Changes in some physical properties of a clay soil in Central Italy following the passage of rubber tracked and wheeled tractors of medium power

The aim of this study was to evaluate the compacting effect of rubber tracked tractors in comparison to that of the traditional wheeled tractors. Macroporosity, pore shape and size distribution, bulk density, penetration resistance and saturated hydraulic conductivity were analysed in a clay soil (Vertic Cambisol) near Rome (Italy) following one and four passes on the same track of rubber tracked and wheeled tractors of medium power. The soil structure attributes were evaluated by characterising porosity by means of image analysis of soil thin sections prepared from undisturbed samples. Macroporosity decreased in the 0–10 cm layer of compacted soil, particularly after four tractor passes, due to a large reduction in the proportion of elongated pores and in their vertical continuity. The rubber tracked tractor had a more pronounced compaction effect in the surface layer (0–10 cm) than the wheeled tractor both after one and four passes; the latter treatment producing the lowest soil porosity. The same trend was observed for hydraulic conductivity, which showed a highly significant correlation with elongated pores. In the 10–20 cm layer the porosity was significantly decreased following traffic, apart from in the soil under one pass of the rubber tracked tractor. Again in this layer, the lowest values of porosity were found in soil after four passes of the rubber tracked tractor. Single and multiple passes made by the two tractors induced different effects regarding soil penetration resistance and bulk density. Increment ratio of penetration resistance after tractor passes with respect to the control was: 12.5 and 49.9% with the wheeled and 34.4 and 39.8% with the tracked after one and four passes, respectively. Increment ratio of dry bulk density values after tractor passes with respect to the control was 7.9 and 11.7% with the wheeled and 7.5 and 8.3% with the tracked after one and four passes, respectively. The tractor passes transformed the initial subangular blocky structure into a massive structure with sometimes a platy structure in the upper few centimetres. The results indicated that soil compaction following traffic with the rubber tracked tractor was generally the more pronounced. However the compacting effect of this tractor after one pass seemed to be limited to the surface layer only.     

Influence of single passes with high wheel load on a structured, unploughed sandy loam soil

In a field experiment, a sandy loam was subjected to single passes with a sugar beet harvester at two different soil water potentials. Different hopper fillings resulted in ground contact pressures of 130 kPa (partial load) and 160 kPa (full load) underneath the tyre. Bulk density, macroporosity (equivalent pore radius >100 μm), penetrometer resistance, air permeability and pre-consolidation pressure were measured within and next to the wheel tracks at depths of 0.12–0.17, 0.32–0.37 and 0.52–0.57 m. Furthermore, the soil structure at two horizons (Ahp 7–24 cm, B(C) 24–38 cm) was visually assessed and classified.

The moist plot responded to a wheel load of 11.23 mg (160 kPa) with an increase in bulk density and pre-consolidation pressure as well as with a decrease in air permeability and macroporosity at a depth of 0.12–0.17 m. With a wheel load of 7.47 mg (130 kPa) on the moist plot and with both wheel load levels on the dry plot, only slight changes of the soil structure were detected. At a depth of 0.32–0.37 and 0.52–0.57 m, the measurements did not indicate any compaction. An ANOVA indicates that the factor “soil water potential” and the factor “wheel load” significantly influence the bulk density at a depth of 0.12–0.17 m. No interactions occurred between these two factors. The wheel traffic on the test plot had no effect on the yield of winter wheat planted after the experimental treatment.

Bulk density, macroporosity and pre-consolidation pressure proved to be sensitive to detect compaction because they varied only slightly and are easy to measure. In contrast, the standard deviation of air permeability is large. The soil structure determined visually in the field confirms the values measured in the laboratory. The results of the penetrometer resistance measurements were not explainable.     

The consequences of wheel-induced soil compaction and subsoiling for silage maize on a sandy loam soil in Belgium

In Belgium, growing silage maize in a monoculture often results in increased soil compaction. The aim of our research was to quantify the effects of this soil compaction on the dry matter (DM) yields and the nitrogen use of silage maize (Zea mays L.). On a sandy loam soil of the experimental site of Ghent University (Belgium), silage maize was grown on plots with traditional soil tillage (T), on artificially compacted plots (C) and on subsoiled plots (S). The artificial compaction, induced by multiple wheel-to-wheel passages with a tractor, increased the soil penetration resistance up to more than 1.5 MPa in the zone of 0–35 cm of soil depth. Subsoiling broke an existing plough pan (at 35–45 cm of soil depth). During the growing season, the release of soil mineral nitrogen by mineralisation was substantially lower on the C plots than on the T and S plots. Silage maize plants on the compacted soil were smaller and flowering was delayed. The induced soil compaction caused a DM yield loss of 2.37 Mg ha⁻¹ (−13.2%) and decreased N uptake by 46.2 kg ha⁻¹ (−23.2%) compared to the T plots. Maize plants on compacted soil had a lower, suboptimal nitrogen content. Compared with the traditional soil tillage that avoided heavy compaction, subsoiling offered no significant benefits for the silage maize crop. It was concluded that avoiding heavy soil compaction in silage maize is a major strategy for maintaining crop yields and for enhancing N use efficiency.     

Effects of intensifying organic manuring and tillage practices on penetration resistance and infiltration rate

Soil erosion, along with the contributing factors of soil crusting and sealing, have received minimal scientific attention to date in Latin America. This study was conducted in an Andean hillside environment to determine how the local organic manuring and tillage practices influence the development of soil crusting and sealing, and the extent to which these practices influence soil water infiltration. The aim of this study was to identify treatments that prevented superficial soil structural constraints, i.e. treatments which maintain infiltration and therefore reduce potential soil erosion and run-off.

Treatment results were measured with a pocket penetrometer and a mini-rain simulator on nine different cropping systems, mainly based on cassava (Manihot esculenta Crantz), from February to November 2000 and 2001. The cropping systems were laid out on a Ferrallic Cambisol, an acid, vulcanically influenced soil of the Andean region.

In both cropping cycles, treatments with chicken manure application developed superficial soil crusts during the dry season. For a treatment manured with 8 t ha⁻¹ chicken manure, this crust meant an increase in penetration resistance from 2.3 kg cm⁻² in April 2000 to 16.2 kg cm⁻² in July 2000. The change in superficial soil structure created a notable reduction in final infiltration from 92 to 42.2 mm h⁻¹. A minimum tillage treatment which displayed the highest penetration resistance during the dry periods of up to 46.4 kg cm⁻² presented no restricting effects on soil water intake (76.2 mm h⁻¹ final infiltration in 2000) due to an optimal aggregate development during 10 years of consecutive conservation practice.

Measurements of penetration resistance and infiltration showed that soil conserving treatments, such as minimum tillage and crop rotations, improved the physical soil status and prevented soil crusting developing along with its negative effects on infiltration. These methods can therefore be strongly recommended to farmers.     

Physical characterization of a soil amended with organic residues in a rice–wheat cropping system using a single value soil physical index

The effect of soil incorporations of lantana (Lantana spp.) biomass, an obnoxious weed, on physical environment of a silty clay loam soil (Typic Hapludalf) under rice (Oryza sativa L.)–wheat (Triticum aestivum L.) cropping was studied in a long-term field experiment conducted in a wet temperate region of north India. Fresh lantana biomass was incorporated into the plough layer at 10, 20 and 30 Mg ha⁻¹ annually, 7–10 days before puddling. Plant-available water capacity (PAWC), non-limiting water range (NLWR) and NLWR:PAWC ratio were determined to characterize soil physical environment during wheat crop in the tenth cropping cycle.

Ten annual applications of lantana at 10, 20 and 30 Mg ha⁻¹, increased organic carbon (OC) content over control by 12.6, 17.6 and 27.9% in 0–15 cm soil layer, and 17.1, 26.3 and 39.5% in 15–30 cm soil layer, respectively. The OC content in 0–15 and 15–30 cm soil layer of control plots was 11.1 and 7.6 g kg⁻¹ soil. Bulk density decreased by 3–14% in 7.5–10.5 cm layer and 1–6% in 15–18 cm layer. Volumetric moisture contents at 10% air-filled porosity were 38.4, 40.0, 54.5 and 55.7% at 7.5–10.5 cm depth, and 31.4, 32.2, 33.9 and 34.6% at 15–18 cm depth corresponding to 0, 10, 20 and 30 Mg ha⁻¹ lantana treatment, respectively. At 15–18 cm soil depth, volumetric moisture contents at 2 MPa soil penetration resistance were 26.9, 24.8, 23.0 and 19.6% in zero, 10, 20 and 30 Mg ha⁻¹ lantana-treated plots, respectively. Lower soil water contents associated with 10% air-filled porosity and greater soil water contents associated with a limiting penetration resistance of 2 MPa resulted in a lower NLWR (4.3%) for control as compared to lantana-treated soil (7.4–15.1%). The PAWC showed slight increase from 12.9 to 13.4–14.9% due to lantana additions. The NLWR:PAWC ratio was also lower in control (0.33) as compared to lantana-treated soil (0.55–1.01). The NLWR was significantly and positively correlated with wheat grain yield (r=0.858^**).     

Soil physical responses to novel rice cultural practices in the rice–wheat system: Comparative evidence from a swelling soil in Nepal

Soil puddling in advance of rice (Oryza sativa L.) transplanting disperses surface aggregates and generates compaction at depth. As a management scheme for rice, puddling is typically considered advantageous for maximizing resource availability and yield. However, some experimental findings suggest a conflict between edaphic conditions created by this establishment technique and the performance of subsequent non-rice crops like wheat (Triticum aestivum L.). At a site in the mid-hills region of Nepal on a silt loam soil with vertic characteristics, we compared the impact of six rice tillage (surface tillage—T₁, shank subsoiler—T₂, shank subsoiler + moldboard plough—T₃) and establishment (soil puddling + transplanting—TPR, direct seeding—DSR) combinations on soil physical properties over two cycles of the rice–wheat rotation. For the rice season, 0–20 cm saturated hydraulic conductivity (K_sat) in the DSR plots was 2.6 and 4.3 times higher than their TPR counterparts in the first (Y₁) and second (Y₂) years, respectively (TPR-Y₁ = 93 mm day⁻¹, DSR-Y₁ = 241 mm day⁻¹, TPR-Y₂ = 133 mm day⁻¹, DSR-Y₂ = 582 mm day⁻¹), whereas tillage method did not significantly influence K_sat in this soil layer. The impact of rice establishment method was reflected in higher TPR bulk densities in the 5–10 (DSR = 1.19 g cm⁻³, TPR = 1.24 g cm⁻³) and 10–15 cm (DSR = 1.24 g cm⁻³, TPR = 1.29 g cm⁻³) depth increments in the wet season. Although none of the treatments significantly influenced the position or thickness of the plough sole, penetration resistance profiles suggest that vertical fractures with reduced soil strength were created within the pan region by deep tillage (T₂ and T₃), although these features were not associated with higher hydraulic conductivities from 20 to 50 cm. As the soils dried at the end of the rice season, crack propagation in the deep tilled plots (T₂ and T₃) was more pervasive. During the wheat season, comparable bulk density profiles and soil moisture retention characteristics across the treatments suggest that many of the edaphic changes induced by contrasting rice tillage and establishment practices did not persist in the self-mulching, vertic soils at our site. Conversely, significant increases in K_sat among the DSR plots from Y₁ to Y₂ (Y₁ = 241 mm day⁻¹, Y₂ = 582 mm day⁻¹) imply a temporal element to soil structural regeneration with adoption of direct seeding.     

Using the simplified falling head technique to detect temporal changes in field-saturated hydraulic conductivity at the surface of a sandy loam soil

Determining temporal changes in field-saturated hydraulic conductivity (K_fs) is important for understanding and modeling hydrological phenomena at the field scale. Little is known about temporal variability of K_fs values measured at permanent sampling points. In this investigation, the simplified falling head (SFH) technique was used for an approximately 2-year period to determine temporal changes in K_fs at 11 permanent sampling points established at the surface of a sandy loam soil. Additional K_fs measurements were obtained by the single-ring pressure infiltrometer (PI) technique to also compare the SFH and PI techniques. The lowest mean values of K_fs, M(K_fs), were detected in December and January (20.5 ≤ M(K_fs) ≤ 146.2 mm h⁻¹), whereas higher results (190.5 ≤ M(K_fs) ≤ 951.9 mm h⁻¹) were obtained in the other months of the year. The K_fs values were higher and less variable in the dry soil (θ_i ≤ 0.21 m³ m⁻³, M(K_fs) = 340.6 mm h⁻¹, CV(K_fs) = 106%) than in the wet one (θ_i > 0.21 m³ m⁻³, M(K_fs) = 78.4 mm h⁻¹, CV(K_fs) = 185%). Both wet and dry soil were less conductive at the end of the study period than at the beginning one but a more appreciable change was detected for the dry soil (K_fs decreasing by 83.4%) than for the wet one (K_fs decreasing by 63.0%). The simple SFH technique yielded K_fs results similar to the more laborious and time-consuming PI technique (i.e., mean values differing at the most by a factor of two). It was concluded that (i) the soil water content was an important factor affecting the K_fs results obtained in a relatively coarse-textured soil, (ii) the impact of time from the beginning of the experiment on the saturated hydraulic conductivity was larger for a repeated sampling of dry soil than of wet soil and (iii) the SFH technique yielded reliable K_fs results in a relatively short period of time without the need for extensive instrumentation or analytical methodology.     

Water infiltration and soil structure related to organic matter and its stratification with depth

Soil organic matter is a key attribute of soil quality that impacts soil aggregation and water infiltration. Two soils (Typic Kanhapludults), one under long-term management of conventional tillage (CT) and one under long-term management of no tillage (NT), were sampled to a depth of 12 cm. Soil cores (15 cm diameter) were either left intact or sieved and repacked to differentiate between short-term (sieving) and long-term (tillage management) effects of soil disturbance on water infiltration, penetration resistance, soil bulk density, macroaggregate stability, and soil organic carbon (SOC). Mean weekly water infiltration was not different between sieved and intact cores from long-term CT (22 cm h⁻¹), but was significantly greater in intact (72 cm h⁻¹) than in sieved (28 cm h⁻¹) soil from long-term NT. The stratification ratio of SOC (i.e., of 0–3 cm depth divided by that of 6–12 cm depth) was predictive of water infiltration rate, irrespective of short- or long-term history of disturbance. Although tillage is used to increase soil porosity, it is a short-term solution that has negative consequences on surface soil structural stability, surface residue accumulation, and surface-SOC, which are critical features that control water infiltration and subsequent water transmission and storage in soil. The stratification ratio of SOC could be used as a simple diagnostic tool to identify land management strategies that improve soil water properties (e.g., infiltration, water-holding capacity, and plant-available water).     

Soil physical properties and soybean (Glycine max, Merrill) root abundance in conventionally- and zero-tilled soils in the humid Pampas of Argentina

In the humid Pampas of Argentina soybean is cultivated in different soil types, which were changed from conventional- to zero tillage systems in the last decade. Little is known about the response of soybean roots to these different soil physical environments. Pasture, and conventionally- and zero-tilled field lots cropped to soybean (R1 and R2 ontogenic stages) were sampled in February–March 2001 in a sandy clay loam and two silty clay loam Mollisols, and in a clayey Vertisol. In the 0–0.05 m layer of conventionally- and zero-tilled lots soil organic carbon represented 53–72% of that in pasture lots, and showed an incipient recovery after 4–11 years of continuous zero tillage. Soil aggregate stability was 10.1–46.8% lower in conventionally-tilled than in pasture lots, and recovered completely in zero-tilled lots. Soil relative compaction ranged 60.8–83.6%, which was below the threshold limit for crop yields (>90%). In change, soil porosity >50 μm ranged 0.91–5.09% soil volume, well below the minimum critical limit for root aeration and elongation (>10%, v/v). The threshold of soil resistance (about 2–3 MPa) was only over passed in an induced plough pan in the conventionally-tilled Bragado soil (5.9 MPa), and in the conventionally- and zero-tilled Ramallo soils (3.7–4.2 MPa, respectively). However, neither the low macroporosity nor the high soil resistances impeded soybean roots growth in any site. According to a fitted polynomial function, root abundance was negatively related to clay content in the subsoil (R² = 0.84, P < 0.001). Soybean roots were only abundant in the subsoil of the sandy clay loam Mollisol, which had <350 g kg⁻¹ clay. Results show that subsoil properties, and not tillage systems, were the primary effect of root growth of soybean.     

Field compaction at different soil-water status: effects on pore size distribution and soil water characteristics of a Rhodic Ferralsol in Western Cuba

The level of compaction induced on cultivated fields through trafficking is strongly influenced by the prevailing soil-water status and, depending on the attendant soil degradation, vital soil hydraulic processes could be affected. Therefore, understanding the relationship between field soil-water status and the corresponding level of induced compaction for a given load is considered an imperative step toward a better control of the occurrence of traffic-induced field soil compaction. Pore size distribution, a fundamental and highly degradable soil property, was measured in a Rhodic Ferralsol, the most productive and extensively distributed soil in Western Cuba, to study the effects of three levels of soil compaction on soil water characteristic parameters. Soil bulk density and cone penetration index were used to measure compaction levels established by seven passes of a 10 Mg tractor at three soil-water statuses corresponding to the plastic (Fs), friable (Fc) and relatively dry soil (Ds) consistency states. Pore size distribution calculated from soil water characteristic curves was classified into three pore size categories on the basis of their hydraulic functioning: >50 μm (f_>50 μm), 50–0.5 μm (f_{50–0.5 μm}) and <0.5 μm (f_<0.5 μm). The greatest compaction levels were attained in the Fs and Fc soil water treatments, and a significant contribution to compaction was attributed to the existing soil water states under which the soil compaction was accomplished. Average cone index (CI) values in the range of 2.93–3.70 MPa reflected the accumulation of f_<0.5 μm pores, and incurred severe reductions in the volume of f_>50 μm pores in the Fs and Fc treatments, while an average CI value of 1.69 MPa indicated increments in the volume of f_{50–0.5 μm} in the Ds treatment. Despite the differential effects of soil compaction on the distribution of the different pore size categories, soil total porosity (f_Total) was not effective in reflecting treatment effects. Soil water desorption at the soil water potentials evaluated (0.0 to −15,000 cm H₂O) was adversely affected in the f_<0.5 μm dominated treatments; strong soil water retention was observed with the predominance of f_<0.5 μm, as was confirmed by the high water content at plant wilting point. Based on these findings, the use of field capacity water content as the upper limit of plant available soil water was therefore considered inappropriate for compacted soils.     

Persistence of soil compaction due to high axle load traffic. II. Long-term effects on the properties of fine-textured and organic soils

The long-term effects of high axle load traffic on soil structure were investigated in three field experiments. Two of the experiments were located on fine-textured mineral soils (Vertic Cambisol). The clay soil had 48 g clay (particle size less than 2 μm) per 100 g in the topsoil and 65 g per 100 g in the subsoil, and the loam soil had clay contents of 30 g and 42 g per 100 g in the topsoil and subsoil, respectively. One experiment was located on an organic soil (Mollic Gleysol) consisting of well-decomposed sedge peat mixed with clay from 0.2 to 0.4–0.5 m depth, and underlain by gythia (organic soil with high clay content). In the autumn of 1981, one pass and four repeated passes with a heavy tractor-trailer combination compacted the soils to 0.4–0.5 m depth. The trailer tandem axle load was 19 Mg on the clay and 16 Mg on the other soils.

For 9 years after the experimental traffic, the main crops grown were spring cereals. During this time, the maximum axle load applied during field operations was 5 Mg and the maximum tyre inflation pressure was 150 kPa. The clay and loam froze to 0.5 m depth for 6 and 2 years, respectively. During several growing seasons all three soils dried and cracked. In the ninth year after the loading, soil penetrometer resistance, saturated hydraulic conductivity (K_sat), macroporosity and number and area of cylindrical biopores were measured and the visual structure of the soils examined.

Compaction in the plough layer was alleviated by ploughing and natural processes, whereas in the subsoil the effects of the compaction were still measurable, in all experiments, in the ninth year after the high axle load traffic. In the clay soil in the 0.3–0.5 m layer and in the organic soil in the 0.28–0.4 m layer, the penetrometer resistance was 22–26% greater and the soil structure more massive in the plots compacted with four passes than in the control plots. In the 0.4–0.55 m layer in all soils, the loading with four passes decreased K_sat by 60–98% and macroporosity (diameter greater than 300 μm) by 37–70%. In the fine-textured mineral subsoils, cylindrical biopores were found in all treatments. The trend of the results was, however, for biopores to be fewer in compacted than in control plots.     

Soil failure associated with crack propagation for an agricultural tillage tool

Tillage loosens soil to depths of 75–150 mm (3–6 in.). As the soil is tilled, the failure path precedes the motion of the tillage tool. Previous studies have examined soil forces acting on a tine by predicting different soil failure patterns. This paper quantifies the rate and the path of the cracks associated with soil failure front. The propagation of the soil failure path by observing the temporal profile of the leading edge of the failure crack with respect to the tool motion was examined. Crack propagations were analysed for sweep operating at 4 km h⁻¹ speed, and two operating depths of 75 and 100 mm using high-speed digital videography. Higher depth of operation showed distinct phases for crack development and propagation. Short and intermittent soil crack propagation with lower propagation growth rates was observed for shallow depth of operation. Crack growth rate has been observed to have a sinusoidal relation with time.     

Soil management by shallow mouldboard ploughing in The Netherlands

The structure of the soil in the arable layer is controlled by tillage, soil biota activities and weathering, whereas the structure below this layer is mainly the result of the activities of soil biota. Organic farmers tend to minimise the depth of the main tillage operation to encourage soil biota to create a soil structure with continuous biopores and a well crumbled topsoil. The best main tillage operation for preventive weed control, especially important in organic farming, is mouldboard ploughing. The shallow ploughing experiments described in this paper were conducted to ascertain the minimum ploughing depth for an ecologically accountable, sustainable tillage system with good weed control, good land qualities (in terms of workable days, aeration and soil moisture conditions) and finally with good yields. The “ecoplough” used for shallow ploughing was developed by Rumptstad Industries to meet the requirements of relatively shallow ploughing with good soil inversion for weed control. The plough has seven or eight bottoms for ploughing depths of 0.12–0.20 m, a working width of 2.1 m and a working speed of 1.7 m s⁻¹. Its width is such that the tractor with wide low-pressure tyres runs on top of the land.

After using the plough for 6 years on Luvisols (>200 gkg⁻¹<2 μm) in the IJsselmeer polders and on Luvisols (120–160 gkg⁻¹<2 μm) in polders near the northern coast of The Netherlands, it was found that compared with conventional ploughing, shallow ploughing required less energy and labour and produced a relatively smooth surface. The latter facilitates the preparation of a seedbed consisting of relatively fine, strong, stable and moist aggregates. Organic matter, soil biota and nutrients were concentrated higher in the profile, influencing the workability of the soil, the growth of weeds and the growth of crops. Most of the yields were similar to yields after conventional ploughing, but weed populations increased when ploughing depth was <0.2 m. It was concluded that for organic farming on “active” soils (soils subject to shrink/swell with >200 g kg⁻¹<2 μm), shallow ploughing seems to be the best reduced tillage system. It has several advantages. The main factor determining the minimum ploughing depth is control of weeds, especially of perennials.     

Disc harrowing intensity and its impact on soil properties and plant growth of agropastoral systems in the Llanos of Colombia

Oxisols such as those of the Colombian Eastern Plains (Llanos) are susceptible to physical, chemical and biological degradation once brought into cultivation, especially under intensive use of machinery. The main objective of this study was to determine the impact of intensive disc harrowing (2, 4 or 8 disc harrow passes per year over 3 years) on soil physical and chemical properties, soil phosphorus dynamics, plant growth and nutrient acquisition of contrasting agropastoral systems on an Oxisol. The three main systems tested after 2 years of upland rice cultivation were grass-alone pasture (Brachiaria dictyoneura), green manure (Crotalaria juncea), and maize (Zea mays). Native savanna treatment was used as a control. Intensive disc harrowing improved macroporosity values of 0–5 cm soil layer up to 59% for grass-alone pasture system compared to native savanna. Disc harrowing significantly reduced bulk densities for pasture and green manure systems compared to the native savanna in the 0–5 cm soil layer. Intensive disc harrowing significantly improved volumetric moisture content of green manure and maize systems at 5–10 cm soil depth. The distribution of biologically, moderately and sparingly available P, organic P and total P varied under green manure, maize and grass-alone pasture systems. Two passes of disc harrow per year were sufficient for grass-alone pasture, while maize showed greater aboveground production and nutrient acquisition at 8 passes of disc harrow per year. The maize and green manure cropping systems were better than the grass-alone pasture system at separating the effect of increased number of disc harrow passes on soil physical and chemical characteristics.     

Influence of spring preparation date and soil water content on seedbed physical conditions of a clayey soil in Sweden

Secondary tillage performed under inadequate soil water contents usually leads to a poor seedbed. Under normal Swedish weather conditions, clayey soils ploughed during autumn form a very dry top layer in spring, which acts as an evaporation barrier so that deeper layers remain wet. Thus, the conventional approach considering soil workability in relation to a single value of soil water content is difficult to apply. Hence, a field experiment was carried out to study the effect of seedbed preparation date, the associated soil water contents and traffic consequences on the physical properties of a spring seedbed. The field was autumn ploughed and the experiment started as soon as the field was trafficable after winter thawing. The seedbed preparation consisted of three harrowing operations on plots 8 m×8 m (three replications) with a spring tined harrow and a tractor mounted with dual tyres and was performed on 10 occasions from the beginning of April to the middle of May. With the exception of some short periods after rain, the soil had a clear water stratification during the experiment, with a very dry superficial layer (5–20 mm thick) contrasting to water contents over 300 g kg⁻¹ from only 40 mm depth. After the harrowing operation, the seedbed aggregate fraction less than 2 mm increased from about 40% at the beginning of April to about 60% for the last four treatments in May. Contributing factors to the rise were attributed to the lower water contents of the top layer (<40 mm) and the drying–wetting and freezing–thawing cycles that occurred in the surface layer during April. There were no significant differences in bulk density after harrowing between the treatments but an increase in penetration resistance up to a depth of 180 mm in the harrowed plots was statistically significant (P<0.001). In the non-harrowed soil, penetration resistance also increased, including in those soil layers where water contents kept nearly constant.

In conclusion, the seedbed preparation dates had only a minor effect on soil compaction, as measured by bulk density and penetration resistance, due to the slow drying beneath the dry top layer. The fraction of fine aggregates in the seedbed increased with time. Thus, the optimal time for seedbed preparation depended mainly on soil friability and not on the risk of compaction.     

Impact of soil compaction upon soil water balance and maize yield estimated by the SIMWASER model

The capability of the soil water balance model SIMWASER to predict the impact of soil compaction upon the yield of maize (Zea mays L.) is tested, using the results of a field experiment on the influence of soil compaction by wheel pressure upon soil structure, water regime and plant growth. The experimental site was located on an Eutric Cambisol with loamy silt soil texture at an elevation of 260 m in the northern, semi-humid sub-alpine zone of Austria. Within the experimental field a 7 m wide strip was compacted by a tractor driven trailer just before planting maize in May 1988. Compression effects due to trailer traffic resulted in distinct differences of physical and mechanical soil parameters in comparison with the uncompressed experimental plots down to a depth of about 30 cm: bulk density and penetration resistance at field capacity were increased from 1.45 to 1.85 g/cm³, and from 0.8 to 1.5 MPa, respectively, while air-filled pore space as well as infiltration rate were appreciable lowered from about 0.08–0.02 cm³/cm³ and from 50 to 0.5 cm per day, respectively. The overall effect was a clear depression of the dry matter grain yield from 7184 kg/ha of the non-compacted plot to 5272 kg/ha in the compacted field strip. The deterministic and functional model SIMWASER simulates the water balance and the crop yield for any number of crop rotations and years, provided that daily weather records (air temperature, humidity of air, global radiation, wind and precipitation) are available. Crop growth and soil water regime are coupled together by the physiological processes of transpiration and assimilation, which take place at the same time through the stomata of the plant leaves and are both reacting in the same direction to changes in the soil water availability within the rooting zone. The water availability during rainless seasons depends on the hydraulic properties of the soil profile within the rooting depth and on rooting density. Rooting depth and density are affected by both the type of the crop and the penetration resistance of the soil, which depends on the soil moisture status and may be strongly increased by soil compaction. The model SIMWASER was able to simulate these effects as shown by the calculated grain yields, which amounted in the non-compacted plot to 7512 and to 5558 kg dry matter/ha in the compacted plot.     

Spatial variability of soil water content and mechanical resistance of Brazilian ferralsol

The spatial variability of mechanical resistance to penetration (PR) and gravimetric moisture (GM) was studied at a depth of 0–0.40 m, in a ferralsol cropped with corn, and under conventional tillage in Ilha Solteira, Brazil (latitude 20°17′S, and longitude 52°25′W). The purpose of this study was to analyse and to try explaining the spatial variability of the mentioned soil physical properties using geostatistics. Soil data was collected at points arranged on the nodes of a mesh with 97 points. Geostatistics was used to analyse the spatial variability of PR and GM at four depths: 0–0.1, 0.1–0.2, 0.2–0.3 and 0.3–0.4 m. PR showed a higher variability of data, with coefficients of variation of 52.39, 30.54, 16.91, and 15.18%, from the surface layers to the deepest layers. The values of the coefficients of variation for GM were lower: 9.99, 5.13, 5.59, and 5.69%. Correlation between GM and PR for the same soil layers was low. Penetration resistance showed spatial structure only in the 0.30–0.40 m layer, while gravimetric moisture showed spatial structure at all depths except for 0–0.10 m. All the models of fitted semivariograms were spherical and exponential, with ranges of 10–80 m. Data for the variable ‘GM’ in the 0.20–0.30 and 0.30–0.40 m layers revealed a trend in data attributed to the occurrence of subsurface water flow.     

Effects of mechanical energy inputs on soil respiration at the aggregate and field scales

Cultivation machinery applies large amounts of mechanical energy to the soil and often brings about a decrease in soil organic carbon (SOC). New experiments on the effects of mechanical energy inputs on soil respiration are reported and the results discussed. In the laboratory, a specific energy, K, of 150 J kg⁻¹, similar to that experienced during typical cultivation operations, was applied to soil aggregates using a falling weight. Respiration (carbon dioxide, CO₂ emission) of the samples was then measured by an electrical conductimetric method. Basal respiration (when K=0) measured on Chromic Luvisol aggregates, was found to increase with increasing SOC, from 1.88 μg CO₂ g⁻¹ h⁻¹ for a permanent fallow soil (SOC=11 g kg⁻¹) to 8.25 μg CO₂ g⁻¹ h⁻¹ for a permanent grassland soil (SOC=32 g kg⁻¹). Basal respiration of a Calcic Cambisol, more than doubled (2.0–5.2 μg CO₂ g⁻¹ h⁻¹) with increasing gravimetric soil water contents. Mechanical energy inputs caused an initial burst of increased respiration, which lasted up to 4 h. Over the following 4–24 h period, arable soils with lower SOC contents, (11–21 g kg⁻¹), respiration rates dropped back to a level, approximately 1.14 times higher than the basal value. However, grassland soils with higher SOC contents (28–32 g kg⁻¹), increases in this longer-term respiration rate following 150 J kg⁻¹ of energy, were negligible. A field experiment, in which CO₂ was measured by infra-red absorption, also showed that tillage stimulated increased levels of soil respiration for periods ranging from 12 h to more than one week. The highest respiration rates, 80 mg CO₂ m⁻² h⁻¹ were associated with high energy, powered tillage on clay soils. On the same soil, low energy draught tillage resulted in a respiration rate of approximately half this value. The results of these experiments are discussed in relation to equilibrium levels of soil organic matter. The application of known quantities of mechanical energy to soil aggregates under laboratory conditions, in order to simulate the effect of different cultivation practices, when combined with the subsequent measurement of soil respiration, can provide useful indication of the likely consequences of soil management on SOC.     

Soil fertility properties on Agave angustifolia Haw. plantations

This study examined the variations in soil physical, chemical and biological properties from Agave angustifolia fields in three sites with different topographic conditions (valley, hill and mountain), in Oaxaca, Mexico, associated with the tillage systems, disk ploughing (DP), animal drawn ploughing (ADP) and minimum tillage (MT), respectively. Plant ages were 1.5–3.5 years (class 1), 3.6–5.5 years (class 2) and 5.6–7.5 years (class 3). Soil samples were taken at two soil depths (0–20 and 21–40 cm) from plots of 4000 m² within each site and plant age classes, during the spring of 2005. The main changes in soil properties were found in the mountain site. Soil bulk density (2.0 g cm⁻³), cone penetration resistance (CPR) (3.96 MPa), 0.7 and 1.0 mm water stable aggregates (WSA) (28.3 g kg⁻¹ and 102.2 g kg⁻¹, respectively) were higher in the mountain site than in the hill and valley fields. This result is consistent with the rocky substrate beneath the shallow soil. Soil organic carbon (SOC) (23.9 g kg⁻¹), available N (23.1 mg kg⁻¹) and soil microbial biomass carbon (SMBC) (969.6 μg g⁻¹) at the mountain site showed the highest values, suggesting that MT practiced in this topographic condition favours the organic matter accumulation and biological activity. Soil microbial biomass carbon and SOC seem to be the soil properties that were mainly affected by the sites and soil management associated with them. For the three sites, SOC, P_Olsen, available N, exchangeable Na⁺ and SMBC were higher at 0–20 cm depth than at 21–40 cm depth within each site. Exchangeable Ca²⁺ and K⁺, P_Olsen and CPR increased with plant age. In contrast, available N decreased. Soil chemical properties were more affected by the age of the plant than physical and biological properties. Results reported here represent a reference of the fertility properties of soils cultivated with A. angustifolia, which could be used in further studies focused on management and tillage systems.     

Soil organic matter and related physical properties in a Mediterranean wheat-based rotation trial

Under semi-arid Mediterranean conditions, limited moisture is the main constraint to rainfed cropping with wheat (Triticum aestivum), barley (Hordeum vulgare), and food and forage legumes. With increasing land-use pressure, moisture-conserving fallowing is being replaced by continuous cropping, which is considered an unsustainable practice. Thus, a long-term trial with durum wheat (T. turgidum var. durum) was established in 1983 at Tel Hadya, Aleppo, Syria (mean annual rainfall 330 mm) to assess alternative rotation options to fallow and continuous cropping. Nitrogen (N) and grazing/residue management were secondary factors. Soil aggregation, infiltration, hydraulic conductivity, and total soil organic matter and component fractions (fulvic and humic acids and polysaccharides) were determined at the end of 12 years. Some rotations, e.g., medic (Medicago sativa) and vetch (Vicia faba), significantly increased soil organic matter (12.5–13.8 g kg⁻¹ versus 10.9–11 g kg⁻¹ for continuous wheat and wheat/fallow). All measurements, or indices, indicated parallel trends with increasing organic matter, e.g., coefficients of macro-structure, micro-aggregation, and water-stable aggregates, and decreasing dispersion. Similarly, legume rotations had higher infiltration rates (16.2–21.8 cm h⁻¹ versus 13.9–14.4 cm h⁻¹ with continuous wheat and wheat/fallow) and hydraulic conductivity rates (8.7–12.4 cm h⁻¹ versus 6.2–7.4 cm h⁻¹ with continuous wheat and wheat/fallow). We conclude that cereal/legume rotations, in addition to being biologically and economically attractive, also enhance soil quality and thus promote soil use sustainability in fragile semi-arid areas as in the Mediterranean zone.