Residual strain analysis with digital image correlation method for subsurface damage evaluation of hinoki (<Emphasis Type="Italic">Chamaecyparis obtusa</Emphasis>) finished by slow-speed orthogonal cutting

A digital image correlation (DIC) method was applied to measure strain which arose and remained beneath the finished surface in slow-speed orthogonal cutting of hinoki (Chamaecyparis obtusa), to evaluate the damage in the subsurface cell layers. While the quarter-sawn surface was cut parallel to the grain, the side surface, flat-sawn surface, was captured by a high-speed camera. The images were analyzed to calculate strain in a region of 0.67 × 0.22 mm allocated beneath the finished surface. Almost no strain normal to the cutting direction was detected for the depth of cut and cutting angles, 0.05 mm and smaller than 60°, respectively. For the depths of cut and cutting angles, larger than 0.1 mm and smaller than 60°, respectively, the fore-split induced tensile strain normal to the cutting direction, although it hardly remained after the cutting. The compression strain normal to the cutting direction clearly remained for the cutting angles larger than 70°, regardless of the depths of cut employed in this study. The subsurface damage assumed from the residual strain distribution corresponded to the appearance of the subsurface layer in the X-ray computed tomography (CT) images. It was also revealed, and the DIC program could not always measure excessively large strain correctly.     

Physiological effects of touching hinoki cypress (<Emphasis Type="Italic">Chamaecyparis obtusa</Emphasis>)

This study aimed to clarify the physiological effects of touching hinoki cypress (hereinafter called “hinoki”) (Chamaecyparis obtusa) wood with the palm of the right hand on brain activity and autonomic nervous activity. Twenty-two female university students (mean age 21.1?±?0.2 years) participated in the study. As an indicator of brain activity, oxyhemoglobin (oxy-Hb) concentrations were measured in the left/right prefrontal cortex using near-infrared time-resolved spectroscopy. Heart rate variability (HRV) was used as an indicator of autonomic nervous activity. The high-frequency (HF) component of HRV, which reflected parasympathetic nervous activity, and the low-frequency (LF)/HF ratio, which reflected sympathetic nervous activity, were measured. Plate (300?×?300 mm) of uncoated hinoki was used as tactile stimulation. Marble was used as a control material. After sitting at rest with their eyes closed, the participants touched the materials for 90 s with their eyes still closed. The results showed that tactile stimulation with hinoki significantly decreased oxy-Hb concentration in the left prefrontal cortex and increased ln(HF) reflected parasympathetic nervous activity compared with marble. In conclusion, our study showed that touching hinoki wood with the palm calms prefrontal cortex activity and increases parasympathetic nervous activity, thereby inducing physiological relaxation.     

Structural unit of xylans from sugi (<Emphasis Type="Italic">Cryptomeria japonica</Emphasis>) and hinoki (<Emphasis Type="Italic">Chamaecyparis obtusa</Emphasis>)

Arabinoglucuronoxylans (AGXs) isolated from the holocellulose of sugi (Cryptomeria japonica) and hinoki (Chamaecyparis obtusa) contained one 4-O-methyl-d-glucopyranosyluronic acid (4-O-Me-d-GlcAp) residue per 6.2 d-xylopyranose (d-Xylp) residues and one 4-O-Me-d-GlcAp residue per 3.8 d-Xylp residues. These AGXs were subjected to partial acid hydrolysis. Analyses by size exclusion chromatography and electrospray-ionization mass spectroscopy of the neutral sugar fractions in the hydrolysates showed the presence of xylooligosaccharides having a degree of polymerization of 2-8 in addition to d-Xyl, suggesting that the AGXs from sugi and hinoki contained unsubstituted chains consisting of at least eight d-Xyl residues. The acidic sugars in the hydrolysates were separated into two series of aldouronic acids composed of 4-O-Me-d-GlcAp and d-Xylp by ion-exchange chromatography. The first series included aldouronic acids from aldobiouronic acid (4-O-Me-d-GlcAp-Xyl) to aldopentaouronic acids (4-O-Me-d-GlcAp-Xyl₄). The second series were aldouronic acids composed of two 4-O-Me-d-GlcAp residues and 2-4 d-Xyl residues. In these acidic sugars, the uronic acid side chains were located on two contiguous d-Xyl residues. These facts indicated that AGXs from sugi and hinoki had a structural unit containing two 4-O-Me-d-GlcAp residues on two contiguous d-Xyl residues as well as AGXs from spruce and larch.     

Estimation of stand attributes in <Emphasis Type="Italic">Cryptomeria japonica</Emphasis> and <Emphasis Type="Italic">Chamaecyparis obtusa</Emphasis> stands using QuickBird panchromatic data

This study aims to estimate stand density and stand volume in Cryptomeria japonica and Chamaecyparis obtusa stands from high-resolution satellite data and verify the reliability and uncertainty of the data. Sixty circular sample plots of 0.04 ha each were established. Their stand densities were estimated from the number of tree crowns derived from high-resolution satellite data using the watershed method. Stand densities derived from field surveys in the sample plots were compared with those obtained from high-resolution satellite data by stand age class. As a result, there was a positive correlation between them for sample plots of 41 years of age and over (R = 0.82); however, there was no correlation between them for sample plots of 40 years and under. Individual diameters at breast height (DBH) were estimated from crown areas obtained from high-resolution satellite data for the two species. Using the estimated DBH, individual tree heights were predicted from the height–diameter curves. Stand volumes were estimated from the sum of individual volumes, which were derived from volume formulas having two variables, i.e., DBH and height. Stand volumes derived from the field survey were compared with those obtained from high-resolution satellite data. The correlation coefficient between them for stands of 41 years of age and over was 0.78.     

Relationship between crack propagation and the stress intensity factor in cutting parallel to the grain of hinoki (<Emphasis Type="Italic">Chamaecyparis obtusa</Emphasis>)

The method of digital image correlation (DIC) was applied to the digital image of orthogonal cutting parallel to the grain of hinoki, and the strain distribution near the cutting edge was evaluated. The wood fracture associated with chip generation was considered as mode I fracture, and the stress intensity factor K_I for fracture mode I was calculated from the strain distribution according to the theory of linear elastic fracture mechanics for the anisotropic material. The calculated K_I increased prior to crack propagation and decreased just after the crack propagation. The change in K_I before and after crack propagation, ΔK_I, decreased in accordance with the crack propagation length, although the variance in ΔK_I should depend on the relationships between the resolution of DIC method and the dimensions of cellular structure. The calculated K_I in this study was almost on the same order as reported in the literatures. It was also revealed, for the case of chip generation Type 0 or I, the stress intensity factor for fracture mode II could be negligible due to the higher longitudinal elastic properties of wood in the tool feed direction than the one radial ones, and the mode I fracture was dominant.     

Effect of grain direction on transmittance of 100-GHz millimeter wave for hinoki (<Emphasis Type="Italic">Chamaecyparis obtusa</Emphasis>)

The attenuation coefficients of 100-GHz millimeter waves polarized linearly were measured for cross-cut, quarter-sawn, and flat-sawn boards of hinoki (Chamaecyparis obtusa) that were 0.2–2.0 cm thick. This was done to examine the applicability of free-wave propagation theory for applying electromagnetic waves to wood. It was found that the transmittance of a millimeter wave through the specimen boards was lower when the fiber direction of a board was parallel to the direction of the electric field of the incident wave than when the fiber direction was perpendicular to the electric field, and there was little difference in the transmittance between the tangential and radial directions for the former case. These findings can be quantitatively explained by using propagation theory and the dielectric properties of wood.     

Aboveground biomass equations for individual trees of <Emphasis Type="Italic">Cryptomeria japonica</Emphasis>, <Emphasis Type="Italic">Chamaecyparis obtusa</Emphasis> and <Emphasis Type="Italic">Larix kaempferi</Emphasis> in Japan

Generic equations are proposed for stem, branch and foliage biomass of individual trees in even-aged pure stands of Cryptomeria japonica, Chamaecyparis obtusa and Larix kaempferi. Biomass data was collected from a total of 1,016 individual trees from 247 stands throughout Japan, and five regression models were assessed by root mean square error, mean bias, fit index (FI), and AIC. The results show that a power equation using diameter at breast height (dbh) and height is the most suitable for all species and components. This equation is more accurate than the familiar power equation that uses ‘dbh² height’, and it expresses the greater volume of branch and foliage mass of trees with a lower height/diameter ratio. A power equation using dbh is more reasonable for models with dbh as the only independent variable and more accurate than a power equation using ‘dbh² height’ for estimating branch and foliage mass. Estimating error for branch and foliage mass is larger than that for stem mass, but the entire aboveground biomass can be estimated with an error of less than 19%, except in the case of small trees with dbh less than 10 cm.     

Fine root biomass and morphology of <Emphasis Type="Italic">Pinus densiflora</Emphasis> under competitive stress by <Emphasis Type="Italic">Chamaecyparis obtusa</Emphasis>

The fine root (diameter ≤2.0 mm) biomass and morphology of Japanese red pines (Pinus densiflora) grown under different aboveground conditions (i.e., high and low competitive environments) were examined in a pine–cypress mixed forest. All P. densiflora subject trees were about 40 years old, and the aboveground condition (i.e., size) of red pines appeared to be influenced by the surrounding Japanese cypress (Chamaecyparis obtusa). Smaller P. densiflora exhibited lower fine root biomasses, shorter root lengths, and lower root tip densities, but longer specific root lengths and higher specific root tip densities relative to larger pines. These results suggest that P. densiflora may adjust the morphological traits of fine roots to the different conditions in biomass allocation to fine roots of individuals with different aboveground growth.     

Ring characteristics and screw withdrawal resistance of naturally regenerated <Emphasis Type="Italic">Chamaecyparis obtusa</Emphasis> var. <Emphasis Type="Italic">formosana</Emphasis> trees

The ring characteristics and screw withdrawal resistance (SWR) of naturally regenerated Taiwan yellow cypress (Chamaecyparis obtusa var. formosana) trees were explored. Significant differences in average ring width (RW), earlywood width, latewood width, ring density (RD), earlywood density (ED), latewood density (LD), highest density (D_max), lowest density (D_min), latewood percentage (LWP), and SWR were observed between trees, rings (SWR excluded), and tree height positions. The RW components in the radial direction increased from the pith outward to about the 3rd to 5th ring and then decreased to about the 25th ring; it was almost constantly sustained toward the bark side. The RD in the radial direction slowly decreased from the pith outward to the bark side. Average ring width and ring density were significantly affected by the various tree growth rates, radial ring numbers, and tree height positions. ED, LD, D_max, D_min, and LWP were the most important factors determining the overall RD. RW did not correlate with tree RD. SWR is correlated with ED, RD, D_min, LWP, and intra-ring density variation (IDV). Thus, the SWR can be used to predict wood density and in nondestructive evaluation of a living tree.     

Early growth of hinoki (<Emphasis Type="Italic">Chamaecyparis obtusa</Emphasis>) trees under different topography and edge aspects at a strip-clearcut site in Kyushu,Southern Japan

The positive and negative effects of the residual stand edge at a strip-clearcut site were examined on the initial growth of hinoki (Chamaecyparis obtusa) planted in areas with diverse topography. On the south edge, the gap light index was lower than on the north edge and strip center; however, the vapor pressure deficit was also lower than on the north edge and strip center, which resulted in lower physiological stress of hinoki on the south edge. Tree size on the south edge did not exceed that on the north edge and strip center. These results indicated that low light conditions due to residual trees negatively affected growth on the south edge even under the positive effect of microclimate alleviation. In valley, tree size in the second year after planting was smaller than on ridge and slope; however, tree growth during the following 2 years was higher in valley. Surface soil in valley was thinner with rockier substrates than on ridge and slope; that is, soil sedimentation type and substrates influenced the initial growth of hinoki with undeveloped roots, and after that, topography started to influence growth, probably because hinoki roots penetrated into deeper soil, which is influenced by the water gathering capacity of the valley. The initial growth of hinoki at the strip-clearcut site was predominantly affected by light rather than microclimate alleviation. This alleviation is expected to disappear when hinoki trees planted in the strip center grow enough to give additional shade to slow-growing edge hinoki.     

Delignification of cell walls of <Emphasis Type="Italic">Chamaecyparis obtusa</Emphasis> during alkaline nitrobenzene oxidation

To clarify the behavior of whole lignins in wood cell walls during alkaline nitrobenzene oxidation, the delignification process from cell walls in normal and compression woods of Chamaecyparis obtusa Endl. (Cupressaceae) was observed using ultraviolet and transmission electron microscopies. The lignin content conspicuously decreased to around 10% after 35min in normal wood. The lignin content in compression wood finally leveled off at aroumd 10% after 50min. In gel filtration of oxidation products in ethyl acetate, a high molecular weight fraction was prominent in extracts from the early stage of the reaction. As the oxidation progressed, the high molecular weight fraction became less prominent in both normal and compression wood. Changes in the weights of cell wall residues during reaction indicated that approximately half of the components other than lignin were also removed from the cell walls. This shows that the majority of lignin with relatively high molecular weight is removed from the cell walls together with polysaccharides in the early stage of the reaction and that further oxidative degradation occurs in solution in later stages. Only a small amount of the lignin with low molecular weight could be analyzed by gas chromatography.Parts of this report were presented at the 47th (Kochi, April 1997) and 48th (Shizuoka, April 1998) Annual Meetings of the Japan Wood Research Society, and at the Lignin Symposium, Sapporo, October 1997     

Early establishment of broadleaved trees after logging of <Emphasis Type="Italic">Cryptomeria japonica</Emphasis> and <Emphasis Type="Italic">Chamaecyparis obtusa</Emphasis> plantations with different understory treatments

We studied the effects of the amount of advanced regeneration before logging and different understory treatments on forest recovery, particularly the establishment of lucidophyllous (evergreen broadleaved) species, following the logging of conifer plantation with a focus on the sprouting ability. The establishment of lucidophyllous tree and shrub species originating from advanced regeneration was closely related to the total amount of these elements in the advanced regeneration, regardless of understory treatment. The understory-left treatment could preserve understory as surviving individuals by high proportion (60% or more of the understory) compared with the understory-cleared practice after logging. However, half of the surviving individuals were damaged to some extent by logging and skidding. Relatively large trees were likely to survive with no damage, indicating that they face a lower risk than smaller trees. In understory-cleared stands, a high proportion (60% or more) of the understory regenerated by resprouting. However, the resprouting ratio depended on tree size and species. Therefore, as well as the amount of the understory, the tree size of understory before logging would be also an important factor for early forest recovery. Further, the infrequent (low-density) species could easily disappear after logging because of their low resprouting ratio and low density. Thus, recovery from resprouting alone would risk simplification of the species composition after logging. We concluded that leaving the developed understory intact before logging can enhance the speed and biodiversity of forest recovery.     

Allometric model of the Reineke equation for Japanese cypress (<Emphasis Type="Italic">Chamaecyparis obtusa</Emphasis>) and red pine (<Emphasis Type="Italic">Pinus densiflora</Emphasis>) stands

An allometric model that explains the mechanism of the difference in the slope of the Reineke equation (A) among species was proposed based on the allometric relationships of mean tree height (H) to quadratic mean diameter D (H ∝ D ^θ ) and stand density N (H ∝ N ^δ ), i.e., A = θ/δ. The proposed model was fitted to Japanese cypress (Chamaecyparis obtusa Endl.) and red pine (Pinus densiflora) stands. The allometric exponents θ and δ were, respectively, 0.8995 and −0.5000 for cypress and 0.8612 and −0.6619 for pine. The difference between cypress and pine was significant for δ but not for θ. Inserting the exponents into the model resulted in predicted slopes of −1.7991 for cypress and −1.3011 for pine. The difference in the slope of the Reineke equation between the two species was produced by characteristics related to the tree crown, rather than characteristics related to stem slenderness. The proposed model enables us to estimate the slope of the Reineke equation from commonly measured stand attributes, such as mean tree height and quadratic mean diameter. Therefore, the proposed model is expected to be practical and convenient for estimating the slope of the Reineke equation and for explaining the mechanism of its variation among species. The model should be also accepted as a generalized model of the stand density versus quadratic mean diameter relationship, whereas the original Reineke equation should be seen as a specific case of this model.     

Successful <Emphasis Type="Italic">Agrobacterium</Emphasis>-mediated transformation of <Emphasis Type="Italic">Populus tomentosa</Emphasis> with apple <Emphasis Type="Italic">SPDS</Emphasis> gene

The problem of salinized soils has become one of the most serious constraints to agricultural and forest productivity. With the purpose of enhancing salt stress tolerance of Populus tomentosa, we transformed this tree species with spermidine synthase （SPDS） genes derived from an apple by an Agrobacterium-mediated method. Four transgenic clones were confu＇med by PCR and Southern blot analysis. As well, the expression of introduced SPDS genes was analyzed by real-time quantitative PCR.     

Insecticidal properties of <Emphasis Type="Italic">Thymus persicus</Emphasis> essential oil against <Emphasis Type="Italic">Tribolium castaneum</Emphasis> and <Emphasis Type="Italic">Sitophilus oryzae</Emphasis>

Red flour beetle Tribolium castaneum (Herbst) and rice weevil Sitophilus oryzae (L.) are considered to be the major insect pests in storage. Essential oils from aromatic plants are recognized as proper alternatives to fumigants. Thymus persicus (Ronniger ex Rech. f.) is one of these plants that have medicinal properties and is indigenous to Iran. The essential oil was obtained from aerial parts of the plant and analyzed by GC and GC–MS. Carvacrol (44.69%) and thymol (11.05%) were the major constituents of the oil extracted. In this experiment, fumigant toxicity of the essential oil was studied against T. castaneum, S. oryzae at 27 ± 1°C and 60 ± 5% RH in dark condition. The adult insects were exposed to the concentrations of 51.9, 111.1, 207.4 and 370.4 μl/l air to estimate median lethal time (LT₅₀) values. The fumigant toxicity was increased in response to increased essential oil concentrations. The LT₅₀ values at the lowest and the highest concentrations tested were ranged from 28.09 to 13.47 h for T. castaneum, and 3.86 to 2.30 h for S. oryzae. It was found that S. oryzae adults were much more susceptible to the oil than T. castaneum. After 24 h of exposure, the LC₅₀ values (95% fiducial limit) for T. castaneum and S. oryzae were estimated to be 236.9 (186.27–292.81) and 3.34 (2.62–4.28) μl/l air, respectively. These results suggest that T. persicus essential oil merits further study as potential fumigant for the management of these stored-product insects.     

<Emphasis Type="Italic">Bursaphelenchus mucronatus</Emphasis> (Nematoda: Aphelenchoididae) vectored by <Emphasis Type="Italic">Monochamus </Emphasis><Emphasis Type="Italic">urussovi</Emphasis> (Coleoptera: Cerambycidae) in Hokkaido,Japan

Bursaphelenchus mucronatus Mamiya et Enda has been recovered for the first time from adults of the cerambycid beetle, Monochamus urussovi (Fischer), in Hokkaido, Japan. The nematode was also recovered from the inner bark of Picea jezoensis (Siebold et Zuccarini) Carrière and Abies sachalinensis (Fr Schmidt) Masters infested with M. urussovi larvae. PCR–RFLP analysis indicated that B. mucronatus in Hokkaido is the European type.     

Effectiveness of Neem (<Emphasis Type="Italic">Azadirachta indica</Emphasis>) insecticides against Brassica pod midge (<Emphasis Type="Italic">Dasineura brassicae</Emphasis> Winn<Emphasis Type="Italic">.</Emphasis>)

The efficiency of the botanical insecticide (BI) NeemAzal T/S (containing 1% Azadirachtin A), on the basis of azadirachtin applied in a dose of 20 g a.i. ha⁻¹ against Brassica pod midge (Dasineura brassicae), has been monitored for 4 years. The biological efficiency of BI was compared with the efficiency of some synthetic insecticides. It was ascertained that BI was very efficient in decreasing the number of damaged oilseed rape pods (ranging from 56.5 to 85.9% compared to untreated plants) and its efficiency was comparable with synthetic insecticides based on Chloronicotinyl (Thiacloprid) and Neonicotinoid (Acetamiprid). BI’s efficiency was, in some years, even significantly higher compared to pyrethroid (λ-cyhalothrin). The high biological efficiency of azadirachtin that we ascertained was significantly reflected in increasing potential crop yields. The yield increase of azadirachtin ranged between 9.3 and 19.4% compared to the control sample. Azadirachtin showed the highest yield for the whole time of experimentation, and in some years the yield increase was significantly higher compared to some synthetic agents.     

Relationships of stem surface area to other stem dimensions for Japanese cedar (<Emphasis Type="Italic">Cryptomeria japonica</Emphasis> D. Don) and Japanese cypress (<Emphasis Type="Italic">Chamaecyparis obtusa</Emphasis> Endl.) trees

I investigated the relationships between stem surface area outside bark and other stem dimensions for Japanese cedar (Cryptomeria japonica D. Don) and Japanese cypress (Chamaecyparis obtusa Endl.) trees. The stem dimensions used here were the basal area and the product of diameter at breast height (dbh) and total tree height. The regression equation of the stem surface area s against basal area g was s = 184.216g for the cedar trees and s = 156.878g for the cypress trees. The slope of the equation was significantly different between the two species. For the same dbh, the cedar trees tended to have a higher total tree height than the cypress trees. The cedar trees also had a larger surface area of relative stem form than the cypress trees. These results indicated that the difference in the slope was produced by the differences in both the stem slenderness and tapering between the two species. On the other hand, the regression equation between the stem surface area and the product of dbh and total tree height dh was s = 1.937dh for the cedar trees and s = 1.921dh for the cypress trees, whereas no significant difference in the slope was found. The obtained slopes for the cedar and cypress trees seemed to be in accord with that for other coniferous species reported in earlier studies, suggesting that the variation in the slope among coniferous species would be small. The estimation from the basal area would provide a simpler means for estimating the stem surface area and would be useful in obtaining an approximation of the surface area. By contrast, the estimation from the product of dbh and total tree height would provide a more accurate and precise estimate as well as a wider applicable range, i.e., a parameter for physiological growth models. In conclusion, it could not be judged which regression equation examined in the present study was superior to the other, and thus it was important to select an appropriate equation depending both on the purpose and on the time and labor available.     

Bioremediation of CCA-treated wood by brown-rot fungi <Emphasis Type="Italic">Fomitopsis palustris</Emphasis>, <Emphasis Type="Italic">Coniophora puteana</Emphasis>, and <Emphasis Type="Italic">Laetiporus sulphureus</Emphasis>

This study evaluated oxalic acid accumulation and bioremediation of chromated copper arsenate (CCA)-treated wood by three brown-rot fungi Fomitopsis palustris, Coniophora puteana, and Laetiporus sulphureus. The fungi were first cultivated in a fermentation broth to accumulate oxalic acid. Bioremediation of CCA-treated wood was then carried out by leaching of heavy metals with oxalic acid over a 10-day fermentation period. Higher amounts of oxalic acid were produced by F. palustris and L. sulphureus compared with C. puteana. After 10-day fermentation, oxalic acid accumulation reached 4.2 g/l and 3.2 g/l for these fungi, respectively. Fomitopsis palustris and L. sulphureus exposed to CCA-treated sawdust for 10 days showed a decrease in arsenic of 100% and 85%, respectively; however, C. puteana remediation removed only 18% arsenic from CCA-treated sawdust. Likewise, chromium removal in F. palustris and L. sulphureus remediation processes was higher than those for C. puteana. This was attributed to low oxalic acid accumulation. These results suggest that F. palustris and L. sulphureus remediation processes can remove inorganic metal compounds via oxalic acid production by increasing the acidity of the substrate and increasing the solubility of the metals.An erratum to this article can be found at