Impact of soil water stress on Nigellone oil content of black cumin seeds grown in calcareous-gypsifereous soils

Nigellone (dithymoquinone) is the main active constituent of volatile oil of black cumin (Nigella sativa) seeds. It is presently used in traditional medicines, for culinary as ornamentals, and is also considered for its abundant nectar secretion. While black cumin, investigated recently (for the oil, essential oil, and other biologically active constituents of their seeds) the effects of deficit irrigation on seeds Nigellone content produced on gypsifereous soils are not known. Randomized complete block design experiments were conducted with three replications and four irrigation treatments on soils with five different gypsum contents over two growing seasons (2008-2009 and 2009-2010). These experiments aim to monitor and quantify water stress and Nigellone volatile oil content of black cumin as a function of crop water stress index and soil gypsum content. The soil gypsum content treatments were 60.0 (G₁), 137.6 (G₂), 275.2 (G₃), 314.2 (G₄) and 486.0 (G₅) g kg⁻¹. Three irrigation treatments were based on replenishing the 0.60 m deep root zone to field capacity when the maximum allowable depletion (MAD) of the available soil water holding capacity of 25% (I₁), 50% (I₂) and 75% (I₃) were maintained in the crop experiments. A dryland treatment (fully stressed, I₄) was also included. The lower (non-stressed) and upper (stressed) baselines were measured to calculate crop water stress index. The crop water stress index behaved as expected, dropping to near zero following an irrigation and increasing gradually as black cumin plants depleted soil water reserves. The seasonal mean values of crop water stress index for the irrigation treatments; I₁, I₂, and I₃ were increased from 0.189, 0.287, 0.380 to 0.239, 0.366, 0.467, respectively when the soil gypsum content increased from 60.0 to 486.0 g kg⁻¹. The highest Nigellone volatile oil content of black cumin seeds was obtained for G₁I₁ treatment (5.1 g kg⁻¹) while the lowest content (3.5 g kg⁻¹) was obtained for G₅I₁ treatment. Equations that can be used to predict the Nigellone volatile oil content of black cumin seeds were developed for the three irrigation schedules of different maximum allowable depletion of available soil water holding capacity using the relationships between the Nigellone volatile oil content and the seasonal mean crop water stress index for different soil gypsum contents. The relationships between black cumin seed yield, Nigellone volatile oil content and seasonal mean crop water stress index values were primarily linear. These relations can be used to predict the yield of black cumin seeds, seeds Nigellone volatile oil content, and irrigation timing in soils with different soil gypsum contents. Thus, the obtained data will be beneficial for further research.     

Increasing water productivity of irrigated crops under limited water supply at field scale

Borkhar district is located in an arid to semi-arid region in Iran and regularly faces widespread drought. Given current water scarcity, the limited available water should be used as efficient and productive as possible. To explore on-farm strategies which result in higher economic gains and water productivity (WP), a physically based agrohydrological model, Soil Water Atmosphere Plant (SWAP), was calibrated and validated using intensive measured data at eight selected farmer fields (wheat, fodder maize, sunflower and sugar beet) in the Borkhar district, Iran during the agricultural year 2004-2005. The WP values for the main crops were computed using the SWAP simulated water balance components, i.e. transpiration T, evapotranspiration ET, irrigation I, and the marketable yield Y_M in terms in terms of Y_MT⁻¹, Y_M ET⁻¹ and Y_M I⁻¹.The average WP, expressed as $ T⁻¹ (US $ m⁻³) was 0.19 for wheat, 0.5 for fodder maize, 0.06 for sunflower and 0.38 for sugar beet. This indicated that fodder maize provides the highest economic benefit in the Borkhar irrigation district. Soil evaporation caused the average WP values, expressed as Y_M ET⁻¹ (kg m⁻³), to be significantly lower than the average WP, expressed as Y_MT⁻¹, i.e. about 27% for wheat, 11% for fodder maize, 12% for sunflower and 0.18 for sugar beet. Furthermore, due to percolation from root zone and stored moisture content in the root zone, the average WP values, expressed as Y_MI⁻¹ (kg m⁻³), had a 24-42% reduction as compared with WP, expressed as Y_M ET⁻¹.The results indicated that during the limited water supply period, on-farm strategies like deficit irrigation scheduling and reduction of the cultivated area can result in higher economic gains. Improved irrigation practices in terms of irrigation timing and amount, increased WP in terms of Y_MI⁻¹ (kg m⁻³) by a factor of 1.5 for wheat and maize, 1.3 for sunflower and 1.1 for sugar beet. Under water shortage conditions, reduction of the cultivated area yielded higher water productivity values as compared to deficit irrigation.     

Comparisons of energy balance and evapotranspiration between flooded and aerobic rice fields in the Philippines

The seasonal and annual variability of sensible heat flux (H), latent heat flux (LE), evapotranspiration (ET), crop coefficient (K_c) and crop water productivity (WP_ET) were investigated under two different rice environments, flooded and aerobic soil conditions, using the eddy covariance (EC) technique during 2008-2009 cropping periods. Since we had only one EC system for monitoring two rice environments, we had to move the system from one location to the other every week. In total, we had to gap-fill an average of 50-60% of the missing weekly data as well as those values rejected by the quality control tests in each rice field in all four cropping seasons. Although the EC method provides a direct measurement of LE, which is the energy used for ET, we needed to correct the values of H and LE to close the energy balance using the Bowen ratio closure method before we used LE to estimate ET. On average, the energy balance closure before correction was 0.72 ± 0.06 and it increased to 0.99 ± 0.01 after correction. The G in both flooded and aerobic fields was very low. Likewise, the energy involved in miscellaneous processes such as photosynthesis, respiration and heat storage in the rice canopy was not taken into consideration.Average for four cropping seasons, flooded rice fields had 19% more LE than aerobic fields whereas aerobic rice fields had 45% more H than flooded fields. This resulted in a lower Bowen ratio in flooded fields (0.14 ± 0.03) than in aerobic fields (0.24 ± 0.01). For our study sites, evapotranspiration was primarily controlled by net radiation. The aerobic rice fields had lower growing season ET rates (3.81 ± 0.21 mm d⁻¹) than the flooded rice fields (4.29 ± 0.23 mm d⁻¹), most probably due to the absence of ponded water and lower leaf area index of aerobic rice. Likewise, the crop coefficient, K_c, of aerobic rice was significantly lower than that of flooded rice. For aerobic rice, K_c values were 0.95 ± 0.01 for the vegetative stage, 1.00 ± 0.01 for the reproductive stage, 0.97 ± 0.04 for the ripening stage and 0.88 ± 0.03 for the fallow period, whereas, for flooded rice, K_c values were 1.04 ± 0.04 for the vegetative stage, 1.11 ± 0.05 for the reproductive stage, 1.04 ± 0.05 for the ripening stage and 0.93 ± 0.06 for the fallow period. The average annual ET was 1301 mm for aerobic rice and 1440 mm for flooded rice. This corresponds to about 11% lower total evapotranspiration in aerobic fields than in flooded fields. However, the crop water productivity (WP_ET) of aerobic rice (0.42 ± 0.03 g grain kg⁻¹ water) was significantly lower than that of flooded rice (1.26 ± 0.26 g grain kg⁻¹ water) because the grain yields of aerobic rice were very low since they were subjected to water stress.The results of this investigation showed significant differences in energy balance and evapotranspiration between flooded and aerobic rice ecosystems. Aerobic rice is one of the promising water-saving technologies being developed to lower the water requirements of the rice crop to address the issues of water scarcity. This information should be taken into consideration in evaluating alternative water-saving technologies for environmentally sustainable rice production systems.     

SEBAL for detecting spatial variation of water productivity and scope for improvement in eight irrigated wheat systems

A methodology has been developed to quantify spatial variation of crop yield, evapotranspiration (ET) and water productivity (WP_ET) using the SEBAL algorithm and high and low resolution satellite images. SEBAL-based ET estimates were validated over an irrigated, wheat dominated area in the Yaqui Valley, Mexico and proved to be accurate (8.8% difference for 110 days). Estimated average wheat yields in Yaqui Valley of 5.5 t ha⁻¹ were well within the range of measured yields reported in the literature. Measured wheat yields in 24 farmers’ fields in Sirsa district, India, were 0.4 t ha⁻¹ higher than SEBAL estimated wheat yields. Area average WP_ET in the Yaqui Valley was 1.37 kg m⁻³ and could be considered to be high as compared to other irrigated systems around the world where the same methodology was applied. A higher average WP_ET was found in Egypt's Nile Delta (1.52 kg m⁻³), Kings County (CA), USA (1.44 kg m⁻³) and in Oldambt, The Netherlands (1.39 kg m⁻³). The spatial variability of WP_ET within low productivity systems (CV = 0.33) is higher than in high productivity systems (CV = 0.05) because water supply in the former case is uncertain and farming conditions are sub-optimal. The high CV found in areas with low WP_ET indicates that there is considerable scope for improvement. The average scope for improvement in eight systems was 14%, indicating that 14% ET reduction can be achieved while maintaining the same yield. It is concluded that the proposed methodology is accurate and that better knowledge of the spatial variation of WP_ET provides valuable information for achieving local water conservation practices in irrigated wheat.     

Soil fertility and nutrient uptake by arecanut (Arecacatechu L.) as affected by level and frequency of fertigation in a laterite soil

Changes in soil fertility status were evaluated for 10 years, from 1996 to 2006 to examine the impact of drip fertigation in a laterite soil and to determine the nutrient uptake pattern of arecanut (Areca catechu L.). Four fertigation levels (25%, 50%, 75% and 100% of recommended fertilizer dose, 100:18:117 g N:P:K palm⁻¹ year⁻¹), three frequencies of fertigation (10, 20 and 30 days) and two controls (control 1: drip irrigation without fertilizer application and control 2: drip irrigation with 100% NPK soil application) were studied. The soil pH increased to 6.0 at the end of experiment in 2006 compared to the pre-experimental soil pH of 5.6 in 1996. In 0-25-cm depth interval, the soil organic carbon (SOC) increased significantly from 1.06% in 1999 to 1.84% in 2006, and in 25-50-cm depth interval, it increased from 0.68% to 1.13%. Temporal variation in available P and K content in arecanut root zone was significant due to drip fertigation. Pooled analysis of data, from 2000 to 2005, revealed significant impact of level and frequency of fertigation and their interaction on available P and K content. At 0-25-cm depth interval, increase in fertigation dose from 50% to 100% NPK did not result in significant increase of Bray’s P content, which remained at par ranging from 5.24 to 5.32 mg kg⁻¹. Fertigation every 30 days resulted in significantly higher available P (5.32 mg kg⁻¹) than fertigation every 10 days (4.49 mg kg⁻¹), while it was at par with fertigation every 20 days (5.09 mg kg⁻¹). The K availability at 0-25-cm depth interval was significantly lower at 25% NPK level (114 mg kg⁻¹) than at 75% (139 mg kg⁻¹) and 100% (137 mg kg⁻¹). With respect to fertigation frequency, the 30-day interval resulted in higher available K of 139 mg kg⁻¹ than 20-day (128 mg kg⁻¹) and 10-day intervals (120 mg kg⁻¹). Availability of P and K at 25-50-cm depth interval followed similar trend as that of 0-25-cm depth interval. The total N uptake (g palm⁻¹ year⁻¹) by leaves, nuts and husk varied between 143 in 0% NPK to 198 in 75% NPK fertigation level. Similarly, the total P uptake (g palm⁻¹ year⁻¹) ranged between 15 for the 0% NPK and 25 for the 75% NPK treatment. The total K uptake (g palm⁻¹ year⁻¹) was 62 for the 75% NPK treatment followed by 56 for the 25%, 56 for the 50%, 54 for the 100% and 46 for the 0% NPK treatments. The nutrient uptake pattern and marginal availability of soil P and K highlight the importance of drip fertigation during post-monsoon season to improve and sustain the yield of arecanut in a laterite soil.     

Drip irrigation of tea (Camellia sinensis L.): 1. Yield and crop water productivity responses to irrigation

The effects of drip irrigation on the yield and crop water productivity responses of four tea (Camellia sinensis (L.) O. Kuntze) clones were studied four consecutive years (2003/2004-2006/2007), in a large (9 ha) field experiment comprising of six drip irrigation treatments (labelled: I₁-I₆) and four clones (TRFCA PC81, AHP S15/10, BBK35 and BBT207) planted at a spacing of 1.20 m × 0.60 m at Kibena Tea Limited (KTL), Njombe in the Southern Tanzania in a situation of limited water availability. Each clone × drip irrigation treatment combination was replicated six times in a completely randomized design with 144 net plots each with an area of 72 m². Clone TRFCA PC81 gave the highest yields (range: 5920-6850 kg dried tea ha⁻¹) followed by clones BBT207 (5010-5940 kg dried tea ha⁻¹), AHP S15/10 (4230-5450 kg dried tea ha⁻¹) and BBK35 (3410-4390 kg dried tea ha⁻¹) and drip irrigation treatment I₂ gave the highest yields, ranging from 4954 to 6072 kg dried tea ha⁻¹) compared with those from other treatments (4113-5868 kg dried tea ha⁻¹). Most of these yields exceeded those (4200 kg dried tea ha⁻¹) obtained from overhead sprinkler irrigation system in Mufindi also Southern Tanzania, and Kibena Estate itself. Results showed that drip irrigation of tea not only increased yields but also gave water saving benefits of up to 50% from application of 50% less water to remove the cumulative soil water deficit (treatment I₂), and with labour saving of 85% for irrigation. The yield of dried tea per mm depth of water applied, i.e., “the crop water productivity” for drip irrigation of clones TRFCA PC81, BBT207 and BBK35, in 2003/2004 for instance, were 9.3, 8.5 and 7.1 kg dried tea [ha mm]⁻¹, respectively. The corresponding values in 2004/2005 were 2.7, 4.5 and 2.0 kg dried tea [ha mm]⁻¹ while the yield responses from clone AHP S15/10 were linear decreasing by 1 and 1.6 kg dried tea [ha mm]⁻¹ in 2003/2004 and 2004/2005, respectively. In 2005/2006 the crop water productivity from clones TRFCA PC81, AHP S15/10, BBK35 and BBT207 were 4.5, 0.4, 5.2 and 6.9 kg dried tea [ha mm]⁻¹, respectively with quadratic yield response functions to drip irrigation depth of water application. The results are presented and recommendations and implications made for technology-transfer scaling-up for increased use by large and smallholder tea growers.     

Evapotranspiration and water use of full and deficit irrigated cotton in the Mediterranean environment in northern Syria

Cotton (Gossypium hirsutum L.) is the most important industrial and summer cash crop in Syria and many other countries in the arid areas but there are concerns about future production levels, given the high water requirements and the decline in water availability. Most farmers in Syria aim to maximize yield per unit of land regardless of the quantity of water applied. Water losses can be reduced and water productivity (yield per unit of water consumed) improved by applying deficit irrigation, but this requires a better understanding of crop response to various levels of water stress. This paper presents results from a 3-year study (2004-2006) conducted in northern Syria to quantify cotton yield response to different levels of water and fertilizer. The experiment included four irrigation levels and three levels of nitrogen (N) fertilizer under drip irrigation. The overall mean cotton (lint plus seed, or lintseed) yield was 2502 kg ha⁻¹, ranging from 1520 kg ha⁻¹ under 40% irrigation to 3460 kg ha⁻¹ under 100% irrigation. Mean water productivity (WP_ET) was 0.36 kg lintseed per m³ of crop actual evapotranspiration (ET_c), ranging from 0.32 kg m⁻³ under 40% irrigation to 0.39 kg m⁻³ under the 100% treatment. Results suggest that deficit irrigation does not improve biological water productivity of drip-irrigated cotton. Water and fertilizer levels (especially the former) have significant effects on yield, crop growth and WP_ET. Water, but not N level, has a highly significant effect on crop ET_c. The study provides production functions relating cotton yield to ET_c as well as soil water content at planting. These functions are useful for irrigation optimization and for forecasting the impact of water rationing and drought on regional water budgets and agricultural economies. The WP_ET values obtained in this study compare well with those reported from the southwestern USA, Argentina and other developed cotton producing regions. Most importantly, these WP_ET values are double the current values in Syria, suggesting that improved irrigation water and system management can improve WP_ET, and thus enhance conservation and sustainability in this water-scarce region.     

Irrigation, tillage and mulching effects on soybean yield and water productivity in relation to soil texture

Depleting groundwater resources in Indian Punjab call for diversifying from rice to crops with low evapo-transpiration needs and adopting water-saving technologies. Soybean offers a diversification option in coarse- to medium-textured soils. However, its productivity in these soils is constrained by high soil mechanical resistance and high soil temperature during early part of the growing season. These constraints can be alleviated through irrigation, deep tillage and straw mulching. This 3-years field study examines the individual and combined effects of irrigation, deep tillage, and straw mulching regimes on soybean yield and water productivity (WP) in relation to soil texture. Combinations of two irrigation regimes viz., full irrigation (I_f), and partial irrigation (I_p) in the main plot; two tillage regimes viz., conventional-till (CT)-soil stirring to 0.10 m depth, and deep tillage (DT)-chiseling down to 0.35 m depth followed by CT in the subplot; and two mulch rates viz., 0 (M₀) and 6 t ha⁻¹ (M) in the sub-subplot on two soils differing in available water capacity were evaluated.Seed yield was greater in the sandy loam than in the loamy sand reflecting the effects of available water capacity. Irrigation effects were greater on loamy sand (40%) than on sandy loam (5%) soil. Deep tillage benefits were also more on loamy sand (14%) compared to sandy loam (5%) soil. Yield gains with mulching were comparable on the two soils (19%). An evaluation of interaction effects showed that mulching response was slightly more in I_p (20%) than in I_f regimes (17%) in the sandy loam; while in the loamy sand, mulching gains were comparable (18-19%) in both irrigation regimes. Benefits of deep tillage in the loamy sand soil were more in I_p (20%) than in I_f regimes (17%). Deep tillage and straw mulching enhanced WP (ratio of seed yield/water use) from 1.39 to 1.97 kg ha⁻¹ mm⁻¹ in I_p regime, and from 1.87 to 2.33 kg ha⁻¹ mm⁻¹ in I_f regime in the loamy sand soil. These effects on WP were less in the sandy loam soil with greater available water capacity. Yield and WP gains are ascribed to deeper and denser rooting due to moderation of soil temperature and water conservation with straw mulching and tillage-induced reduction in soil mechanical resistance. Root mass in CTM₀, CTM, DTM₀ and DTM was 2.79, 5.88, 5.34 and 5.58 mg cm⁻² at pod-filling in the loamy sand soil. Comparable yield responses to deep tillage or mulching in the loamy sand soil suggest that either of the options, depending on their cost and availability considerations, can be employed for improving soybean yield and water productivity.     

Changes in evapotranspiration over irrigated winter wheat and maize in North China Plain over three decades

Evapotranspiration (ET) is an important component of the water cycle at field, regional and global scales. This study used measured data from a 30-year irrigation experiment (1979-2009) in the North China Plain (NCP) on winter wheat (Triticum aestivum L.) and summer maize (Zea mays L.) to analyze the impacts of climatic factors and crop yield on ET. The results showed that grass reference evapotranspiration (ET_o, calculated by FAO Penmen-Monteith method) was relatively constant from 1979 to 2009. However, the actual seasonal ET of winter wheat and maize under well-watered condition gradually increased from the 1980s to the 2000s. The mean seasonal ET was 401.4 mm, 417.3 mm and 458.6 mm for winter wheat, and 375.7 mm, 381.1 mm and 396.2 mm for maize in 1980s, 1990s and 2000s, respectively. The crop coefficient (K_c) was not constant and changed with the yield of the crops. The seasonal average K_c of winter wheat was 0.75 in the 1980s, 0.81 in the 1990s and 0.85 in the 2000s, and the corresponding average grain yield (GY) was 4790 kg ha⁻¹, 5501 kg ha⁻¹ and 6685 kg ha⁻¹. The average K_c of maize was 0.88 in the 1980s, 0.88 in the 1990s and 0.94 in the 2000s, with a GY of 5054 kg ha⁻¹, 7041 kg ha⁻¹ and 7874 kg ha⁻¹, respectively, for the three decades. The increase in ET was not in proportion to the increase in GY, resulting improved water use efficiency (WUE). The increase in ET was possibly related to the increase in leaf stomatal conductance with renewing in cultivars. The less increase in water use with more increase in grain production could be partly attributed to the significant increase in harvest index. The results showed that with new cultivars and improved management practices it was possible to further increase grain production without much increase in water use.     

Tuber yield, water and fertilizer productivity in early potato as affected by a combination of irrigation and fertilization

Excessive amounts of irrigation water and fertilizers are often utilized for early potato cultivation in the Mediterranean basin. Given that water is expensive and limited in the semi-arid areas and that fertilizers above a threshold level often prove inefficacious for production purposes but still risk nitrate and phosphorous pollution of groundwater, it is crucial to provide an adequate irrigation and fertilization management. With the aim of achieving an appropriate combination of irrigation water and nutrient application in cultivation management of a potato crop in a Mediterranean environment, a 2-year experiment was conducted in Sicily (South Italy). The combined effects of 3 levels of irrigation (irrigation only at plant emergence, 50% and 100% of the maximum evapotranspiration - ETM) and 3 levels of mineral fertilization (low: 50, 25 and 75 kg ha⁻¹, medium: 100, 50 and 150 kg ha⁻¹ and high: 300, 100 and 450 kg ha⁻¹ of N, P₂O₅ and K₂O) were studied on the tuber yield and yield components, on both water irrigation and fertilizer productivity and on the plant source/sink (canopy/tubers dry weight) ratio. The results show a marked interaction between level of irrigation and level of fertilization on tuber yield, on Irrigation Water Productivity and on fertilizer productivity of the potato crop. We found that the treatments based on 50% ETM and a medium level of fertilization represent a valid compromise in early potato cultivation management. Compared to the high combination levels of irrigation and fertilization, this treatment entails a negligible reduction in tuber yield to save 90 mm ha⁻¹ year⁻¹ of irrigation water and 200, 50 and 300 kg ha⁻¹ year⁻¹ of N, P₂O₅ and K₂O, respectively, with notable economic savings for farmers compared to the spendings that are usually made.     

Yield and quality of melon grown under different irrigation and nitrogen rates

During 2 years, a melon crop (Cucumis melo L. cv. Sancho) was grown under field conditions to investigate the effects of different nitrogen (N) and irrigation (I) levels on fruit yield, fruit quality, irrigation water use efficiency (IWUE) and nitrogen applied efficiency (NAE). The statistical design was a split-plot with four replications, where irrigation was the main factor of variation and N was the secondary factor. In 2005, irrigation treatments consisted of applying daily a moderate water stress equivalent to 75% of ETc (crop evapotranspiration), a 100% ETc control and an excess irrigation of 125% ETc (designated as I₇₅, I₁₀₀ and I₁₂₅), while the N treatments were 30, 85, 112 and 139 kg N ha⁻¹ (designated as N₃₀, N₈₅, N₁₁₂ and N₁₃₉). In 2006, both the irrigation and N treatments applied were: 60, 100 and 140% ETc (I₆₀, I₁₀₀ and I₁₄₀) and 93, 243 and 393 kg N ha⁻¹ (N₉₃, N₂₄₃ and N₃₉₃). Moderate water stress did not reduce melon yield and high IWUE was obtained. Under severe deficit irrigation, the yield was reduced by 22% mainly due to decrease fruit weight. The relative yield (yield/maximum yield) was higher than 95% when the irrigation depth applied was in the range of 87-136% ETc. In 2006, the interaction between irrigation and N was significant for yield, fruit weight and IWUE. The best yield, 41.3 Mg ha⁻¹, was obtained with 100% ETc at N₉₃. The flesh firmness and the placenta and seeds weight increased when the irrigation level was reduced by 60% ETc. The highest NAE was obtained with quantities of water close to 100% ETc and increased as the N level was reduced. The highest IWUE was obtained with applications close to 90 kg N ha⁻¹. The I₂₄₃ and I₃₉₃ treatments produced inferior fruits due to higher skin ratios and lower flesh ratios. These results suggest that it is possible to apply moderate deficit irrigation, around 90% ETc, and reduce nitrogen input to 90 kg ha⁻¹ without lessening quality and yields.     

Irrigation strategies to improve the water use efficiency of wheat-maize double cropping systems in North China Plain

Water is the most important limiting factor of wheat (Triticum aestivum L.) and maize (Zea mays L.) double cropping systems in the North China Plain (NCP). A two-year experiment with four irrigation levels based on crop growth stages was used to calibrate and validate RZWQM2, a hybrid model that combines the Root Zone Water Quality Model (RZWQM) and DSSAT4.0. The calibrated model was then used to investigate various irrigation strategies for high yield and water use efficiency (WUE) using weather data from 1961 to 1999. The model simulated soil moisture, crop yield, above-ground biomass and WUE in responses to irrigation schedules well, with root mean square errors (RMSEs) of 0.029 cm³ cm⁻³, 0.59 Mg ha⁻¹, 2.05 Mg ha⁻¹, and 0.19 kg m⁻³, respectively, for wheat; and 0.027 cm³ cm⁻³, 0.71 Mg ha⁻¹, 1.51 Mg ha⁻¹ and 0.35 kg m⁻³, respectively, for maize. WUE increased with the amount of irrigation applied during the dry growing season of 2001-2002, but was less sensitive to irrigation during the wet season of 2002-2003. Long-term simulation using weather data from 1961 to 1999 showed that initial soil water at planting was adequate (at 82% of crop available water) for wheat establishment due to the high rainfall during the previous maize season. Preseason irrigation for wheat commonly practiced by local farmers should be postponed to the most sensitive growth stage (stem extension) for higher yield and WUE in the area. Preseason irrigation for maize is needed in 40% of the years. With limited irrigation available (100, 150, 200, or 250 mm per year), 80% of the water allocated to the critical wheat growth stages and 20% applied at maize planting achieved the highest WUE and the least water drainage overall for the two crops.     

Response of vanilla (Vanilla planifolia A.) intercropped in arecanut to irrigation and nutrition in humid tropics of India

A 5-year field trial to assess the impact of microsprinkler irrigation and nutrition on vanilla grown as intercrop in arecanut plantation was conducted on a laterite soil. Pooled analysis indicated that microsprinkler irrigation at 1.0 Epan resulted in significantly higher green bean yield (842 kg ha⁻¹) than 0.75 Epan (579 kg ha⁻¹). Organic manure application in the form of vermicompost (720 kg ha⁻¹) and FYM (768 kg ha⁻¹) and recommended NPK (718 kg ha⁻¹) produced green bean yield at par with recycling of gliricidia prunings (625 kg ha⁻¹). Irrigation at 1.0 Epan proved superior by registering maximum benefit:cost (B:C) ratio of 2.25 compared to 1.62 at 0.75 Epan. The highest B:C ratio was obtained with recommended NPK (2.27) followed by recycling of gliricidia prunings (2.10), vermicompost (1.87), vermicompost + arecanut husk mulching (1.80) and FYM (1.64). The soil pH increased by 0.4 units in 2008 compared with the pre-experimental soil pH of 5.6 in 2004. Nutrition alone and in combination with irrigation had significant impact on soil pH. Organic manure application increased the soil pH (6.1-6.2) significantly over recommended NPK (5.6) at the end of experiment in 2008. Significant variation in soil organic carbon (SOC) was noticed due to different nutrition treatments. Application of vermicompost and FYM significantly increased the SOC content by 38-54% in 2008 over initial levels in 2004. Bray's P availability was influenced by nutrition and its interaction with irrigation. Application of FYM continuously for 4 years has resulted in significant increase in Bray's P content (41.3 mg kg⁻¹) compared to other nutrition treatments (9.4-17.2 mg kg⁻¹). Irrigation equivalent to 0.75 Epan (223 mg kg⁻¹) increased the K availability significantly over 1.0 Epan (172 mg kg⁻¹). The K availability was significantly higher in recommended NPK (416 mg kg⁻¹) than in other organic treatments (98-223 mg kg⁻¹) at 0-30 cm soil depth. Overall, vanilla responded well to irrigation and nutrition in arecanut-based cropping system with a better economic output and improved soil fertility.     

Comparison of drip and sprinkler irrigation strategies on sunflower seed and oil yield and quality under Mediterranean climatic conditions

This study compares the effects of different irrigation regimes on seed yield and oil yield quality and water productivity of sprinkler and drip irrigated sunflower (Helianthus annus L.) on silty-clay-loam soils in 2006 and 2007 in the Mediterranean region of Turkey. In sprinkler irrigation a line-source system was used in order to create gradually varying irrigation levels. Irrigation regimes consisted of full irrigation (I₁) and three deficit irrigation treatments (I₂, I₃ and I₄), and rain-fed treatment (I₅). In the drip system, irrigation regimes included full irrigation (FI-100), three deficit irrigation treatments (DI-25, DI-50, DI-75), partial root zone drying (PRD-50) and rain-fed treatment (RF). Irrigations were scheduled at weekly intervals both in sprinkler and drip irrigation, based on soil water depletion within a 0.90 m root zone in FI-100 and I₁ plots. Irrigation treatments influenced significantly (P < 0.01) sunflower seed and oil yields, and oil quality both with sprinkler and drip systems. Seed yields decreased with increasing water stress levels under drip and sprinkler irrigation in both experimental years. Seed yield response to irrigation varied considerably due to differences in soil water contents and spring rainfall distribution in the experimental years. Although PRD-50 received about 36% less irrigation water as compared to FI-100, sunflower yield was reduced by an average of 15%. PRD-50 produced greater seed and oil yields than DI-50 in the drip irrigation system. Yield reduction was mainly due to less number of seeds per head and lower seed mass. Soil water deficits significantly reduced crop evapotranspiration (ET), which mainly depends on irrigation amounts. Significant linear relationships (R² = 0.96) between ET and oil yield (Y) were obtained in each season. The seed yield response factors (ky_seed) were 1.24 and 0.86 for the sprinkler and 1.19 and 1.06 for the drip system in 2006 and 2007, respectively. The oil yield response factor (ky_oil) for sunflower was found to be 1.08 and 1.49 for both growing seasons for the sprinkler and 1.36 and 1.25 for the drip systems, respectively. Oil content decreased with decreasing irrigation amount. Consistently greater values of oil content were obtained from the full irrigation treatment plots. The saturated (palmitic and stearic acid) and unsaturated (oleic and linoleic acid) fatty acid contents were significantly affected by water stress. Water stress caused an increase in oleic acid with a decrease in linoleic acid contents. The palmitic and stearic acid concentrations decreased under drought conditions. Water productivity (WP) values were significantly affected by irrigation amounts and ranged from 0.40 to 0.71 kg m⁻³ in 2006, and from 0.69 to 0.91 kg m⁻³ in 2007. The PRD-50 treatment resulted in the greatest WP (1.0 kg m⁻³) and irrigation water productivity (IWP) (1.4 kg m⁻³) in both growing seasons. The results revealed that under water scarcity situation, PRD-50 in drip and I₂ in sprinkler system provide acceptable irrigation strategies to increase sunflower yield and quality.     

Evaluation of the VegSyst model with muskmelon to simulate crop growth, nitrogen uptake and evapotranspiration

Like many intensive vegetable production systems, the greenhouse-based system on the south-eastern (SE) Mediterranean coast of Spain is associated with considerable NO₃⁻ contamination of groundwater. Drip irrigation and sophisticated fertigation systems provide the technical capacity for precise nutrient and irrigation management of soil-grown crops which would reduce NO₃⁻ leaching loss. The VegSyst crop simulation model was developed to simulate daily crop biomass production, N uptake and crop evapotranspiration (ET_c). VegSyst is driven by thermal time and consequently is adaptable to different planting dates, different greenhouse cooling practices and differences in greenhouse design. It will be subsequently incorporated into a practical on-farm decision support system to enable growers to more effectively use the advanced technical capacity of this horticultural system for optimal N and irrigation management.VegSyst was calibrated and validated for muskmelon grown in Mediterranean plastic greenhouse in SE Spain using data of four melon crops, two grown in 2005 and two in 2006 using two management strategies of water and N management in each year. VegSyst very accurately simulated crop biomass production and accurately simulated crop N uptake over time. Model performance in simulating dry matter production (DMP) over time was better using a double radiation use efficiency (RUE) approach (5.0 and 3.2 g MJ⁻¹ PAR for vegetative and reproductive growth phases) compared to a single RUE approach (4.3 g MJ⁻¹ PAR). The simulation of ET_c over time, was very accurate in the two 2006 muskmelon crops and somewhat less so in the two 2005 crops. The error in the simulated final values, expressed as a percentage of final measured values was −1 to 6% for DMP, 2-11% for crop N uptake, and −11 to 6% for ET_c. VegSyst provided effective simulation of DMP, N uptake and ET_c for crops with different planting dates. This model can be readily adapted to other crops.     

Chickpea water use efficiency in relation to cropping system, cultivar, soil nitrogen and Rhizobial inoculation in semiarid environments

Crops grown in semiarid rainfed conditions are prone to water stress which could be alleviated by improving cultural practices. This study determined the effect of cropping system, cultivar, soil nitrogen status and Rhizobium inoculation (Rz) on water use and water use efficiency (WUE) of chickpea (Cicer arietinum L.) in semiarid environments. The cultivars Amit, CDC Anna, CDC Frontier, and CDC Xena were grown in no-till barley, no-till wheat, and tilled-fallow systems and under various rates of N fertilizer (0, 28, 56, 84, and 112 kg N ha⁻¹) coupled with or without Rz. The study was conducted at Swift Current and Shaunavon, Saskatchewan, from 2004 to 2006. On average, chickpea used about 10 mm of water from the top 0-15 cm soil depth. In the tilled-fallow system, chickpea extracted 20% more water in the 15-30 cm depth, 70% more in the 30-60 cm depth, and 156% more in the 60-120 cm depth than when it was grown in the no-till systems. CDC Xena had WUE of 5.3 kg ha⁻¹ mm⁻¹ or 20% less than the average WUE (6.6 kg ha⁻¹ mm⁻¹) of the three other cultivars, even though these cultivars used the same amounts of water. Water use efficiency increased from 4.7 to 6.8 kg ha⁻¹ mm⁻¹ as N fertilizer rate was increased from 0 to 112 kg N ha⁻¹ when chickpea was grown in the no-till barley or wheat systems, but chickpea grown in the tilled-fallow system did not respond to changes in the fertilizer N rates averaging WUE of 6.5 kg ha⁻¹ mm⁻¹. In the absence of N fertilizer, the application of Rz increased WUE by 33% for chickpea grown in the no-till barley system, 30% in the no-till wheat system, and 9% in the tilled-fallow system. Chickpea inoculated with Rhizobium achieved a WUE value similar to the crop fertilized at 84 kg N ha⁻¹. Without the use of Rz, chickpea increased WUE in a linear fashion with increasing fertilizer N rates from 0 to 84 kg N ha⁻¹. Cropping system, cultivar, and inoculation all had greater impact on WUE than on the amount of water extracted by the crop from the soil. The improvement of cultural practices to promote general plant health along with the development of cultivars with improved crop yields will be keys for improving water use efficiency of chickpea in semiarid environments.     

In-season wheat root growth and soil water extraction in the Mediterranean environment of northern Syria

Wheat is the most important cereal crop in the semi-arid eastern Mediterranean region that includes northern Syria. Knowledge of wheat root depth and the vertical distribution during the winter growing season is needed for sound scheduling of irrigation and efficient use of water. This article reports evaluation of root development for three winter-grown bread (Triticum aestivum L.) and durum (Triticum turgidum L.) wheat under four soil water regimes (rainfed and full irrigation with two intermediate levels of 33 and 66% of full irrigation). Roots were sampled by soil coring to a depth of 0.75 m at four occasions during 2005-2006 growing season. Two distinct phases of root development were identified, a rapid downward penetration from emergence to end tillering phase, followed by a substantial root mass growth along the profile from tillering to mid-stem-elongation phase. Roots were detected as deep as 0.75 m during the initial rapid penetration, yet only 29% of the total seasonal root mass was developed. This downward penetration rate averaged 7 mm d⁻¹ and produced 10.8 kg ha⁻¹ d⁻¹ of root dry-biomass. The bulging of root mass from tillering to mid-stem-elongation coincided with vigorous shoot growth, doubling root dry-biomass at a rate of 52 kg ha⁻¹ d⁻¹, compared to the seasonal root growth rate of 18.3 kg ha⁻¹ d⁻¹. A second-degree equation described the total root dry-biomass as a function of days after emergence (r² = 0.85), whereas a simpler equation predicted it as a function of cumulative growing degree days (r² = 0.85). The final grain yield was a strong function of irrigation regimes, varying from 3.0 to 6.5 t ha⁻¹, but showed no correlation with root biomass which remained similar as soil water regimes changed. This observation must be viewed with care as it lacks statistical evidence. Results showed 90% of root mass at first irrigation (15 April) confined in the top 0.60-0.75 m soil in bread wheat. Presence of shallow restricting soil layers limited root depth of durum wheat to 0.45 m, yet total seasonal root mass and grain yield were comparable with non-restricted bread wheat. Most root growth occurred during the cool rainy season and prior to the late irrigation season. The root sampling is short of rigorous, but results complement the limited field data in literature collectively suggesting that irrigation following the rainy season may best be scheduled assuming a well developed root zone as deep as the effective soil depth within the top meter of soil.     

Effects of deficit irrigation on the yield and yield components of drip irrigated cotton in a mediterranean environment

A field study on cotton (Gossypium hirsutum L., cv.) was carried out from 2005 to 2008 in the Çukurova Region, Eastern Mediterranean, Turkey. Treatments were designated as I₁₀₀ full irrigation; DI₇₀, DI₅₀ and DI₀₀ which received 70, 50, and 0% of the irrigation water amount applied in the I₁₀₀ treatment. The irrigation water amount to be applied to the plots was calculated using cumulative pan evaporation that occurred during the irrigation intervals. The effect of water deficit or water stress on crop yield and some plant growth parameters such as yield response, water use efficiencies, dry matter yield (DM), leaf area index (LAI) as well as on lint quality components was evaluated. The average seasonal evapotranspiration ranged from 287 ± 15 (DI₀₀) to 584 ± 80 mm (I₁₀₀). Deficit irrigation significantly affected crop yield and all yield components considered in this study. The average seed cotton yield varied from 1369 ± 197 (DI₀₀) to 3397 ± 508 kg ha⁻¹ (I₁₀₀). The average water use efficiency (WUE_ET) ranged from 6.0 ± 1.6 (I₁₀₀) to 4.8 ± 0.9 kg ha⁻¹ mm⁻¹ (DI₀₀), while average irrigation water use efficiency (WUE_I) was between 9.4 ± 3.0 (I₁₀₀) and 14.4 ± 4.8 kg ha⁻¹ mm⁻¹ (DI₅₀). Deficit irrigation increased the harvest index (HI) values from 0.26 ± 0.054 (I₁₀₀) to 0.32 ± 0.052 kg kg⁻¹ (DI₅₀). Yield response factor (Ky) was determined to be 0.98 based on four-year average. Leaf area index (LAI) and dry matter yields (DM) increased with increasing water use. This study demonstrated that the full irrigated treatment (I₁₀₀) should be used for semiarid conditions with no water shortage. However, DI₇₀ treatment needs to be considered as a viable alternative for the development of reduced irrigation strategies in semiarid regions where irrigation water supplies are limited.     

Differences in water use efficiency among annual forages used by the dairy industry under optimum and deficit irrigation

The increasing cost and scarcity of water for irrigation is placing pressure on Australian dairy farmers to utilize water more efficiently, and as result, water use efficiency (WUE) of forages is becoming an important criterion for sustainable dairy production. This study was conducted to identify more water use efficient forage species than the dominant dairy forage, perennial ryegrass (Lolium perenne L.). Seventeen annual forage species were investigated under optimum irrigation (I1) and two deficit irrigation treatments (nominally 66 and 33% of irrigation water applied to the optimal level), over 3 years at Camden, NSW, on a brown Dermsol in a warm temperate climate. Forages with the highest yield generally had the highest WUE_t (total yield/evapotranspiration). Under optimal irrigation, there was a three-fold difference in mean annual WUE_t between forages, with maize (Zea mays L.) having the highest (42.9 kg ha⁻¹ mm⁻¹) and cowpea (Vigna unguiculata (L.) Walp.) the lowest (13.5 kg ha⁻¹ mm⁻¹), with 11 of the forage species having a greater WUE_t than perennial ryegrass. The ‘harvested’ forages maize, wheat, triticale (Triticosecale rimpaui Wittm.) and maple pea (Pisum sativium L.) generally had higher mean WUE_t (26.7-42.9 kg ha⁻¹ mm⁻¹) than the remaining forages which were defoliated multiple times to simulate grazing (13.5-30.1 kg ha⁻¹ mm⁻¹). The reduction in annual WUE_t in response to deficit irrigation was greatest for the warm season forages with up to 30% reduction for maize, while most of the cool season annuals were not significantly affected by deficit irrigation at the levels imposed. In order to maximize WUE_t of any forage, it is necessary to maximize yield, as there is a strong positive relationship between yield and WUE_t. However, while WUE_t is an important criterion for choosing dairy forages, it is only one factor in a complex system. Choice of forages must be considered on a whole farm basis and include consideration of yield, nutritive value, cost of production and risk.