Carbon dioxide emissions after application of tillage systems for a dark red latosol in southern Brazil

Soil tillage may influence CO₂ emissions in agricultural systems. Agricultural soils are managed in several ways in Brazil, ranging from no tillage to intensive land preparation. The objective of this study was to determine the effect of common soil tillage treatments (disk harrow, reversible disk plow, rotary tiller and chisel plow tillage systems) on the intermediate CO₂ emissions of a dark red latosol, located in southern Brazil. Different tillage systems produced significant differences in the CO₂ emissions, and the results indicate that the chisel plow produced the highest soil carbon loss during the 15 days period after tillage treatments were performed. Emissions to the atmosphere increased as much as 74 g CO₂ m⁻², at the end of a 2-week period, in the plot where the chisel plow treatment was applied, in comparison to the non-disturbed plot. The results indicate that the total increase on the intermediate term soil CO₂ emissions due to tillage treatments in southern Brazil is comparable to that reported for the more humid and cooler regions.     

Soil macroporosity,hydraulic conductivity and air permeability of silty soils under long-term conservation tillage in Indiana

With the increasing use of conservation tillage, many questions about the long-term effects of tillage system on soil physical properties have been raised. Studies were conducted to evaluate saturated hydraulic conductivity (K_SAT), macropore characteristics and air permeability of two silty soils as affected by long-term conservation tillage systems in the state of Indiana. Measurements were taken during the tenth year of a tillage study on a Chalmers silty clay loam (Typic Haplaquoll) and the fifth year of a study on a Clermont silt loam (Typic Ochraqualf). Tillage systems were moldboard plow, chisel, ridge till-plant, and no-till in a rotation of corn (Zea mays L.) and soya beans (Glycine max L.). Saturated hydraulic conductivity was measured on large soil columns (25 × 25 × 40 cm) before spring tillage, and macropore size and continuity were assessed with staining techniques. Intact soil cores (8 cm diam × 10 cm) were collected in early July in the row and non-trafficked interrow at three depths (10–20, 20–30, and 30–40 cm) and were analyzed for air permeability (K_air), air-filled porosity and bulk density. Saturated hydraulic conductivity values were in the order plow > chisel > ridge till > no-till for the Chalmers soil and were significantly greater in the plow treatment than in the other 3 tillage systems on the Clermont soil. Differences in K_SAT between the 2 soils were generally greater than differences among tillage systems, and coefficients of variation were lower for treatments that did not include may fall tillage operations. At the 10-cm depth on the Chalmers soil, the chisel treatment had the greatest number of stained cylindrical channels, whereas for the Clermont soil the ridge till had the greatest number at this depth. Although the no-till treatment had similar or fewer total channels, it had the most continuous channels from the 10-cm depth to the 20- and 30-cm depths on both soils. Tillage system, row position and depth all affected K_air. On the Chalmers soil, plow, chisel and ridge systems had lower K_air between rows than in the row at the 10–20-cm depth, whereas no-till had constant K_air in the row and between the row. On the Clermont soil, ridge till had the highest K_air of all treatments at the 10–20-cm depth, and no-till had the highest K_air of all treatments at the 20–30-cm depth.     

Tillage and straw management for modifying physical properties of a subarctic soil

Conservation tillage practices are intended to minimize soil erosion. Yet little is known concerning changes in physical properties of subarctic soils subject to tillage practices. This study ascertained whether physical properties of a newly cleared subarctic soil are altered after 7 years of continuous barley (Hordeum vulgare L.) using different tillage and straw management strategies. Tillage and straw treatments were established in 1983 near Delta Junction, Alaska, and consisted of conventional fall and spring disk, fall chisel plow, spring disk, and no-tillage. Tillage plots were split by straw management practices, which included straw and stubble, stubble only, and no straw or stubble. Soil samples were collected from the upper 0.15 m of the profile in the spring of 1990 to assess water content, bulk density, saturated hydraulic conductivity, dry aggregate and mechanical stability, penetration resistance, water retention, and particle size distribution. Percent non-erodible aggregates, mechanical stability, and penetration resistance were greater for no-tillage compared to conventional tillage, chisel plow, and spring disk. No-tillage soils were also typically wetter, denser, and had a greater hydraulic conductivity. The spring disk treatment was least susceptible to erosion and also conserved soil water compared with chisel plow. Straw maintained on the surface conserved water and promoted soil stability.     

Earthworm populations and growth rates related to long-term crop residue and tillage management

Conventional tillage creates soil physical conditions that may restrict earthworm movement and accelerate crop residue decomposition, thus reducing the food supply for earthworms. These negative impacts may be alleviated by retaining crop residues in agroecosystems. The objective of this study was to determine the effects of various tillage and crop residue management practices on earthworm populations in the field and earthworm growth under controlled conditions. Population assessments were conducted at two long-term (15+ years) experimental sites in Québec, Canada with three tillage systems: moldboard plow/disk harrow (CT), chisel plow or disk harrow (RT) and no tillage (NT), as well as two levels of crop residue inputs (high and low). Earthworm growth was assessed in intact soil cores from both sites. In the field, earthworm populations and biomass were greater with long-term NT than CT and RT practices, but not affected by crop residue management. Laboratory growth rates of Aporrectodea turgida (Eisen) in intact soil cores were affected by tillage and residue inputs, and were positively correlated with the soil organic C pool, suggesting that tillage and residue management practices that increase the soil organic C pool provide more organic substrates for earthworm growth. The highest earthworm growth rates were in soils from RT plots with high residue input, which differed from the response of earthworm populations to tillage and residue management treatments in the field. Our results suggest that tillage-induced disturbance probably has a greater impact than food availability on earthworm populations in cool, humid agroecosystems.     

Tillage and residue management effects on β-glucosaminidase activity in soils

There is an increasing interest in assessing the effects of tillage systems and residue management on biochemical processes, especially enzyme activities, of soils. This study was carried out to investigate the effects of three tillage systems (no-till, chisel plow and moldboard plow) and four residue placements (bare, normal, mulch and double mulch) on the activity of N-acetyl-β-glucosaminidase (NAGase, EC 3.2.1.30) involved in C and N cycling in soils. The activity values were significantly affected by tillage and residue management practices, being greatest in soils with no-till/double mulch and least with no-till/bare and moldboard/normal. Also, they were the highest under no-till/ double mulch-treated soils. Linear regression analyses showed that the activity of NAGase was significantly correlated with organic C in the surface soils (r=0.89***) and with organic C content at different depths (r=0.97***). The NAGase activity values were significantly correlated with the arylamidase activity values of the soils (r=0.63**), suggesting that tillage and residue management practices have similar impacts on the activities of these enzymes. The activity of this enzyme decreased markedly with increasing depth of the surface soil (0-15 cm) of the no-till/ double mulch-treated plots.     

Biological soil properties in a long‐term tillage trial in Germany

After 37 years of different soil‐tillage treatments in a long‐term field experiment in Germany, a number of biological soil characteristics was measured. The field trial comprised six major treatments with different implements and various depths. In this paper, results from a comparison of long‐term use of a plow (to 25 cm depth), a chisel plow (to 15 cm depth), and no‐tillage are presented. The biological soil characteristics measured include the soil‐organic‐carbon (SOC) content, microbial biomass, enzyme activities, and the abundance and biomass of earthworms. Long‐term use of a chisel plow and no‐tillage increased the organic‐C content in the uppermost soil layer (0–10 cm) compared with the plow treatment. The microbial biomass and the enzyme activities arginine‐ammonification, β‐glucosidase, and catalase decreased with depth in all treatments. Arginine‐ammonification and catalase were higher in the plow treatment in soil layers 10 to 30 cm. Additionally, the chisel plow caused an increase in number and biomass of earthworms compared to both other tillage treatments. Differences in earthworm numbers and biomass between plowing and no‐tillage were not statistically significant.     

Soil organic matter quality as influenced by tillage,lime, and phosphorus

In Eastern Canada, cereal yields are often restricted by soil acidity and low fertility. Continuous cereal production can also lead to soil structural degradation. The addition of lime and fertilizers and the adoption of conversation tillage practices are proposed solutions which may have a positive impact on soil quality. The objective of the present work was to assess the impact of 3 years of different tillage practices and P additions, and of a single lime addition on organic C and total N, microbial biomass C, and on N mineralization at the surface layer (0–7.5 cm) of a Courval sandy clay loam (Humic Gleysol). The easily mineralizable N, total amount of N mineralized in 22.1 weeks, the rate of N mineralization, and microbial biomass C were significantly greater in the minimum tillage than in the moldboard plow treatment. Chisel plow treatment showed intermediate values. The ratios of potentially mineralizable N and of easily mineralizable to total soil N were also significantly larger under minimum tillage and chisel plowing than under moldboard plowing. The lime and P treatments had no significant effect on the measured soil quality parameters. The total amount of N mineralized per unit of biomass C decreased as the tillage intensity increased, suggesting a decrease in the efficiency of the biomass in transforming organic N into potentially plant-available forms and thus a loss in soil organic matter quality. The results of this study indicate that conservation tillage practices such as rototilling and chisel plowing are efficient ways of maintaining soil organic matter quality when old pastures are brought back into cultivation.     

Quantifying seedbed condition using soil physical properties

Soil physical condition following tillage influences crop yield, but the desired condition cannot be adequately evaluated with current techniques. This study was conducted to determine a soil condition index (SCI) that could be used to select the type of implement needed to achieve an optimal seedbed with minimum energy input. Effects of bulk density, moisture content, and penetration resistance resulting from three tillage systems (no-till, chisel plow and moldboard plow), on the growth of corn (Zea mays L.) were studied. The experiment was conducted in Boone County, Ames, IA, on soils that are mostly Aquic Hapludolls, Typic Haplaquolls and Typic Hapludolls with slopes ranging from 0 to 5%. The results are from the 2000 season, which had normal weather conditions and yield levels for the Iowa state. The average corn grain yield at this site was 9.36 Mg/ha. At the V2 corn growth stage, the average dry biomass was 1.34 g per plant. The soil physical properties were normalized with respect to reference values and combined via multiple regression analysis against corn biomass at V2 stage into the SCI. Mean SCI values for the no-till, chisel and moldboard plow treatments were 0.86, 0.76, and 0.73, respectively, all with a standard error of 0.0127. The lower the SCI, the more optimum the soil physical conditions. An analysis of variance showed significant differences among mean SCI for each treatment (p-value=0.001). The use of the SCI could improve the tillage decision-making process in environments similar the one studied.     

Effect of tillage treatments on soil thermal conductivity for some Jordanian clay loam and loam soils

Soil thermal conductivity determines how a soil warms or cools with exchange of energy by conduction, convection, and radiation. The ability to monitor soil thermal conductivity is an important tool in managing the soil temperature regime to affect seed germination and crop growth. In this study, the temperature-by-time data was obtained using a single probe device to determine the soil thermal conductivity. The device was used in the field in some Jordanian clay loam and loam soils to estimate their thermal conductivities under three different tillage treatments to a depth of 20 cm. Tillage treatments were: no-tillage, rotary tillage, and chisel tillage. For the same soil type, the results showed that rotary tillage decreased soil thermal conductivity more than chisel tillage, compared to no-tillage plots. For the clay loam, thermal conductivity ranged from 0.33 to 0.72 W m⁻¹ K⁻¹ in chisel plowed treatments, from 0.30 to 0.48 W m⁻¹ K⁻¹ in rotary plowed treatments, and from 0.45 to 0.78 W m⁻¹ K⁻¹ in no-till treatments. For the loam, thermal conductivity ranged from 0.40 to 0.75 W m⁻¹ K⁻¹ in chisel plowed treatments, from 0.34 to 0.57 W m⁻¹ K⁻¹ in rotary plowed treatments, and from 0.50 to 0.79 W m⁻¹ K⁻¹ in no-till treatments. The clay loam generally had lower thermal conductivity than loam in all similar tillage treatments. The thermal conductivity measured in this study for each tillage system, in each soil type, was compared with independent estimates based on standard procedures where soil properties are used to model thermal conductivity. The results of this study showed that thermal conductivity varied with soil texture and tillage treatment used and that differences between the modeled and measured thermal conductivities were very small.     

Weed seed bank affected by tillage intensity for barley in Alaska

The weed seed bank of a long-term tillage study in subarctic Alaska was studied at the end of 10 years of continuous spring barley (Hordeum vulgare L.). Tillage treatments were: no-till, disked once (spring), disked twice (spring and fall), and chisel plow (fall). Soil cores were obtained from each tillage treatment and seeds were manually separated from soil after washing through sieves. Tillage treatment had a significant effect on seed density of shepherds purse (Capsella bursa-pastoris (L.) Medic.), cinquefoil (Potentilla norvegica L.), foxtail barley (Hordeum jubatum L.), and on total seed density. Seed density was higher for these species and total seed density was greater under no-till than under other tillage treatments. Seed density was higher near the soil surface under no-till and chisel plow treatments than under disked treatments, which helps explain the greater difficulty of controlling weeds under reduced tillage.     

Tillage and residue management effects on arylamidase activity in soils

Recent interest in soil tillage and residue management has focused on low-input sustainable agriculture. This study was conducted to investigate the effect of three tillage systems (no-till, chisel plow, and moldboard plow) and four residue placements (bare, normal, mulch, and double mulch) on a most recently detected enzyme in soils, arylamidase activity. This enzyme catalyzes the hydrolysis of an N-terminal amino acid from peptides, amides, or arylamides. Results showed that arylamidase activity is greatly affected by tillage and crop residue placement. The greatest activity was found with chisel/mulch, moldboard plow/mulch, and no-till/double mulch, and the lowest with moldboard plow/normal and no-till/bare. Arylamidase activity was significantly correlated with organic C (r=0.59**) and soil pH _CaCl2 (r=0.55**)_, and decreased with soil depth. Results of this work suggest that the activity of this enzyme is affected by soil management, and indicate its potential ecological significance because of its role in the N cycle.     

Twenty years of conservation tillage research in subarctic Alaska: II. Impact on soil hydraulic properties

Soil management practices are needed in the subarctic that stabilize the soil against the forces of wind and water as well as conserve soil water for crop production. There is a paucity of information, however, regarding the long-term effects of conservation tillage on soil hydraulic properties in subarctic Alaska. The objective of this study was therefore to characterize infiltration, water retention, and saturated hydraulic conductivity of a soil 20 years after establishing tillage and straw management treatments in interior Alaska. The strip plot experimental design, established on a silt loam and maintained in continuous barley (Hordeum vulgare L.), included tillage as the main treatment and straw management as the secondary treatment. Tillage treatments included no tillage, autumn chisel plow, spring disk, and intensive tillage (autumn and spring disk) while straw treatments included retaining or removing stubble and loose straw from the soil surface after harvest. Soil properties were measured after sowing in spring 2004; saturated hydraulic conductivity was measured by the falling-head method, infiltration was measured using a double-ring infiltrometer, and water retention was assessed by measuring the temporal variation in in-situ soil water content. No tillage resulted in greater saturated hydraulic conductivity and generally retained more water against gravitational and matric forces than other tillage treatments. Infiltration was greater in autumn chisel plow than other tillage treatments and was presumably suppressed in no tillage by an organic layer overlying mineral soil. Infiltration was also enhanced by retaining straw on rather than removing straw from the soil surface after harvest. No tillage is not yet a sustainable management practice in this region due to lack of weed control strategies. In addition, the formation of an organic layer in no tillage has important ramifications for the soil hydrological and thermal environment. Therefore, minimum tillage (i.e., autumn chisel plow or spring disk) appears to be a viable management option for maximizing infiltration in interior Alaska.     

Effects of N fertilizer treatments on biologically active N pools in soils under plow and no tillage

Studies assessing the effects of different tillage and N fertilizer management practices on distributions and amounts of various C and N pools in soil can provide information about the influence of such management on the quality of organic matter in agricultural soils. To assess the influence of management on soil quality, we characterized the organic matter by measurements of total N, organic C, microbial biomass N and active N in the 0–20cm profiles of soil from long-term field experiments containing plots under treatments of plow or no tillage and 0, 135, or 270kgNha^–1 fertilizer. Previous work had established that on the basis of the crop growth requirement of maize, these application rates of fertilizer N provide amounts of N that are deficient, sufficient, and excessive, respectively. The studies reported provide evidence that the sufficient amount of fertilizer N stimulated formation of the biologically active pools of N (biomass N and active N) in soils under no tillage treatments, but the excessive amount of fertilizer N tended to suppress these pools. The results demonstrated that these influences of excessive N fertilization were not reflected in distributions of total N or total organic C in soil profiles but became evident with the measurements of biologically active N. This suggests that such measurements can provide information related to the influence of different management practices on soil quality. Received: 30 November 1995     

Effect of tillage and residue management on enzyme activities in soils: III. Phosphatases and arylsulfatase

This study was carried out to investigate the effect of tillage and residue management on activities of phosphatases (acid phosphatase, alkaline phosphatase, phosphodiesterase, and inorganic pyrophosphatase) and arylsulfatase. The land treatments included three tillage systems (no-till, chisel plow, and moldboard plow) in combination with corn residue placements in four replications. The activities of these enzymes in no-till/double mulch were significantly greater than those in the other treatments studied, including no-till/bare, no-till/normal, chisel/normal, chisel/mulch, moldboard/normal, and moldboard/mulch. The effect of mulching on activities of phosphatases was not as significant as on activities of arylsulfatase. The lowest enzyme activities were found in soil samples form no-till/bare and moldboard/normal treatments, with the exception of inorganic pyrophosphatase, which showed the lowest activity in no-till/bare only. Among the same residue placements, no-till and chisel plow showed comparable arylsulfatase activity, whereas the use of moldboard plow resulted in much lower arylsulfatase activity. The activities of phosphatases and arylsulfatase were significantly correlated with organic C in the 40 soil samples studies, with r values ranging from 0.71*** to 0.92***. The activities of alkaline phosphatase, phosphodiesterase, and arylsulfatase were significantly correlated with soil pH, with r values of 0.85***, 0.78***, and 0.77***, respectively, in the 28 surface soil samples studied, but acid phosphatase and inorganic pyrophosphatase activities were not significantly correlated with soil pH. The activities of phosphatases and arylsulfatase decreased markedly with increasing soil depth and this decrease was associated with a decrease in organic C content. The activities of these enzymes were also significantly intercorrelated, with r values ranging from 0.50*** to 0.92***. Received: 4 October 1995     

Strip-tillage effect on seedbed soil temperature and other soil physical properties

The no-tillage system is perceived as having lower soil temperatures, wetter soil conditions, and greater surface penetration resistance compared with conventional and other conservation tillage systems. Concerns associated with the effect of the no-tillage system on certain soil physical properties (i.e. soil temperature, moisture, and compaction) prompted this study to evaluate the effect of an alternative tillage system, strip-tillage, on these physical properties, compared with chisel plow and no-tillage systems. The study was conducted on two Iowa State University research and demonstration farms in 2001 and 2002. One site was at the Marsden Farm near Ames, where the soils were Nicollet loam (Aquic Hapludolls) and Webster silty clay loam (Typic Haplaquolls). The second site was at the Northeast Research and Demonstration Farm near Nashua, where the soils were Kenyon loam (Typic Hapludolls) and Floyd loam (Aquic Hapludolls).Soil temperature increased in the top 5 cm under strip-tillage (1.2–1.4 °C) over no-tillage and it remained close to the chisel plow soil temperature. This increase in soil temperature contributed to an improvement in plant emergence rate index (ERI) under strip-tillage compared with no-tillage. The results show no significant differences in soil moisture status between the three tillage systems, although the strip-tillage soil profile has slightly greater moisture content than chisel plow. Moisture content through the soil profile particularly at the lower depths under all tillage treatments was greater than the plant available water (PAW). However, the changes in soil moisture storage were much greater with strip-tillage and chisel plow than no-tillage from post-emergence to preharvest at 0–30 and 0–120 cm. It was observed also that most change in soil moisture storage occurred between post-emergence and tasseling. Penetration resistance was similar for both strip-tillage and no-tillage, but commonly greater than chisel plow. In general, the findings show that strip-tillage can contribute effectively to improve plant emergence, similar to chisel plowing and conserve soil moisture effectively compared with no-tillage.     

Short-term organic matter mineralisation following different types of tillage on a Swedish clay soil

Reduced tillage is proposed as a method of C sequestration in agricultural soils. However, tillage effects on organic matter turnover are often contradictory and data are lacking on how tillage practices affect soil respiration in northern Europe. This field study (1) quantified the short-term effects of different tillage methods and timing on soil respiration and N mineralisation and (2) examined changes in aggregate size distribution due to different tillage operations and how these relate to soil respiration. The study was conducted on Swedish clay soil (Eutric Cambisol) and compared no-tillage with three forms of tillage applied in early or late autumn 2010: mouldboard ploughing to 20–22 cm and chisel ploughing to 12 or 5 cm depth. Soil respiration, soil temperature, gravimetric water content, mineral N and aggregate size distribution were measured. The results showed that respiration was significantly higher (P?<?0.001) in no-till than in tilled plots during the 2 weeks following tillage in early September. Later tillage gave a similar trend but treatments did not differ significantly. Soil tillage and temperature explained 56 % of the variation in respiration. In the early tillage treatment, soil respiration decreased with tillage depth. Mineral N status was not affected by tillage treatment or timing. Soil water content did not differ significantly between tillage practices and therefore did not explain differences in respiration. The results indicate that conventional tillage in early autumn may reduce short-term soil respiration compared with chisel ploughing and no-till in clay soils in northern Europe.     

Rainfall and tillage effects on soil structure after alfalfa conversion to maize on a clay loam soil in New York

Soil degradation is accelerated when perennial crops are converted to annual row crops, primarily due to increased soil disturbance from tillage. Subsequent heavy rainfall may induce soil settling, reduce macroporosity and increase hardsetting upon drying. An experiment involving plow and no-tillage and two simulated rainfall treatments (‘wet’ and ‘dry’) was conducted on Kingsbury clay loam soil in northern New York in 1992 and 1993 to study their effects on soil structure under maize (Zea mays L.) after conversion from alfalfa (Medicago sativa L.), and to evaluate the use of spectral analysis of micropenetrometer observations for studying soil aggregation. Undisturbed soil cores were collected from the row and trafficked and non-trafficked interrow positions at the 0.05 and 0.15 m depths and used for laboratory measurement of soil strength and pore system properties. These well-structured soils show a high contribution (up to 0.15 m³ m⁻³) of macropores to the total porosity of the soil. Soil strength was generally slightly higher for no-till (NT) than plow till (PT), although only significant in 1992. Soil strength in the surface layer did not change significantly with drying. Spectral density patterns did not show strong treatment effects, although distinct peaks reflect 3.0–3.5 mm stable structural units within macroaggregates. Simulated rainfall treatments and tillage treatments generally did not strongly affect measured soil properties, presumably due to stable soil structure. Structurally stable clay loam soils show little effect of tillage or settling on soil physical properties in the first years after alfalfa to maize conversion, and have good potential for long-term annual crop production if properly managed.     

Converting from no-tillage to pre-seeding tillage: Influence on weeds, spring wheat grain yields and N, and soil quality

On the Canadian prairies there has been a steady increase in no-till seeding coupled with more frequent cropping, facilitated by the greater use of snow management to increase stored soil water. Although no-till seeding can gradually improve soil conservation and soil quality, it may also increase the incidence of grassy weed infestations and thus cause more frequent use of costly herbicides, such as glyphosate. Our objective was to determine if no-till producers experiencing grassy weed problems could introduce pre-seeding tillage for a few years to more economically control perennial weeds, without adversely affecting grain yield and quality, and soil quality. An experiment in which spring wheat (Triticum aestivum L.) was grown for 9 years with no-tillage management on an Orthic Brown Chernozem (Typic Haplobroll) with treatments involving snow management and N rate, placement and timing, was converted to a study of pre-seeding shallow (5–7.5 cm) tillage with a cultivator, versus no-tillage, by replacing the N timing treatment in the tenth year. The experiment was then continued for three more years, during which we assessed the effect of tillage on weed populations, grain yield and N content, and on soil quality. Soil quality was also assessed following one more year during which the entire study site was summerfallowed and subjected to four tillage operations. Weed populations generally were not affected by tillage or snow management treatments, but differed among N rate and placement treatments, though not in a way that could be easily interpreted. Tillage had no effect on yield or grain N content. It increased the erodible fraction of soil (dry sieving), but did not affect wet aggregate stability. Neither microbial biomass C, nor C and N mineralization were affected by the change in tillage method. We conclude that the judicious use of shallow pre-seeding tillage in an otherwise no-till cropping system can be tolerated to manage persistent grassy weed problems without deleteriously influencing soil quality, grain yield or protein.     

Soil carbon and nitrogen accumulation with long-term no-till versus moldboard plowing overestimated with tilled-zone sampling depths

Numerous investigators of tillage system impacts on soil organic carbon (OC) or total nitrogen (N) have limited their soil sampling to depths either at or just below the deepest tillage treatment in their experiments. This has resulted in an over-emphasis on OC and N changes in the near-surface zones and limited knowledge of crop and tillage system impacts below the maximum depth of soil disturbance by tillage implements. The objective of this study was to assess impacts of long-term (28 years) tillage and crop rotation on OC and N content and depth distribution together with bulk density and pH on a dark-colored Chalmers silty clay loam in Indiana. Soil samples were taken to 1 m depth in six depth increments from moldboard plow and no-till treatments in continuous corn and soybean–corn rotation. Rotation systems had little impact on the measured soil properties; OC content under continuous corn was not superior to the soybean–corn rotation in either no-till or moldboard plow systems. The increase in OC (on a mass per unit area basis) with no-till relative to moldboard plow averaged 23 t ha⁻¹ to a constant 30 cm sampling depth, but only 10 t ha⁻¹ to a constant 1.0 m sampling depth. Similarly, the increase in N with no-till was 1.9 t ha⁻¹ to a constant 30 cm sampling depth, but only 1.4 t ha⁻¹ to a constant 1.0 m sampling depth. Tillage treatments also had significant effects on soil bulk density and pH. Distribution of OC and N with soil depth differed dramatically under the different tillage systems. While no-till clearly resulted in more OC and N accumulation in the surface 15 cm than moldboard plow, the relative no-till advantage declined sharply with depth. Indeed, moldboard plowing resulted in substantially more OC and N, relative to no-till, in the 30–50 cm depth interval despite moldboard plowing consistently to less than a 25 cm depth. Our results suggest that conclusions about OC or N gains under long-term no-till are highly dependent on sampling depth and, therefore, tillage comparisons should be based on samples taken well beyond the deepest tillage depth.     

Earthworm response to rotation and tillage in a Missouri claypan soil

 Agricultural management practices affect earthworm populations. A field experiment was conducted to determine the effect of two rotations and two tillage systems on earthworm population density and biomass in a claypan soil. The rotations were soybean/corn and wheat/corn, and the tillage systems were conventional tillage (chisel plowed and disked) and no-tillage. Earthworm and soil samples were collected in fall 1995, spring 1996, and fall 1996. Aporrectodea trapezoides and Diplocardia singularis were the species identified at the site. A. trapezoides accounted for 92–96% of the total earthworm population density and D. singularis accounted for only 4–8%. In a no-till system, soybean/corn rotation resulted in significantly greater population density of A. trapezoides compared with the wheat/corn rotation. Crop residue quality (low C:N ratio) and quantity were important factors in increasing A. trapezoides population density and biomass. Conventional tillage markedly decreased population density and biomass of both earthworm species. Our results suggest that rotation and tillage significantly affect earthworm population density and biomass. Received: 6 June 1998