Investigation of changes in compressed moso bamboo (<Emphasis Type="Italic">Phyllostachys pubescens</Emphasis>) after hot-press molding

In this study, molding moso bamboo strips to a curved shape using hot-press molding operation was explored. Bamboo strips with different thickness and moisture content (MC) were subjected to press molding under 120–210 °C for different time. Changes in the chemical components of bamboo were analyzed by Fourier-transform infrared spectroscopy (FTIR). Effect of MC on thermal mechanical behavior of bamboo was investigated using dynamic mechanical analysis (DMA). Results showed that the influencing degree of four variables on compression and recovery ratios decreased as: temperature?>?time?>?thickness?>?MC. Compression ratio increased and recovery ratio decreased dramatically when pressing temperature exceeded 180 °C. FTIR analysis indicated that polysaccharide (especially hemicelluloses) underwent a progressive thermal degradation during compression at 180 and 210 °C for 40 min, whereas relative content of lignin increased. DMA results showed that bamboo samples with a higher MC had a lower storage modulus value, confirmed water had a plasticizing effect. The loss factor of bamboo with higher MC (12 and 16%) exhibited two major transitions centred around 100 °C (α₁) and 50 °C (α₂), respectively. The temperature of these α transitions kept almost unchanged as moisture level increased from 12 to 16%. These findings provide fundamental information for the future preparation of curved bamboo as profiled components in engineered products.     

Green color protection of bamboo culms using one-step alkali pretreatment-free process

This study evaluated the protection effectiveness of alcohol-borne reagents for the green color of ma bamboo (Dendrocalamus latiflorus Munro) and moso bamboo (Phyllostachys pubescens Mazel). The results show that the types and concentrations of alcohol-borne reagents, the kinds of solvent, and the conditions of treatment greatly affected the green color of these two bamboo species. Without alkali pretreatment, an excellent green color protection (a* = −14.5) was obtained when the ma bamboo culms were treated with 0.5% methanol-borne copper chloride (CuCl₂) at 60°C for 30 min. Similar results were also obtained when ma bamboo culms were treated with 0.5% methanol-borne copper nitrate [Cu(NO₃)₂] at 60°C for 2 h (a* = −13.5). For moso bamboo, an attractive green color in the bamboo culms was achieved by treating the specimens with 1% methanol-borne copper acetate [Cu(CH₃COO)₂] at 60°C for 30 min. The a* value of treated specimens was −13.3. In addition, results demonstrated that ultrasonic treatment was more effective on green color protection than conventional water bath treatment. When moso bamboo was treated with 1% copper acetate at 60°C in an ultrasonic bath for only 15 min, a remarkable green color with an a* value of −13.6 was obtained on the bamboo epidermis.     

Carbonization of bamboo and consecutive low temperature air activation

Raw moso bamboo (Phyllostachys pubescens) was examined to optimize the carbonization and the consecutive air activation procedure. Influence of sample size, nitrogen flow rate, heating rate and final temperature on the carbon yield and the pore structure was investigated for the raw bamboo. The short length cutting along bamboo trunk and the increase in heating rate to 40°C/min and nitrogen flow rate up to 500 ml/min was found to be advantageous for the carbonization of raw bamboo at 500°C, resulting in a surface area of 230 m²/g with a bamboo char yield of 25% on dry base. In the next step, effects of air treatment temperature, ash content and its composition on the pore development were studied for the prepared bamboo char in comparison with coconut shell char. Additional increase in surface area by 200 m²/g with 97% yield could be achieved conducting the 2-hour air treatment at 280°C for the bamboo char, whereas only a 100 m²/g rise in surface area was attained for the coconut shell char, partly due to the difference in K₂CO₃ content in the char.     

Environmentally benign methods for producing green culms of ma bamboo (<Emphasis Type="Italic">Dendrocalamus latiflorus</Emphasis>) and moso bamboo (<Emphasis Type="Italic">Phyllostachys pubescens</Emphasis>)

The objective of this study was to find an effective method for treating ma bamboo (Dendrocalamus latiflorus) and moso bamboo (Phyllostachys pubescens) using new water-based reagents containing copper. The effects of green-color protection using various treatments on bamboo culms were examined in this study. Two methods were used: heating in a water bath and ultrasonic dipping. The results revealed that excellent green-color protection (a* value of −6.2) was obtained when ma bamboo culms were treated with 0.25% ammoniacal copper quaternary compound-type B (ACQ-B) in a water bath at 100°C for 2 h. It was also found that the wettability of bamboo epidermis increasedsignificantly after pretreatment in a mixture of 1% KOH and surfactant in a water bath at 100°C for 30 min. Furthermore, pretreated moso bamboo culms exhibited excellent green-color protection after they were treated with 0.25% ACQ-B at 100°C for 2 h (a* value of −8.2). This novel treatment method definitely endows the bamboo culms with a fascinating green skin color and consequently could increase the economic value of bamboo products. No improvement in green-color protection was found when ultrasonic energy was added to the water bath at ambient temperature.     

Effects of osmopriming and hydropriming on vigour and germination of China aster (Callistephus chinensis (L.) Nees.) seeds

The aim of this research was to evaluate the effects of osmopriming and different hydropriming treatments on the vigour and germination of China aster (Callistephus chinensis) seeds. Seed vigour and germination tests were conducted at 10, 20 and 30°C in darkness for untreated, osmoprimed and hydroprimed seeds. The following parameters and categories of seeds and seedlings were evaluated: the mean germination time (MGT), T10, T50, U75–25, U90–10, the percentage of germinating seeds (Gmax), germination capacity, percentage of abnormal seedlings and dead seeds. The results showed that osmopriming accelerated seed germination to the largest extent and improved the uniformity of germination at 10 and 30°C. Among the hydropriming treatments the highest speed of germination was observed for seeds hydrated in 500 μL of water per 1 g of seeds for 48 h at 15°C. This treatment accelerated seed germination at 10°C compared with the control. Osmopriming increased seed germination capacity at 30°C. None of the applied hydropriming treatments improved this parameter.     

Optimal germination condition by sulfuric acid pretreatment to improve seed germination of Sabina vulgaris Ant.

Understanding the germination traits of plants is important not only for understanding natural regeneration processes but also for developing seedling production techniques for planting. Sabina vulgaris Ant. is a common species used for reforestation in semi-arid areas of the Mu-Us Desert, in Inner Mongolia, China, but its extremely low germination rate, both in situ and in vivo, is a bottleneck for seedling production. Sulfuric acid pretreatment was applied to improve germination, and the germination rate was compared for different soaking time (10, 30, 60, 90, and 120 min), different temperatures (10, 15, 20, 30, and 35°C) and under different lighting conditions (dark and light). Sulfuric acid treatment gave a high germination rate, reaching 60% at 30 days after sowing. However, the non-treated seeds produced no germination. The optimal treatment time in sulfuric acid was 120 min. Germination after sulfuric acid treatment increased at incubation temperatures from 10 to 30°C, but decreased at 35°C. Incubation at 25–30°C gave maximum germination of more than 50%. Light treatment had little effect on germination. Pretreatment with sulfuric acid improved water absorption by the embryo by creating cracks and cavities in the seed coat tissue. These results indicated that S. vulgaris seeds have physical dormancy caused by their hard seed coats, which prevents absorption of water into the embryo. A combination of pretreatment with sulfuric acid and incubation at 25–30°C was most effective in improving the germination of S. vulgaris seeds.     

Hygrothermal effect of bamboo by dynamic mechanical analysis

Dynamic properties of bamboo, Phyllostachys pubescens, with moisture content (MC) ranging from −130 to 130°C, were studied by dynamic mechanical analysis (DMA). The results showed that the hygrothermal effect on dynamic mechanical properties was negative. The storage modulus decreases with increasing temperature and MC, and glass transition temperature decreases with increasing MC. The glass transition temperature and tan delta of bamboo were 30.5°C, 0.02 and 10.61°C, 0.04, when MC was 10% and 34%, respectively. __________ Translated from Journal of Nanjing Forestry University (Natural Sciences Edition), 2006, 30(1): 65–68 [译自: 南京林业大学学报(自然科学版), 2006, 30(1): 65–68]     

Temperature-dependent functional response of two aphid parasitoids, Aphidius colemani and Aphidius matricariae (Hymenoptera: Aphidiidae), on the cotton aphid

The functional response of two aphid parasitoids, Aphidius colemani Viereck and Aphidius matricariae (Haliday) (Hymenoptera: Aphidiidae), on the cotton aphid, Aphis gossypii Glover (Homoptera: Aphididae), was examined. Five constant temperatures (10, 15, 20, 25, and 30°C) and six host densities (2, 4, 8, 16, 32, and 64) were used during a 24-h period. At each temperature, 2–64 third-instar nymphs of A. gossypii were exposed to individual wasp mating pairs. A type II functional response model for both parasitoid wasps was fit separately for each temperature. The results showed that instantaneous attack rate (a) in A. colemani increased linearly as the temperature increases from 10 to 30°C, but in A. matricariae, (a) increased almost linearly with temperature to reach a maximum at 25°C, and then decreased at 30°C, displaying an asymmetrical dome-shaped pattern. The highest instantaneous attack rate for A. colemani and A. matricariae were calculated 0.940 ± 0.144 day⁻¹ at 30°C and 0.687 ± 0.157 day⁻¹ at 25°C, respectively. Handling time (T _h) for A. colemani was inversely proportional to temperature and ranged from 0.093 ± 0.026 day at 10°C to 0.032 ± 0.004 day at 30°C, but in A. matricariae, (T _h) was between 0.078 ± 0.015 day at 10°C and 0.036 ± 0.014 day at 20°C. A. colemani achieved higher parasitism rate than A. matricariae at higher temperatures. This observation suggests that A. colemani maybe more effective for biological control of the cotton aphid during warmer periods.     

Effect of seed treatment for laboratory germination of Albizia chinensis

Seeds of Albizia chinensis(Osb.) Merr. in addition to water were also treated with different treatments by incubating in ethyl alcohol, acetone, and petroleum ether at room temperature for different du...     

Study of Cr(VI) adsorption onto nitrogen-containing activated carbon preparation from bamboo processing residues

Nitrogen-containing bamboo charcoals were prepared using bamboo processing residues, and modified by melamine or urea. The iodine value of the products we obtained was analyzed, and two samples were chosen for the Cr(VI) adsorption. The experimental results show that under the KOH and carbon ratio of 3:1 (w₁/w₂), activation temperature 800 °C and activation time 1 h, the activated carbons modified by melamine boasted the iodine value of 1144 mg/g and the activated carbons modified by urea boasted the iodine value of 1263 mg/g. In addition, the equilibrium adsorption capacity is 95.3 mg/g for the activated carbons modified by melamine with the adsorbent dosage of 1.0 g/L at an initial pH 2 in the presence of 100 mg/L K₂Cr₂O₇ at 30 °C for 180 min and it is 94.2 mg/g for the activated carbons modified by urea in the same reaction condition. The pseudo-second-order kinetic model can better reflect the two kinds of nitrogen-containing activated carbons adsorption kinetic process of Cr(VI). The adsorption process conforms to the Langmuir model, indicating that the process is single molecular layer adsorption.     

Carbonization mechanism of bamboo（phyllostachys） by means of Fourier Transform Infrared and elemental analysis

Bamboo was carbonized at different temperatures ranging from 200℃ to 600℃.The dependence of the change of hemicellulose,cellulose,and lignin on the temperature was investigated by means of elemental analysis and Fourier Transform Infrared (FTIR) spectra of the residual solid products.The results showed:(1)Below 200℃,hemicellulose in bamboo wasdecomposed and a large amount of hydroxyl groups are dislocated from hemicellulose and cellulose,accompanied by the evolution of water to escape.(2)200℃-250℃,cellulose in bamboo was brastically decomposed whereas the net structure of lignin keep stable,with the except of the dislocation of methoxyl groups from lignin.(3)250℃-400℃,the net structure of lignin collapse,up to 400℃,followed by that the more position in aryl groups are substituted.(4)For bamboo carbonization,the aromatization of residual carbon has approximately completed at the temperature as high as 600℃.But the fusion of aromatic rings possibly does not occur.     

Changes in bamboo fiber subjected to different chemical treatments and freeze-drying as measured by nanoindentation

The effects of chemical treatments (H₂O₂ + CH₃COOH, acidified NaClO₂, and NaOH) and freeze-drying on bamboo fibers were studied at a submicron level, to characterize chemical and mechanical changes to the secondary cell wall. Specifically, a field emission environmental scanning electron microscope (FE-ESEM) and imaging fourier transform infrared spectroscopy (FTIR) were used to demonstrate degradation in morphology and molecular structure, and nanoindentation was used to track changes in micromechanical properties. The results showed that cellular structures after chemical treatments clearly displayed wrinkles, pores, and microfibrils. The decreased bands at 1508 cm^-1 and 1426 cm^?1 showed that lignin was degraded on treatment of H₂O₂ + CH₃COOH and acidified NaClO₂, which directly resulted in a decrease in hardness (H) in the secondary cell wall for treated fibers. In addition, a diminishing peak at 1733 cm^?1 caused by NaOH solution indicated that hemicellulose was seriously degraded. It resulted in a decreased modulus (E _r) by 13.71 % in bamboo fibers, while no obvious reduction was observed in the first two steps.     

冷湿层积法对印度冷杉(Abies pindrow)和长叶云杉(Picea smithiana）种子萌发的影响

研究赤霉素(GA3),冷湿和温度 对五个种源的印度冷杉(Abies pindrow)和长叶云杉(Picea smithiana)种子萌发的影响.种子被浸泡在GA3 (10 mg(L-1)中24小时,然后在3(5(C温度的条件下冷藏15天.设计4个温度(10(C, 15(C, 20(C 和 25(C)条件来促进种子的萌发.结果表明,浸泡和冷湿处理明显增加种子的萌发率.在10 (C时种子的萌发率最高.总体结果表明,种子被浸泡在GA3 (10 mg(L-1)中24小时,冷湿藏15天,可以有效地促进印度冷杉和长叶云杉的种子萌发.统计数据表明,浸泡处理、温度和种源以及与温度的相互作用都对种子的萌发有明显的影响.     

Compressive deformation of wood impregnated with low molecular weight phenol formaldehyde (PF) resin V: effects of steam pretreatment

This study evaluated the potential of steam pre-treatment for making highly compressed phenol-formaldehyde (PF) resin-impregnated wood at a low pressing pressure. Sawn veneers of Japanese cedar (Cryptomeria japonica) were first subjected to saturated steam at different steaming temperatures (140°-200°C), followed by impregnation with a 20% low molecular weight PF resin aqueous solution resulting in a weight gain of around 50%-55%. Four oven-dried treated veneers were laminated and compressed up to a pressing pressure of 1 MPa at a pressing temperature of 150°C and pressing speed of 5 mm/min, and the pressure was held for 30 min. Steam treatment, causing partial hydrolysis of hemicellulose, accelerated the compressibility of Japanese cedar in the PF resin-swollen condition. As a consequence, a discernible increment in density was achieved at a pressing pressure of 1 MPa due to steam pretreatment between 140° and 200°C for 10 min. It was also found that even a short steaming time such as 2 min at 160°C is sufficient for obtaining appreciable compression of PF resin-impregnated wood. The density, Young’s modulus, and bending strength of steam-treated (200°C for 10 min) PF resin-impregnated wood composite reached 1.09 g/cm³, 20 GPa, and 207MPa, respectively. In contrast, the values of untreated PF resin-impregnated wood composite were 0.87 g/cm³, 13 GPa, and 170MPa, respectively.     

Effects of freeze-thaw on soil nitrogen and phosphorus availability at the Keerqin Sandy Lands, China

A laboratory simulated freeze-thaw was conducted to determine the effects of freeze-thaw on soil nutrient availability in temperate semi-arid regions. Soil samples were collected from sandy soils （0-20 cm） of three typical ecosystems （grassland, Mongolian pine plantation and poplar plantation） in southeastern Keerqin Sandy Lands of China and subjected to freeze-thaw treatment （-12℃ for 10 days, then r 20℃ for 10 days） or incubated at constant temperature （20℃ for 20 days）. Concentrations of the soil NO3^--N, NH4^＋-N, NaHCO3 extractable inorganic P （LPi） and microbial biomass P （MBP） were determined on three occasions： at the start of the incubation, immediate post-thawing and at the 10th day post-thawing. The results showed that soil net nitrification and N mineralization rates at three sites were negatively affected by freeze-thaw treatment, and decreased by 50%-85% as compared to the control, of which the greatest decline occurred in the soil collected from poplar plantation. In contrast, the concentration of soil NH4^＋-N, NaHCO3 extractable inorganic P （LPi） and microbial biomass P were insignificantly influenced by freeze-thaw except that LPi and NH4^＋-N showed a slight increase immediate post-thawing. The effects of freeze-thaw on soil N transformation were related to soil biological processes and the relatively constant available P was ascribed to severe soil aridity.     

Feasibility of supercritical carbon dioxide as a carrier solvent for preservative treatment of wood-based composites

 Supercritical carbon dioxide (SC-CO₂) was tested for its potential as a carrier solvent for preservative treatment of solid wood and wood-based composites. A preliminary trial showed that the treatability of solid wood varied with its original permeability and that the SC-CO₂ treatment was not promising for refractory timber species such a Larix leptolepis Gordon. In contrast, 3-iodo-2-propynyl butylcarbamate (IPBC)/SC-CO₂ treatment resulted in enhanced decay resistance without any detrimental physical or cosmetic damage in all structural-use wood-based composites tested: medium density fiberboard, hardwood plywood, softwood plywood, particleboard, and oriented strand board (OSB). Further trials under various treatment conditions [25°C/7.85 MPa (80 kgf/cm²), 35°C/7.85 MPa, 45°C/7.85 MPa, 35°C/11.77 MPa (120 kgf/cm²), and 45°C/11.77 MPa] indicated that although small changes in the weight and thickness of the treated materials were noted the strength properties were not adversely affected, except for a few cases of softwood plywood and oriented strand board. The results of this study clearly indicated that the treatment condition allowed SC-CO₂ to transport IPBC into wood-based composites, and the optimum treatment condition seemed to vary with the type of wood-based composite. Received: October 24, 2001 / Accepted: February 15, 2002 Part of this work was presented at the 51st Annual Meeting of the Japan Wood Research Society, Tokyo, April 2001; and the 32nd Annual Meeting of the International Research Group on Wood Preservation, Nara, May 2001 Correspondence to:M. Muin     

Determining suitability of thermal development models to estimate temperature parameters for embryonic development of <Emphasis Type="Italic">Sitona lepidus</Emphasis> Gyll. (Coleoptera: Curculionidae)

The clover root weevil, Sitona lepidus Gyll. is a pest of clovers (Trifolium spp.), particularly white clover (T. repens). Larva feeding severely impairs the capacity of white clover to fix atmospheric nitrogen, by attacking the nitrogen-fixing root nodules. Development of the egg stage was studied at six different constant temperatures ranging from 9 to 30°C to improve the basis for phenological forecasts. Development occurred over the entire range of temperatures, although hatching percentage at 30°C was only 24.4% compared to 90.1% at 28.5°C. Developmental time decreased with increase in temperature from 9 to 28.5°C but increased markedly at 30°C. At 28.5°C, the embryo development period was the shortest (10.35 days); whereas at 9°C, this parameter was the longest (55.08 days). Using linear regression, the lower threshold temperature was calculated 4.38°C and the thermal constant was 236.45 degree-days. The relationship between constant temperature and developmental rate was evaluated using nine models. The suitability of the models was evaluated based on eight indicators (R ², RSS, R _adj², AIC, BIC, AICC, W _j , and Z _i ). Of the nonlinear models, the Logan-6, Sharpe and DeMichele, and Lactin models were the most accurate at calculating t _opt of 27, 27.50, and 28°C, respectively. The results suggest that of the three models (Lactin, Briere, and Hilbert and Logan), that estimated critical temperatures, (t _min, t _opt, and t _max), Lactin gave the most suitable fit of data. This response of S. lepidus to temperature can be used for developing phonological models to predict the timing of egg hatch which are important for management programs targeting the weevil.     

CaCO<Subscript>3</Subscript> in situ treated bamboo pulp fiber reinforced composites obtained by vacuum-assisted resin infusion

The aim of this study is to investigate the properties of CaCO₃ in situ treated bamboo pulp fiber (BPF) composites that have been filled with epoxy resin by means of vacuum-assisted resin infusion (VARI). Un-treated and treated BPF were processed at a pressure of 0.24 MPa into BPF preforms. VARI was used to infuse epoxy resin through the BPF preforms to make BPF composites. The flexural properties, impact property, and thermal properties of the BPF composites were analyzed. CaCO₃ with the loading of 30 wt% affects the performance of the composites. The flexural strength did not decrease and modulus of the treated BPF composites increased by 9.38%, while the impact strength decreased by 50.98%, compared to the control sample. Dynamic mechanical analysis revealed the maximum elastic moduli of the treated specimens increased by 1.19 times in the temperature range of ?20 to 120 °C. The thermal decomposition temperature of the composites was influenced by the effect of the crystal field and size effect of CaCO₃.     

Biological characteristics and life tables of Neoseiulus umbraticus Chant (Acari, Phytoseiidae) at three constant temperatures

The development time, survival and fecundity of the generalist predatory mite, Neoseiulus umbraticus Chant, were determined at 20, 25, and 30?°C and 65?±?10?% RH. N. umbraticus females completed development in 9.7, 8.0 and 5.9 days, respectively, using a diet of all life stages of Tetranychus cinnabarinus Boisduval. Total developmental times of males were relatively shorter at 25 and 30?°C than at 20?°C. In general, preoviposition, oviposition, and postoviposition periods of N. umbraticus shortened as temperature increased. The longest survival rate of N. umbraticus of 80.5 days occurred at 20?°C, followed by 67.0 and 57.6 days at 25 and 30?°C, respectively. Mated females laid an average 0.9, 1.3 and 1.4 eggs per female per day and 33.1, 44.0 and 43.6 eggs over their entire lives at 20, 25 and 30?°C, respectively. The sex ratios of this species were 0.57, 0.57 and 0.54 female (female+male) at 20, 25 and 30?°C, respectively. The intrinsic rate of increase (r_m) became greater with rising temperatures from 0.123 at 20?°C to 0.180 at 30?°C. The net reproduction rate (R_o) was highest at 25?°C (25.0 females/female) and lowest at 20?°C (18.8 females/female), while T_o decreased with increasing temperatures, from 23.8 days at 20?°C to 17.5 days at 30?°C.