guaiacol, 4-methylguaiacol and other volatile oak compounds in oak extracts by stable isotope dilution analyses

The deuterium-labeled standards [(2)H(3)]-guaiacol and [(2)H(3)]-4-methylguaiacol were synthesized and utilized in a method employing gas chromatography-mass spectrometry to determine the concentration of guaiacol and 4-methylguaiacol in wine or extracts of oak shavings. The method was combined with previously published methods for 4-ethylphenol, 4-ethylguaiacol, cis- and trans-oak lactone and vanillin, so that all these compounds could be quantified in a single analysis. The method can employ either liquid-liquid extraction or headspace solid-phase microextraction (SPME) and is rapid, robust, precise, and accurate. Under certain conditions, there was artifactual generation, to varying degrees, of guaiacol, 4-methylguaiacol, cis-oak lactone, and vanillin during the analysis of oak extracts, especially when diethyl ether extraction and injector block temperatures at or above 225 degrees C were employed. The most substantial effects were observed for guaiacol, in which results could be exaggerated by over 10 times. These artifacts could be avoided by using headspace SPME or by preparing liquid-liquid extracts with pentane or pentane/diethyl ether (2:1) injected at 200 degrees C providing spot checks using headspace SPME were performed. Data obtained for previously published quantitative determination of guaiacol in oak extracts should be reexamined carefully, with special attention paid to their respective methods of sample preparation and analysis.     

Comparison of strategies for extraction of high molecular weight polycyclic aromatic hydrocarbons from drinking waters

Simple, rapid, and inexpensive methods have been developed for the determination of polycyclic aromatic hydrocarbons (PAHs) in drinking waters without interferences from other chemical contaminants by use of two different extraction techniques and analysis by an optimized reverse-phase (RP) high-performance liquid chromatography followed by fluorescence detection (HPLC-FLD) method. The feasibility of SPE (solid-phase extraction) and SPME (solid-phase microextraction) for the determination of PAH in drinking water samples has been evaluated. Several parameters have been studied and optimized for both extraction procedures. The relationship between the nature of the fibers and the quantity of extracted compounds and the effects of organic solvent, salt addition, sampling temperature, and sampling time was studied for SPME. Acetonitrile percentage added to the sample, sample storage conditions (temperature and time), and type of organic elution solvent and elution volume were evaluated for SPE. The results show that both extraction procedures can be used to determine PAHs in drinking waters, but SPE gives better performance (recovery, precision, and quantification limits) for the determination of PAHs in drinking water at the levels established by the legislation.     

Evaluation of solid-phase microextraction for the isotopic analysis of volatile compounds produced during fermentation by lactic acid bacteria

The use of solid-phase microextraction (SPME) coupled with isotope ratio mass spectrometry (IRMS) for the analysis of flavor compounds produced by lactic acid bacteria has been evaluated using both liquid and headspace sampling modes. Initially, it was necessary to optimize the conditions for the SPME extraction of flavors-diacetyl and acetoin-in standard aqueous solutions. The effects of salt, headspace versus liquid sampling, and coating phase were tested. Second, the suitability of the coupling of SPME and gas chromatography-combustion interface-IRMS (GC-C-IRMS) for the determination of delta(13)C values was assessed. It is shown that neither the analyte concentration nor the period of fiber exposure has an effect on the delta(13)C values. Finally, having verified that there are no matrix effects from the fermentation medium, it is reported for the first time that flavor compounds can be extracted directly from culture supernatant by SPME and their delta(13)C values can be obtained by GC-C-IRMS.     

Headspace solid phase microextraction (SPME) analysis of flavor compounds in wines. Effect of the matrix volatile composition in the relative response factors in a wine model.

The application of headspace solid phase microextraction (SPME) for flavor analysis has been studied. Headspace SPME sampling was tested for nine common wine flavor compounds in 10% (v/v) aqueous ethanol: linalool, nerol, geraniol, 3-methyl-1-butanol, hexanol, 2-phenylethanol, ethyl hexanoate, ethyl octanoate, and ethyl decanoate. The chemical groups (monoterpenoids, aliphatic and aromatic alcohols, and esters) showed specific behavior in SPME analysis. SPME sampling parameters were optimized for these components. Relative response factors (RRFs), which establish the relationship between the concentration of the compound in the matrix liquid solution and the GC peak area, were estimated for all compounds. Log(10)(RRF) varied from 0 (3-methyl-1-butanol) to 3 (ethyl decanoate), according to their molecular weight. Quantification by SPME was shown to be highly dependent on the matrix composition; the compounds with higher RRF were the less affected. As a consequence, the data obtained with this methodology should be used taking into consideration these limitations, as shown in the analysis of four monovarietal Bairrada white wines (Arinto, Bical, Cerceal, and Maria Gomes).     

Headspace solid-phase microextraction use for the characterization of volatile compounds in vegetable oils of different sensory quality

Headspace solid-phase microextraction (HS-SPME) was used to isolate the volatile compounds, which are formed during peroxidation of fatty acids in vegetable oils. Isolated compounds were characterized by GC-MS and quantified using GC with FID detection. Four fibers for HS-SPME method development were tested, and the divinylbenzene/carboxene/PDMS fiber was selected as providing the best detection of analyzed compounds. Extraction curves, limits of detection, repeatability, and linearity were investigated for 14 aldehydes, ketones, hydrocarbons, and alcohols being products of fatty acids autoxidation. Limits of detection for 11 of these were below 1 microg/L. For quantitative purposes, to minimize the influence of temperature on hydroperoxide formation and the changes in the volatiles profile of the extracts, sampling was performed at 20 degrees C. For compound characterization by GC-MS, sampling temperature of 50 degrees C was applied. The developed method was applied to the analysis of refined and cold-pressed rapeseed oil stored at 60 degrees C for 10 days, and for 10 different vegetable oils of various degree of peroxidation. All samples were subjected to sensory analysis. The results of PCA sensory analysis were related to the amount of volatile compounds isolated by SPME method. In cases where the amount of compounds was highest, the samples were perceived as the worst, whereas those with low levels of volatile compounds were the most desired ones according to sensory evaluation. The relation was observed for both total volatiles, quantified C5-C9 aldehydes, and 14 compounds selected in method development. SPME revealed to be a rapid and sensitive method for the extraction and quantitation of trace volatile compounds from plant oils even at ambient temperature.     

Direct Extraction of Volatiles of Rice During Cooking Using Solid-Phase Microextraction

An apparatus that allows extraction and enrichment of flavor volatiles of rice during cooking using solid-phase microextraction (SPME) was designed and tested in the Japanese rice cultivar Akitakomachi. Because it is a solvent-free technique, no solvent contaminants were extracted during sampling. This technique enables one to place the fiber of SPME in the effluent of the flavor volatiles of the rice during cooking and it can also be used for simultaneous extraction of those volatiles in the course of the cooking process. Therefore, variations in the composition and amount of volatile compounds of rice during cooking can be determined. The overall flavor volatiles of rice during cooking have been analyzed by using this SPME method. Compounds that have been previously highlighted as flavor volatile markers, such as volatiles from oxidative degradation of lipids, products from thermal decomposition, and fatty acids existing in rice, were extracted directly by SPME in conjunction with this apparatus.     

Solid-phase microextraction (SPME) technique for measurement of generation of fresh cucumber flavor compounds

Investigations were carried out to determine whether flavor compounds characteristic for fresh cucumbers could be rapidly determined using a solid-phase microextraction (SPME) dynamic headspace sampling method combined with gas chromatography and flame ionization detection. Cucumbers were sampled, during blending, for fresh cucumber flavor compounds (E,Z)-2,6-nonadienal and (E)-2-nonenal. The GC was such that the two target compounds were separated and baseline-resolved. Relative standard deviations for analysis of both (E,Z)-2,6-nonadienal and (E)-2-nonenal using this SPME sampling method were +/-10%. Utility of the analytical method was demonstrated by determining the effect of heat treatments on the ability of cucumbers to produce these flavor impact compounds.     

Solid-phase microextraction method development for headspace analysis of volatile flavor compounds

Solid-phase microextraction (SPME) fibers were evaluated for their ability to adsorb volatile flavor compounds under various conditions with coffee and aqueous flavored solutions. Experiments comparing different fibers showed that poly(dimethylsiloxane)/divinylbenzene had the highest overall sensitivity. Carboxen/poly(dimethylsiloxane) was the most sensitive to small molecules and acids. As the concentrations of compounds increased, the quantitative linear range was exceeded as shown by competition effects with 2-isobutyl-3-methoxypyrazine at concentrations above 1 ppm. A method based on a short-time sampling of the headspace (1 min) was shown to better represent the equilibrium headspace concentration. Analysis of coffee brew with a 1-min headspace adsorption time was verified to be within the linear range for most compounds and thus appropriate for relative headspace quantification. Absolute quantification of volatiles, using isotope dilution assays (IDA), is not subject to biases caused by excess compound concentrations or complex matrices. The degradation of coffee aroma volatiles during storage was followed by relative headspace measurements and absolute quantifications. Both methods gave similar values for 3-methylbutanal, 4-ethylguaiacol, and 2,3-pentanedione. Acetic acid, however, gave higher values during storage upon relative headspace measurements due to concurrent pH decreases that were not seen with IDA.     

Analysis of terpenoids from hemlock (Tsuga) species by solid-phase microextraction/gas chromatography/ion-trap mass spectrometry

A sampling method for determining the volatile terpenoid composition from single needles of seven Tsuga species was developed using headspace solid-phase microextraction (SPME). A reproducible sampling method for the volatile components was generated by examination of sample storage, method of needle cutting, and headspace sampling duration. Following SPME collection of the volatile compounds from the seven Tsuga species, gas chromatography/ion-trap mass spectrometry was used to identify 51 terpenoids present in the needle headspace. A semiquantitative method was devised to express individual terpenoid amounts as a percentage of all of the identified peaks in the chromatogram. The semiquantitative results permitted facile interspecies comparison using principal component analysis. Two components were able to account for 90% of the variance and were interpreted as a "species" component and a "resistance/susceptibility" component. Three interspecies groupings were evident from the principal component analysis: (1) Tsuga canadensis and Tsuga caroliniana; (2) Tsuga chinesnsis, Tsuga diversifolia, Tsuga heterophylla, and Tsuga sieboldii; and (3) Tsuga mertensiana. The finding that T. mertensiana was grouped alone and far removed from the other species adds to the morphological evidence that this species should be segregated from other Tsuga.     

New device for direct extraction of volatiles in solid samples using SPME.

A new device that allows extraction of volatiles from solid materials by SPME, avoiding preparation of the sample, was designed and tested in two different food products. Volatiles from dry-cured ham and canned liver sausage were analyzed by headspace SPME (HS SPME) and by using a new device that protects the SPME fiber in the core of the solid material. Volatile profiles generated by using both methods of extraction were very similar in both products. Compounds that have been previously highlighted as quality markers, such as products from oxidative degradation of lipids, products from Strecker degradation of amino acids, or terpenes, were satisfactorily extracted by SPME coupled to the device for direct extraction. In addition, by using this method no laboratory contaminants were extracted, whereas some major laboratory solvents were presented in the chromatogram using the HS SPME method. However, coefficients of variation were higher when performing the direct sampling procedure. This new device appears to have potential as a simple method for extracting volatiles in solid materials while at the same time avoiding taking samples.     

Sample extraction method combining micellar extraction-SPME and HPLC for the determination of organochlorine pesticides in agricultural soils

A method for the determination of organochlorine pesticides in soil samples combining microwave assisted micellar extraction (MAME) with solid-phase microextraction (SPME) and high-performance liquid chromatography-UV has been developed. A mixture of two nonionic surfactants (polyoxyethylene 10 lauryl ether and polyoxyethylene 10 stearyl ether) was used for the extraction of pesticides from agricultural soils, and different types of SPME fibers were compared. The different parameters which affect extraction efficiency in the SPME procedure were optimized such as extraction time and temperature. The method developed involves extraction and preconcentration for the target analytes in soil samples. The analytical parameters were also studied and good recoveries obtained, RSD being lower than 10% and detection limits ranging between 36 and 164 ng g(-1) for the pesticides studied. The proposed method was successfully applied to the determination of some organochlorine pesticides in several kinds of agricultural soil samples with different characteristics.     

Ethanol-modified subcritical water extraction combined with solid-phase microextraction for determining atrazine in beef kidney

The determination of the levels of pesticides in food products has prompted the development of sensitive and rapid methods of analysis that are solvent-free or utilize solvents that are benign to the environment and laboratory worker. In this study we have developed a novel extraction method that utilizes ethanol-modified subcritical water in combination with solid-phase microextraction (SPME) for the removal of atrazine from beef kidney. In situ sample cleanup was achieved using the technique of matrix solid-phase dispersion. A cross-linked polymer, XAD-7 HP, was utilized as a dispersing material for kidney samples. Subcritical water extractions were performed with a pressurized solvent extraction unit at 100 degrees C and 50 atm. Experimental parameters investigated were the volume of solvent and amount of modifier required for the complete extraction of atrazine and optimization of the extraction time. It was determined that 30% ethanol in water (v/v) is adequate for the complete extraction of atrazine. A Carbowax-divinylbenzene SPME fiber was used to sample the aqueous extracts. Analysis of the fiber contents was by ion-trap GC/MS utilizing the single ion mode. The total time of analysis for a single kidney sample is 90 min. The average percent recoveries from samples spiked to the concentrations of 2 and 0.2 microg/g were 104 and 111, respectively. The average relative standard deviations were 10 and 9, respectively. The method limit of detection for beef kidney spiked with atrazine was found to be 20 ng/g of sample.     

Composition of phenolic compounds and antioxidant activity of commercial aqueous smoke flavorings

The antioxidant activity of 12 aqueous commercial smoke flavorings used in the food industry was determined by two methods: bleaching of the carotenoid crocin and scavenging of the DPPH radical. The reaction with the DPPH radical was evaluated by calculating the effective concentration (EC50) and the antiradical efficiency (AE). A gas chromatography-mass spectrometry method was, moreover, used for the determination of 2-methoxyphenols, 2,6-dimethoxyphenols, and dihydroxybenzenes. The methoxyphenols were extracted from the aqueous smoke by dichloromethane, and also the residue aqueous phase was analyzed to determine the more water-soluble dihydroxybenzenes. The recovery and the repeatability of the method are reported. The total phenolic concentrations of the smoke flavorings showed a wide range, from about 1000 to 25000 mg/kg. Considering the three classes of compounds, the concentrations were about 300-3000 mg/kg for the 2-methoxyphenols, 200-11000 mg/kg for the 2,6-dimethoxyphenols, and 140-10000 mg/kg for the dihydroxybenzenes. The range of the antioxidant activities of the smoke flavorings was wide, reflecting the wide range of the phenolic concentrations. Good correlations were obtained between the total phenolic concentration and the antioxidant activities determined by both the DPPH and crocin assays.     

Quantitation of (R)- and (S)-linalool in beer using solid phase microextraction (SPME) in combination with a stable isotope dilution assay (SIDA)

A stable isotope dilution assay (SIDA) was developed for the quantitation of both linalool enantiomers using synthesized [2H(2)]R/S-linalool as the internal standard. For enrichment of the target compound from beer, a solid phase microextraction method (SPME) was developed. In comparison to the more time-consuming extraction/distillation cleanup of the beer samples, the results obtained by SPME/SIDA were very similar, even under nonequilibration conditions. Analysis of five different types of beer showed significant differences in the linalool concentrations, which were clearly correlated with the intensity of the hoppy aroma note as evaluated by a sensory panel. In addition, significant differences in the R/S ratios were measured in the beers. The SPME/SIDA yielded exact data independently from headspace sampling parameters, such as exposure time or ionic strength of the solution.     

Identification of the botanical origin of raw spirits produced from rye, potato, and corn based on volatile compounds analysis using a SPME-MS method

Determination of the botanical origin of raw spirit used for alcoholic beverage production is of great importance for rectifying units, control laboratories, and proper product labeling. Raw spirit samples (138) produced from rye, corn, and potato were analyzed using a solid phase microextraction-mass spectrometry (SPME-MS) method, which involved volatiles preconcentration by SPME with subsequent volatile fraction characterization by MS without particular compounds separation by GC. Obtained data were treated using principal component analysis and linear discriminant analysis (LDA) to test the possibility of sample classification. SPME sampling conditions allowed rapid extraction in 2 min at 50 °C using a carboxen/divinylbenzene/polydimethylsiloxane fiber, followed by rapid MS analysis. Use of LDA made possible the classification of raw spirits based on the material they were produced from. The classification ability of the developed SPME-MS method was 100%, whereas its prediction ability was 96%.     

Carbohydrate and nitrogenated compounds in liquid smoke flavorings

Commercial smoke flavorings were extracted with dichloromethane and the remaining aqueous phase was evaporated at room temperature; the residues obtained were dissolved in methanol and studied by gas chromatography/mass spectrometry. The composition of these residues was totally different from that of the dichloromethane extracts, constituting a small number of compounds that were also detected in the dichloromethane extract, as well as a large number of compounds not described before as components of either smoke for food smoking or smoke flavorings. Among those compounds not previously described there are some furan, pyran, and phenolic derivatives, as well as some pyridine and carbohydrate derivatives. The main component of these fractions is 1,6-anhydro-beta-D-glucopyranose, or levoglucosan. Likewise, aqueous residues of liquid smoke flavorings, prepared at a laboratory scale from beech, vine shoots, thyme, and sage, were studied in the same way. These contained compounds of the same groups cited above, but showed clear differences. The aqueous residue of beech smoke flavoring was the most similar to that of the commercial smoke flavorings. The aqueous residues of vine shoots, thyme, and sage smoke flavorings contained a lower number of furan, pyran, and carbohydrate derivatives and a higher number of nitrogenated derivatives. Instead of levoglucosan, the main component was an unidentified compound, present in all samples, included in the carbohydrate derivatives group. In the samples studied, the influence of the vegetal source on the composition of the aqueous fraction has been shown. In the future, attention must be paid to the functionality of these smoke components.     

Bioactivity of Backhousia citriodora: antibacterial and antifungal activity

Backhousia citriodora products are used as bushfoods and flavorings and by the aromatherapy industry. The antimicrobial activity of 4 samples of B. citriodora oil, leaf paste, commercial tea (0.2 and 0.02 g/mL), and hydrosol (aqueous distillate) were tested against 13 bacteria and 8 fungi. Little or no activity was found to be associated with the leaf tea and hydrosol, respectively. Leaf paste displayed antimicrobial activity against 7 bacteria including Clostridium perfringens, Pseudomonas aeruginosa, and a hospital isolate of methicillin resistant Staphylococcus aureus (MRSA). The 4 essential oils were found to be effective antibacterial and antifungal agents; however, variation was apparent between oils that did not correlate with citral content. The antimicrobial activity of B. citriodoraessential oils was found to be greater than that of citral alone and often superior to Melaleuca alternifolia essential oil. B. citriodora has significant antimicrobial activity that has potential as an antiseptic or surface disinfectant or for inclusion in foods as a natural antimicrobial agent.