Behaviour of the twill weave woven fabrics during relaxation

This work looks into the behaviour of the twill weave woven fabrics during relaxation (when the weaving tension is released). Ten, 50-metre rolls of twill weave woven fabrics were produced. The fabrics were marked in a rectangular form at the weaving loom. After 48 hours of relaxation, the new shapes and sizes were recorded. The shapes of almost all of the samples were changed to parallelogram, even though they differed in size. The work showed that the manner of fabric deformation during relaxation depends upon the fabric structure. It indicates that contraction due to relaxation of the twill weave causes the woven fabric to skew. in the direction of the twill. The quantity of the skewness is related to the float length andthe twill type. Fabrics with longer float length have higher skewness.     

The effect of weft density on the skewness of the twill weave woven fabric

This experimental study investigates the effect of weft density on the skewness of the twill weave woven fabrics. A total of 12 rolls of woven fabrics - 2/2, 3/3 and 4/4 - twill weave, with 20, 22, 24 and 26 weft densities were produced and their skewness due to relaxation was measured. The measured values show that as the weft density increases from 20 to 26, the skewness decreases from 2.4, 2.9, 3.6 to 1, 1.1 and 1.15 respectively. This decrease supports the idea that the increase in weft density drops the effect of the weave type on skewness. In fact, this experimental work reveals that increase in weft density lowers the free spaces between the floats, shortens the float length and raises the shearing rigidity of the fabric and as a result the ability of the warp floats’ in-plane lever to move and skew is lowered.     

Theoretical estimation of initial uniaxial tensile modulus in 2/2 twill woven structures

A theoretical analysis for predicting the tensile modulus of 2/2 twill woven fabrics in their initial state of uniaxial load-extension behavior is presented. For this purpose, the geometrical model which was proposed in our previous work was used. The mechanical analysis was performed by applying the strain energy method and Castigliano’s theorem. The proposed theory was compared and validated by applying into some experimental data.     

New insight into compressive shrinkage finishing in a garment company: The effects on physical,mechanical and colorimetric properties of cotton woven fabrics

Compressive shrinkage or compressive shrinkage finishing is one of the most important finishing procedures in the textile industry to improve the dimensional stability of cotton fabrics. Study of the physical and mechanical properties of compressive shrinkage finished fabrics could be useful for optimizing the treatment conditions. This research was carried out in a production line of a recognized garment company on cotton woven fabrics with two different woven patterns (twill and plain). The samples were first dyed with reactive and sulfur dyes in a jigger dyeing machine and finished with a silicone softener. The dried fabrics were then processed in a compressive shrinkage machine. Several physical and mechanical properties of the samples were evaluated including area shrinkage, crimp percentage, thickness, abrasion resistance, drapeability, mechanical and colorimetric properties. The results showed that the thickness of all treated samples increased due to compressive shrinkage. The fabrics were analyzed with a Martindale Abrasion Tester to determine the abrasion resistance. Interestingly, we noted an increase in the abrasion resistance. After the compressive shrinkage process, the strength of the plain woven fabrics decreased in the warp direction, but increased for twill woven cotton fabrics. On the contrary, the strength of all samples increased in the weft direction. Colorimetric evaluation of the samples showed that the effect of compressive shrinkage on the color of all samples was negligible.     

Evaluation of the structural properties of plain fabrics woven from various fibers using Peirce’s model

Peirce’s fabric model has been widely used to predict the structural behavior of various plain woven fabrics. The structure of plain woven fabric can be defined in terms of the warp yarn number, weft yarn number, warp fabric density, weft fabric density, warp crimp, and weft crimp. The warp and weft yarn diameters are calculated from the warp and weft yarn numbers, and the effective coefficient of the yarn diameter is defined by using this model. We have investigated structural properties, such as the effective coefficient of the yarn diameter, yarn crimp, and fabric thickness for two different fabrics in which the constituent yarns are assumed to be either incompressible or compressible. This model is also applied to various plain fabrics woven from cotton, rayon, wool, linen, nylon, acetate, polyester, and silk yarns.     

Enhanced visualization of simulated woven fabrics

The woven fabric graphics designed with available computer aided design (CAD) systems using different colored warp and weft yarns look quite different from the appearance of their actual fabrics. To enhance the visual effects of designed woven fabric graphics, this paper reports a modified CAD woven fabric system, which allows users to design a fabric using parameters including fabric weaves, yarn number, yarn material, fabric count, crimp shape of interwoven yarns, and illumination. This enhanced system can design both yarns and fabrics, and consider the transitional color effect around interweaving points of warp and weft yarns. Its simulation image quality of woven fabrics has been greatly improved, and several textile mills and universities are currently using this woven fabric design system.     

Evaluation of bamboo charcoal/stainless steel/TPU composite woven fabrics

Composite woven fabric satisfies what people require. Bamboo charcoal (BC) has been identified as a multifunctional material that has far-infrared ray, anions, deodorization and etc. BC fibers and yarns were made of bamboo charcoal powders and have further become a pervasive materials used in textile industry. In this study, cotton yarns, stainless steel/cotton (SS/C) complex yarn, bamboo charcoal/cotton (BC/C) complex yarns were woven into the plain, twill and Dobby composite woven fabrics. The warp yarn was composed of cotton yarns, and the weft yarn was made up of BC/C and SS/C complex yarns with a picking ratio of 1:1 and 3:1. Thermoplastic polyurethanes (TPU) film was then attached to the composite woven fabrics, forming the BC/SS/TPU composite woven fabrics. Tests of electromagnetic shielding effectiveness (EMSE), far-infrared emissivity, anions, water resistance, and water vapor permeability measured the single-layer, two-layer and four-layer composite woven fabrics, obtaining a far-infrared emissivity of 0.95 by 39.8 counts per minute, an anion count of 149 amount/cc, an EMSE of −11.87 dB under frequency of 900 MHz, a surface resistivity of 8×10⁻⁶ Ω/square, a water resistance of −8219 mmH₂O, and water vapor permeability of 989 g/m²·h and 319 g/m²·24 h in accordance with JIS L 1099 A1 and ASTM E96 BW.     

Effect of weaving process on tensile characterization of single and multiple ends of air-entangled textured polyester yarns

The tensile properties of air-entangled textured polyester single and multiple yarn ends before and after weaving were analyzed. The effects of weaving process considering fabric unit cell interlacement and number of yarn ends were evaluated by regression model. For this purpose, plain, ribs and satin woven fabrics were produced. The yarns were raveled from fabrics, and the tensile tests were applied to these yarns. The developed regression model showed that the number of interlacement and crimp ratio on the warp and weft yarns influence their tensile strength. Tensile strength of raveled yarns decreased compared to that of the bobbin yarn due to the effect of weaving process. This property degradation on the ravel yarns considered process degradation. Generally, when the number of warp and weft yarn ends increases, the warp and weft yarn tensile strengths for each fabric type decrease, whereas the warp and weft yarn tensile elongations slightly increase. The results from regression model were compared with the measured values. This study confirmed that the method in the study can be a viable and reliable tool. The research finding could be useful those who work on preform fabrication.     

Crimp analysis of worsted fabrics in the terms of fabric extension behaviour

Inside a woven fabric structure, warp and weft yarns acquire crimp as a result of yarns interlacing according to the weave pattern. Since warp and weft yarns are oriented in two perpendicular directions, applying tensile load in one direction causes extension in the load side and fabric contraction in the opposite direction. This process was investigated in this study by using an image processing procedure and it was found that fabric’s extension is in coincidence with yarn’s de-crimping process in the same direction. After the de-crimping stage, yarns in the load direction will be extended and at the same time crimp in the other direction will be increased, until jamming phenomenon happens in the fabric structure. The crimp interchange between warp and weft yarns follows a three-order polynomial function with a turning point in which the yarns in the load direction have no crimp.     

Assessment of the surface roughness of cotton fabrics through different yarn and fabric structural properties

The effects of some yarn properties (i.e. type, count, twist level, ply number, unevenness and crimp) and fabric constructional properties (i.e. cover, thickness and balance) on surface roughness values of cotton woven fabrics were investigated. A general overview of the results showed that surface roughness values of fabrics were affected from yarn and fabric properties and the effects were related to fabric balance, fabric cover (not cover factor), fabric thickness and crimp values of yarns in fabric structures. Surface roughness values of fabrics decreased as yarn fineness and yarn twist levels increased but as yarn ply number decreased. Also, surface roughness values gradually decreased from open-end yarn constituting fabrics to combed yarn constituting fabrics. Results showed that different properties of yarns caused changes in yarn crimps in fabric structure and also governed the changes in fabric balance, as well as changes in roughness of fabric surfaces. The changing properties of yarns and impact of these properties on fabric construction affected the formation of cotton fabric surfaces from smooth to coarse.     

The effect of fabric balance and fabric cover on surface roughness of polyester fabrics

The effects of fabric balance and fabric cover on surface roughness values of textured polyester woven fabrics with different constructional parameters were investigated. The warp yarn properties (type, count and warp density) were kept constant while the effect of variation in weft yarn density and weave pattern were studied. Measurements were conducted on pre-treated white fabric samples and the results assessed in relation to their constructional properties. A general overview of the results showed that surface roughness values of polyester fabrics affected by fabric balance and fabric cover and the effects were related to fabric thickness, yarn densities, yarn crimp, positioning of yarns in fabric structure. A change in weave pattern from sateen to plain increased the fabric balance and fabric cover, but decreased the surface roughness. Similarly, an increase in weft density increased the fabric balance and fabric cover, but decreased surface roughness. In order to produce fabrics with smooth surface properties yarn density should be increased, yarn float lengths decreased, cover of fabrics increased and fabric balance improved.     

Dimensional and physical properties of plain knitted fabrics made from 50/50 bamboo/cotton blended yarns

In this study, the dimensional and some physical properties of plain knitted fabrics made from 50/50 bamboo/cotton blended yarns are investigated. In order to see the differences and similarities, the results are then compared with those for similar fabrics knitted from 50/50 conventional viscose/cotton and 50/50 modal/cotton blended yarns. Each fabric type was produced with three different stitch lengths. After all fabrics were dyed under identical dyeing conditions, they were subjected to dry and full relaxation treatments. For dimensional properties of fabrics, course, wale and stitch densities were measured. Then, by calculating statistically best-fit lines passing both through the experimental points and the origin, dimensional constants i.e. k values were predicted in terms of the fiber types. The result show that each fabric type knitted from bamboo/cotton, viscose/cotton and modal/cotton blended yarns behaves in a similar manner. However, in both dry and fully relaxed states, the modal/cotton knitted fabrics tend to have slightly higher k values than the bamboo/cotton and viscose/cotton knitted fabrics. For physical properties, fabric weight per unit area, thickness, bursting strength, air permeability and pilling were evaluated. The results show that the weight, thickness and air permeability values are independent of the fiber type. Plain knitted fabrics from modal/cotton blended yarns have the highest bursting strength values. Plain knitted fabrics from bamboo/cotton blended yarns tend to pill less.     

Engineering design of woven fabrics using non-traditional optimization methods: A comparative study

This work aims to design woven fabrics with desired quality at optimum manufacturing cost by choice of suitable weaving parameters such as count, crimp and thread spacing of warp and weft yarns. To fulfill this goal, we endeavor to devise search based non-traditional optimization methods such as genetic algorithm, particle swarm optimization and simulated annealing for efficiently finding the appropriate combination of weave parameters. The quick response capability of the non-traditional optimization methods would benefit the fabric manufacturers for efficient determination of the required weaving parameters to produce the engineered fabrics. The experimental validation confirms that the particle swarm optimization is most suitable technique for engineering design of woven fabrics.     

An experimental investigation into the mechanical behaviour of 3D woven fabrics for structural composites

3D woven composites provide efficient delamination suppression, enhanced damage tolerance, superior impact, ballistic and blast performance characteristics over 2D fabric laminates. At the same time, this type of composites, having practically straight in-plane fibers, show significantly better in-plane stiffness and strength properties than respective properties of conventional composites. But, how the in-plane elastic and strength characteristics of this type of fabrics compare with respective in-plane properties of equivalent 2D woven fabrics. This paper presents a comprehensive experimental study of the comparison of in-plane tensile, bending, crimp interchange properties of UD, 2D, 3D orthogonal, 3D angle-interlock and 3D warp interlock multi-layer structures woven from E-glass tow. The results depict that the 3D woven fabrics have considerably superior mechanical properties with much lesser crimp compared to 2D fabrics.     

Assessing the relationship among fabric constructional parameters, fractional reflectances and cover factors of polyester fabrics by experimental and mathematical methods

This paper focuses on the assessment of the relation among constructional properties, fractional reflectances and cover factors of fabrics woven from polyester yarns. A novel equation for the calculation of the relation between fractional reflectance and fabric cover factor was proposed and the usage of the equation was assessed by reflectance measurements. 48 polyester fabrics having different constructional parameters were used and the fabrics differed from each other by their cover factors. The warp yarn type and count, warp density and warp yarn twist were the same but weft yarn count, weft yarn fiber count and weft density were different for the fabrics in the experimental sub-groups. The reflectance measurements were conducted on the pretreated but undyed fabric samples as well as on the individual yarn systems of the same fabrics. Fabrics with the same cover factors exhibited different fractional reflectances. Reflectances were found to be dependent on the cover factor as well as on yarn fiber fineness, yarn count, yarn density and fabric weave. The changes in crimp of the yarns according to different construction parameters also governed the changes in fractional reflectances of fabric surfaces. The proposed equation was tested according to different fabric construction parameters and it was concluded that fiber fineness and weave pattern were among the most important parameters which govern the total light reflectances from the fabric surfaces, although they are not incorporated in the calculation of the fabric cover factors. The proposed equation was used to explain the effects of these components on the reflectance behavior of the fabric surfaces and on fabric cover.     

A comparative study of cotton knitted fabrics and garments produced by the modified low twist and conventional ring yarns

Spirality is one of the major potential problems in knitted fabrics and garments. It affects the aesthetics and physical properties of the garment produced, such as the seam displacement, shape retention, pattern distortion and sewing difficulties. In this paper, a comparative study has been carried out to evaluate the physical performance of 100 % cotton knitted fabrics and garments produced by the modified low twist and conventional ring yarns through the actual wearing and washing trials. Experimental results showed that the properties of side seam displacement, fabric spirality, dimensional stability and skewness change of the T-shirts and sweaters made by the modified single yarns are comparable to those of garments made from the control plied yarns but much improved when compared to those from the control single yarns. In addition, the pilling resistance and bursting strength of the knitted fabrics made by the modified single yarns can still maintain a reasonably high level at a low yarn twist.     

A study on the structural properties of plain fabrics using the lenticular model

The structural properties of a plain fabric were considered using the lenticular model. The structure of a plain woven fabric can be defined in terms of warp yarn number, weft yarn number, warp fabric density, weft fabric density, warp crimp, and weft crimp. Many structural variables of the plain fabric could be calculated by the lenticular model using these terms. Also, this model can be used to explain the geometry of the flattened yarns that occur during the weaving process. Flattening factors of threads for various types of fibers were calculated, compared, and explained with the number of yarn twist. Flattening factors were found to affect the structural variables of the fabric such as fabric thickness, air permeability, and yarn crimp. Yarn crimp was also studied with variation of the structural variables of the fabric.     

Multifunctional melt-mixed Ag/TiO2 nanocomposite PP fabrics: Water vapour permeability, UV resistance, UV protection and wear properties

This research deals with the investigating the effect of nanoparticles on the various properties of nanocomposite fabrics produced from melt spinning of various blend ratios of prepared masterbatch containing Ag/TiO₂ nanoparticles. The results revealed that the wear properties of modified fabrics improved as compared to pure fabrics with a trend justified considering modulus or crystallinity of fabrics with opposite effects. About 40 % UV protection enhancement has been obtained applying this kind of nanoparticles in the close relationship with the crimp contraction of textured yarns. A considerable improvement in the garment comfort has been recorded for nanocomposite sample containing 1 wt% nanoparticles. The lower permeability at low environment temperature and a higher at higher one, as compared to the pure sample, were obtained using this sample. It is highly interesting that these desirable changes in permeability can be achieved in the range of common environment temperatures (15–35 °C) being adapted to the human body requirements. The changing point is about 25 °C exactly meeting the body requirements by changing environment temperatures. A UV-induced solid state nanocomposite interaction increasing wear properties of UV-irradiated nanocomposite fabrics has been discovered.     

A comparative study of finer conventional and modified cotton yarns and their resultant woven fabrics

A modified ring spinning technique has been recently developed by incorporating false twisting devices into the conventional ring frame. Its application on the coarser yarn counts (7–32 Ne) showed notable advantages in modified yarn and fabric performance. More recently, it was noted that this technique can also be applied for producing finer cotton yarns. Thus this paper aims to carry out a systematic study of the physical properties of the finer modified yarns (80 Ne) and woven fabrics with respect to the conventional ones. Physical properties of conventional and modified single yarns were evaluated and compared. These two types of single yarn were used for the production of woven fabrics. Moreover, the above two types of single yarn were also plied and used for the production of woven fabrics under a commercial condition. All woven fabrics were assessed in terms of fabric tensile strength, tearing strength, abrasion resistance, fabric weight, and air-permeability as well as other fabric performance measured by the Kawabata Evaluation System (KES). Experimental results showed that finer modified yarns and fabrics exhibit higher strength, lower hairiness, and improved abrasion resistance, slightly better compression property, and smoother surface with relatively larger thickness.     

Development of moisture transition ability on porous complex structured woven fabric with convergence of pattern,porosity, and plasma technology

A porous complex structured woven fabric was manufactured to maximize the moisture transition ability of the prepared fabric by increasing the absorptive property of the fabric through surface modification using plasma, which is a dry modification method. Porous single and complex structured woven fabrics were produced by applying pattern, porosity, and plasma technology, including fabric patterning based on the sheath/core complex structure, the formation of porosity by removing the weft thread or warp thread, and hydrophilic surface treatment using plasma and the improvement in water absorption of different fabrics by the porous and plasma treatment was investigated. Therefore, two different types of fabrics were prepared. One is the porous single structured FAB-SINGLE fabric which was taken out in the direction of the Polyester (PET) warp thread of a general single structure to form a porous. Another is FAB-COMPLEX fabrics that the water-soluble polylactic acid (PLA) yarns with a 1.7 to 2.0 times longer absorption distance than that of PET yarns were inserted into the weft threads, and the PLA yarns were dissolved in a solvent to form the porous complex fabric. And then the physical properties and water absorption of the two types of fabric were compared after the plasma treatment. The results showed that when the FAB-SINGLE fabric, which has porosity induced by the removal of the warp threads in a certain gap, was plasma treated for 5 min, the contact angle was decreased to the extent that a measurement of the contact angle was impossible, whereas the fabric that had not undergone a plasma treatment had a contact angle of 123.6 o. The contact angle of the FABCOMPLEX with porosity caused by the dissolution of the PLA yarns was reduced from 76.8 o to 0 o after 3 minutes of a lowtemperature plasma treatment, indicating that the hydrophilic property was increased. In addition, the water absorption measurements showed that the absorption height was increased from 2.3 cm of the fabric sample that had not been treated with plasma to the highest absorption height of 8.3 cm, suggesting that the water absorption also increased with the improvements in moisture transition ability by the plasma treatment. The physical tensile strength of the fabrics was not changed by the plasma treatment, despite the changes on the fabric surface, suggesting that the combination of double complex structures and the plasma treatment helped improve the water absorption.