Deficit irrigation and nitrogen effects on seed cotton yield, water productivity and yield response factor in shallow soils of semi-arid environment

A field experiment was conducted for 2 years to investigate the effects of deficit irrigation, nitrogen and plant growth minerals on seed cotton yield, water productivity and yield response factor. The treatment comprises six levels of deficit irrigation (Etc 1.0, 0.9, 0.8, 0.7, 0.6 and 0.5) and four levels of nitrogen (80, 120, 160 and 200 kg N ha⁻¹). These were treatments superimposed with and without plant growth mineral spray. Furrow irrigation treatments were also kept. Cotton variety Ankur-651 Bt was grown during 2006 and 2007 cotton season. Drip irrigation at 1.0 Etc saved 26.9% water and produced 43.1% higher seed cotton yield over conventional furrow irrigation (1.0 Etc). Imposing irrigation deficit of 0.8 Etc caused significant reduction in seed cotton yield to the tune of 9.3% of the maximum yield. Further increase in deficit irrigation from 0.7 Etc to 0.5 Etc significantly decreased seed cotton yield over its subsequent higher irrigation level. Decline in the yield under deficit irrigation was associated with reduction in number of bolls plant⁻¹ and boll weight. Nitrogen at 200 kg ha⁻¹ significantly increased mean seed cotton yield by 36.3% over 80 kg N ha⁻¹. Seed cotton yield tended to increase linearly up to 200 kg N ha⁻¹ with drip Etc 0.8 to drip Etc 1.0. With drip Etc 0.6-0.5, N up to 160 kg ha⁻¹ provided the highest yield, thereafter it had declined. Foliar spray of plant growth mineral (PGM) brought about significant improvement in seed cotton yield by 14.1% over control. The water productivity ranged from 0.331 to 0.491 kg m⁻³ at different irrigation and N levels. On pooled basis, crop yield response factor of 0.87 was calculated at 20% irrigation deficit.     

Cotton yield and water use efficiency at various levels of water and N through drip irrigation under two methods of planting

The present investigation was undertaken to evaluate the effect of various levels of water and N application through drip irrigation on seed cotton yield and water use efficiency (WUE). In this experiment three levels of water (Epan 0.4, 0.3, and 0.2) and three levels of N (100, 75, and 50% of recommended N, 75 kg/ha) through drip were compared with check-basin method of irrigation under two methods of planting (normal sowing, NS; paired sowing, PS). The results revealed that when the same quantity of irrigation water and N was applied through drip irrigation system, it increased the seed cotton yield to 2144 from 1624 kg/ha (an increase of 32%) under check-basin method of irrigation. When the quantity of water through drip was reduced to 75%, the increase in seed cotton yield was 12%; however, when water was reduced to 50%, it resulted 2% lower yield than check-basin. The decrease in N through fertigation resulted in reduction in seed cotton yield at all the levels of water supply, but the magnitude of reduction was the highest at highest level of water supply. In paired sowing (PS), 20% higher seed cotton yield was obtained as compared with check-basin method under NS along with 50% saving of water. In paired sowing the sacrifice of 9% seed cotton yield as compared with NS resulted in saving of 50% water as well as the cost of laterals because there was one lateral for two paired rows. The WUE increased by 26% (22.1 from 17.6 kg/ha cm) in drip irrigation system when same quantity of water and N fertilizer was applied as compared with check-basin. WUE was not affected with quantity of water but decrease in rate of N caused a decrease in WUE at all the quantities of water applied. In general, WUE was higher in PS as compared with NS. The agronomic efficiency of nitrogen increased from 21.65 to 28.59 kg of seed cotton per kg of N applied when same quantity of water and N was applied through drip irrigation as compared with check-basin. However, decrease in quantity of water applied resulted in a decrease in agronomic efficiency of N but reverse was true for rates of N applied. When the same quantity of water and N was applied under both the methods of planting, PS produced 22% higher seed cotton yield and along with reduced cost owing to half the number of laterals required.     

Evapotranspiration and water use of full and deficit irrigated cotton in the Mediterranean environment in northern Syria

Cotton (Gossypium hirsutum L.) is the most important industrial and summer cash crop in Syria and many other countries in the arid areas but there are concerns about future production levels, given the high water requirements and the decline in water availability. Most farmers in Syria aim to maximize yield per unit of land regardless of the quantity of water applied. Water losses can be reduced and water productivity (yield per unit of water consumed) improved by applying deficit irrigation, but this requires a better understanding of crop response to various levels of water stress. This paper presents results from a 3-year study (2004-2006) conducted in northern Syria to quantify cotton yield response to different levels of water and fertilizer. The experiment included four irrigation levels and three levels of nitrogen (N) fertilizer under drip irrigation. The overall mean cotton (lint plus seed, or lintseed) yield was 2502 kg ha⁻¹, ranging from 1520 kg ha⁻¹ under 40% irrigation to 3460 kg ha⁻¹ under 100% irrigation. Mean water productivity (WP_ET) was 0.36 kg lintseed per m³ of crop actual evapotranspiration (ET_c), ranging from 0.32 kg m⁻³ under 40% irrigation to 0.39 kg m⁻³ under the 100% treatment. Results suggest that deficit irrigation does not improve biological water productivity of drip-irrigated cotton. Water and fertilizer levels (especially the former) have significant effects on yield, crop growth and WP_ET. Water, but not N level, has a highly significant effect on crop ET_c. The study provides production functions relating cotton yield to ET_c as well as soil water content at planting. These functions are useful for irrigation optimization and for forecasting the impact of water rationing and drought on regional water budgets and agricultural economies. The WP_ET values obtained in this study compare well with those reported from the southwestern USA, Argentina and other developed cotton producing regions. Most importantly, these WP_ET values are double the current values in Syria, suggesting that improved irrigation water and system management can improve WP_ET, and thus enhance conservation and sustainability in this water-scarce region.     

Different drip irrigation regimes affect cotton yield, water use efficiency and fiber quality in western Turkey

Decreasing in water availability for cotton production has forced researchers to focus on increasing water use efficiency by improving either new drought-tolerant cotton varieties or water management. A field trial was conducted to observe the effects of different drip irrigation regimes on water use efficiencies (WUE) and fiber quality parameters produced from N-84 cotton variety in the Aegean region of Turkey during 2004 and 2005. Treatments were designated as full irrigation (T₁₀₀, which received 100% of the soil water depletion) and those that received 75, 50 and 25% of the amount received by treatment T₁₀₀ on the same day (treatments T₇₅; T₅₀ and T₂₅, respectively). The average seasonal water use values ranged from 265 to 753 mm and the average seed cotton yield varied from 2550 to 5760 kg ha⁻¹. Largest average cotton yield was obtained from the full irrigation treatment (T₁₀₀). WUE ranged from 0.77 kg m⁻³ in the T₁₀₀ to 0.98 kg m⁻³ in the T₂₅ in 2004 growing season and ranged from 0.76 kg m⁻³ in the T₁₀₀ to 0.94 kg m⁻³ in the T₂₅ in 2005 growing season. The largest irrigation water use efficiency (IWUE) was observed in the T₂₅ (1.46 kg m⁻³), and the smallest IWUE was in the T₁₀₀ treatment (0.81 kg m⁻³) in the experimental years. A yield response factor (k_y) value of 0.78 was determined based on averages of two years. Leaf area index (LAI) and dry matter yields (DM) increased with increasing water use for treatments. Fiber qualities were influenced by drip irrigation levels in both years. The results revealed that well-irrigated treatments (T₁₀₀) could be used for the semi-arid climatic conditions under no water shortage. Moreover, the results also demonstrated that irrigation of cotton with drip irrigation method at 75% level (T₇₅) had significant benefits in terms of saved irrigation water and large WUE indicating a definitive advantage of deficit irrigation under limited water supply conditions. In an economic viewpoint, 25.0% saving in irrigation water (T₇₅) resulted in 34.0% reduction in the net income. However, the net income of the T₁₀₀ treatment is found to be reasonable in areas with no water shortage.     

Nutrient management adaptation for dryland maize yields and water use efficiency to long-term rainfall variability in China

Rainfed crop production in northern China is constrained by low and variable rainfall, and by improper management practices. This study explored both the impact of long-term rainfall variability and the long-term effects of various combinations of maize stover, cattle manure and mineral fertiliser (NP) applications on maize (Zea mays L.) yields and water use efficiency (WUE) under reduced tillage practices, at Shouyang Dryland Farming Experimental Station in northern China from 1993 onwards. The experiment was set up according to an incomplete, optimal design, with 3 factors at five levels and 12 treatments including a control with two replications. Grain yields were greatly influenced by the amount of rain during the growing season, and by soil water at sowing. Annual mean grain yields ranged from 3 to 10 t ha⁻¹ and treatment mean yields from 4.2 to 7.2 t ha⁻¹. The WUE ranged from 40 in treatments with balanced nutrient inputs in dry (weather/or soil) years to 6.5 kg ha⁻¹ mm⁻¹ for the control treatments in wet years. The WUE averaged over the 15-year period ranged from 11 to 19 kg ha⁻¹ mm⁻¹. Balanced combination of stover (3000-6000 kg), manure (1500-6000 kg) and N fertiliser (105 kg) gave the highest yield and hence WUE. It is suggested that 100 kg N per ha should be a best choice, to be adapted according to availability of stover and manure. Possible management options under variable rainfall conditions to alleviate occurring moisture stress for crops must be tailored to the rainfall pattern. The potentials of split applications, targeted to the need of the growing crop (response nutrient management), should be explored to further improve grain yield and WUE.     

Irrigation strategies to improve the water use efficiency of wheat-maize double cropping systems in North China Plain

Water is the most important limiting factor of wheat (Triticum aestivum L.) and maize (Zea mays L.) double cropping systems in the North China Plain (NCP). A two-year experiment with four irrigation levels based on crop growth stages was used to calibrate and validate RZWQM2, a hybrid model that combines the Root Zone Water Quality Model (RZWQM) and DSSAT4.0. The calibrated model was then used to investigate various irrigation strategies for high yield and water use efficiency (WUE) using weather data from 1961 to 1999. The model simulated soil moisture, crop yield, above-ground biomass and WUE in responses to irrigation schedules well, with root mean square errors (RMSEs) of 0.029 cm³ cm⁻³, 0.59 Mg ha⁻¹, 2.05 Mg ha⁻¹, and 0.19 kg m⁻³, respectively, for wheat; and 0.027 cm³ cm⁻³, 0.71 Mg ha⁻¹, 1.51 Mg ha⁻¹ and 0.35 kg m⁻³, respectively, for maize. WUE increased with the amount of irrigation applied during the dry growing season of 2001-2002, but was less sensitive to irrigation during the wet season of 2002-2003. Long-term simulation using weather data from 1961 to 1999 showed that initial soil water at planting was adequate (at 82% of crop available water) for wheat establishment due to the high rainfall during the previous maize season. Preseason irrigation for wheat commonly practiced by local farmers should be postponed to the most sensitive growth stage (stem extension) for higher yield and WUE in the area. Preseason irrigation for maize is needed in 40% of the years. With limited irrigation available (100, 150, 200, or 250 mm per year), 80% of the water allocated to the critical wheat growth stages and 20% applied at maize planting achieved the highest WUE and the least water drainage overall for the two crops.     

Yield and water-production functions of two durum wheat cultivars grown under different irrigation and nitrogen regimes

Wheat (Triticum durum L.) yields in the semi-arid regions are limited by inadequate water supply late in the cropping season. Planning suitable irrigation strategy and nitrogen fertilization with the appropriate crop phenology will produce optimum grain yields. A 3-year experiment was conducted on deep, fairly drained clay soil, at Tal Amara Research Station in the central Bekaa Valley of Lebanon to investigate the response of durum wheat to supplemental irrigation (IRR) and nitrogen rate (NR). Three water supply levels (rainfed and two treatments irrigated at half and full soil water deficit) were coupled with three N fertilization rates (100, 150 and 200 kg N ha⁻¹) and two cultivars (Waha and Haurani) under the same cropping practices (sowing date, seeding rate, row space and seeding depth). Averaged across N treatments and years, rainfed treatment yielded 3.49 Mg ha⁻¹ and it was 25% and 28% less than half and full irrigation treatments, respectively, for Waha, while for Haurani the rainfed treatment yielded 3.21 Mg ha⁻¹, and it was 18% and 22% less than half and full irrigation, respectively. On the other hand, N fertilization of 150 and 200 kg N ha⁻¹ increased grain yield in Waha by 12% and 16%, respectively, in comparison with N fertilization of 100 kg N ha⁻¹, while for cultivar Haurani the increases were 24% and 38%, respectively. Regardless of cultivar, results showed that supplemental irrigation significantly increased grain number per square meter and grain weight with respect to the rainfed treatment, while nitrogen fertilization was observed to have significant effects only on grain number per square meter. Moreover, results showed that grain yield for cultivar Haurani was less affected by supplemental irrigation and more affected by nitrogen fertilization than cultivar Waha in all years. However, cultivar effects were of lower magnitude compared with those of irrigation and nitrogen. We conclude that optimum yield was produced for both cultivars at 50% of soil water deficit as supplemental irrigation and N rate of 150 kg N ha⁻¹. However, Harvest index (HI) and water use efficiency (WUE) in both cultivars were not significantly affected neither by supplemental irrigation nor by nitrogen rate. Evapotranspiration (ET) of rainfed wheat ranged from 300 to 400 mm, while irrigated wheat had seasonal ET ranging from 450 to 650 mm. On the other hand, irrigation treatments significantly affected ET after normalizing for vapor pressure deficit (ET/VPD) during the growing season. Supplemental irrigation at 50% and 100% of soil water deficit had approximately 26 and 52 mm mbar⁻¹ more ET/VPD, respectively, than those grown under rainfed conditions.     

Forage quality, water use and nitrogen utilization efficiencies of pearl millet (Pennisetum americanum L.) grown under different soil moisture and nitrogen levels

The increasing scarcity of water for irrigation is becoming the most important problem for producing forage in all arid and semi-arid regions. Pearl millet is a key crop in these regions which needs relatively less water than other crops. In this research, a field study was conducted to identify the best combination of irrigation and nitrogen (N) management to achieve acceptable pearl millet forage both in quantity and quality aspects. Pearl millet was subjected to four irrigation treatments with interaction of N fertilizer (0, 75, 150 and 225 kg ha⁻¹). The irrigation treatments were 40%, 60%, 80% and 100% of total available soil water (I₄₀, I₆₀, I₈₀ and I₁₀₀, respectively). The results showed that increasing moisture stress (from I₄₀ to I₁₀₀) resulted in progressively less total dry matter (TDM), leaf area index (LAI), and nitrogen utilization efficiency (NUzE), while water use efficiency (WUE) and the percentage of crude protein (CP%) increased. The highest TDM and LAI were found to be 21.45 t ha⁻¹ and 8.65, in I₄₀ treatment, respectively. TDM, WUE, CP% and profit responses to N rates were positive. The maximum WUE of 4.19 kg DM/m³ was achieved at I₁₀₀ with 150 kg N ha⁻¹. The results of this research indicate that the maximum profit of forage production was obtained in plots which were fully irrigated (I₄₀) and received 225 kg N ha⁻¹. However, in the situation which water is often limited and not available, application of 150 kg N ha⁻¹ can produce high forage quality and guaranty acceptable benefits for farmers.     

Yield and quality response of drip irrigated broccoli (Brassica oleracea L. var. italica) under different irrigation regimes, nitrogen applications and cultivation periods

The experiment aimed at evaluating the yield and quality response of broccoli (Brassica oleracea L. var. italica) to applied irrigation water and nitrogen by drip irrigation method during the spring and autumn cultivation periods of 2007. Irrigation water was applied based on a ratio of Class A pan evaporation (k_cp = 0.50, 0.75, 1.00 and 1.25) with 7 days interval. Also, the effect of four nitrogen levels (0 kg ha⁻¹, 150 kg ha⁻¹, 200 kg ha⁻¹ and 250 kg ha⁻¹) was compared with each treatment. The seasonal evapotranspiration in the treatments varied from 233 mm to 328 mm during the spring period and from 276 mm to 344 mm during the autumn period. The highest broccoli yield was obtained in the spring period as 11.02 t ha⁻¹ and in the autumn period as 4.55 t ha⁻¹. In general, there were statistical differences along nitrogen does with respect to yield and yield components while there were no statistically significant differences in the yield and yield components among irrigation regimes. Both yield and yield parameters in the spring period were found to be higher than that of the autumn period due to the low temperature and high rainy days in autumn. Irrigation water use efficiency (IWUE) ranged from 3.78 kg m⁻³ to 14.61 kg m⁻³ during the spring period and from 1.89 kg m⁻³ to 5.93 kg m⁻³ during the autumn period. On the other hand, nitrogen use efficiency (NUE) changed as 37.32-73.13% and 13.08-22.46% for spring and autumn season, respectively.     

Evaluation of the influence of irrigation methods and water quality on sugar beet yield and water use efficiency

Rapid urbanization and industrialization have increased the pressure on limited existing fresh water to meet the growing needs for food production. Two immediate responses to this challenge are the efficient use of irrigation technology and the use of alternative sources of water. Drip irrigation methods may play an important role in efficient use of water but there is still limited information on their use on sugar beet crops in arid countries such as Iran. An experiment was conducted to evaluate the effects of irrigation method and water quality on sugar beet yield, percentage of sugar content and irrigation water use efficiency (IWUE). The irrigation methods investigated were subsurface drip, surface drip and furrow irrigation. The two waters used were treated municipal effluent (EC = 1.52 dS m⁻¹) and fresh water (EC = 0.509 dS m⁻¹). The experiments used a split plot design and were undertaken over two consecutive growing seasons in Southern Iran. Statistical testing indicated that the irrigation method and water quality had a significant effect (at the 1% level) on sugar beet root yield, sugar yield, and IWUE. The highest root yield (79.7 Mg ha⁻¹) was obtained using surface drip irrigation and effluent and the lowest root yield (41.4 Mg ha⁻¹) was obtained using furrow irrigation and fresh water. The highest IWUE in root yield production (9 kg m⁻³) was obtained using surface drip irrigation with effluent and the lowest value (3.8 kg m⁻³) was obtained using furrow irrigation with fresh water. The highest IWUE of 1.26 kg m⁻³ for sugar was obtained using surface drip irrigation. The corresponding efficiency using effluent was 1.14 kg m⁻³. Irrigation with effluent led to an increase in the net sugar yield due to an increase in the sugar beet root yield. However, there was a slight reduction in the percentage sugar content in the plants. This study also showed that soil water and root depth monitoring can be used in irrigation scheduling to avoid water stress. Such monitoring techniques can also save considerable volumes of irrigation water and can increase yield.     

The effects of irrigation methods with effluent and irrigation scheduling on water use efficiency and corn yields in an arid region

A great challenge for the agricultural sector is to produce more food from less water, particularly in arid and semi-arid regions which suffer from water scarcity. A study was conducted to evaluate the effect of three irrigation methods, using effluent versus fresh water, on water savings, yields and irrigation water use efficiency (IWUE). The irrigation scheduling was based on soil moisture and rooting depth monitoring. The experimental design was a split plot with three main treatments, namely subsurface drip (SSD), surface drip (SD) and furrow irrigation (FI) and two sub-treatments effluent and fresh water, which were applied with three replications. The experiment was conducted at the Marvdasht city (Southern Iran) wastewater treatment plant during 2005 and 2006. The experimental results indicated that the average water applied in the irrigation treatments with monitoring was much less than that using the conventional irrigation method (using furrows but based on a constant irrigation interval, without moisture monitoring). The maximum water saving was obtained using SSD with 5907 m³ ha⁻¹ water applied, and the minimum water saving was obtained using FI with 6822 m³ ha⁻¹. The predicted irrigation water requirements using the Penman-Monteith equation (considering 85% irrigation efficiency for the FI method) was 10,743 m³ ha⁻¹. The pressure irrigation systems (SSD and SD) led to a greater yield compared to the surface method (FI). The highest yield (12.11 × 10³ kg ha⁻¹) was obtained with SSD and the lowest was obtained with the FI method (9.75 × 10³ kg ha⁻¹). The irrigation methods indicated a highly significant difference in irrigation water use efficiency. The maximum IWUE was obtained with the SSD (2.12 kg m⁻³) and the minimum was obtained with the FI method (1.43 kg m⁻³). Irrigation with effluent led to a greater IWUE compared to fresh water, but the difference was not statistically significant.     

Agronomic and economic response to furrow diking tillage in irrigated and non-irrigated cotton (Gossypium hirsutum L.)

The Southeast U.S. receives an average of 1300 mm annual rainfall, however poor seasonal distribution of rainfall often limits production. Irrigation is used during the growing season to supplement rainfall to sustain profitable crop production. Increased water capture would improve water use efficiency and reduce irrigation requirements. Furrow diking has been proposed as a cost effective management practice that is designed to create a series of storage basins in the furrow between crop rows to catch and retain rainfall and irrigation water. Furrow diking has received much attention in arid and semi-arid regions with mixed results, yet has not been adapted for cotton production in the Southeast U.S. Our objectives were to evaluate the agronomic response and economic feasibility of producing cotton with and without furrow diking in conventional tillage over a range of irrigation rates including no irrigation. Studies were conducted at two research sites each year from 2005 to 2007. Irrigation scheduling was based on Irrigator Pro for Cotton software. The use of furrow diking in these studies periodically reduced water consumption and improved yield and net returns. In 2006 and 2007, when irrigation scheduling was based on soil water status, an average of 76 mm ha⁻¹ of irrigation water was saved by furrow diking, producing similar cotton yield and net returns. Furrow diking improved cotton yield an average of 171 kg ha⁻¹ and net return by $245 ha⁻¹ over multiple irrigation rates, in 1 of 3 years. We conclude that furrow diking has the capability to reduce irrigation requirements and the costs associated with irrigation when rainfall is periodic and drought is not severe.     

Effects of deficit irrigation on the yield and yield components of drip irrigated cotton in a mediterranean environment

A field study on cotton (Gossypium hirsutum L., cv.) was carried out from 2005 to 2008 in the Çukurova Region, Eastern Mediterranean, Turkey. Treatments were designated as I₁₀₀ full irrigation; DI₇₀, DI₅₀ and DI₀₀ which received 70, 50, and 0% of the irrigation water amount applied in the I₁₀₀ treatment. The irrigation water amount to be applied to the plots was calculated using cumulative pan evaporation that occurred during the irrigation intervals. The effect of water deficit or water stress on crop yield and some plant growth parameters such as yield response, water use efficiencies, dry matter yield (DM), leaf area index (LAI) as well as on lint quality components was evaluated. The average seasonal evapotranspiration ranged from 287 ± 15 (DI₀₀) to 584 ± 80 mm (I₁₀₀). Deficit irrigation significantly affected crop yield and all yield components considered in this study. The average seed cotton yield varied from 1369 ± 197 (DI₀₀) to 3397 ± 508 kg ha⁻¹ (I₁₀₀). The average water use efficiency (WUE_ET) ranged from 6.0 ± 1.6 (I₁₀₀) to 4.8 ± 0.9 kg ha⁻¹ mm⁻¹ (DI₀₀), while average irrigation water use efficiency (WUE_I) was between 9.4 ± 3.0 (I₁₀₀) and 14.4 ± 4.8 kg ha⁻¹ mm⁻¹ (DI₅₀). Deficit irrigation increased the harvest index (HI) values from 0.26 ± 0.054 (I₁₀₀) to 0.32 ± 0.052 kg kg⁻¹ (DI₅₀). Yield response factor (Ky) was determined to be 0.98 based on four-year average. Leaf area index (LAI) and dry matter yields (DM) increased with increasing water use. This study demonstrated that the full irrigated treatment (I₁₀₀) should be used for semiarid conditions with no water shortage. However, DI₇₀ treatment needs to be considered as a viable alternative for the development of reduced irrigation strategies in semiarid regions where irrigation water supplies are limited.     

Using EPIC model to manage irrigated cotton and maize

Simulation models are becoming of interest as a decision support system for management and assessment of crop water use and of crop production. The Environmental Policy Integrated Climate (EPIC) model was used to evaluate its application as a decision support tool for irrigation management of cotton and maize under South Texas conditions. Simulation of the model was performed to determine crop yield, crop water use, and the relationships between the yield and crop water use parameters such as crop evapotranspiration (ETc) and water use efficiency (WUE). We measured actual ETc using a weighing lysimeter and crop yields by field sampling, and then calibrated the model. The measured variables were compared with simulated variables using EPIC. Simulated ETc agreed with the lysimeter, in general, but some simulated ETc were biased compared with measured ETc. EPIC also simulated the variability in crop yields at different irrigation regimes. Furthermore, EPIC was used to simulate yield responses at various irrigation regimes with farm fields’ data. Maize required ∼700 mm of water input and ∼650 mm of ETc to achieve a maximum yield of 8.5 Mg ha⁻¹ while cotton required between 700 and 900 mm of water input and between 650 and 750 mm of ETc to achieve a maximum yield of 2.0-2.5 Mg ha⁻¹. The simulation results demonstrate that the EPIC model can be used as a decision support tool for the crops under full and deficit irrigation conditions in South Texas. EPIC appears to be effective in making long-term and pre-season decisions for irrigation management of crops, while reference ET and phenologically based crop coefficients can be used for in-season irrigation management.     

Yield, water and nitrogen-use response of rice to zeolite and nitrogen fertilization in a semi-arid environment

Water scarcity and soil nitrogen (N) loss are important limitations for agricultural production in semi-arid region especially for rice production. Zeolite (Z) as a soil conditioner can be used to retrain water and nitrogen in near-surface soil layer in lowland rice production system. The objectives of this study were to investigate the effects of different application rates of natural zeolite (clinoptilolite) and nitrogen on rice yield, yield components, soil nitrogen, water use, water productivity in a silty clay soil in 2004 and 2005. Zeolite was only applied in the first year. In order to study the long-term and continuous effect of zeolite on the objectives of the study, no zeolite was applied in the second year and the study was conducted on the same land as the first year. Zeolite and N were applied at rates of 0, 2, 4, and 8 t ha⁻¹ and 0, 20, 40, and 80 kg ha⁻¹, respectively in 2004. In 2005, each plot received the same amount of N as received in 2004. It is concluded that by decreasing N application rates, higher Z application rate is needed to improve grain yield. Highest grain yield was obtained at N application rate of 80 kg ha⁻¹ and Z application rate of 4 t ha⁻¹. Higher grain yield was mostly attributed to lower unfilled grain percentage and higher 1000-grain weight that were a result of higher N application rate and N retention in soil due to Z application. Nitrogen and Z applications resulted in higher grain protein contents and nitrogen recovery efficiency (NRE). Based on these results and due to higher N retention in soil under Z application, improved grain yield quality, nitrogen-use efficiency (NUE), and nitrogen recovery efficiency (NRE) could be obtained at Z application rate of 8 t ha⁻¹ and N application rate of 80 kg ha⁻¹ or more. However, this was not satisfied for NUE. Moreover, it is found that at higher N application rates lower Z application rates are needed to effectively retain soil residual mineral nitrogen. Furthermore, at N application rates of 80 kg ha⁻¹ or more, Z application increased soil water retention and resulted in lower seasonal water use and higher water productivity. In general, it was concluded that the effect of Z application in retaining soil N was also effective in the second year.     

Effects of N fertilization on root development and activity of water-stressed cotton (Gossypium hirsutum L.) plants

The objective of this investigation was to study effects of nitrogen on drought resistance in terms of changes in cotton (Gossypium hirsutum L.) root dry matter accumulation, N concentration, antioxidant enzyme activities and root vigor during short-duration water stress (withholding water for 8 days and then permitting to 10 days recover by re-watering). Cotton plants were grown in pots with three N levels (0, 240, and 480 kg N ha⁻¹). Soil-relative water content decreased with increasing N supply during the soil water stress period, while leaf area, dry matter production and N accumulation were enhanced. The root/shoot ratio and root-N/shoot-N ratio increased with water stress, and were smallest at 240 kg N ha⁻¹. Application of N increased the activities of peroxidase (POD) and catalase (CAT) of cotton root, but decreased superoxide dismutase (SOD) activity during water stress as well as during recovery. Malondialdehyde (MDA) content was significantly (p < 0.05) increased, and was lowest in the 240 kg N ha⁻¹ N treatment during water stress. At the 10th day after soil re-watering, MDA content of 240 kg N ha⁻¹ was similar to that of 480 kg N ha⁻¹, but less than that of 0 kg N ha⁻¹. The root vigor, which was debased by water stress, was the highest at 240 kg N ha⁻¹. After soil re-watering, N application promoted root vigor. The trends of net photosynthetic rate were the same as that of root vigor during water stress. These results suggest that appropriate N supply (240 kg N ha⁻¹ in this investigation) may contribute to drought resistance of cotton plants by adjusting the antioxidant enzyme activities of root, debasing lipid peroxidation and boosting root vigor during short-duration water stress (withholding water for 8 days in this investigation), however, excessive N supply (480 kg N ha⁻¹) had a deleterious effect on plant drought resistance.     

Chickpea water use efficiency in relation to cropping system, cultivar, soil nitrogen and Rhizobial inoculation in semiarid environments

Crops grown in semiarid rainfed conditions are prone to water stress which could be alleviated by improving cultural practices. This study determined the effect of cropping system, cultivar, soil nitrogen status and Rhizobium inoculation (Rz) on water use and water use efficiency (WUE) of chickpea (Cicer arietinum L.) in semiarid environments. The cultivars Amit, CDC Anna, CDC Frontier, and CDC Xena were grown in no-till barley, no-till wheat, and tilled-fallow systems and under various rates of N fertilizer (0, 28, 56, 84, and 112 kg N ha⁻¹) coupled with or without Rz. The study was conducted at Swift Current and Shaunavon, Saskatchewan, from 2004 to 2006. On average, chickpea used about 10 mm of water from the top 0-15 cm soil depth. In the tilled-fallow system, chickpea extracted 20% more water in the 15-30 cm depth, 70% more in the 30-60 cm depth, and 156% more in the 60-120 cm depth than when it was grown in the no-till systems. CDC Xena had WUE of 5.3 kg ha⁻¹ mm⁻¹ or 20% less than the average WUE (6.6 kg ha⁻¹ mm⁻¹) of the three other cultivars, even though these cultivars used the same amounts of water. Water use efficiency increased from 4.7 to 6.8 kg ha⁻¹ mm⁻¹ as N fertilizer rate was increased from 0 to 112 kg N ha⁻¹ when chickpea was grown in the no-till barley or wheat systems, but chickpea grown in the tilled-fallow system did not respond to changes in the fertilizer N rates averaging WUE of 6.5 kg ha⁻¹ mm⁻¹. In the absence of N fertilizer, the application of Rz increased WUE by 33% for chickpea grown in the no-till barley system, 30% in the no-till wheat system, and 9% in the tilled-fallow system. Chickpea inoculated with Rhizobium achieved a WUE value similar to the crop fertilized at 84 kg N ha⁻¹. Without the use of Rz, chickpea increased WUE in a linear fashion with increasing fertilizer N rates from 0 to 84 kg N ha⁻¹. Cropping system, cultivar, and inoculation all had greater impact on WUE than on the amount of water extracted by the crop from the soil. The improvement of cultural practices to promote general plant health along with the development of cultivars with improved crop yields will be keys for improving water use efficiency of chickpea in semiarid environments.     

Yield and quality of melon grown under different irrigation and nitrogen rates

During 2 years, a melon crop (Cucumis melo L. cv. Sancho) was grown under field conditions to investigate the effects of different nitrogen (N) and irrigation (I) levels on fruit yield, fruit quality, irrigation water use efficiency (IWUE) and nitrogen applied efficiency (NAE). The statistical design was a split-plot with four replications, where irrigation was the main factor of variation and N was the secondary factor. In 2005, irrigation treatments consisted of applying daily a moderate water stress equivalent to 75% of ETc (crop evapotranspiration), a 100% ETc control and an excess irrigation of 125% ETc (designated as I₇₅, I₁₀₀ and I₁₂₅), while the N treatments were 30, 85, 112 and 139 kg N ha⁻¹ (designated as N₃₀, N₈₅, N₁₁₂ and N₁₃₉). In 2006, both the irrigation and N treatments applied were: 60, 100 and 140% ETc (I₆₀, I₁₀₀ and I₁₄₀) and 93, 243 and 393 kg N ha⁻¹ (N₉₃, N₂₄₃ and N₃₉₃). Moderate water stress did not reduce melon yield and high IWUE was obtained. Under severe deficit irrigation, the yield was reduced by 22% mainly due to decrease fruit weight. The relative yield (yield/maximum yield) was higher than 95% when the irrigation depth applied was in the range of 87-136% ETc. In 2006, the interaction between irrigation and N was significant for yield, fruit weight and IWUE. The best yield, 41.3 Mg ha⁻¹, was obtained with 100% ETc at N₉₃. The flesh firmness and the placenta and seeds weight increased when the irrigation level was reduced by 60% ETc. The highest NAE was obtained with quantities of water close to 100% ETc and increased as the N level was reduced. The highest IWUE was obtained with applications close to 90 kg N ha⁻¹. The I₂₄₃ and I₃₉₃ treatments produced inferior fruits due to higher skin ratios and lower flesh ratios. These results suggest that it is possible to apply moderate deficit irrigation, around 90% ETc, and reduce nitrogen input to 90 kg ha⁻¹ without lessening quality and yields.     

Tomato nitrogen accumulation and fertilizer use efficiency on a sandy soil, as affected by nitrogen rate and irrigation scheduling

Tomato production systems in Florida are typically intensively managed with high inputs of fertilizer and irrigation and on sandy soils with low inherent water and nutrient retention capacities; potential nutrient leaching losses undermine the sustainability of such systems. The objectives of this 3-year field study were to evaluate the interaction between N-fertilizer rates and irrigation scheduling on crop N and P accumulation, N-fertilizer use efficiency (NUE) and NO₃-N leaching of tomato cultivated in a plastic mulched/drip irrigated production system in sandy soils. Experimental treatments were a factorial combination of three irrigation scheduling regimes and three N-rates (176, 220, and 330 kg ha⁻¹). Irrigation treatments included were: (1) surface drip irrigation (SUR) both the irrigation and fertigation line placed underneath the plastic mulch; (2) subsurface drip irrigation (SDI) where the irrigation drip was placed 0.15 m below the fertigation line which was located on top of the bed; and (3) TIME (conventional control) with the irrigation and fertigation lines placed as in SUR and irrigation applied once a day. Except for the TIME treatment all irrigation treatments were soil moisture sensor (SMS)-based with irrigation occurring at 10% volumetric water content. Five irrigation windows were scheduled daily and events were bypassed if the soil water content exceeded the established threshold. The use of SMS-based irrigation systems significantly reduced irrigation water use, volume percolated, and nitrate leaching. Based on soil electrical conductivity (EC) readings, there was no interaction between irrigation and N-rate treatments on the movement of fertilizer solutes. Total plant N accumulation for SUR and SDI was 12-37% higher than TIME. Plant P accumulation was not affected by either irrigation or N-rate treatments. The nitrogen use efficiency for SUR and SDI was on the order of 37-45%, 56-61%, and 61-68% for 2005, 2006 and 2007, respectively and significantly higher than for the conventional control system (TIME). Moreover, at the intermediate N-rate SUR and SDI systems reduced NO₃-N leaching to 5 and 35 kg ha⁻¹, while at the highest N-rate corresponding values were 7 and 56 kg N ha⁻¹. Use of N application rates above 220 kg ha⁻¹ did not result in fruit and/or shoot biomass nor N accumulation benefits, but substantially increased NO₃-N leaching for the control treatment, as detected by EC monitoring and by the lysimeters. It is concluded that appropriate use of SDI and/or sensor-based irrigation systems can sustain high yields while reducing irrigation application as well as reducing NO₃-N leaching in low water holding capacity soils.     

Evaluation of humic substances fertigation through surface and subsurface drip irrigation systems on potato grown under Egyptian sandy soil conditions

The aim of this study was to evaluate the effect of humic substances application in sandy soil under surface and subsurface drip irrigation systems on potato tubers yield quantity, quality, nutrients concentration in tubers and soil fertility after harvesting. For this purpose, field experiment was carried out at the experimental farm of the Agricultural Research Station, National Research Center, El-Nubaria district, Egypt during the winter season of 2007/2008. The used experimental design was split plot design with three replicates, main treatments were presented irrigation systems, i.e. surface and subsurface drip irrigation, while subtreatments were presented rates of humic substances additives which were 0, 60 and 120 kg ha⁻¹. Results showed that increasing humic substances application rates up to 120 kg ha⁻¹ enhanced tubers yield quantity, starch content and total soluble solids. The increase of humic substances application rates was associated with the decrease of nutrients leaching, which was reflected on increasing macro- and micronutrients concentration in potato tubers, as well as increasing concentration of these nutrients in soil after tubers harvesting. Subsurface drip irrigation system was found to be more efficient than surface drip irrigation system on improving tubers yield quantity, quality parameters and nutrients concentration content, in addition to soil fertility after harvesting.