Evaluation of an osteoconductive resorbable calcium phosphate cement and polymethylmethacrylate for augmentation of orthopedic screws in the pelvis of canine cadavers

OBJECTIVE: To evaluate the effect of an osteoconductive resorbable calcium phosphate cement (CPC) on the holding power of bone screws in canine pelvises and to compare the effect with that for polymethylmethacrylate (PMMA). SAMPLE POPULATION: 35 pelvises obtained from canine cadavers. PROCEDURE: Each pelvis was sectioned longitudinally. Within each pair of hemipelvises, one 4.0-mm cancellous screw was placed in the sacroiliac (SI) region and another in the iliac body. Similar regions on the contralateral-matched hemipelvis were assigned 1 of 3 augmentation techniques (CPC-augmented 4.0-mm cancellous screws, PMMA-augmented 4.0-mm cancellous screws, and CPC-augmented 3.5-mm cortical screws). Pullout force was compared between matched screws and between treatment groups prior to examination of cross sections for evaluation of cement filling and noncortical bone-to-cortical bone ratio. RESULTS: CPC and PMMA augmentation significantly increased pullout force of 4.0-mm screws inserted in the SI region by 19.5% and 33.2%, respectively, and CPC augmentation significantly increased pullout force of 4.0-mm cancellous screws inserted in the iliac body by 21.2%. There was no difference in the mean percentage augmentation between treatment groups at either location. Cement filling was superior in noncortical bone, compared with filling for cortical bone. Noncortical bone-to-cortical bone ratio was significantly greater in the sacrum (6.1:1) than the ilium (1.3:1). CONCLUSIONS AND CLINICAL RELEVANCE: CPC and PMMA improve the ex vivo holding strength of 4.0-mm cancellous screws in the SI and iliac body regions and SI region, respectively. Cement augmentation may be more effective in areas with greater noncortical bone-to-cortical bone ratios.     

In Vitro Pullout Strength of Screws Inserted in Adult Equine Third Metacarpal Bone After Overdrilling a 4.5-mm Threaded Insertion Hole

Objective—To determine and compare the in vitro pullout strength of 5.5-mm cortical versus 6.5-mm cancellous bone screws inserted in the diaphysis and metaphysis of adult equine third metacarpal (MCIII) bones, in threaded 4.5-mm cortical bone screw insertion holes that were then overdrilled with a 4.5-mm drill bit to provide information relevant to the selection of a replacement screw if a 4.5-mm cortical screw is stripped. Study Design—In vitro pullout tests of 5.5-mm cortical and 6.5-mm cancellous screws in equine MCIII bones. Sample Population—Two independent cadaver studies each consisting of 14 adult equine MCIII bones. Methods—Two 4.5-mm cortical screws were placed either in the middiaphysis (study 1) or distal metaphysis (study 2) of MCIII bones. The holes were then overdrilled with a 4.5-mm drill bit and had either a 5.5-mm cortical or a 6.5-mm cancellous screw inserted; screw pullout tests were performed at a rate of 0.04 mm/second until screw or bone failure occurred. Results—In diaphyseal bone, the screws failed in all tests. Tensile breaking strength for 5.5-mm cortical screws (997.5 ± 49.3 kg) and 6.5-mm cancellous screws (931.6 ± 19.5 kg) was not significantly different. In metaphyseal bone, the bone failed in all tests. The holding power for 6.5-mm cancellous screws (39.1 ± 4.9 kg/mm) was significantly greater than 5.5-mm cortical screws (23.5 ± 3.5 kg/mm) in the metaphysis. There was no difference in the tensile breaking strength of screws in the diaphysis between proximal and distal screw holes; however, the holding power was significantly greater in the distal, compared with the proximal, metaphyseal holes. Conclusions—Although tensile breaking strength was not different between 5.5-mm cortical and 6.5-mm cancellous screws in middiaphyseal cortical bone, holding power of 6.5-mm cancellous screws was greater than 5.5-mm cortical screws in metaphyseal bone of adult horses. Clinical Relevance—If a 4.5-mm cortical bone screw strips in MCIII diaphyseal bone of adult horses, either a 5.5-mm cortical or 6.5-mm cancellous screw, however, would have equivalent pullout strengths. A 6.5-mm cancellous screw, however, would provide greater holding power than a 5.5-mm cortical screw in metaphyseal bone.     

Holding Power of Orthopedic Screws in Equine Third Metacarpal and Metatarsal Bones: Part II. Adult Horse Bone

Comparison was made of the holding power of 5.5 and 4.5 mm cortical orthopedic screws inserted into third metacarpal and metatarsal cadaver bones from 3- and 8-year-old horses. The tensile strength of these screws was tested mechanically. In nine comparative trials of these screws, 5.5 mm screws pulled out of bone in five trials at an average of 116.0 kg tensile force and broke in four trials at an average of 1383.2 kg. A 4.5 mm screw pulled out of bone at 834.5 kg in one trial, and screws broke at an average of 849.2 kg in eight trials. The larger 5.5 mm screw required a significantly greater (p = 0.022) pullout force than the mean force at 4.5 mm screw breakage. Fixation failure was due to screw breakage or bone shear, with 5.5 mm screws occasionally creating bone fragmentation during pullout. The average tensile breaking strengths of the 5.5 mm screws (1391.4 kg) and 4.5 mm screws (832.7 kg) determined mechanically were similar to forces at screw breakage during pullout testing in bone. Since the 5.5 mm screws have greater holding power and tensile strength than 4.5 mm screws, the use of the 5.5 mm screw in fracture repair in adult horses is recommended.     

An in vitro biomechanical comparison of the insertion variables and pullout mechanical properties of ao 6.5-mm standard cancellous and 7.3-mm self-tapping, cannulated bone screws in foal femoral bone

OBJECTIVE: To compare screw insertion variables and pullout mechanical properties between AO 6.5-mm cancellous and 7.3-mm cannulated bone screws in foal femoral bone. STUDY DESIGN: A paired, in vitro mechanical study. SAMPLE POPULATION: Seven pairs of femora from immature (1-7 months) foals. METHODS: The 6.5 cancellous and 7.3-mm cannulated screws were inserted at standardized proximal and distal metaphyseal, and mid-diaphyseal locations. Insertion torque, force, and time to drill, tap (6.5-mm cancellous), guide wire insertion (7.3-mm cannulated), and screw insertion were measured. Screw pullout properties (yield and failure load, displacement, and energy, and stiffness) were determined from mechanical tests. The effects of screw type and location on insertion variables and pullout properties were assessed with repeated measures ANOVA. Pairwise comparisons were examined with post hoc contrasts. Significance was set at P<.05 for all comparisons. RESULTS: Insertion torques for the 7.3-mm cannulated screws were significantly greater than for the 6.5-mm tap, but significantly lower than for the 6.5-mm cancellous screws. Total screw insertion times were similar. Pullout properties of both screws were similar at each femoral location. The holding power of both screws was significantly greater in the mid-diaphysis than in either metaphyseal location. Pullout failure occurred by bone shearing at the bone-screw interface in all specimens. CONCLUSIONS: The 6.5-mm cancellous and 7.3-mm cannulated screws vary in insertion properties, but have similar pullout properties in the mid-diaphysis, proximal, and distal metaphysis of foal femora. Both screw types have greater holding power at the mid-diaphyseal location compared with metaphyseal locations. Based on overall similar holding powers of 6.5-mm cancellous and 7.3-mm cannulated screws, it is unlikely that increasing the screw diameter beyond 6.5 mm will provide increased holding power in foal femoral bone. CLINICAL RELEVANCE: Use of the 7.3-mm cannulated screw should be considered for foal femoral fracture repair when greater accuracy is needed, or when bone threads for the 6.5-mm cancellous screw have been stripped.     

In vitro evaluation of screws and suture anchors in metaphyseal bone of the canine tibia

OBJECTIVE: To compare ease of insertion, load to failure, and mode of failure of cortical and cancellous screws, BoneBiter, IMEX, and TwinFix suture anchors in canine metaphyseal tibial bone. STUDY DESIGN: Experimental biomechanical study. ANIMALS: Canine cadaveric tibias. METHODS: One investigator inserted all anchors and subjectively evaluated ease of placement. Anchor systems were loaded to failure along axis of insertion with audio-video recording to determine failure mode. RESULTS: BoneBiter was the most difficult anchor to insert successfully. Mean+/-SD loads to failure were cancellous screw (711+/-193 N), IMEX 4.7 mm 18 g wire (661+/-163 N), IMEX 4.0 mm 18 g wire (661+/-165 N), cortical screw (635+/-184 N), BoneBiter #5 Kevlar suture (393+/- 109 N), and TwinFix 5.0 mm #2 polyester (267+/-73 N). No significant differences were noted among the cortical screw, cancellous screw, IMEX 4.7 and 4.0 mm, all of which were significantly (P<.001) greater than BoneBiter and TwinFix . Failure modes were pullout of bone, suture-wire breakage, eyelet breakage, or no failure to 1000 N: screws (18,0,0,2), IMEX (18,1,1,0), BoneBiter (2,8,0,0), and TwinFix (0,10,0,0). CONCLUSIONS: Fixation devices were user friendly, with the exception of BoneBiter. Mode of failure is dependent on suture material and anchor design. Cortical and cancellous screws, and IMEX anchors with 18 g wire have significantly greater load to failure compared with BoneBiter and TwinFix suture anchors. CLINICAL RELEVANCE: Based on load to failure, ease of use, design characteristics, and cost, IMEX anchors may have advantages over other comparable soft tissue fixation devices.     

Effect of laser shock peening on fatigue life and surface characteristics of stainless steel cortical bone screws

OBJECTIVE: To investigate the effect of laser shock peening on the fatigue life and surface characteristics of 3.5-mm-diameter cortical bone screws. SAMPLE POPULATION: 32 stainless steel, 3.5-mm-diameter cortical bone screws. PROCEDURE: Screws were randomly assigned to an untreated control group or 2 power-density treatment groups, 6 gigawatts (GW)/cm2 and 8.5 GW/cm2, for laser shock peening. Number of cycles to failure and findings on scanning electron microscopy-assisted morphometric evaluation, including the mode of failure, surface debris, surface damage, and thread deformation, were compared between control and treated screws. RESULTS: The 6 GW/cm2 treated screws had a significant (11%) improvement in fatigue life, compared with untreated control screws. The 8.5 GW/cm2 treated screws had a significant (20%) decrease in fatigue life, compared with control screws. A mild but significant increase in thread deformation was evident in all treated screws, compared with control screws. The 8.5 GW/cm2 treated screws had significantly more surface irregularities (elevations and pits), compared with control or 6 GW/cm2 treated screws. CONCLUSION AND CLINICAL RELEVANCE: A modest positive increase in fatigue strength was produced by this design of laser shock peening on the midshaft of cortical bone screws. High laser shock peening power densities were detrimental, decreasing screw fatigue strength probably resulting from structural damage. Greater fatigue life of cortical bone screws can be generated with laser shock peening and could reduce screw breakage as a cause of implant failure; however, future studies will be necessary to address biocompatibility, alternative cleaning techniques, alterations in screw strength and pullout characteristics, and effects on susceptibility to corrosion.     

Increased sacral screw purchase minimizes screw loosening in canine triple pelvic osteotomy

OBJECTIVE: To determine if screw loosening in triple pelvic osteotomies (TPO) is minimized when screws cranial to the ilial osteotomy had maximal sacral purchase. STUDY DESIGN: Prospective study. ANIMALS: Forty-six dogs with decreased acetabular coverage of the femoral head and minimal degenerative joint changes. METHODS: TPOs were performed where screws cranial to the ilial osteotomy were inserted to maximally engage sacral bone. Data collected were: use of ilial and ischial cerclage wire, screw length, ventrodorsal radiographic sacral width (most caudal aspect), pelvic canal diameter, and sacral penetration of the 3 cranial screws. On all subsequent radiographs, changes in screw position, pelvic canal diameter, and sacral purchase were noted. RESULTS: For 69 TPOs, 414 screws were used. Mean radiographic cranial screw length was 34.54 mm. Combined sacral depth of all 3 screws was 93.3% of sacral width. All osteotomies healed uneventfully. Twenty-four screws (6%) loosened with 12 being in the most cranial positions. Use of ischial or ilial cerclage wires did not statistically influence screw loosening. Pelvic diameter decreased by a mean of 7.79% from postoperative radiographs to the last radiographic recheck. CONCLUSIONS: By sufficiently engaging the sacrum with screws cranial to the ilial osteotomy, implant failures can be avoided and screw loosening minimized when a 6-hole TPO plate is used. CLINICAL RELEVANCE: To minimize screw-loosening in TPO, screws inserted cranial to the ilial osteotomy should be inserted to maximum sacral depth without penetrating the vertebral canal.     

Effect of bone diameter and eccentric loading on fatigue life of cortical screws used with interlocking nails

OBJECTIVE: To test the effects of bone diameter and eccentric loading on fatigue life of 2.7-mm-diameter cortical bone screws used for locking a 6-mm-diameter interlocking nail. SAMPLE POPULATION: Eighteen 2.7-mm-diameter cortical bone screws. PROCEDURE: A simulated bone model with aluminum tubing and a 6-mm-diameter interlocking nail was used to load screws in cyclic 3-point bending. Group 1 included 6 screws that were centrally loaded within 19-mm-diameter aluminum tubing. Group 2 included 6 screws that were centrally loaded within 31.8-mm-diameter aluminum tubing. Group 3 included 6 screws that were eccentrically loaded (5.5 mm from center) within 31.8-mm-diameter aluminum tubing. The number of cycles until screw failure and the mode of failure were recorded. RESULTS: An increase in the diameter of the aluminum tubing from 19 to 31.8 mm resulted in a significant decrease in the number of cycles to failure (mean +/- SD, 761,215 +/- 239,853 to 16,941 +/- 2,829 cycles, respectively). Within 31.8-mm tubing, the number of cycles of failure of eccentrically loaded screws (43,068 +/- 14,073 cycles) was significantly greater than that of centrally loaded screws (16,941 +/- 2,829 cycles). CONCLUSIONS AND CLINICAL RELEVANCE: Within a bone, locking screws are subjected to different loading conditions depending on location (diaphyseal vs metaphyseal). The fatigue life of a locking screw centrally loaded in the metaphyseal region of bone may be shorter than in the diaphysis. Eccentric loading of the locking screw in the metaphysis may help to improve its fatigue life.     

Comparison of insertion time and pullout strength between self-tapping and non-self-tapping AO 4.5-mm cortical bone screws in adult equine third metacarpal bone

OBJECTIVE: To compare screw insertion characteristics and pullout mechanical properties between self-tapping (ST) and non-self-tapping (NST) AO 4.5-mm cortical bone screws in adult equine third metacarpal bone (MC3). STUDY DESIGN: In vitro biomechanical experiment. ANIMALS OR SAMPLE POPULATION: Seven pairs of adult equine MC3. METHODS: Bicortical holes were drilled transversely in proximal metaphyseal, diaphyseal, and distal metaphyseal locations of paired MC3. NST screws were inserted in pre-tapped holes in 3 sites of one bone pair, and ST screws were inserted in non-tapped holes of contralateral MC3. Tapping and screw insertion times and maximum torques were measured. Screw pullout mechanical properties were determined. RESULTS: Screw insertion time was longer for ST screws. Total time for tapping and insertion (total insertion time) was over twice as long for NST screws. Statistically significant differences were not observed between screws for any pullout mechanical property. From pullout tests, diaphyseal locations had significantly stiffer and stronger structure than metaphyseal locations. Pullout failure more commonly occurred because of screw breakage than bone failure. Bone failure and bone comminution were more commonly associated with ST screws. Bone failure sites had pullout failure loads that were 90% of screw failure sites. CONCLUSIONS: NST and ST 4.5-mm-diameter cortical bone screws have similar pullout mechanical properties from adult equine MC3. ST screws require less than half the total insertion time of NST screws. CLINICAL RELEVANCE: Use of ST 4.5-mm-diameter cortical bone screws should be considered for repair of adult equine MC3 fractures; however, bone failures at screw sites should be monitored.     

A Biomechanical Comparison of 7-Hole 3.5 mm Broad and 5-Hole 4.5 mm Narrow Dynamic Compression Plates

Seven-hole 3.5 mm broad and 5-hole 4.5 mm narrow dynamic compression plates were applied to paired canine cadaveric tibias in a stable fracture model. Paired tibias were tested to acute failure in rotation and four-point bending, and to fatigue failure in four-point bending. Resistance to screw pullout was measured for three 3.5 mm cortical screws and two 4.5 mm cortical screws inserted in the configurations of the bone plates. All plate-bone systems failed by fracture of the bone through a screw hole. The 3.5 mm plate-bone system was stronger in acute failure in rotation and in four-point bending. There was no difference in stiffness, and no difference in the number of cycles to failure in fatigue testing. Three 3.5 mm screws had greater resistance to pullout than two 4.5 mm screws. Results indicate that the 7-hole 3.5 mm broad dynamic compression plate has a biomechanical advantage over the 5-hole 4.5 mm narrow dynamic compression plate.     

A Comparison of the Synthes 4.5-mm Cannulated Screw and the Synthes 4.5-mm Standard Cortex Screw Systems in Equine Bone

Objective —To determine risk of failure of the Synthes 4.5-mm cannulated screw system instrumentation in equine bone and to compare its application with the Synthes 4.5-mm standard cortex screw system.
Study Design —The maximum insertion torque of the cannulated and standard cortex screw systems were compared with the ultimate torsional strengths of the equipment. Pullout strength and ultimate tensile load of cannulated and standard cortex screws were also determined.
Sample Population—Paired equine cadaver third metacarpal and third carpal bones.
Methods —Maximum insertion torque and ultimate torsional strengths were determined by using an axial-torsional, servohydraulic materials testing system and a hand-held torquometer. Pullout tests were performed by using a servohydraulic materials testing system.
Results —Maximum insertion torque of all cannulated instrumentation was less than ultimate torsional strength at all locations ( P < .05). Maximum insertion torques of cannulated taps and screws were greater than for standard taps and screws in the third carpal bone ( P < .002). Pullout strength of the cannulated screws was less than the standard cortex screws at all sites ( P < .001). Cannulated screws broke before bone failure in all but one bone specimen. Conclusions—The risk of cannulated instrument or screw failure during insertion into bone is theoretically low. The relatively low pullout strength of the cannulated screws implies that the interfragmentary compression achievable is likely to be less than with standard cortex screws. Clinical Relevance—The relatively low pullout strength of the cannulated screw suggests that its risk of failure during fracture repair is greater than with the standard cortex screw.     

The biomechanical properties of the feline femur

The purpose of this study was to determine the biomechanical properties of feline long bone by testing cadaver bone from mature cats in compression, three-point bending, notch sensitivity and screw pull-out strength. The determination of these properties is of clinical relevance with regard to the forces resulting in long bone fractures in cats as well as the behaviour and failure mode of surgical implants utilized for fracture stabilization and repair in the cat. Cadaveric cat femurs were tested in compression, three-point bending and in three-point bending after the addition of a 2.0 mm screw hole. Cortical screws, 2.7 mm in diameter, were inserted in cadaveric cat femur samples for screw pull-out testing. The mean maximum load to failure of mid diaphyseal feline femurs tested in compression was 4201+/-1218 N. Statistical analysis of the parameter of maximum load tested in compression revealed a statistical difference between sides (p=0.02), but not location (p=0.07), or location by side (p=0.12). The maximum strength of mid diaphyseal feline femurs tested in compression was 110.6+/-26.6 MPa. The modulus of elasticity of mid-diaphyseal cat femurs tested in compression was determined to be 5.004+/-0.970 GPa. The mean maximum load to failure of feline femurs tested in three-point bending was 443+/-98 N. The mean maximum load to failure of feline femurs tested in three-point bending after a 2.0 mm diameter hole was drilled in the mid-diaphyseal region of each sample through both cortices was 471+/-52 N. The mean maximum load required for screw pull-out of 2.7 mm cortical screws placed in feline femurs tested in tension was 886+/-221 N. This data should be suitable for investigating fracture biomechanics and the testing of orthopaedic constructs commonly used for fracture stabilization in the feline patient.     

Arthrodesis of the equine proximal interphalangeal joint: a mechanical comparison of 2 parallel 5.5 mm cortical screws and 3 parallel 5.5 mm cortical screws

OBJECTIVE: To compare the biomechanical characteristics and mode of failure of 2 techniques using parallel 5.5 mm screws for pastern joint arthrodesis in horses. STUDY DESIGN: Randomized block design, for horse (1-5), method of fixation (two 5.5 mm screws versus three 5.5 mm screws), side (right, left), and end (front, hind). Constructs were tested to failure in 3-point bending. SAMPLE POPULATION: Twenty limbs (5 cadavers). METHODS: A combined aiming device was used to facilitate screw placement. Two parallel 5.5 mm screws were inserted in lag fashion in 1 limb of a pair, and three 5.5 mm screws were inserted in the contralateral limb. Constructs were then tested in 3-point bending in a dorsal-to-palmar (plantar) direction using a materials testing machine at a loading rate of 19 mm/s. Maximal bending moment at failure and stiffness were obtained from bending moment-angular deformation curves. RESULTS: There was no significant difference between two and three 5.5 mm screw constructs for bending moment and stiffness (P<.05). All constructs ultimately failed by bone fracture or screw bending. For proximal interphalangeal (PIP) joint arthrodesis constructs loaded in 3-point bending, no significant effect of treatment, side, or end on maximal bending moment or stiffness was detected. CONCLUSIONS: Two 5.5 mm cortical screws inserted in parallel should provide a surgically simpler and equally strong PIP joint arthrodesis compared with three 5.5 mm cortical screws. CLINICAL RELEVANCE: Two 5.5 mm cortical screws inserted in parallel for PIP joint arthrodesis should perform similarly under conditions used in this study, as three 5.5 mm screws inserted in a similar manner, when loaded under bending.     

Holding Power of Orthopedic Screws in Equine Third Metacarpal and Metatarsal Bones: Part I. Foal Bone

The holding power of orthopedic screws in the third metacarpal and metatarsal cadaver bones of foals that were aged from 1 to 14 days was tested. Comparative trials between screws inserted at the same site in contralateral bones from the same foal were performed to compare the holding power of 5.5 mm cortical and 6.5 mm cancellous screws in the metaphysis, and the holding power of 5.5 and 4.5 mm cortical screws in the diaphysis. A MTS servohydraulic tensile testing machine was used to perform screw pullouts at a displacement rate of 19 mm/sec. There was no significant difference between maximum holding power of 5.5 mm cortical screws and 6.5 mm cancellous screws in the metaphysis when expressed as kg per mm of bone width at the screw insertion site (p = 0.097) or as kg per mm of screw thread engaged in the bone (p = 0.17). There was no significant difference in holding power of 5.5 and 6.5 mm screws in the proximal versus distal metaphysis (p = 0.10). The 5.5 mm screws had significantly greater holding power than the 4.5 mm screws in the diaphysis (p = 0.0097). Fixation failure at screw pullout was always due to bone shear. In internal fixation in foal bone, the 5.5 mm screws may be a suitable alternative to 6.5 mm screws in the metaphysis. Use of 5.5 mm rather than 4.5 mm screws is recommended in the diaphysis because of greater holding power.     

Axial pull-out strength of 3.5 cortical and 4.0 cancellous bone screws placed in canine proximal tibias using manual and power tapping

An in vitro experimental cadaveric mechanical testing study was performed using 20 radiographically mature dogs, weighing between 18-33 kg. The aim of the study was to compare the axial pull-out strength of 3.5 mm cortical and 4.0 mm cancellous bone screws inserted in the canine proximal tibia using manual and power tapping techniques. 3.5 cortical and 4.0 cancellous bone screws were inserted in canine cadaver proximal tibiae using a manual or power tapping technique. The screws were extracted using a servohydraulic materials testing machine in order to measure axial pull-out strength. Axial pull-out strength was recorded relative to the total bone width and total cortical width of each tibia. The mean axial pull-out strength for all constructs was 717.8+/-56.5 N without any statistically significant difference among groups (p=0.4183). The groups were equal in animal body weight, cortical width and total bone width (p=0.2808). The axial pull-out strength in proportion to cortical and total bone width was not significantly different among groups (p=0.5318). Axial pull-out strengths of 3.5 mm cortical and 4.0 mm cancellous bone screws inserted in the proximal tibial metaphysis were not significantly different. Axial pull-out strength was not affected by the use of power tapping in either screw type.     

Static Strength Evaluation of Sacroiliac Fracture-Separation Repairs

The relative static strengths of seven fixation configurations for the repair of sacroiliac fracture-separations were determined. The fixation techniques were two 3.5 mm screws, one 4.5 mm screw, one 4.5 mm screw and a pin, two 4.5 mm screws, one 6.5 mm screw, one 6.5 mm screw and a pin, and two 6.5 mm screws. Each configuration was subjected to a torsional, a bending, and a shear disruptive force while the maximum load tolerated before failure was measured. Two screws were stronger than a single screw of similar size, two small screws were stronger than a single larger screw, and a reduction pin added no significant strength to a single screw repair. It was concluded that use of the largest screws possible will maximize the strength of a sacroiliac fracture-separation repair.     

Screw fixation in lag fashion of equine cadaveric metacarpal and metatarsal condylar bone specimens: a biomechanical comparison of shaft and cortex screws

OBJECTIVE: To compare acute fixation stability and insertion effort of cortex bone screws with and without a shaft inserted in lag fashion in equine metacarpal (metatarsal, MC(T)III) bone. METHODS: Screw types with independent variables of screw diameter (4.5 or 5.5 mm) and shaft type (without shaft, with 20-mm shaft, or with 25-mm shaft) were studied. Bone specimens cut from distal equine MC(T)III condyles were used. After screw insertion in lag fashion into 2 bone blocks with an instrumented device, shear tests were conducted in a mechanical testing machine. Outcome variables of peak insertion torque, insertion energy, stiffness. yield strength, and displacement at 3 kN of load were compared. RESULTS: The effects of screw design were substantial. Screws with shaft were 30% to 40% stiffer and 60% to 70% stronger than screws without shaft. Screws with shaft could tolerate 80 to 95 kg more force than screws without shaft before yielding. At 3 kN load, the displacement with screws with shaft was 55% to 60% of that with screws without shaft. Screws with a long shaft tended to perform better than those with a short shaft. There was no difference in the shear stiffness, shear yield strength, or shear displacement between the 2 screw diameters. Although larger diameter screws required more insertion effort, and screws with a short shaft required the most insertion energy, these differences were small. CONCLUSIONS: Cortex screws with a long shaft of 4.5- or 5.5-mm diameter provide better stability in equine MC(T)III condyle bone with less insertion effort compared with those with a short shaft or no shaft. CLINICAL SIGNIFICANCE: Cortex bone screws with a shaft inserted in lag fashion should be considered for the fixation of equine MC(T)III condylar fractures.     

Early detection and treatment of screw loosening in triple pelvic osteotomy

OBJECTIVE: To detect early screw loosening in triple pelvic osteotomy (TPO) and to evaluate the efficacy of retightening using fluoroscopic guidance and minimally invasive surgery to maintain acetabular alignment and achieve bone healing. STUDY DESIGN: Prospective clinical study. SAMPLE POPULATION: Sixteen dogs that had TPO. METHODS: Dogs (16) had TPO (21) by using pre-angled plates secured with 3.5 and 4.0 mm screws, with ischiatic or iliac cerclage, for osteosynthesis. In all but 1 TPO at least 1 screw was inserted into the sacral body (43 screws). The mean radiographic screw length inserted in the sacrum was 10.2 mm, and the mean percent sacral engagement was 22%. Dogs were examined clinically and radiographically immediately postoperatively, and at 10, 30, 60, and 90 days to evaluate screw position. Loose screws were retightened through stab incisions using fluoroscopy to locate the screw. RESULTS: TPO was performed without operative complications. At 10 days, 12 TPOs (57%; 11 dogs) had loose screws primarily located in the cranial aspect of the plate. This represented 20% (25) of the inserted screws. In 5 dogs, screw loosening resulted in medial rotation of the acetabular segment. All loose screws were retightened; 3 screws loosened again in 2 dogs and were detected at 60 days. However, the osteotomies healed with the planned acetabular rotation without further intervention. Screw tightening corrected the acetabular segment displacement. Screws correctly seated at 10 days did not subsequently loosen. Clinical and radiographic outcome was judged excellent in all dogs. CONCLUSION: Loose screws in TPO plates can be identified by 10 days postoperatively and retightened using fluoroscopic guidance to achieve acetabular realignment and healing without need for further surgery. CLINICAL RELEVANCE: Postoperative radiographic evaluation of screw position at 10 days after TPO is recommended to detect loose screws. Retightening loose screws should be considered as an alternative to TPO revision or confinement, especially in immature dogs.     

Comparison of computer-assisted surgery with conventional technique for the treatment of axial distal phalanx fractures in horses: an in vitro study

OBJECTIVES: To compare the precision obtained with computer-assisted screw insertion for treatment of mid-sagittal articular fractures of the distal phalanx (P3) with results achieved with a conventional technique. STUDY DESIGN: In vitro experimental study. SAMPLE POPULATION: Thirty-two cadaveric equine limbs. METHODS: Four groups of 8 limbs were studied. Either 1 or 2 screws were inserted perpendicular to an imaginary axial fracture of P3 using computer-assisted surgery (CAS) or conventional technique. Screw insertion time, predetermined screw length, inserted screw length, fit of the screw, and errors in placement were recorded. RESULTS: CAS technique took 15-20 minutes longer but resulted in greater precision of screw length and placement compared with the conventional technique. CONCLUSION: Improved precision in screw insertion with CAS makes insertion of 2 screws possible for repair of mid-sagittal P3 fractures. CLINICAL RELEVANCE: CAS although expensive improves precision in screw insertion into P3 and consequently should yield improved clinical outcome.     

Axial compression generated by cortical and cancellous lag screws in the equine distal phalanx

Lag screw fixation using single 4.5 mm cortical bone screws is a recommended technique for repair of mid-sagittal plane fractures of the distal phalanx in adult horses. However, implant infection and technical difficulties in obtaining adequate interfragmentary compression have made this surgical procedure somewhat controversial. We hypothesized that use of larger diameter screws would result in increased axial compression and improved stability of this fracture.Paired distal phalanges from the forelimbs of 10 adult horses were collected at necropsy and divided in half in the midsagittal plane. Using a randomized block study design, four types of bone screws (4.5 mm cortical, 5.5 mm cortical, 6.5 mm cancellous pre-tapped, and 6.5 mm cancellous non-tapped) were inserted to a depth of 15 mm. During screw insertion, the axial force generated under the screw head was measured with a load washer containing a piezoelectric force transducer, while torque of insertion was recorded with a torsional testing machine. The 6.5mm screw inserted after pre-tapping generated significantly greater axial force (2781 N) than the 4.5 mm (1522 N), 5.5 mm (2073 N) or 6.5 mm non-tapped (2295 N) screws. The relationship between maximal applied torque and axial force generated was linear for each screw type. Each unit of torque applied during insertion of cortical screws resulted in a greater increase in axial compression, as compared to cancellous screws. These data suggest that use of larger diameter screws would result in improved interfragmentary compression of distal phalangeal fractures.