豆浆处理工艺改善内酯豆腐的质构特性

豆浆的粒子大小可以通过一定的处理工艺加以改变,从而提高内酯豆腐质构特点。该文研究了胶体磨磨齿间隙(10~30μm)、超声波功率强度(1~3 W/g)、匀浆机转速(1 000~5 000 r/min)对内酯豆腐质构特点的影响。结果表明胶体磨处理能显著(p0.05)提高内酯豆腐的弹性和内聚性。但在间隙为10μm的情况下,长时间研磨会降低硬度。在不同超声波功率强度条件下,内酯豆腐的硬度和弹性都是先上升后下降。超声波处理会显著(p0.05)降低内酯豆腐的内聚性。匀浆处理对内酯豆腐的质构特点均产生先上升后下降的影响。通过Topsis法进行多指标综合评价,得出较好的豆浆处理工艺是匀浆处理1 000 r/min处理8 min。粒径分析结果证明处理工艺能降低豆浆粒径大小。豆浆处理工艺可以改善内酯豆腐的质构特点,从而满足人们的不同需求。     

Enhancement of tofu isoflavone recovery by pretreatment of soy milk with koji enzyme extract

Isoflavones are novel nutraceutical constituents of soybeans, but considerable amounts are lost in the whey during conventional tofu manufacturing. In this study, in a small-scale process, 2 mL of koji enzyme extract (soybean koji/deionized water, 1/3, w/v) was combined with 600 mL of soy milk, and 30 mL aliquots were incubated at 35 degrees C for 0, 30, 60, 120, and 300 min, for enzyme pretreatment. After each treatment time, soy milk was heated to 85 degrees C, CaSO4 was added to aggregate protein, and the mixture was centrifuged to separate the solids (tofu) from the whey. The tofu yield and moisture contents from soy milk treated for 30 or 60 min were higher than those from soy milk treated for 0 (control), 120, or 300 min. The protein content of freeze-dried tofu varied in a limited range, and native PAGE and SDS-PAGE patterns revealed slight quantitative and qualitative variations among products. Soy milk daidzein and genistein contents increased while daidzin and genistin contents decreased as the time of enzyme pretreatment of the soy milk increased. After 30 min of pretreatment, daidzin, genistin, daidzein, and genistein contents recovered in tofu products were higher than those of the control. In a pilot-scale process, aliquots (3 L) of soy milk were enzyme-treated for 30 min, aggregated with CaSO4, and hydraulically pressed to remove the whey. As in pretreatments, soy milk daidzein and genistein contents increased while daidzin and genistin contents decreased. In a comparison of the control and enzyme-treated tofu products, the total recoveries of daidzin, genistin, daidzein, and genistein in the tofu products increased from 54.9% to 64.2%. When the tofu products were subjected to a sensory panel test, both products were judged acceptable.     

Effect of soy milk characteristics and cooking conditions on coagulant requirements for making filled tofu

The amount of coagulant added to soy milk is a critical factor for tofu-making; particularly it affects the textural properties of tofu. Earlier research indicated that the critical point of coagulant concentration (CPCC) is a characteristic parameter of soy milk and could be used as an effective indicator of optimal coagulant concentration (OCC) for making filled tofu. The objective of this study was to investigate the possible correlations between CPCC and the characteristics of soy milk made from various soybean samples and the effect of soy milk cooking and dilution conditions on CPCC. CPCC was determined by a titration method. Calcium chloride and magnesium chloride were used as coagulants. Soy milk characteristics including solid, protein, phytate, pH, titratable acidity, mineral content, and 11S/7S protein and these characteristics as affected by heating rate, heating time, and sequence of dilution and heating were studied. The results showed that the CPCC was significantly (p < 0.05) positively correlated with phytate content (grams per gram of protein), pH, and 7S protein content but negatively correlated with protein content, 11S protein content, 11S/7S ratio, titratable acidity, and original calcium content. Within the same soybean material, more proteins required more coagulant, but higher protein concentration during cooking resulted in less coagulant required by each gram of protein during coagulation. The CPCC decreased with increasing soy milk heating time or decreasing heating rate. The sequence of heating and diluting for preparing soy milk also had an effect on CPCC.     

Assessment of soy genotype and processing method on quality of soybean tofu

Protein quality in six soybean varieties, based on subunit composition of their protein, was correlated with quality of the produced tofu. Also, protein changes due to a pilot plant processing method involving high temperature/pressure and commercial rennet as coagulant were assessed. In each soybean variety, glycinin (11S) and β-conglycinin (7S) as well as 11S/7S ratio significantly changed from beans to tofu. Between varieties, the 11S/7S protein ratio in seed indicated genotypic influence on tofu yield and gel hardness (r = 0.91 and r = 0.99, respectively; p < 0.05). Also, the 11S/7S ratio correlated with soymilk pH (r = 0.89, p < 0.05), leading to a relationship between soymilk pH with protein recovery and yield of tofu (r = 0.94 and r = 0.91, respectively; p < 0.05). The soybean β'-subunit of 7S protein negatively influenced tofu hardness (r = -0.91, p < 0.05). Seed protein composition and proportion of 7S protein subunits under the applied production method had an important role in defining tofu quality.     

不同贮藏期大豆蛋白对千页豆腐品质的影响

为了研究不同贮藏期大豆分离蛋白（soy protein isolate,SPI）对千页豆腐品质的影响,该文首先研究了贮藏期对大豆分离蛋白结构的影响,进而探讨贮藏期对大豆蛋白制备千页豆腐的品质的影响。对不同贮藏期的大豆蛋白分别采用了凝胶质构特性、感官评价、羰基含量、大豆蛋白亚基以及巯基的测定,并采用拉曼光谱对大豆蛋白二级结构、二硫键构型以及侧链结构进行了分析,同时采用扫描电镜观察千页豆腐的微结构。结果表明：随着贮藏期的延长,千页豆腐的感官评价变差,由88分降低至44分;其凝胶网络结构逐渐疏松;大豆蛋白羰基含量逐渐上升;巯基含量逐渐下降;二级结构含量改变;凝胶硬度呈下降趋势,硬度值低于234 g时,将无法达到千页豆腐的质量要求。这表明在贮藏期内SPI发生了氧化,导致大豆蛋白质结构发生改变,使其凝胶性质下降。     

Optimizing conditions for thermal processes of soy milk

Mathematical and kinetic models were set up for heat-induced quality changes in soy milk, including inactivation of trypsin inhibitor activity (TIA) and degradation of thiamin, riboflavin, color, and flavor over a wide range of time-temperature combinations with particular interest in the ultrahigh-temperature (UHT) range. On the basis of these models, multiresponse optimization of the thermal processes for soy milk was carried out to obtain the following effects simultaneously: (1) maximum destruction of bacterial spores, (2) maximum inactivation of TIA, and (3) minimum degradation of sensory and nutritional qualities. By a suitable selection of high temperatures and extended heating times, for example, 143 degrees C/60 s, it is possible to use a single-step UHT process to produce a commercially sterile soy milk with satisfactory TIA inactivation, highly acceptable color and flavor, and thiamin retention between 90 and 93%.     

Changes in the profile of genistein, daidzein, and their conjugates during thermal processing of tofu.

Profiles of genistein, daidzein, genistin, daidzin, and their acetyl- and malonyl-beta-glycosides were determined in tofu as affected by temperature and time. Tofu was heated in water at 80, 90, and 100 degrees C for 0 (control), 10, 20, 30, and 40 min, and the contents of the isoflavones of interest were quantified using reversed-phase HPLC. Total isoflavone content decreased most likely due to leaching of isoflavones into the water. Because the content of the isoflavones of the genistein series was little affected by the treatments, the decrease in the total isoflavone content was almost exclusively due to a decrease of the daidzein series. Changes in the profile of the daidzein series suggest little decarboxylation of the malonylglycoside to the acetylglycoside, but considerable de-esterification of the malonyl- and acetylglycoside to the beta-glucoside. Strongly temperature dependent decreases of the aglycon suggest possible thermal degradation of daidzein in addition to losses due to leaching.     

Instrumental and sensory characterization of heat-induced odorants in aseptically packaged soy milk

Predominant heat-induced odorants generated in soy milk by ultrahigh-temperature (UHT) processing were evaluated by sensory and instrumental techniques. Soy milks processed by UHT (143 degrees C/14 s, 143 degrees C/59 s, 154 degrees C/29 s) were compared to a control soy milk (90 degrees C/10 min) after 0, 1, and 7 days of storage (4.4 +/- 1 degrees C). Dynamic headspace dilution analysis (DHDA) and solvent-assisted flavor evaporation (SAFE) in conjunction with GC-olfactometry (GCO)/aroma extract dilution techniques and GC-MS were used to identify and quantify major aroma-active compounds. Sensory results revealed that intensities of overall aroma and sulfur and sweet aromatic flavors were affected by the processing conditions. Odorants mainly responsible for the changes in sulfur perception were methional, methanethiol, and dimethyl sulfide. Increases in 2-acetyl-1-pyrroline, 2-acetyl-thiazole, and 2-acetyl-2-thiazoline intensities were associated with roasted aromas. A marginal increase in intensity of sweet aromatic flavor could be explained by increases in 2,3-butanedione, 3-hydroxy-2-butanone, beta-damascenone, and 2- and 3-methylbutanal. Predominant lipid-derived odorants, including (E,E)-2,4-nonadienal, (E,E)-2,4-decadienal, (E,Z)-2,4-decadienal, (E)-2-nonenal, (E)-2-octenal, 1-octen-3-one, 1-octen-3-ol, and (E,Z)-2,6-nonadienal, were affected by processing conditions. Intensities of overall aroma and sulfur notes in soy milk decreased during storage, whereas other sensory attributes did not change. Color changes, evaluated by using a Chroma-meter, indicated all UHT heating conditions used in this study generated a more yellow and saturated color in soy milk in comparison to the control soy milk.     

Stability of isoflavones in soy milk stored at elevated and ambient temperatures

Soy isoflavones are widely recognized for their potential health benefits. The increased use of traditional and new food products calls for the assessment of their stability during processing and storage. The present study examines the stability of genistein and daidzein derivatives in soy milk. Soy milk was stored at ambient and elevated temperatures, and the change in isoflavone concentration was monitored with time. Genistin loss in time showed typical first-order kinetics, with rate constants ranging from 0.437-3.871 to 61-109 days(-1) in the temperature ranges of 15-37 and 70-90 degrees C, respectively. The temperature dependence of genistin loss followed the Arrhenius relation with activation energies of 7.2 kcal/mol at ambient temperatures and 17.6 kcal/mol at elevated temperatures. At early stages of soy milk storage at 80 and 90 degrees C, the 6' '-O-acetyldaidzin concentration increased, followed by a slow decrease. The results obtained in this study can serve as a basis for estimating the shelf life of soy milk as related to its genistin content.     

Changes in element concentrations during Andosol formation on tephra in Japan

Andosol formation involves the rapid, abundant and in situ formation of non‐crystalline materials from tephra deposits. A large amount of humus complexed with Al also accumulates in the A horizons. As these materials are rich in Al or Fe compared to the parent tephra, the concentrations of the major and minor elements change significantly during Andosol formation. The objectives of this study were to examine how the rock type of the tephra and its weight loss during the formation process affect the changes in the element concentrations of Andosols. A total of 95 samples with different rock types from 18 pedons of Andosols in Japan were used to determine the total concentrations of 54 elements. Principal component analysis suggested that the degree of weathering and the rock types of parent tephra are the important factors in the variation of the element concentrations in Andosols. Three rock types, dacitic, andesitic and basaltic‐andesitic, were identified from the V and Zn contents of ferromagnetic minerals separated from the Andosol samples. Basaltic Andosols were identified from the abundant coloured volcanic glass and olivine in the sand fraction. Regarding concentrations of 41 elements, at least one group based on rock type was significantly different from one to three other groups at the P= 0.05 level. The content of oxalate‐extractable Si (Si_o), Al (Al_o) and Fe (Fe_o) was used as an index to show the extent of Andosol development. Relatively strong correlations between the element concentrations and Si_o, Al_o and Fe_o as well as other weathering indices were found in the andesitic samples. Among these elements, at least 27 (Be, Al, Ti, Fe, Y, Zr, Nb, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu, Hf, Ta, Tl, Pb, Th and U) were enriched in the Andosols and the increases in these concentrations were related to total weight loss due to soil formation processes.     

Incorporation of soy milk lipid into protein coagulum by addition of calcium chloride.

Lipid holding in tofu (soybean curd) has such stability that it is not released even when it is cooked. The lipid in soy milk is incorporated into the tofu with coagulation of proteins on processing by the addition of a calcium salt. In this study, the incorporation of lipid into the coagulum was examined from the association with protein. The lipid in soy milk was obtained as the floating fraction by centrifugation. The floating fraction decreased by the addition of calcium chloride prior to forming a protein coagulum. When half of the protein coagulated, all of the floating fraction became inseparable. The protein in soy milk, then, was separated into particulate and soluble fractions by centrifugation. The decrease of the floating fraction with added calcium chloride was parallel to the coagulation of the particulate protein. The association of the floating fraction and the soluble protein occurred after the new particles formed from the soluble proteins. These results indicated that the lipid incorporation took place by the conjugation of the lipid and protein particles.     

Composition of proteins in okara as a byproduct in hydrothermal processing of soy milk

Protein quality, based on its subunit composition, in okara obtained as a byproduct during hydrothermal cooking of soy milk was assessed. The composition of 7S and 11S protein fractions was correlated with the physicochemical properties of protein in okara produced from six soybean varieties. The basic 7S globulin (Bg7S) and 11S protein were two main proteins in okara. Investigated soybean genotypes produced okara with mainly acidic A(5) and basic B(1,2,4) polypeptides of 11S proteins. Soybean 11S content was not an indicator of okara protein recovery or extractability. Of all tested relationships, extractable soluble protein content of okara was influenced only by soybean Bg7S (r = 0.86; p < 0.05) and its light subunit contents (r = 0.93; p < 0.05). Okara protein recovery depended on Bg7S heavy subunit content in soybeans (r = 0.81; p < 0.05). The high quantity of vegetable protein in okara (around 35%) and very high protein extractability (around 85%) qualify this byproduct for potential application in food preparation as a functional ingredient.     

Characteristics and use of okara, the soybean residue from soy milk production--a review

Large quantities of okara produced annually pose a significant disposal problem. It contains mostly crude fiber composed of cellulose, hemicellulose, and lignin, about 25% protein, 10-15% oil, but little starch or simple carbohydrates. It is a suitable dietary additive in biscuits and snacks because it reduces calorie intake and increases dietary fiber. The high-quality protein fraction has good water holding and emulsifying qualities and contains a peptide with anti-hypertension effects. The pectic polysaccharides fraction is suitable for thickening acid milk products. Okara fermented with Actinomucor elegans (meitauza), Aspergillus oryzae (koji), Neurospora intermedia (ontjom), and Rhizopus oligosporus (tempe), on consumption, reduces cholesterol level and contains substances that counteract dietary free radicals. Unique and useful products produced by Bacillus subtilis and Penicillium simplicissimum on okara include surfactin and iturin A (fungicidal), okaramines A, B, D-F (D is insecticidal), an oleanane triterpene, and two dihydroquinolinones (one toxic for Artemia salina). Okara has been used as silkworm food and in the production of ceramics.     

Changes in structures of milk proteins upon photo-oxidation

Changes in protein structures as a result of riboflavin-induced photo-oxidation were studied for six milk proteins: alpha-casein, beta-casein, kappa-casein, lactoferrin, alpha-lactalbumin, and beta-lactoglobulin. The milk proteins showed significant variability in sensitivity to photo-oxidation. After photo-oxidation, an increase in carbonyl content because of oxidation of tryptophan, histidine, and methionine, as well as formation of dityrosine, was observed for all proteins studied, although at very different levels. Generally, the increment was highest for alpha- and beta-casein and was lowest for lactoferrin. Loss of tryptophan because of photo-oxidation was well-correlated with the formation of the tryptophan oxidation products, N-formylkynurenine and kynurenine. Changes at the tertiary protein structure level were observed after photo-oxidation of the globular proteins, where tryptophan fluorescence emission indicated unfolding of alpha-lactalbumin and beta-lactoglobulin, whereas lactoferrin achieved a more compact tertiary structure. Changes in secondary structure were observed for alpha-lactalbumin and beta-lactoglobulin, whereas the secondary structure of lactoferrin did not change. Polymerization of alpha- and beta-casein and of lactoferrin was observed, whereas kappa-casein, alpha-lactalbumin, and beta-lactoglobulin showed little tendency to polymerize after photo-oxidation. Lability toward photo-oxidation is discussed according to the structural stabilities of the globular proteins.     

Changes and roles of secondary structures of whey protein for the formation of protein membrane at soy oil/water interface under high-pressure homogenization

The conformational changes of whey proteins upon adsorption at the soy oil/water interface were investigated using Fourier transform infrared (FT-IR) spectroscopy. Significant changes were observed in the bands assigned to beta-sheets and alpha-helix structures following the adsorption of proteins at the oil/water interface. The remaining interfacial proteins after Tween 20 desorption revealed small changes in beta-sheet and alpha-helical structures, whereas in the desorbed whey proteins the unordered structures largely increased, and beta-sheet structures almost disappeared. These FT-IR results provide important knowledge about the conformational modifications in whey proteins occurring upon adsorption at the oil/water interface. Finally, specific conformational changes are necessary to stabilize emulsions: adsorption-induced unfolding, increase in alpha-helical structures to establish interactions with the oil phase, and aggregation between adsorbed whey proteins to form protein membranes. Moreover, the structural changes in whey protein adsorbed at the oil/water interface under high-pressure homogenization are irreversible.     

Stability of isoflavones during extrusion processing of corn/soy mixture

The influence of extrusion processing in the presence of corn on the quantity and quality of genistein, daidzein, and their respective beta-glucoside, acetyl glucoside, and malonyl glucoside derivatives was evaluated. Products of 100% soy (textured) and a blend of 20% soy protein concentrate (SPC) and 80% corn meal (direct-expanded) were extruded, with evaluations before and after extrusion. In addition, a 3 x (3 x 3) split-plot factorial experiment investigated the influence of barrel temperature (110, 130, 150 degrees C), moisture content (22, 24, 26%), and relative residence time (1, 0.8, 0.6) on extruder response and isoflavone profile. The extrusion barrel temperature had the most influence on isoflavone profile, especially decarboxylation of the malonyl beta-glucoside, followed by the moisture content. The amount of extractable isoflavones decreased after extrusion for both the SPC and SPC/corn meal blend when extracted with 80% aqueous methanol but remained approximately the same when first hydrated with water before extraction. However, initially hydrating with water produced enzymatic glycolysis in the unextruded samples, increasing the aglycons dramatically.     

Photosensitizing effect of riboflavin, lumiflavin, and lumichrome on the generation of volatiles in soy milk

Lumichrome and lumiflavin were formed from riboflavin under light. pH had a significant influence on the formation of lumichrome and lumiflavin from riboflavin. Lumichrome was the only major product from riboflavin under neutral or acidic pH values. Lumiflavin was also formed from riboflavin in basic pH. The maximum concentration of lumiflavin from 100 microM riboflavin at pH 8.5 was 30.9 microM, and it was reached after 2 h of exposure at 1500 lux. The maximum concentration of lumichrome formed from 100 microM riboflavin at pH 4.5, 6.5, or 8.5 was 79.9, 58.7, and 73.1 microM, respectively, after 8, 6, or 2 h of light exposure. The formation of lumichrome and lumiflavin from riboflavin was due to the type I mechanism of the riboflavin photosensitized reaction. Singlet oxygen was also involved in the photosensitized degradation of lumiflavin and lumichrome. The reaction rates of riboflavin, lumiflavin, and lumichrome with singlet oxygen were 9.66 x 10(8), 8.58 x 10(8), and 8.21 x 10(8) M(-1) s(-1), respectively. The headspace oxygen depletion and headspace volatile formation were significant in soy milk containing lumichrome or lumiflavin under light (p < 0.05) and were insignificant (p > 0.05) in the dark. Ascorbic acid could inhibit the total volatile changes of soy milk under light. Soy milk should be protected from light to prevent the photodegradation of riboflavin and the oxidation of soy milk.     

Determination of choline in milk, milk powder, and soy lecithin hydrolysates by flow injection analysis and amperometric detection with a choline oxidase based biosensor

A fast-response and interference-free amperometric biosensor based on choline oxidase immobilized onto an electropolymerized polypyrrole film for flow injection determination of choline in milk, milk powder, and soy lecithin hydrolysates is described. The sensor displayed an Imax value of 1.9 +/- 0.2 microA and an apparent Michaelis-Menten constant, k'M, equal to 1.75 +/- 0.07 mM. Detection limits of 0.12 microM could be obtained. Because even a slight deterioration of the anti-interference membrane can adversely affect measurement accuracy, a real time monitoring of the biosensor selectivity has been achieved by a dual Pt electrode flow-through cell where the enzyme modified electrode is coupled to an enzyme-free electrode in a parallel configuration. Finally, bracketing technique (alternate injections of sample and standards) allows a two-point calibration to be performed in real-time, correcting for any drift in sensor response.     

Stability and bioaccessibility of isoflavones from soy bread during in vitro digestion

The impact of simulated digestion on the stability and bioaccessibility of isoflavonoids from soy bread was examined using simulated oral, gastric, and small intestinal digestion. The aqueous (bioaccessible) fraction was isolated from digesta by centrifugation, and samples were analyzed by high-performance liquid chromatography (HPLC). Isoflavonoids were stable during simulated digestion. Partitioning of aglycones, acetylgenistin, and malonylgenistin into the aqueous fraction was significantly (P < 0.01) affected by the concentration of bile present during small intestinal digestion. Omission of bile resulted in nondetectable genistein and <40% of total daidzein, glycitein, and acetylgenistin in the aqueous fraction of digesta. Partitioning of these compounds into the aqueous fraction was increased by physiological concentrations of bile extract. These results suggest that micellarization is required for optimal bioaccessibility of isoflavonoid aglycones. We propose that the bioavailability of isoflavones from foods containing fat and protein may exceed that of supplements due to enhanced bile secretion.     

Luminex-based triplex immunoassay for the simultaneous detection of soy, pea, and soluble wheat proteins in milk powder

An automated fluorescent microsphere-based flow cytometric triplex immunoassay, using the Luminex 100 flow analyzer with MultiAnalyte Profiling (xMAP) technology, was developed for the simultaneous detection of proteins from three vegetable sources as potential fraudulent adulterants in milk powder. In the final triplex inhibition immunoassay, soluble wheat proteins (SWP) and proteins from soy and pea were coupled to three different microsphere sets. A mixture of these microsphere sets was transferred to a microtiter plate well together with the sample and a mixture of three affinity-purified polyclonal antibodies raised against the proteins and labeled with a fluorophore (Alexa 532). After incubation for 1.5 h at room temperature in the dark, the fluorescence intensities on the microspheres were directly measured (no wash procedure) in the Luminex during 10 s per well (100 microspheres per set). The sensitivities of the three assays for plant protein extracts were determined as 0.5-0.6 microg/mL at 50% inhibition. For the detection of the vegetable proteins in milk powder, the samples were dissolved in buffer (0.1 g in 10 mL) and further diluted (20 times) to create a 50% inhibition at approximately 0.5% of the vegetable proteins in the total protein content of milk powder. With the help of calibration standards, prepared under conditions comparable to those for sample materials, the triplex immunoassay proved to be quantitative above 0.1%, although concentrations in high-heated milk powders were underestimated. Due to the xMAP technology, in which 100 different microsphere sets can be distinguished, this triplex immunoassay can easily be extended to detect other possible adulterants.