An in vitro biomechanical investigation of an intramedullary nailing technique for repair of third metacarpal and metatarsal fractures in neonates and foals

OBJECTIVE: To evaluate a dorsoproximal extra-articular approach for insertion of 8.25-mm, solid-titanium, intramedullary (IM) interlocking nails into ostectomized foal third metacarpal (MC3) and third metatarsal (MT3) bones; to compare the monotonic mechanical properties of IM nail constructs with paired intact bones; and to determine the effects of age, body weight, fore- or hindlimb, and left or right limb on the mechanical testing variables. ANIMAL OR SAMPLE POPULATION: Twenty bone pairs (10 MC3, 10 MT3) collected from 10 foals of various weights and ages. METHODS: One bone from each pair was randomly selected to be ostectomized and stabilized using an 8.25-mm, solid-titanium IM nail, and four 3.7-mm titanium interlocking screws (construct). Constructs and contralateral intact bone specimens were tested in axial compression and palmaro-/plantarodorsal (PD) 4-point bending. Monotonic mechanical properties were compared between intact specimens and constructs with an ANOVA; significance was set at P <.05. RESULTS: Nail insertion caused bone failure in 6 MC3 and 2 MT3. In general, mean mechanical testing values indicated that intact specimens were significantly stronger and stiffer than constructs for all age and weight ranges when tested in compression and PD 4-point bending (P <.05). Bone strength and stiffness of intact specimens tested in compression and bending tended to increase linearly with age and weight. CONCLUSION: IM interlocking nail fixation of gap-ostectomized MC3 and MT3 with 8.25-mm IM nails and 3.7-mm interlocking screws did not achieve sufficient strength or stiffness to be recommended as the sole means of repair for comminuted MC3 and MT3 fractures in young foals. CLINICAL RELEVANCE: IM interlocking nail fixation of foal cannon bone fractures may be useful to decrease soft-tissue disruption at the fracture site; however, there is a risk of bone failure associated with extra-articular insertion. This method should be combined with other forms of external coaptation for added stability in axial compression and PD bending.     

An in vitro biomechanical investigation of an equine interlocking nail

OBJECTIVE: To determine the mechanical properties of Equine Interlocking Nail (EIN; JD Wheat Veterinary Orthopedic Research Laboratory, University of California, Davis) stabilized osteotomized tibiae and compare these variables with estimated in vivo loads. STUDY DESIGN: In vitro biomechanical investigation. ANIMALS: Twelve adult equine cadaveric tibiae. SAMPLE POPULATION: EIN-stabilized tibiae were tested monotonically under compression, 3- and 4-point bending, and torsion. Mechanical properties were compared with estimated in vivo loads. RESULTS: EIN-tibial composite mean compressive yield load (11 kN) and bending moment (216 Nm) were greater than loads expected postoperatively in vivo; however, the mean torsional yield load (156 Nm) was less than that expected in vivo. CONCLUSIONS: EIN-stabilized tibiae had compressive and bending strengths greater than those expected to maintain stability during walking in adult horses. Torsional yield strength did not appear sufficient to provide stability during walking in vivo. CLINICAL RELEVANCE: The EIN is not a feasible method of fracture repair for adult equine tibial fractures at this time, because its mechanical properties appear inadequate to withstand the postoperative torsional loads encountered during walking. Because this method of fracture repair may offer biological advantages, further modification of an interlocking nail for adult horses appears warranted.     

An in vitro biomechanical comparison of interlocking nail constructs and double plating for fixation of diaphyseal femur fractures in immature horses

OBJECTIVE: To compare the biomechanical properties of intact immature horse femurs and 3 stabilization methods in ostectomized femurs. Animal or SAMPLE POPULATION: Eighteen pairs of femurs from immature horses aged 1 to 15 months, and weighing 68 to 236 kg. METHODS: Thirty-four immature horse femurs were randomly assigned to 1 of 5 test groups: 1) interlocking intramedullary nail (IIN) (n = 6); 2) IIN with a cranial dynamic compression plate (I/DCP) (n = 6); 3) 2 dynamic compression plates (2DCP) (n = 8); 4) intact femurs tested to failure in lateromedial (LM) bending (n = 6); and 5) intact femurs tested to failure in caudocranial (CaCr) bending (n = 8). Mid-diaphyseal ostectomies (1 cm) were performed in all fixation constructs. Biomechanical testing consisted of 4 nondestructive tests: CaCr bending, LM bending, compression, and torsion, followed by bending to failure. All groups were tested to failure in LM bending with the exception of 1 group of intact femurs tested to failure in CaCr bending. Stiffness and failure properties were compared among groups. RESULTS: The 2DCP-femur construct had greater structural stiffness in nondestructive bending than the IIN-femur construct in either LM or CaCr bending, and the I/DCP-femur construct in LM bending. Only the I/DCP and 2DCP fixations were similar to intact bone in nondestructive-bending tests. In addition, the 2DCP-femur construct had greater structural and gap torsional stiffness than the I/DCP-femur construct, and greater gap torsional stiffness than the IIN-femur construct. However, all of the fixation methods tested, including the 2DCP-femur construct, had lower structural stiffness in torsional loading compared with intact bone. No significant differences in structural stiffness were found between intact bones and femur constructs tested nondestructively in compression. In resistance to LM bending to failure, the 2DCP-femur construct was superior to the IIN-femur construct, yet similar to the I/DCP-femur construct. Also, evaluation of yield and failure loads revealed no significant differences between intact bone and any of the femur constructs tested to failure in LM bending. CONCLUSIONS: In general, the 2DCP-femur construct provided superior strength and stiffness compared with the IIN and I/DCP-femur constructs under bending and torsion. CLINICAL RELEVANCE: Double plating of diaphyseal comminuted femoral fractures in immature horses may be the best method of repair, because in general, it provides the greatest strength and stiffness in bending and torsion.     

In vitro cyclic biomechanical properties of an interlocking equine tibial nail

OBJECTIVE: To determine cyclic biomechanical properties of gap osteotomized adult equine tibiae stabilized with an equine interlocking nail (EIN). STUDY DESIGN: In vitro experimental biomechanical investigation. SAMPLE POPULATION: Thirteen adult equine cadaveric tibiae. METHODS: Adult equine tibiae with transverse, midshaft, 1-cm gap osteotomies, stabilized with an equine interlocking nail, underwent cyclic biomechanical testing in vitro under axial compression, 4-point bending, and torsion. Different specimens were subjected to different load levels that represented estimated in vivo loads at 2 Hz for 740,000 cycles. Fatigue life and gap strain were calculated. RESULTS: Compression and bending, but not torsional, fatigue life were longer than time necessary for bone healing. Compressive, but not bending or torsional, gap strains were small enough to be compatible with fracture healing by primary bone formation. Gap strains for compressive, bending, and torsional loads were compatible with indirect, or secondary, bone formation. CONCLUSIONS: Further modification should be made to the equine interlocking nail to increase bending stiffness and torsional fatigue life. CLINICAL RELEVANCE: The stainless steel equine intramedullary interlocking nail is unlikely to provide appropriate long-term stability for fracture healing in adult equine tibiae without modifications in the nail design and material.     

An in vitro biomechanical comparison of two interlocking-nail systems for fixation of ostectomized equine third metacarpal bones

OBJECTIVE--To compare the mechanical properties of 2 interlocking-nail systems for fixation of ostectomized equine third metacarpi (MC3): (1) a standard interlocking nail with 2 parallel screws proximal and distal to a 1-cm ostectomy; and (2) a modified interlocking nail with 2 screws proximal and distal to a 1-cm ostectomy with the screws offset by 30 degrees. ANIMAL OR SAMPLE POPULATION--Twelve pairs of adult equine forelimbs intact from the midradius distally. METHODS--Twelve pairs of equine MC3 were divided into 2 test groups (6 pairs each): torsion and caudocranial 4-point bending. Standard interlocking nails (6-hole, 13-mm diameter, 230-mm length) were placed in 1 randomly selected bone from each pair. Modified interlocking nails (6-hole, 13-mm, 230-mm length, screw holes offset by 30 degrees) were placed in the contralateral bone from each pair. All bones had 1-cm mid-diaphyseal ostectomies. Six construct pairs were tested in caudocranial 4-point bending to determine stiffness and failure properties. The remaining 6 construct pairs were tested in torsion to determine torsional stiffness and yield load. Mean values for each fixation method were compared using a paired t test within each group. Significance was set at P <.05. RESULTS--Mean (+/-SEM) values for the MC3-standard interlocking-nail composite and the MC3-modified interlocking-nail composite, respectively, in 4-point bending were: composite rigidity, 3,119 +/- 334.5 Nm/rad (newton. meter/radian) and 3,185 +/- 401.2 Nm/rad; yield bending moment, 205.0 +/- 18.46 Nm and 186.7 +/- 6.17 Nm; and failure bending moment, 366.4 +/- 21.82 Nm and 378.1 +/- 20.41 Nm. There were no significant differences in the biomechanical values for bending between the 2 fixation methods. In torsion, mean (+/-SEM) values for the MC3-standard interlocking-nail composite and the MC3-modified interlocking-nail composite were: composite rigidity, 135.5 +/- 7.128 Nm/rad and 112.5 +/- 7.432 Nm/rad; gap stiffness, 207.6 +/- 10.57 Nm/rad and 181.7 +/- 12.89 Nm/rad; and yield load, 123.3 +/- 2.563 Nm and 107.5 +/- 8.353 Nm, respectively. Composite rigidity and gap stiffness for standard interlocking-nail fixations were significantly higher than the modified interlocking-nail fixation technique in torsion. Yield load had a tendency to be higher for the standard interlocking-nail fixation (P =.15). CONCLUSIONS--No significant differences in biomechanical properties were identified between a standard interlocking nail and one with the screw holes offset by 30 degrees in caudocranial 4-point bending. The standard interlocking nail was superior to the modified interlocking nail in torsional gap stiffness and composite rigidity. The torsional yield load also tended to be higher for the standard interlocking nail. CLINICAL RELEVANCE--The standard interlocking nail with parallel screw holes is superior to a modified interlocking nail with the screw holes offset by 30 degrees in ostectomized equine MC3 bones in vitro when tested in torsion.     

Long incomplete longitudinal fractures of the third metacarpal and metatarsal bone in horses

Five horses with long incomplete longitudinal fractures of the third metacarpal bone and three horses with similar fractures of the third metatarsal bone were examined. In three of the metacarpal fractures a long incomplete fissure extended proximomedially, in association with the more common lateral condylar fracture of the third metacarpal bone, and in the other two cases the fracture originated from the medial aspect of the distal articular surface. In the three horses with fractures of the third metatarsal bone the fractures had a consistent spiral configuration.     

Nuclear scintigraphic evaluation of third metacarpal and metatarsal bone fractures in three horses

Nuclear scintigraphy was used to evaluate healing of third metacarpal bone (MC III) fractures in 2 horses (horses 1 and 2) and a third metatarsal bone fracture in 1 horse (horse 3) after stabilization of each fracture with 2 broad dynamic compression plates. In horse 1, the fracture had uniform uptake of 99mTc methylene diphosphonate on days 1, 15, and 30 after surgery. The fracture healed, and the horse was discharged from the clinic on day 52. In horse 2, a 6-cm photopenic region (ie, area of low radioactivity) was seen over the diaphysis of MC III on day 3. The region persisted and became more distinct by day 32. The diaphysis of MC III sequestered, and horse 2 was euthanatized on day 44. In horse 3, vascularity was seen bridging the fracture on day 5, with a 3-cm photopenic region over the dorsal diaphysis of the third metatarsal bone. By days 18 and 32, uptake of 99mTc methylene diphosphonate in the region had increased, indicating vascularization of the site. the fracture healed, and horse 3 was discharged from the clinic on day 47. Our findings indicated that serial nuclear scintigraphy can be used to evaluate fracture vascularization after surgery in horses.     

Technique for arthroscopic repair of third carpal bone slab fractures in horses

A technique involving internal fixation guided by arthroscopy was used to repair third carpal slab fractures in 23 horses. The technique allowed good reduction and compression of the fractures, with minimal surgical trauma. Ten of 17 horses with a 6-month or longer follow-up have returned to race successfully.     

An in vitro biomechanical study of bone plate and interlocking nail in a canine diaphyseal femoral fracture model

OBJECTIVE: To compare the structural properties and the interfragmentary motion in ostectomized canine femurs stabilized with either an 8-mm interlocking nail system (IN) or a 10-hole dynamic compression broad plate (DCP). ANIMAL OR SAMPLE POPULATION: Ten pairs of adult canine femurs with a 25-mm mid-diaphyseal gap. METHODS: Bone specimens were divided into 2 groups (10 femurs each). Left femurs were stabilized with a DCP and 8 bicortical screws; right femurs were stabilized with an IN and 3 screws. Mechanical tests were performed in eccentric axial loading and in craniocaudal bending. The testing was first conducted nondestructively and then until breakage. Structural properties, ie, stiffness, yield limits, and failure limits, were determined. Interfragmentary motion was measured during nondestructive tests with the use of an optoelectronic device. Axial, transverse, and rotational motions were calculated. Mean values of stiffness, yield and failure limits, and axial and shear motions for each fixation method were compared using a paired t test within each group (P <.05). RESULTS: Mean (+/-SD) values of stiffness and failure limit were significantly higher for IN constructs than for DCP constructs in compression, while there was little difference in the results between each tested group in bending. Mean yield load values were significantly higher for IN than for DCP specimens in compression as well as in bending. The axial-motion analysis revealed significant differences between IN and DCP groups during bending tests only. The highest score of transverse motion at the gap was recorded during bending tests, and was higher for DCP than for IN specimens. There were insignificant differences between the two groups with regard to rotation around the diaphyseal axis. CONCLUSIONS AND CLINICAL RELEVANCE: Structural properties and interfragmentary shear motion analysis demonstrated a much higher rigidity in the IN-bone than in the DCP-bone constructs.     

An in vitro biomechanical comparison between prototype tapered shaft cortical bone screws and AO cortical bone screws for an equine metacarpal dynamic compression plate fixation of osteotomized equine third metacarpal bones

OBJECTIVES: To compare biomechanical properties of a prototype 5.5 mm tapered shaft cortical screw (TSS) and 5.5 mm AO cortical screw for an equine third metacarpal dynamic compression plate (EM-DCP) fixation to repair osteotomized equine third metacarpal (MC3) bones. STUDY DESIGN: Paired in vitro biomechanical testing of cadaveric equine MC3 with a mid-diaphyseal osteotomy, stabilized by 1 of 2 methods for fracture fixation. ANIMAL POPULATION: Adult equine cadaveric MC3 bones (n=12 pairs). METHODS: Twelve pairs of equine MC3 were divided into 3 groups (4 pairs each) for (1) 4-point bending single cycle to failure testing, (2) 4-point bending cyclic fatigue testing, and (3) torsional single cycle to failure testing. An EM-DCP (10-hole, 4.5 mm) was applied to the dorsal surface of each, mid-diaphyseal osteotomized, MC3 pair. For each MC3 bone pair, 1 was randomly chosen to have the EM-DCP secured with four 5.5 mm TSS (2 screws proximal and distal to the osteotomy; TSS construct), two 5.5 mm AO cortical screws (most proximal and distal holes in the plate) and four 4.5 mm AO cortical screws in the remaining holes. The control construct (AO construct) had four 5.5 mm AO cortical screws to secure the EM-DCP in the 2 holes proximal and distal to the osteotomy in the contralateral bone from each pair. The remaining holes of the EM-DCP were filled with two 5.5 mm AO cortical screws (most proximal and distal holes in the plate) and four 4.5 mm AO cortical screws. All plates and screws were applied using standard AO/ASIF techniques. Mean test variable values for each method were compared using a paired t-test within each group. Significance was set at P<.05. RESULTS: Mean 4-point bending yield load, yield bending moment, bending composite rigidity, failure load and failure bending moment of the TSS construct were significantly greater (P<.00004 for yield and P<.00001 for failure loads) than those of the AO construct. Mean cycles to failure in 4-point bending of the TSS construct was significantly greater (P<.0002) than that of the AO construct. The mean yield load and composite rigidity in torsion of the TSS construct were significantly greater (P<.0039 and P<.00003, respectively) than that of the AO construct. CONCLUSION: The TSS construct provides increased stability in both static overload testing and cyclic fatigue testing. CLINICAL RELEVANCE: The results of this in vitro study support the conclusion that the EM-DCP fixation using the prototype 5.5 mm TSS is biomechanically superior to the EM-DCP fixation using 5.5 mm AO cortical screws for the stabilization of osteotomized equine MC3.     

In vitro biomechanical comparison of a plate-rod combination-construct and an interlocking nail-construct for experimentally induced gap fractures in canine tibiae

OBJECTIVE: To compare structural properties of a plate-rod combination-bone construct (PRCbc) and interlocking nail-bone construct (ILNbc) by use of an experimentally induced gap fracture in canine tibiae. SAMPLE POPULATION: 12 paired canine tibiae. PROCEDURE: Specimens were implanted with a plate-rod combination consisting of a 3.5-mm, limited-contact, dynamic-compression plate combined with an intramedullary rod or 6-mm interlocking nail. Ostectomy (removal of 10-mm segment) was performed. Paired constructs were loaded for bending, compression, or torsion measurements (4 constructs/group). Compliance was determined by fitting regression lines to the load-position curves at low (initial compliance) and high (terminal compliance) loads. RESULTS: Bending compliances did not differ significantly between constructs. For the ILNbc, initial compliance was greater than terminal compliance in compression and torsion. Initial compliance and terminal compliance for the PRCbc were similar in compression and torsion. Initial compliance in compression and torsion was greater for the ILNbc, compared with initial compliance for the PRCbc. Maximum deformations in bending and compression were similar between constructs; however, maximum torsional angle was significantly greater for the ILNbc, compared with values for the PRCbc. CONCLUSIONS AND CLINICAL RELEVANCE: The study documented that for an experimentally induced gap fracture in canine tibiae, a plate-rod combination is a significantly less compliant fixation method in torsion and compression, compared with an interlocking nail. Considering the deleterious effects of torsional deformation on bone healing, a plate-rod combination may represent a biomechanically superior fixation method, compared with an interlocking nail, for the treatment of dogs with comminuted tibial diaphyseal fractures.     

An in vitro biomechanical comparison of a prototype equine metacarpal dynamic compression plate fixation with double dynamic compression plate fixation of osteotomized equine third metacarpal bones

OBJECTIVES: To compare the monotonic biomechanical properties of a prototype equine third metacarpal dynamic compression plate (EM-DCP) fixation with a double broad dynamic compression plate (DCP) fixation to repair osteotomized equine third metacarpal (MC3) bones. STUDY DESIGN: In vitro biomechanical testing of paired cadaveric equine MC3 with a mid-diaphyseal osteotomy, stabilized by 1 of 2 methods for fracture fixation. POPULATION: Twelve pairs of adult equine cadaveric MC3 bones. METHODS: Twelve pairs of equine MC3 were divided into 3 test groups (4 pairs each) for (1) 4-point bending single cycle to failure testing, (2) 4-point bending cyclic fatigue testing, and (3) torsional testing. The EM-DCP (10-hole, 4.5 mm) was applied to the dorsal surface of one randomly selected bone from each pair. Two DCPs, 1 dorsally (10-hole, 4.5 mm broad) and 1 laterally (9-hole, 4.5 mm broad) were applied to the contralateral bone from each pair. All plates and screws were applied using standard AO/ASIF techniques to MC3 bones that had mid-diaphyseal osteotomies. Mean test variable values for each method were compared using a paired t-test within each group. Significance was set at P<.05. RESULTS: Mean 4-point bending yield load, yield bending moment, bending composite rigidity, failure load and failure bending moment of the EM-DCP fixation were significantly greater (P<.0001) than those of the double broad DCP fixation. Mean cycles to failure in 4-point bending of the EM-DCP fixation was significantly greater (P<.0008) than that of the double broad DCP fixation. Mean yield load, composite rigidity, and failure load in torsion of the EM-DCP fixation were significantly greater (P<.0035) than that of the double broad DCP fixation. CONCLUSION: The EM-DCP provides increased stability in both static overload testing and cyclic fatigue testing. CLINICAL RELEVANCE: Results of this in vitro study support the conclusion that the prototype EM-DCP fixation is biomechanically superior to the double broad DCP fixation for the stabilization of osteotomized equine MC3.     

In vitro comparison of three fixation methods for humeral fracture repair in adult horses

The stiffness, load to failure, and bending moments of adult intact equine humeri and humeri repaired with 3 fixation techniques were determined in vitro. Bones were tested in axial compression (30 pairs), mediolateral 3-point bending (15 pairs), and caudocranial 3-point bending (15 pairs). An oblique osteotomy of 1 humerus of each pair was performed to simulate the long spiral oblique fractures that occur clinically in horses. Bones were repaired in 3 ways: group 1--nylon band cerclage fixation (20 bones); group 2--multiple intramedullary pinning (20 bones); and group 3--nylon band cerclage fixation and multiple intramedullary pinning (20 bones). Intact bones were significantly (P less than 0.05) stronger than repaired bones in each testing mode. Bones repaired with bands only were significantly less stiff in bending than were bones repaired with pins only or with pins and bands. In compression, only specimens repaired with pins and bands were significantly stiffer than were bones repaired with bands only. Bones repaired with bands only required significantly less load to failure in compression and in caudocranial bending than did bones repaired with pins only or with pins and bands. Bones repaired with pins only deformed through the full displacement of the actuator (5 cm), and pins deformed plastically. Bones repaired with pins and bands were stiffer and had higher bending moments than did bones repaired with pins only, but the differences were not significant.     

In vitro biomechanical properties of 2 compression fixation methods for midbody proximal sesamoid bone fractures in horses

OBJECTIVE: To evaluate 2 methods of midbody proximal sesamoid bone repair--fixation by a screw placed in lag fashion and circumferential wire fixation--by comparing yield load and the adjacent soft-tissue strain during monotonic loading. STUDY DESIGN: Experimental study. SAMPLE POPULATION: 10 paired equine cadaver forelimbs from race-trained horses. METHODS: A transverse midbody osteotomy of the medial proximal sesamoid bone (PSB) was created. The osteotomy was repaired with a 4.5-mm cortex bone screw placed in lag fashion or a 1.25-mm circumferential wire. The limbs were instrumented with differential variable reluctance transducers placed in the suspensory apparatus and distal sesamoidean ligaments. The limbs were tested in axial compression in a single cycle until failure. RESULTS: The cortex bone screw repairs had a mean yield load of 2,908.2 N; 1 limb did not fail when tested to 5,000 N. All circumferential wire repairs failed with a mean yield load of 3,406.3 N. There was no statistical difference in mean yield load between the 2 repair methods. The maximum strain generated in the soft tissues attached to the proximal sesamoid bones was not significantly different between repair groups. CONCLUSIONS: All repaired limbs were able to withstand loads equal to those reportedly applied to the suspensory apparatus in vivo during walking. CLINICAL RELEVANCE: Each repair technique should have adequate yield strength for repair of midbody fractures of the PSB immediately after surgery.     

Use of a new investigational interlocking nail supplement in the repair of comminuted diaphyseal tibia fractures in two dogs

Two dogs were diagnosed with highly comminuted diaphyseal tibial fractures following traumatic incidents. Investigational hybrid interlocking nail (ILN) bolt/external skeletal fixator (ESF) pins were used to repair both fractures. The surgery was successful, and fractures healed without complications by 6 weeks (case no. 1) and 17 weeks (case no. 2) after surgery. This article describes the application and the advantages of a new, investigational ILN supplement that was specifically designed to accomplish initial rigid stability and allow progressive destabilization to the fracture repair. The authors are continuing to study the biomechanical properties of this procedure in order to accurately establish clear recommendations for its use in certain fracture situations.     

Evaluation of transfixation casting for treatment of third metacarpal, third metatarsal, and phalangeal fractures in horses: 37 cases (1994-2004)

OBJECTIVE: To evaluate clinical findings, complications, and outcome of horses and foals with third metacarpal, third metatarsal, or phalangeal fractures that were treated with transfixation casting. DESIGN: Retrospective case series. Animals-29 adult horses and 8 foals with fractures of the third metacarpal or metatarsal bone or the proximal or middle phalanx. PROCEDURES: Medical records were reviewed, and follow-up information was obtained. Data were analyzed by use of logistic regression models for survival, fracture healing, return to intended use, pin loosening, pin hole lysis, and complications associated with pins. RESULTS: In 27 of 35 (77%) horses, the fracture healed and the horse survived, including 10 of 15 third metacarpal or metatarsal bone fractures, 11 of 12 proximal phalanx fractures, and 6 of 8 middle phalanx fractures. Four adult horses sustained a fracture through a pin hole. One horse sustained a pathologic unicortical fracture secondary to a pin hole infec-tion. Increasing body weight, fracture involving 2 joints, nondiaphyseal fracture location, and increasing duration until radiographic union were associated with horses not returning to their intended use. After adjusting for body weight, pin loosening was associated with di-aphyseal pin location, pin hole lysis was associated with number of days with a transfixation cast, and pin complications were associated with hand insertion of pins. CONCLUSIONS AND CLINICAL RELEVANCE: Results indicated that transfixation casting can be successful in managing fractures distal to the carpus or tarsus in horses. This technique is most suitable for comminuted fractures of the proximal phalanx but can be used for third metacarpal, third metatarsal, or middle phalanx fractures, with or without internal fixation.     

An in vitro biomechanical comparison of a limited-contact dynamic compression plate fixation with a dynamic compression plate fixation of osteotomized equine third metacarpal bones

OBJECTIVES: To compare the monotonic biomechanical properties and fatigue life of a broad, limited contact, dynamic compression plate (LC-DCP) fixation with a broad, dynamic compression plate (DCP) fixation to repair osteotomized equine 3rd metacarpal (MC3) bones. STUDY DESIGN: In vitro biomechanical testing of paired cadaveric equine MC3 with a mid-diaphyseal osteotomy, stabilized by 1 of 2 methods for fracture fixation. ANIMAL POPULATION: Twelve pairs of adult equine cadaveric MC3 bones. METHODS: Twelve pairs of equine MC3 were divided into 3 test groups (4 pairs each) for (1) 4-point bending single cycle to failure testing, (2) 4-point bending cyclic fatigue testing, and (3) torsional single cycle to failure testing. An LC-DCP (8-hole, 4.5 mm) was applied to the dorsal surface of 1 randomly selected bone from each pair. One DCP (8-hole, 4.5 mm broad) was applied dorsally to the contralateral bone from each pair. All plates and screws were applied using standard AO/ASIF techniques to MC3 bones that had mid-diaphyseal osteotomies. Mean test variable values for each method were compared using a paired t-test within each group. Significance was set at P<.05. RESULTS: The mean 4-point bending yield load, yield bending moment, composite rigidity, failure load, and failure bending moment of LC-DCP fixation were significantly greater (P<.01) than those of broad DCP fixation. Mean cycles to failure for 4-point bending was significantly (P<.001) greater for broad DCP fixation compared with broad LC-DCP fixation. Mean yield load, mean composite rigidity, and mean failure load in torsion was significantly (P<.02) greater for broad LC-DCP fixation compared with broad DCP fixation. CONCLUSION: Broad LC-DCP offers increased stability in static overload testing, however, it offers significantly less stability in cyclic fatigue testing. CLINICAL RELEVANCE: The clinical relevance of the cyclic fatigue data supports the conclusion that the broad DCP fixation is biomechanically superior to the broad LC-DCP fixation in osteotomized equine MC3 bones despite the results of the static overload testing.     

Results of treatment of 145 fractures of the third metacarpal/metatarsal condyles in 135 horses (1986-1994).

The objectives of this study were to correlate condylar fracture characteristics and type of treatment with subsequent capacity for athletic ability, and to determine the characteristics of healing that affect prognosis after fracture fixation. Medical records, post operative radiographic studies and race records were examined for 135 horses sustaining 145 fractures. Sixty-five percent of horses overall started in a race post injury (SPI) in a mean time of 9.7 months with a mean of 13.7 races post injury. Having raced pre-injury did not confer an advantage to starting post injury, though nonstarters pre-injury tended to take longer to return. For horses starting pre- and post injury, 66% improved or maintained their race class level after injury, whereas 64.2% decreased their race earnings post injury. Eighty-five percent of the fractures received internal fixation, of which 70% were complete fractures. Eighty-seven percent of horses with incomplete-nondisplaced fractures treated conservatively raced post injury. The percent SPI for incomplete-nondisplaced, complete-nondisplaced and complete-displaced fractures treated with internal fixation were 74%, 58%, and 60%, respectively. Males (72%) raced post injury more frequently than fillies (53%), and may represent a truer probability of SPI. Spiral fractures tended to take longer until their first start (mean 13.3 months). Fifty-two percent of horses with articular fragments were able to race post injury. Horses were more likely to start if 2-4 month radiographic healing revealed no evidence of the fracture except the presence of lag screws. Based on this series of cases, the majority of horses, with proper treatment, were able to return to racing regardless of fracture characteristic. Prognosis appeared to be affected by the severity of the injury to the joint, the presence of articular comminution and the quality of surgical repair.     

Surgical management of complete diaphyseal third metacarpal and metatarsal bone fractures: Clinical outcome in 10 mature horses and 11 foals

Reasons for performing study: Osteosynthesis of third metacarpal (McIII) and third metatarsal (MtIII) bone fractures in horses is a surgical challenge and complications surrounding the repair are common. Retrospective studies evaluating surgical repair, complications and outcome are necessary to increase knowledge and improve success of long bone fracture repair in the horse. Objectives: To evaluate clinical findings, surgical repair, post operative complications and outcome of 10 mature horses and 11 foals with McIII or MtIII fractures that were treated with open reduction and internal fixation (ORIF). Methods: Medical records were reviewed and follow‐up information obtained by means of radiographs and/or telephone questionnaire. Results: Survival was achieved in 62% of the horses (3 mature/10 foals). On long‐term evaluation (>6 months) 11 horses (2 mature/9 foals) were fit for their intended activity, one mature horse had a chronic low grade lameness, and one foal was lost to follow‐up because it was sold. The main fracture types were simple transverse (33.3%) or simple oblique (28.6%) and 71.4% of the fractures were open, 3 Type I (one mature/2 foals) and 12 type II (7 mature/5 foals). The preoperative assessment revealed inadequate emergency treatment in 10 horses (5 mature/5 foals; 47.6%). Survival rate of horses with open fractures was 12.5% (1/8) in mature and 85.7% (6/7) in foals. Post operative incisional infection (4 mature, 3 foals) was only managed successfully in 2 foals. Fracture instability related to inadequate fracture fixation technique occurred in 4 horses (all mature) and was always associated with unsuccessful outcome. Conclusions: Age, bodyweight and infection are strongly associated with outcome in treatment of complete McIII/MtIII fractures. Clinical relevance: Rigid fixation using plates and screws can be successful in treatment of closed or open, complete diaphyseal McIII/MtIII fractures in mature horses and foals. Instable fixation, infection and a bodyweight >320 kg are major risk factors for unsuccessful outcome.