Preparative HPLC method for the purification of sulforaphane and sulforaphane nitrile from Brassica oleracea

An extraction and preparative HPLC method has been devised to simultaneously purify sulforaphane and sulforaphane nitrile from the seed of Brassica oleracea var. italica cv. Brigadier. The seed was defatted with hexane, dried, and hydrolyzed in deionized water (1:9) for 8 h. The hydrolyzed seed meal was salted and extracted with methylene chloride. The dried residue was redissolved in a 5% acetonitrile solution and washed with excess hexane to remove nonpolar contaminants. The aqueous phase was filtered through a 0.22-microm cellulose filter and separated by HPLC using a Waters Prep Nova-Pak HR C-18 reverse-phase column. Refractive index was used to detect sulforaphane nitrile, and absorbance at 254 nm was used to detect sulforaphane. Peak identification was confirmed using gas chromatography and electron-impact mass spectrometry. Each kilogram of extracted seed yielded approximately 4.8 g of sulforaphane and 3.8 g of sulforaphane nitrile. Standard curves were developed using the purified compounds to allow quantification of sulforaphane and sulforaphane nitrile in broccoli tissue using a rapid GC method. The methodology was used to compare sulforaphane and sulforaphane nitrile content of autolyzed samples of several broccoli varieties.     

Evaporative light-scattering analysis of sulforaphane in broccoli samples: Quality of broccoli products regarding sulforaphane contents

Broccoli sulforaphane has received attention as a possible anticarcinogen. Sulforaphane analysis is difficult due to the lack of a chromophore for spectrometric detection. Hence, we developed a method for determining sulforaphane by using high-performance liquid chromatography (HPLC) coupled with an evaporative light-scattering detector (ELSD). Sulforaphane was extracted from acid-hydrolyzed broccoli samples, followed by solid-phase extraction and reversed-phase HPLC. Sulforaphane was detected by ELSD and concurrently identified by electrospray ionization time-of-flight mass spectrometry. The recovery of sulforaphane from broccoli samples was above 95%. The detection limit was 0.5 mug. The present method was sensitive enough to determine sulforaphane in mature broccoli, broccoli sprouts, and commercial broccoli products. Sulforaphane concentration in broccoli sprout (1153 mg/100 g dry weight) was about 10 times higher than that of mature broccoli (44-171 mg/100 g dry weight). Therefore, the broccoli sprout is recommended as a source of sulforaphane-rich products. In contrast, we found that sulforaphane could not be detected in most of broccoli products, suggesting present commercial broccoli products having low quality.     

Multiresidue HPLC methods for phenyl urea herbicides in water

High-performance liquid chromatography (HPLC) methods for the determination of phenyl urea herbicides in water are described. The target compounds include chlortoluron, diuron, fluometuron, isoproturon, linuron, metobromuron, metoxuron, monuron, neburon, and siduron. Water was subjected to solid phase extraction (SPE) using either automated SPE with 47 mm C(18) Empore disks or on-line precolumn concentration. Herbicides were separated on a C(18) reversed phase column with an acetonitile-water gradient and were detected with either a diode array detector (DAD) or a postcolumn photolysis and derivatization (PPD) detector system. Photolysis converted the phenyl ureas to monoalkylamines that were derivatized to fluorescent isoindoles by reaction with o-phthalaldehyde and 2-mercaptoethanol. The DAD monitoring at 245 nm was linear over three decades with instrument detection limits of approximately 0.01 mg/L. SPE efficiency was between 48 and 70% in laboratory reagent water, but use of the internal standard quantitation method improved accuracy. High total dissolved solids and total organic carbon values in surface water improved recoveries relative to laboratory reagent water for all of the phenyl ureas. In Colorado River water spiked at 1 or 50 microg/L, mean recoveries ranged from 74 to 104%. Method detection limits (MDLs) ranged from 4 to 40 ng/L (parts per trillion) with the DAD instrument. PPD detection was highly specific but resulted in a slight loss in chromatographic efficiency and average MDLs approximately 5 times higher using a single set of detection conditions. The study indicates that methods based on SPE followed by HPLC with diode array or PPD detection have practical utility for trace analysis of phenyl ureas in drinking water or surface waters.     

An analytical method for the simultaneous determination of butachlor and benoxacor in wheat and soil

Butachlor is a chloroacetanilide herbicide successfully employed in weeding some important crops, and benoxacor is a safening compound able to induce the enzymatic mechanism of chloroacetanilide detoxification in plants. A practical method for a simultaneous detection of butachlor and benoxacor residues in wheat and in soil is described. The procedure can be performed by GC and HPLC. They were extracted with methanol and cleaned up by solid phase extraction (SPE). The analytes were satisfactorily separated via both GC and HPLC techniques, and no interferences were observed coming from plant or soil matrixes or reagents. The limit of quantitation was found to be 5.0 ng by GC and 20.0 ng by HPLC for butachlor and 2.5 ng by GC and 15.0 ng by HPLC for benoxacor. Butachlor recovery tests ranged from 85.4% to 91.7% in wheat shoots and 84.0% to 93.2% in soil; benoxacor recovery tests ranged from 86.5% to 90.8% in wheat shoots and 85.7% to 90.7% in soil. The reproducibility and the accuracy make this method a selective and sensitive tool for routine analyses.     

Determination of organochlorine and organophosphorus pesticide residues in eggs using a solid phase extraction cleanup

A multiresidue solid phase extraction (SPE) method for the isolation and subsequent gas chromatographic determination of nonpolar organochlorine and polar organophosphorus pesticide residues in eggs is described. The method uses an acetonitrile extraction followed by an SPE cleanup using graphitized carbon black and aminopropyl SPE columns. Organophosphorus pesticides are determined by gas chromatography with flame photometric detection. After further cleanup of the extract using Florisil SPE columns, organochlorine pesticides are determined by gas chromatography with electron capture detection. Studies were performed using eggs containing both fortified and incurred pesticide residues. The average recoveries were 86-108% for 8 fortified organochlorine pesticide residues and 61-149% for 28 fortified organophosphorus pesticide residues.     

固相萃取-高效液相色谱法测定有机肥中四环素类抗生素药物残留

建立了固相萃取-高效液相色谱(SPE-HPLC)法测定有机肥中土霉素(OTC)、四环素(TC)和金霉素(CTC)3种四环素类抗生素残留的方法。肥料样品采用甲醇、EDTA和McIlvaine缓冲液的混合液(pH=7.2)为提取液,用强阴离子交换柱(SAX)-亲水亲脂萃取柱(HLB)串联进行纯化和富集。采用甲醇-乙腈-0.01mol/L草酸溶液为流动相,进行HPLC分析。3种抗生素的线性范围为0.10～20 mg/L,OTC、TC和CTC的检测限分别为0.03、0.03和0.05 mg/L。不同添加水平的样品加标回收率为64%～86%,RSD在4.14%～8.16%之间。该方法测定了上海市场上40种肥料,发现部分样品有四环素类抗生素的残留物。     

Determination of phenols, flavones, and lignans in virgin olive oils by solid-phase extraction and high-performance liquid chromatography with diode array ultraviolet detection

A simple analytical method for the quantitative determination of phenols, flavones, and lignans in virgin olive oils was developed. The polar fraction was isolated from small amounts of oil sample (2.5 g) by solid-phase extraction (SPE) using diol-phase cartridges, and the extract was analyzed by reversed-phase HPLC coupled with diode array UV detection. Chromatographic separation of pinoresinol, cinnamic acid, and 1-acetoxypinoresinol was achieved. Repeatability (RSD < 6.5%), recovery (> 90%), and response factors for each identified component were determined. SPE on amino-phase cartridges was used for isolating acidic phenols and as an aid for phenol identification. For the first time, 2-(4-hydroxyphenyl)ethyl acetate was detected in olive oils. The aldehydic structure of the ligstroside aglycon was confirmed by NMR spectroscopy. The colorimetric determination of total o-diphenolic compounds by reaction with molybdate was consistent with their HPLC determination. Differences between results obtained by liquid-liquid extraction and SPE were not statistically significant.     

Application of high-speed countercurrent chromatography for the isolation of sulforaphane from broccoli seed meal

In order to produce large amounts of pure sulforaphane for research purposes, a novel method using high-speed countercurrent chromatography (HSCCC) was developed. Without any initial cleanup steps, sulforaphane was successfully purified from the ethyl acetate extract of the broccoli seed meal by HSCCC. The separation was performed with two-phase solvent systems: n-hexane/ethyl acetate/methanol/water (1:5:1:5, v/v/v/v). From 850 mg of the ethyl acetate extract, 186 mg of sulforaphane was isolated with the solvent system. The purified compound was over 97% purity as determined by HPLC analysis, and the chemical structure was confirmed by MS and (1)H and (13)C NMR.     

Determination of limonin D-ring lactone hydrolase activity by solid phase extraction with indirect fluorescence detection

A method for the evaluation of limonin D-ring lactone hydrolase activity is described. The method utilizes solid phase extraction (SPE) for the isolation of limonin A-ring limonoate (LARL), which is subsequently converted to limonin and quantitated by fluorescence. The fluorescence method is capable of quantifying the formation of LARL in concentrations as low as 75 ng and is applicable to both purified and crude enzyme preparations. The coupling of SPE with fluorescence detection allows for the simple and rapid analysis of samples.     

Determination of carbofuran and its metabolites in rice paddy water by using solid phase extraction and liquid chromatography

A procedure for the determination of carbofuran and its metabolites (carbamate and phenolic) in rice paddy water is described. Water samples are concentrated on a C-18 solid phase extraction (SPE) column and eluted with methanol-water. The eluate is analyzed by reverse-phase liquid chromatography (LC) and measured by a wavelength programmable ultraviolet (UV) detector. The limit of detection for the method is 0.4 micrograms/L. Recovery studies were carried out at levels ranging from 1 to 15 micrograms/L in both rice paddy water and distilled water; recoveries ranged from 85.9 to 112.9%.     

Determination of aflatoxin M1 in milk and milk powder using high-flow solid-phase extraction and liquid chromatography-tandem mass spectrometry

Animal feeds occasionally have some degree of contamination by Aspergillus spp. Even pasteurized milk at times contains the toxic liver carcinogen aflatoxin M1 (AFM1). Confirmation of its presence is now done with solid-phase extraction (SPE) and high-performance liquid chromatography (HPLC)-fluorescence, using a small enough sample that SPE time is reasonable. In this study 200 mL of milk was extracted using a C18 disk at a flow rate of approximately 100 mL/min and AFM1 quantified by HPLC-tandem mass spectrometry with negative electrospray ionization. The effectiveness and cleanup efficacy of immunoaffinity columns (IAC) was compared with that of Mycosep multifunctional cleanup columns (MFC). Average recovery and detection limits of whole milk and low-fat milk cleaned up by IAC were significantly superior to those obtained with the MFC (78-87% and 0.59-0.66 ng/L, respectively). The new procedure improves extraction speed, sensitivity, and specificity.     

Monoclonal enzyme immunoassay for the analysis of carbaryl in fruits and vegetables without sample cleanup

The N-methylcarbamate pesticide carbaryl is one of the most important insecticides used worldwide. In the present work, the validation of a monoclonal antibody-based enzyme immunoassay (ELISA) for the determination of this compound in fruits and vegetables is described. The immunoassay is a competitive heterologous ELISA in the antibody-coated format, with an I(50) value for standards in buffer of 101.0 +/- 26.9 ng/L and with a dynamic range between 31.6 and 364.0 ng/L. For recovery studies, peppers, cucumbers, strawberries, tomatoes, potatoes, oranges, and apples were spiked with carbaryl at 10, 50, and 200 ppb. After liquid extraction, analyses were performed by ELISA on both extracts purified on solid-phase extraction (SPE) columns and crude, nonpurified extracts. Depending on the crop and the fortification level, recoveries in the 59.0--120.0% range were obtained for purified samples and in the 70.0--137.7% range for crude extracts. The carbaryl immunoassay performance was further validated with respect to high-performance liquid chromatography (HPLC) with postcolumn derivatization and fluorescence detection (EPA Method 531.1). Samples were spiked with carbaryl at several concentrations and analyzed as blind samples by ELISA and HPLC after SPE cleanup. The correlation between methods was excellent (y = 1.04x + 0.71, r(2) = 0.992, n = 33), with HPLC being more precise than ELISA (mean coefficients of variation of 5.2 and 12.0%, respectively). The immunoassay was then applied to the analysis of nonpurified extracts of the same samples. Results also compared very well with those obtained by HPLC on purified samples (y = 1.28x - 0.59, r(2) = 0.987, n = 33) while maintaining similar precision. Therefore, the developed immunoassay is a suitable method for the quantitative and reliable determination of carbaryl in fruits and vegetables even without sample cleanup, which saves time and money and considerably increases sample throughput.     

Validation of a monoclonal enzyme immunoassay for the determination of carbofuran in fruits and vegetables

The N-methylcarbamate pesticide carbofuran is a very important insecticide used worldwide. In the present work, the validation of a monoclonal antibody-based enzyme immunoassay (ELISA) to determine this compound in fruits and vegetables is described. The immunoassay is a competitive heterologous ELISA in the antibody-coated format, with an I(50) value for standards in buffer of 740 ng/L and with a dynamic range between 200 and 3100 ng/L. For recovery studies, peppers, cucumbers, strawberries, tomatoes, potatoes, oranges, and apples were spiked with carbofuran at 10, 50, and 200 ppb. After liquid extraction, analyses were performed by ELISA on extracts purified on solid-phase extraction (SPE) columns and crude, nonpurified extracts. Depending on the crop, mean recoveries in the 43.9--90.7% range were obtained for purified samples and in the 90.1--121.6% range for crude extracts. The carbofuran immunoassay performance was further validated with respect to high-performance liquid chromatography (HPLC) with postcolumn derivatization and fluorescence detection (EPA Method 531.1). Samples were spiked with carbofuran at several concentrations and analyzed as blind samples by ELISA and HPLC after SPE cleanup. The correlation between methods was very good (y = 0.90x + 2.66, r(2)() = 0.958, n = 25), with HPLC being more precise than ELISA (mean coefficients of variation of 4.1 and 11.5%, respectively). The immunoassay was then applied to the analysis of nonpurified extracts of the same samples. Results also compared very well with those obtained by HPLC on purified samples (y = 1.02x + 10.44, r(2)() = 0.933, n = 29). Therefore, the developed immunoassay is a suitable method for the quantitative and reliable determination of carbofuran in fruits and vegetables even without sample cleanup, which saves time and money and considerably increases the sample throughput.     

Analysis of coffee for the presence of acrylamide by LC-MS/MS

A variety of popular instant, ground, and brewed coffees were analyzed using a modified liquid chromatography-tandem mass spectrometry (LC-MS/MS) method specifically developed for the determination of acrylamide in foods. Coffee test portions were spiked with 13C3-labeled acrylamide as an internal standard prior to their extraction and cleanup. Ground coffees (1 g) and instant coffees (0.5 g) were extracted by shaking with 9 mL of water for 20 min. Brewed coffee test portions (9 mL) were taken through the cleanup procedure without further dilution with extraction solvent. Coffee test portions were cleaned up by passing 1.5 mL first through an Oasis HLB (hydrophilic/lipophilic copolymer sorbent) solid phase extraction (SPE) cartridge and then a Bond Elut-Accucat (cation and anion exchange sorbent) SPE cartridge. The cleaned up extracts were analyzed by positive ion electrospray LC-MS/MS. The MS/MS data was used to detect, confirm, and quantitate acrylamide. The limit of quantitation of the method was 10 ng/g for ground and instant coffees and 1.0 ng/mL for brewed coffee. The levels of acrylamide ranged from 45 to 374 ng/g in unbrewed coffee grounds, from 172 to 539 ng/g in instant coffee crystals, and from 6 to 16 ng/mL in brewed coffee.     

Rugged LC-MS/MS survey analysis for acrylamide in foods

The described liquid chromatography-tandem mass spectrometry (LC-MS/MS) method for the detection of acrylamide in food entails aqueous room temperature extraction, SPE cleanup, and analysis by LC-MS/MS. The method is applicable to a wide variety of foods. [(13)C(3)]acrylamide is the internal standard. The limit of quantitation is 10 ppb (microg/kg). Data were obtained in duplicate from >450 products representing >35 different food types. The variability in analyte levels in certain food types suggests that it may be possible to reduce acrylamide levels in those foods.     

Determination of vitamin D3 in liquid multivitamin preparation, using reverse phase, solid phase extraction liquid chromatography

A method is described for the determination of vitamin D3 in a liquid multivitamin preparation by liquid chromatography. Samples are purified on a disposable reverse phase extraction (SPE) column with a mobile phase of methanol-2-propanol (97 + 3) and are analyzed on a Zorbax ODS (5 micron) column with an acetonitrile-2-propanol-water (90 + 8 + 2) solvent system. Vitamin D3 is completely resolved from other interfering compounds within approximately 21 min and is detected with a UV detector at 254 nm. A mean of 98.5% of theory with a coefficient of variation of 3.8% was found for determination of vitamin D3 in a commercial preparation.     

Advanced solid phase extraction using molecularly imprinted polymers for the determination of quercetin in red wine

Solid phase extraction (SPE) based on molecularly imprinted polymers (MIPs) is a novel approach for sample preparation and preconcentration, gaining increased interest in the fields of environmental, clinical, and food analysis. The first application combining MIPs with SPE for advanced beverage analysis is reported. MIPs for the flavonoid quercetin have been generated, using quercetin as a template molecule in a self-assembly approach and yielding imprinting of 1% of the used template. The MIP achieved a capacity of 0.4 g quercetin per gram polymer and a recovery rate of 98.2%. The application of these synthetic receptors as SPE material for the selective extraction and preconcentration of quercetin from synthetic and red wine samples was investigated. Red wine samples from a French Merlot were directly applied onto the SPE cartridge. The collected fractions were analyzed by high-pressure liquid chromatography. For verification of the obtained results, a similarly prepared nonimprinted polymer and a classical octadecyl silane reversed-phase cartridge were applied as the SPE matrix during control experiments. The MIP enabled the selective extraction of quercetin from a complex matrix, such as red wine, spiked with 8.8 mg per liter quercetin, demonstrating the potential of molecularly imprinted solid phase extraction for rapid, selective, and cost-effective sample pretreatment.     

Multiresidue method for determination of 35 pesticides in virgin olive oil by using liquid-liquid extraction techniques coupled with solid-phase extraction clean up and gas chromatography with nitrogen phosphorus detection and electron capture detection

A method for the multiresidue determination of 35 pesticides (30 insecticides and five herbicides) in olive oil by gas chromatography (GC) is described. Three liquid-liquid extraction (LLE) procedures based on (i) partition of pesticides between acetonitrile (ACN) and oil solution in n-hexane, (ii) partition of pesticides between saturated ACN with n-hexane and oil solution in n-hexane saturated with ACN, and (iii) partition of pesticides between ACN and oil were tested for the optimization of the highest pesticide recoveries with the lowest oil residue in the final extracts. Experimental tests were preformed in order to study the efficiency of different clean up procedures with N-Alumina, Florisil, C18, and ENVI-Carb solid-phase extraction (SPE) cartridges for the compounds analyzed by GC-nitrogen phosphorus detection. A second step of clean up was also performed for the compounds analyzed by GC-electron capture detection (ECD), by using phenyl-bonded silica (Ph), diol-bonded silica (Diol), cyanopropyl-bonded silica (CN), and amino propyl-bonded silica (NH2) SPE cartridges. LLE of the oil solution in hexane with ACN followed by an ENVI-Carb SPE clean up of the extract gave the best results for all target compounds. The ACN extract was additionally cleaned through a Diol-SPE cartridge for the determination of pesticides analyzed mainly by GC-ECD. Pesticide recoveries form virgin olive oil spiked with 20, 100, and 500 microg/kg concentrations of pesticides ranged from 70.9 to 107.4%. The proposed method featured good sensitivity, pesticide quantification limits were low enough, and the precision, expressed as relative standard deviation, ranged from 2.4 to 12.0%. The proposed method was applied successfully for the residue determination of the selected pesticides in commercial olive oil samples.     

Simultaneous determination of neonicotinoid insecticides in agricultural samples by solid-phase extraction cleanup and liquid chromatography equipped with diode-array detection

Effective sample pretreatment procedures based on solid-phase extraction (SPE) for multiresidue determination of seven neonicotinoid insecticides in agricultural products were investigated. After extraction with acetone and concentration, the insecticides in aqueous sample extracts were transferred into organic solvent phases with a Chem Elut SPE cartridge. Finally, the eluate from the cartridge was cleaned up with a SPE cartridge packed with graphitized carbon black and aminopropyl silica gel, which showed a higher cleanup efficiency than the classical silica gel SPE cartridge. Seven insecticides were separated on a reversed-phase C18 column and a gradient system of methanol and phosphate solution based on high-performance liquid chromatography. The established multiresidue determination has been applied to several artificially spiked agricultural samples, with the result that the average recoveries were excellent, with the exception of nitenpyram. The limit of detection of the method ranged from 0.01 to 0.03 mg/kg for the insecticides.     

Quantitative determination of pyrethroids, pyrethrins, and piperonyl butoxide in surface water by high-resolution gas chromatography/high-resolution mass spectrometry

A new method for determination of pyrethroids, pyrethrins, and piperonyl butoxide (PBO) by high-resolution gas chromatography/high-resolution mass spectrometry (HRGC/HRMS) was developed for surface water samples. The method is based on sampling 100 L of ambient surface water with a solid phase extraction (SPE) technique that uses both wound glass fiber filters for collecting the particulate-associated chemicals and XAD-2 resin for collecting the dissolved chemicals. The method detection limits of the analytes ranged from 0.58 to 8.16 ng/sample, which is equivalent to a detection limit range of 0.0058-0.082 ng/L for a 100 L water sample collected by the SPE technique. The SPE when coupled with HRGC/HRMS was a suitable match for detecting these chemicals at subnanogram per liter ranges that are toxicologically significant to aquatic organisms. To confirm the utility of this method for environmental applications, pyrethroids and PBO were found at subnanogram per liter concentrations in surface water samples collected from five tributaries (primarily urban creeks) of the San Francisco Bay, California.