Preparation and UV-protective property of PVAc/ZnO and PVAc/TiO<Subscript>2</Subscript> microcapsules/poly(lactic acid) nanocomposites

The poly(vinyl acetate) (PVAc)/zinc oxide (ZnO) microcapsule and PVAc/titanium dioxide (TiO₂) microcapsule were synthesized via in-situ emulsion polymerization method. The PVAc/ZnO microcapsule and PVAc/TiO₂ microcapsule were characterized by fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis(TG), transmission electron microscopy (TEM), and UV-visible spectroscopy (UV-vis). Effect of PVAc/ZnO microcapsule and PVAc/TiO₂ microcapsule on properties of poly(lactic acid) (PLA) was evaluated by UV-vis, SEM and mechanical properties test. The results showed that the addition of PVAc/ZnO and PVAc/TiO₂ microcapsules as a UV-blocking additive could significantly enhance UV-blocking property of PLA/PVAc/ZnO microcapsule composites and PLA/PVAc/TiO₂ microcapsule composites compared with pure PLA, PLA/ZnO composites and PLA/TiO₂ composites. The mechanical properties of PLA/PVAc/ZnO microcapsule composites were better than those of PLA/ZnO composites due to good dispersability and compatibility of PVAc/ZnO microcapsule in PLA matrix. Also, the mechanical properties of PLA/PVAc/TiO₂ microcapsule composites were better than those of pure PLA and PLA/TiO₂ composites. This study demonstrates the great potentials of the intrinsically UV shield additive PVAc/ZnO and PVAc/TiO₂ microcapsules in the application of high performance matrix resin and composite material.     

Fabrication and characterization of nano Al<Subscript>2</Subscript>O<Subscript>3</Subscript> filled PVA:NH<Subscript>4</Subscript>SCN electrolyte nanofibers by electrospinning

Present paper reports a method of preparing polymer composite electrolyte nanofiber mat using polyvinyl alcohol (PVA), ammonium thiocynate (NH₄SCN) salt, and aluminium oxide (Al₂O₃) nano particles based on electrospinning technique. Two-stage process of preparation of nanofibers, namely, preparation of nano particles filled PVA electrolyte gel solution followed by its electrospinning has been used. The so obtained nanofibers have been characterized by XRD, DSC, SEM, and Conductivity measurements. XRD patterns affirm the formation of nanocomposite while SEM pictures reveal formation of fibers on a nano scale format (300–800 nm). Fibers of the electrolytes are seen to be thermally stable. Ionic conductivity of electrolyte fiber is seen to improve in the presence of nano filler at room temperature with a maximum at 5.31×10⁻³ Scm⁻¹ for 4 wt% filler concentration, which is comparable to that for corresponding dried gel electrolyte films.     

Enhanced physico-mechanical properties of polyester resin film using CaCO<Subscript>3</Subscript> filler

Bio-based CaCO₃ powder was synthesized via size reduction method from waste eggshells. The XRD analysis revealed that eggshell powder consists of CaCO₃ in calcite form. The inclusion level of CaCO₃ contents were varied of 5, 10, 15, 20 and 25 wt.% of prepared CaCO₃-polyester film. Effects of different proportions of prepared chicken eggshell and commercial CaCO₃ filler on the polyester resin composites films were compared by means of mechanical and physical test. It was found that the addition of CaCO₃ filler to the polyester films leads to improve the mechanical properties. The findings revealed that the best and optimum CaCO₃ filler content was 10 wt.% and among the prepared polyester films, eggshell CaCO₃-polyester films showed the best performance. The mechanical properties of CaCO₃-polyester films were measured in terms of tensile strength, elongation-at-break, tensile modulus, flexural strength and impact strength. For eggshell CaCO₃- polyester films, the maximum values of the aforementioned mechanical properties were 52.70 MPa, 4.63 %, 1868.70 MPa, 101.20 MPa and 8.40 kJ/m², respectively, whereas for commercial CaCO₃-polyester films those values were 48.12 MPa, 4.50 %, 1790.30 MPa, 97.50 MPa and 8.21 kJ/m², respectively. Further, water absorption of the composite films as a function of time had also been investigated at 10 wt.% filler content.     

Ladder-Structured Polysilsesquioxane/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Nanocomposites for Transparent Wear-Resistant Windows

As a protective layer for deformable displays, we synthesized ladder-type polysilsesquioxanes (LPSQs) containing cyclic epoxy as a curable unit. The mechanical properties after photo- and thermal-curing of LPSQs with a small amount of added Al₂O₃ nanoparticles were compared with those of the pure LPSQs. The prepared LPSQ-Al₂O₃ nanocomposites and the pure LPSQs exhibited comparable optical transparencies and thermal stabilities. In addition, the degree of conversion of the applied epoxy units in LPSQs and the resulting mechanical properties, as monitored by Fourier transform infrared spectroscopy and nanoindentation tests, indicated that the addition of nanoparticles to LPSQs moderately enhanced the epoxy conversion rate and remarkably improved the wear resistance, including hardness, after photo-/thermal-curing processes. The LPSQ-Al₂O₃ nanocomposites achieved higher wear resistance than epoxy-silica nanocomposites containing similar curable functional groups and reinforcing fillers (silica). The excellent mechanical properties of the LPSQ-Al₂O₃ nanocomposites could be attributed to three-dimensionally interconnected networks of organic-inorganic hybrid-type chemical structures in the LPSQ as well as additional reinforcement from amine-functionalized Al₂O₃ nanoparticles covalently interconnected with the LPSQ. We believe that the devised LPSQ-Al₂O₃ nanocomposites could serve effectively as a wear-resistant platform for deformable display windows.     

Load of Ag<Subscript>3</Subscript>PO<Subscript>4</Subscript> Particles on Sulfonated Polyphenylene Sulfide Superfine Fibre with High Visible-light Photocatalytic Activity

Ag₃PO₄ was loaded on sulfonated polyphenylene sulfide (SPPS) superfine fibre by a facile precipitation method. Both the structure and properties of the as-synthesized Ag₃PO₄/SPPS composites were characterized via XRD, SEM, EDS, XPS, FTIR, and UV-vis. The photocatalytic performance of Ag₃PO₄/SPPS composites was investigated via degradation of Methylene blue(MB) solution under visible light irradiation. The degradation results revealed that the photocatalytic activity of Ag₃PO₄/SPPS composites was greatly enhanced by the incorporation of Ag₃PO₄ with SPPS superfine fibre. For concentrations of AgNO₃ and Na₂HPO₄ solutions of 0.3 M and 0.06 M in the preparation process, the Ag₃PO₄/SPPS composite showed higher photocatalytic activity under visible light irradiation.     

Preparation of magnetic and conductive graphite nanoflakes/SrFe<Subscript>12</Subscript>O<Subscript>19</Subscript>/polythiophene nanofiber-nanocomposites and its radar absorbing application

This study, we synthesized graphite-nanoflakes (GNFs) by acid treatment and thermal shock and then using the ultrasonic irradiation technique to exfoliate flake-carbon. The SrFe₁₂O₁₉ nanoparticles (NPs) were coated by co-precipitate method on GNFs after by alkaline treatment. Finally nanocomposite (GNF/SrFe₁₂O₁₉/PTh) was prepared by in-situ oxidative polymerization method in presence of thiophene (Th) as monomer. The magnetic and electrical conducting properties of the resulting nanocomposites were measured by using vibrating sample magnetometer and standard four-point-probe method, respectively. The synthesized nanocomposites were characterized by X-ray diffraction (XRD) and fourier transform infrared spectra (FTIR). In addition, morphological analyses were investigated by scanning electron microscopy (SEM). A minimum reflection loss (RL) of GNFs/SrFe₁₂O₁₉/PTh with 50 % wt GNFs/SrFe₁₂O₁₉ as core were observed ?28 and ?39 dB at 9.7 and 12 GHz for a 1.5 mm thickness. The results indicated that we can perform good microwave shielding in X-band (8–12 GHz) by these nanocomposites.     

Fabrication and Characterisation of Functionalised Superparamagnetic Bacterial Nanocellulose Using Ultrasonic-Assisted <Emphasis Type="Italic">In Situ</Emphasis> Synthesis

Ultrasonic-assisted in situ synthesis was performed using bacterial nanocellulose (BNC) and magnetite nanoparticles (Fe₃O₄ NPs) to synthesise superparamagnetic membranes as BNC/Fe₃O₄ nanocomposite films (BNC/Fe₃O₄ NCFs). Vibrating sample magnetometry of these BNC/Fe₃O₄ NCFs exhibited superparamagnetic properties with high saturation magnetisation at 40.57 emu g^-1. Morphology of BNC/Fe₃O₄ NCFs was studied by field-emission scanning electron microscopy. Results showed Fe₃O₄ NPs with diameter 30 to 50 nm trapped in a BNC structure. Fourier transform infrared spectroscopy analysis confirmed the incorporation of BNC and Fe₃O₄ NPs. Thermal properties of the nanocomposite films increased with Fe₃O₄ NPs in the BNC structure compared with native BNC. Surface wettability of BNC/Fe₃O₄ NCFs was determined by contact angle and revealed hydrophobic properties. Results showed that ultrasonic-assisted in situ synthesis of superparamagnetic BNC/Fe₃O₄ NCFs is an important property when utilising BNC/Fe₃O₄ NCFs with a hydrophobic nonpolar polymeric matrix in electronic device applications.     

Effect of phase transformation on physical and biological properties of PVA/CaFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanocomposite

The thermal treatment method was employed to achieve higher homogeneity of calcium ferrite (CaFe2O4) and Poly (vinyl alcohol) (PVA) nanocomposites. The influences of phase transformation on physical and biological properties of calcined specimens were investigated by various experimental techniques including X-ray diffraction (XRD), Transmission Electron Microscopy (TEM), high resolution Field emission scanning electron microscope (FESEM) and Fourier transform infrared spectroscopy (FT-IR). Heat treatment was conducted at temperatures between 723 and 923 K, so that a phase transformation occurred from cubic to orthorhombic spinel structure at 923 K. The chemical analysis of the PVA/CaFe₂O₄ nanocomposite was performed by energy dispersion X-ray analysis (EDXA), demonstrated the PVA/CaFe₂O₄ nanocomposites contained the elements of C, Ca, Fe, and O. The formed nanocomposites exhibited ferromagnetic behaviors which were confirmed by using a vibrating sample magnetometer (VSM). The calcined specimens were carried out to an antimicrobial or antifungal test.     

The synergy effect of Graphene/SiO<Subscript>2</Subscript> hybrid materials on reinforcing and toughening epoxy resin

Based on the situ preparation of silica nanoparticles (SiO₂) on the surface of Graphene nanoplatelets (GNPs) in the previous work, these unique three dimensional (3D) materials were introduced into epoxy resin to study the reinforcing and toughening synergy effect on the composites. Firstly, the tensile tests showed that Graphene/SiO₂ hybrid materials attached with different size of SiO₂ particles exhibited different reinforcing and toughening effect on the composites. With the increasing of the diameter of SiO₂ particles, the toughness and strength properties of the composites firstly improved and then decreased, and when the average diameter was 0.14 μm, the elongation reached the max.. Meanwhile, the fractured surfaces presented on SEM images were consistent with the results of the tensile tests, which further explained the hybrid materials increased the interfacial adhesion between the fillers and matrix, leading to significant improvement in mechanical properties. Moreover, the DSC curves demonstrated that Graphene/SiO₂ hybrid materials accelerated the curing process of epoxy resin due to the cross-link structure between fillers and matrix. Lastly, the crack propagation modes were built to clarify the synergy effect mechanism of reinforcing and toughening on nanoparticles/epoxy resin composites.     

Evaluating the Mechanical Behavior of Basalt Fibers/Epoxy Composites Containing Surface-modified CaCO<Subscript>3</Subscript> Nanoparticles

Polymer matrix composites (PMCs) owing to their outstanding properties such as high strength, low weight, high thermal stability and chemical resistance are broadly utilized in various industries. In the present work, the influence of silanized CaCO₃ (S-CaCO₃) with 3-aminopropyltrimethoxysilane (3-APTMS) coupling agent at different values (0, 1, 3 and 5 wt.% with respect to the matrix) on the mechanical behavior of basalt fibers (BF)/epoxy composites was examined. BF-reinforced composites were fabricated via hand lay-up technique. Experimental results from three-point bending and tensile tests showed that with the dispersion of 3 wt.% S-CaCO₃, flexural strength, flexural modulus, tensile strength and tensile modulus enhanced by 28 %, 35 %, 20 % and 30 %, respectively. Microscopic examinations revealed that the development of the mechanical properties of fibrous composites with the incorporation of modified CaCO₃ was related to enhancement in the load transfer between the nanocomposite matrix and BF as well as enhanced mechanical properties of the matrix part.     

Electrospun in-situ hybrid polyurethane/nano-TiO<Subscript>2</Subscript> as wound dressings

By combining the organic-inorganic hybridization, wet phase inversion, and electrospinning, novel electrospun polyurethane (PU) membranes with in-situ generated nano-TiO₂ were prepared, which satisfied the requirements of an ideal wound dressing. The morphology of the PU-TiO₂ mats and the cross sectional morphologies of the membranes were characterized by a scanning electron microscopy (SEM). The average diameter of the individual fibers obtained from the solutions was 341±12 nm. SEM micrographs with higher magnification further showed that the in-situ generated TiO₂ particles were well-separated and dispersed homogeneously in the membranes. The average sizes of TiO₂ particles were increased from 31 to 57 nm, with the increase of nano-TiO₂ concentration. The water vapor transmission rates (WVTRs) of the membranes were in the range of 373.55–3121.86 g/m²·d and decreased gradually with the increase of nano-TiO₂ concentration. The water absorption of various PU membranes was in the range of 210.90–397.98 % which was enough to prevent wound beds from exudate accumulation. Shake flask testing indicated that the PU membrane exhibited antibacterial efficiency against Pseudomonas aeruginosa (Ps. aeruginosa) and Staphylococcus aureus (S. aureus) due to in-situ generated of nano-TiO₂. These electrospun nanofibrous membranes also had no toxic effect and showed good and immediate adherence to L929 cells.     

Preparation and characterization of inner-pressure hollow fiber composite membrane via two-way coating technique for CO<Subscript>2</Subscript>/CH<Subscript>4</Subscript> separation

High-selectivity inner-pressure hollow fiber composite (HFC) membrane for CO₂/CH₄ separation was prepared through the Two-way coating (TWC) technique. The blends of poly(vinylamine) (PVAm)/polyvinyl alcohol (PVA) were coated onto porous hollow fiber polysulfone (PSF) ultrafiltration (UF) membrane with an effective membrane area of 0.4 m². The effects of fabrication parameters on the permselectivity of the resultant HFC membrane were investigated and the optimum preparation conditions were obtained as follows: coating time for 30 min and air blowing time for 30 min after the coating. The prepared HFC membrane showed the typical characteristic of fixed carrier membrane with a high selectivity of CO₂ and CH₄: the separation factor of CO₂/CH₄ (40 vol% CO₂ at 25 °C and 0.2 MPa) was 36.6 and the CO₂ permeability was 56.3 GPU. Field emission scanning electron microscopy (FESEM) images indicated that the HFC membrane prepared by TWC technique had a uniform coating layer along the whole hollow fiber. Membrane permselectivity showed almost no difference between different membrane sections. The HFC membrane showed a good stability during the continuous testing process of 540 h. And the HFC membrane preserved at 30 °C and 40 % humidity exhibited a good durability with a basically unchanged separation factor after 30 days.     

Effect of organic,inorganic and slow-release urea fertilisers on CH<Subscript>4</Subscript> and N<Subscript>2</Subscript>O emissions from rice paddy fields

Vietnam is one of the world’s top two rice exporting countries. However, rice cultivation is the primary source of agriculture’s greenhouse gas (GHG) emissions in Vietnam. In particular, strategies are required to reduce GHG emissions associated with the application of organic and inorganic fertilisers. The objective of this study was to assess the effects of various combinations of biochar (BIOC), compost (COMP) and slow-release urea (SRU) on methane (CH₄) and nitrous oxide (N₂O) emissions. In total, 1170 gas samples were collected from closed gas chambers in rice paddies at Thinh Long commune and Rang Dong farm in northern Vietnam between June and October 2014. The gas samples were analysed for CH₄-C and N₂O-N fluxes using gas chromatography. The application of BIOC alone resulted in the lowest CH₄ emissions (4.8–59 mg C m^?2 h^?1) and lowest N₂O emissions (0.15–0.26 µg N m^?2 h^?1). The combined application of nitrogen–phosphorus–potassium (NPK) + COMP emitted the highest CH₄ (14–72 mg C m^?2 h^?1), while ½NPK + BIOC emitted the highest N₂O (1.03 µg N m^?2 h^?1 in the TL commune), but it was the second lowest (0.495 µg N m^?2 h^?1) in the RD farm. Green urea and orange urea reduced N₂O emissions significantly (p < 0.05) compared to white urea, but no significant differences were observed with respect to CH₄ emissions. SRU fertilisers and BIOC alone measured the lowest greenhouse gas intensity, i.e. <2.5 and 3 kg CO₂ eq. kg^?1 rice grain, respectively. Based on these results, application of fertilisers in the form of BIOC and/or orange or green urea could be a viable option to reduce both CH₄ and N₂O emissions from rice paddy soils.     

The effect of floating vegetation on CH<Subscript>4</Subscript> and N<Subscript>2</Subscript>O emissions from subtropical paddy fields in China

Duckweed (Lemna minor), a floating macrophyte belonging to the Lemnaceae family, is commonly found in subtropical paddy fields. This plant rapidly takes up nutrients from water and forms dense floating mats over the water surface that may impact the biogeochemical processes and greenhouse gas production in paddy fields. In this study, we measured CH₄ and N₂O emissions from duckweed and non-duckweed plots in a subtropical paddy field in China during the period of rice growth using static chamber and gas chromatography methods. Our results showed that CH₄ emission rate ranged from 0.19 to 26.50 mg m^?2 h^?1 in the duckweed plots, and from 1.02 to 28.02 mg m^?2 h^?1 in the non-duckweed plots. The CH₄ emission peak occurred about 1 week earlier in the duckweed plots compared to the non-duckweed counterparts. The mean CH₄ emission rate in the duckweed plots (9.28 mg m^?2 h^?1) was significantly lower than that in non-duckweed plots (11.66 mg m^?2 h^?1) (p < 0.05), which might be attributed to the higher water and soil Eh in the former. N₂O emission rates varied between ?50.11 and 201.82 µg m^?2 h^?1, and between ?28.93 and 54.42 µg m^?2 h^?1 in the duckweed and non-duckweed plots, respectively. The average N₂O emission rate was significantly higher in the duckweed plots than in the non-duckweed plots (40.29 vs. 11.93 µg m^?2 h^?1) (p < 0.05). Our results suggest that the presence of duckweed will reduce CH₄ emission, but increase N₂O flux simultaneously. Taking into account the combined global warming potentials of CH₄ and N₂O, we found that growing duckweed could reduce the overall greenhouse effect of subtropical paddy fields by about 17 %.     

Macropores regulate CO<Subscript>2</Subscript> behavior in an andisol soil

Macropores resulting from soil pedogenesis, biological activity, and agricultural practices play important roles in soil water, chemical and gas transport; however, seldom studies focus on the effect of soil macropores on CO₂ behavior. In this study, a 150-day soil column incubation experiment was conducted to investigate the CO₂ behavior in a homogeneous soil column and a soil column with an artificial macropore, which have the same total porosity. The results showed that the cumulative CO₂ fluxes observed in the soil with a macropore (57.2 g m^?2) were higher than those in the homogeneous soil (52.7 g m^?2). The soil cumulative CO₂ fluxes measured using column incubation can fit the kinetic model, and a higher carbon mineralization rate in the soil with the macropore was found. The results of the incubation experiment also suggest that macropore increased the gas diffusivities, and thus decreased the CO₂ concentrations in the soil profile. This study proposed a simulation experiment and quantified the effect of macropore on soil CO₂ behavior, which could help to understand the mechanism of CO₂ emission from soil with macropores especially caused by agricultural practices.     

Polyacrylonitrile/electroconductive TiO<Subscript>2</Subscript> nanoparticles composite fibers <Emphasis Type="Italic">via</Emphasis> wet-spinning

For the first time, novel polyacrylonitrile (PAN)/electroconductive TiO₂ (EC-TiO₂) nanoparticles composite fibers have been successfully spun via wet-spinning. The composite fibers had uniform diameter and homogeneous surface. Moreover, at low content of EC-TiO₂ nanoparticles, the composite fibers realized a transition from an insulator to a conductor. This work has provided a simple and effective avenue for the production of PAN/EC-TiO₂ nanoparticles composite fibers that have great potential applications in the antistatic textiles.     

Electrospun poly(L-lactic)acid/nanoalumina (PLA/Al2O3) composite fiber mats with potential biomedical application — Investigation of cytotoxicity

PLA fibrous mats containing nanoalumina filler were fabricated by electrospinning method. The morphology of the mats was characterized by SEM, and TEM. In vitro biocompatibility of the electrospun fiber mats was also evaluated. Indirect cytotoxicity evaluation of the fiber mats with human skin fibroblasts revealed that the materials were non-toxic to living cells. The cells cultured on the fibrous mat exhibited normal cells shapes and were integrated well with surrounding fibers. The obtained results confirmed the potential for use of the electrosupun PLA/Al₂O₃ fiber mats for biomedical application.     

Modification and Characterization of Nano-TiO<Subscript>2</Subscript> for Efficient Fixation on Cotton Fibers

In this paper, a silane coupling agent, 3-aminopropyltriethoxysilane, was reacted with nano-TiO₂ to introduce amino group onto it which was then reacted with trichlorotriazine to obtain a dichlorotriazine functionalized nano-TiO₂ for the firm fixation of it on cotton fibers. The reaction process was monitored by the titration of primary and secondary amino groups, and the reaction conditions were optimized with orthogonal method accordingly. The dichlorotriazine functionalized nano-TiO₂ was reacted with cotton fabric by the nucleophile substitution reaction to afford nano-TiO₂ functionalized cotton fabric, the structure and surface morphology of the nano-TiO₂ finished cotton fibers were studied by FT-TR and SEM. In addition, the fixation duration of the nano-TiO₂ modified cotton was studied according to AATCC test method 61–2010. The results show that the washing fastness of the nano-TiO₂ is excellent.     

Polyaniline-doped TiO<Subscript>2</Subscript>/PLLA fibers with enhanced visible-light photocatalytic degradation performance

A simple and practical strategy has been developed for preparing polyaniline(PANi)-doped TiO₂/poly(l-lactide) (P@TiP-C) fibers by a combination of coaxial-electrospinning and in-situ polymerization. The TiO₂/PLLA composite fibers with TiO₂ located on the surface were fabricated by coaxial-electrospinning, with PLLA as the core phase and a dispersion of TiO₂ particles, a well-known photocatalyst, in the sheath phase. The aniline monomers were also located in the core phase and in-situ polymerized by ammonium persulfate (APS) after electrospinning. SEM images show that TiO₂ particles were located on the surface of PLLA fibers. Photocatalytic degradation tests show that the P@TiP-C fibers exhibit enhanced photocatalytic activity for degradation of methyl orange under visible light, likely due to the synergistic effect of PANi and TiO₂.     

Experimental study on dyeing technical PET yarns having different TiO<Subscript>2</Subscript> contents

TiO₂ contents in yarns can influence color yield so that dyeing quality of industrial poly ethylene terephthalate (PET) yarns can be improved through the adjustment of TiO₂ contents. To evaluate the dyeing performance of color yield, the chips which included the different TiO₂ contents of 330, 550, and 1,100 ppm respectively were used to produce the yarns of different TiO₂ content by a spin-draft machine. The physical and structural properties of the yarns were measured to investigate effect of the TiO₂ contents on them. Dye uptake and dyeing rate were also evaluated using a colorimeter to compare the yarns having different TiO₂ contents. The experimental results showed that there were no appreciable variation in physical and structural properties among the yarn samples and no difference were observed among the dyed fabric samples with regard to dyeing uptake and dyeing rate. However, the color yield of dyed fabrics increased as TiO₂ contents decreased in the yarns especially when the fabric samples were dyed to pale shade. The physical reasoning could be proposed on why the yarns having low TiO₂ contents appeared to have higher color yield after dyeing.