Effect of surface treatment of jute fibers on the interfacial adhesion in poly(lactic acid)/jute fiber biocomposites

Jute fibers have immense potential to be used as natural fillers in polymeric matrices to prepare biocomposites. In the present study jute fibers were surface treated using two methods: i) alkali (NaOH) and ii) alkali followed by silane (NaOH+Silane) separately. Effects of surface treatments on jute fibers surface were characterized using fourier transform infrared spectroscopy (FT-IR) and scanning electron microscopy (SEM) analyses. Further, the effects of surface treatments on jute fibers properties such as crystallinity index, thermal stability, and tensile properties were analyzed by X-ray diffraction method (XRD), thermo gravimetric analysis (TGA), and single fiber tensile test respectively. The effects of surface treatment of jute fibers on interphase adhesion between of poly(lactic acid) (PLA) and jute fibers were analyzed by performing single fiber pull-out test and was examined in terms of interfacial shear strength (IFSS) and critical fiber length.     

Fabrication of long and discontinuous natural fiber reinforced polypropylene biocomposites and their mechanical properties

Natural fiber reinforced polypropylene (PP) biocomposites were fabricated by blending long-and-discontinuous (LD) natural fibers (NF) with LD PP fibers. Firstly, random fiber mats were prepared by mixing NFs and PP fibers using a carding process. Then, heat and pressure were applied to the mats, such that the PP fibers dispersed in the mats melted and flowed out, resulting in the formation of consolidated sheets upon subsequent cooling. The effect of the fiber volume fraction on the mechanical properties of the bio-composites was scrutinized by carrying out tensile and flexural tests and observing the interface between the fiber and matrix. It was observed that the natural LD fiber content needs to be maintained at less than the nominal fiber fraction of 40 % by weight for the composites fabricated using the current method, which is quite low compared to that of continuous or short fiber reinforced composites. The limited fiber fraction can be explained by the void content in the biocomposites, which may be caused by the non-uniform packing or the deficiency of the matrix PP fibers.     

Effect of the low and radio frequency oxygen plasma treatment of jute fiber on mechanical properties of jute fiber/polyester composite

We investigated the surface modification of jute fiber by oxygen plasma treatments. Jute fibers were treated in different plasma reactors (radio frequency “RF” and low frequency “LF” plasma reactors) using O₂ for different plasma powers to increase the interface adhesion between jute fiber and polyester matrix. The influence of various plasma reactors on mechanical properties of jute fiber-reinforced polyester composites was reported. Tensile, flexure, short beam shear tests were used to determine the mechanical properties of the composites. The interlaminar shear strength increased from 11.5 MPa for the untreated jute fiber/polyester composite to 19.8 and 26.3 MPa for LF and RF oxygen plasma treated jute fiber/polyester composites, respectively. O₂ plasma treatment also improved the tensile and flexural strengths of jute fiber/ polyester composites for both plasma systems. It is clear that O₂ plasma treatment of jute fibers by using RF plasma system instead of using LF plasma system brings about greater improvement on the mechanical properties of jute/polyester composites.     

Effects of heat treatment on the properties of bamboo fiber/polypropylene composites

In this paper, the effects of heat treated parameters on the properties of bamboo fiber (BF) / polypropylene (PP) composites were investigated. The crystallization properties of BF/PP composites after heat treatment were characterized by differential scanning calorimetry (DSC), and the mechanical properties were measured. The results showed that the crystallinities of the heat treated composite were enhanced compared with that of the untreated. When the heat treated time was 30 mins, the crystallinities became almost unchanged. However, the crystallinity decreased after 12 h heat treatment. In addition, when the heat treated temperature was above 90 °C, the higher the temperature was, the higher the crystallinities became. Moreover, the tensile strengths of BF/PP composites increased and then decreased with increasing heat treated time, while the impact strengths had a decreasing trend. In the meanwhile, the tensile strengths increased but the impact strengths decreased as the heat temperature increased.     

Effect of coir fiber content and compatibilizer on the properties of unidirectional coir fiber/polypropylene composites

The main objective of this research was to study the effect of fiber content variation and stearic acid (SA) treatment on the fundamental properties of unidirectional coir fiber (CF) reinforced polypropylene (PP) composites. Several percentages of filler contents were used (10–40 wt %) in order to gain insights into the effect of filler content on the properties of the composites. Coir/PP composites were fabricated by compression molding, and the properties of composites were studied by physico-mechanical and thermal properties. The results from mechanical properties such as tensile strength (TS), tensile modulus (TM) and impact strength (IS) of the CF/PP composites were found to be increased with increasing fiber content, reached an optimum and thereafter decreased with further increase in fiber content. Treatment of the coir with SA as the coupling agent enhanced the mechanical properties, crystallization temperature and crystallinity of virgin PP and water desorption of the resulting composites, resulting from the improved adhesion between the CF and PP matrix. Scanning electron micrographs (SEM) of the tensile fractured samples showed improved adhesion between fiber and matrix upon treatment with SA. Interfacial shear strength (IFSS) of the composites was measured by single fiber fragmentation test (SFFT).     

Role of potassium permanganate and urea on the improvement of the mechanical properties of jute polypropylene composites

Jute fabrics (hessian cloth) reinforced polypropylene (PP) matrix composites (45 wt% fiber) were fabricated by compression molding. Jute fabrics were treated with 2-hydroxyethyl methacrylate (HEMA) using ultraviolet radiation in order to improve the mechanical properties of the composites. Concentration of HEMA, soaking time and radiation dose were optimized. It was found that 15% HEMA in methanol along with photoinitiator Darocur-1173 (2 %), 10 min soaking time and 20th pass of radiation rendered better performance. Urea of different concentrations (0.5–2 %) was incorporated with 15 % HEMA to monitor its effect on the properties and 1 % urea revealed the best results. For the improvement of the properties, jute fabrics were treated with potassium permanganate (KMnO₄) solution in acetone of different concentrations (0.02, 0.03, 0.05, and 0.5 %) at different soaking times (1, 2, 3, and 5 min) before the composite fabrication. Optimized jute fabrics (jute fabrics treated with 0.03 % KMnO₄) were again treated with HEMA (15 %) solution along with urea (1 %) and promising improvement of mechanical properties of the composites was observed. Scanning electron microscopy, water uptake, soil degradation and thermal aging of the treated and untreated composites were also performed.     

Impact properties of glass-fiber/polypropylene composites: The influence of fiber loading, specimen geometry and test temperature

Glass fiber reinforced polypropylene composites were compounded with a twin-screw extruder and injection molded. Fiber length distribution study showed that more fiber degradation occurred during processing of the composites with higher fiber loading. Dynamic mechanical analysis carried out showed that magnitudes of storage and loss modulus of composites are improves with the presence of the glass fiber in the system. The incorporation of fibers into the composites has slightly shifted the glass transition temperature to lower values. On the other hand, the presence of the glass fiber reduces the magnitude of tan δ at α-transition dramatically due to the strengthening effect by the fibers. From impact test, it was found that increment in glass fiber loading leads to an increase in peak load, critical strain energy release rate and critical stress intensity factor indicating the improvement in the material toughness. However, there was no significant change observed in fracture energy. With respect to increasing in specimen geometry, despite an improvement in peak load and fracture energy of the impact specimen, the critical strain energy release rate and critical stress intensity factor values were decreased. On the other hand, increase in test temperature resulted in reduction of peak load and critical stress intensity factor due to increment in material ductility, whereby fracture energy and critical strain energy release rate improved.     

Effect of kenaf and EFB fiber hybridization on physical and thermo-mechanical properties of PLA biocomposites

Kenaf/empty fruit bunch/polylactic acid (kenaf/EFB/PLA) hybrid biocomposites were prepared using hot press technique. The ratio of fiber to polylactic acid was set at 60:40 with 1:1 ratio between kenaf and empty fruit bunch fibers. Physical, mechanical and thermal properties of hybrid biocomposites were subsequently characterized using Fourier transform infrared spectroscopy, scanning electron microscope, X-ray diffraction, thermogravimetric analysis, differential scanning calorimetry, tensile and water absorption tests. Test results indicated that mechanically stronger fiber was able to support the weaker fiber. Hybrid fiber biocomposite had higher crystallinity as compared to single fiber biocomposite. Water absorption of hybrid composite was higher as compared to single fiber composite. Thermal result revealed that hybridization of fiber was not significantly influence the thermal properties of composites. However, the presence of two different fibers proposed good wettability properties, which could reduce the formation of voids at the fibers-polymer interface and produce composites with high stiffness and strength.     

Physical and mechanical properties of jute, bamboo and coir natural fiber

A systematic study has been carried out to investigate the mechanical and physical properties of jute, bamboo and coir (brown and white) single fibers. The tensile properties (tensile strength, Young’s modulus and strain to failure) were determined by varying span length. Scanning electron microscopic analysis was also carried out to determine the physical properties of fibers in order to correlate with its strength, Young’s modulus and strain to failure. The Young’s modulus and strain to failure were corrected using newly developed equations. The study revealed that with increasing test span length the Young’s modulus increased and tensile strength as well as strain to failure decreased. This is because no extensometer could be used in this test set-up and machine displacement (denoted by α) was used for the modulus determination. It is also attributed that larger span length helps to minimize the machine displacement compared to smaller ones due to the reduced relative effect of slippage in the clamps. Among all fibers, the Young’s modulus of bamboo fiber was the highest. Jute fiber had smoother surface compared to other three examined fibers.     

Surface treatments of jute fabric: The influence of surface characteristics on jute fabrics and mechanical properties of jute/polyester composites

In this study, jute fabrics were modified by alkali, micro-emulsion silicon (MS) and fluorocarbon based agents (FA) in order to enhance the interfacial adhesion between the polyester matrix and the jute fiber. X-ray photoelectron spectroscopy (XPS) and contact angle measurements were used to characterize fiber surfaces. The effects of various surface treatments on the mechanical and morphological of jute/polyester composites were also studied. All surface treatments were shown to improve the tensile, flexural strengths and interlaminar shear strengths of the composites. Moreover, the maximum improvement in the mechanical properties was obtained for the FA treated jute/polyester composites. SEM micrographs of the tensile fracture surface of jute/unsaturated polyester composites also exhibited improvement of interfacial and interlaminar shear strengths by the alkali, MS and FA treatments of jute fibers.     

Improvement in mechanical properties of aluminum polypropylene composite fiber

Aluminum particles (Al) were added to polypropylene (PP) in the presence of poly ethylene glycol (PEG) and polypropylene-graft-maleic anhydride to produce composites. The composites were then melt-spun into a mono filament and tested for tensile properties, diameter evenness and morphology. Melt rheological properties of Al/PP composites were studied in linear viscoelastic response regions. It was observed that level of dispersion of aluminum particles within a polypropylene composite fiber could be improved by incorporating polyethylene glycol. The improvement of dispersion led to an improvement in the fibers mechanical properties through a reduction of the coefficient of variation of fiber diameter.     

Effect of polypropylene fiber cross sectional shapes on some structural/mechanical fiber properties and compressibility behaviour of plain knitted fabrics

Synthetic fibers are generally produced with circular cross sectional shapes. Other cross sectional shaped fibers such as trilobal, triangular, hollow and pentagonal fibers are also produced to improve some properties of fibers and fabrics such as lustre, handle, wicking rate, strength, stiffness and bulkiness. In this research we aimed to investigate compressional behaviours of fabrics knitted from polypropylene fibers having three different cross sectional shapes; namely circular, trilobal and triangular. Morphological, structural and mechanical properties of produced fibers were evaluated by using scanning electron microscopy, X-ray diffractometry, differential scanning calorimetry and tensile tester, respectively. In terms of structural and mechanical properties, no significant differences were found related to fiber cross sectional shapes. Then, plain knitted farbrics were produced and compressional properties of these fabrics were investigated. Fabrics knitted from trilobal fibers showed the highest compressibility properties and it is followed by fabrics which are produced from triangular and circular fibers.     

Effect of water and fiber length on the mechanical properties of polypropylene matrix composites

This paper presents the results of a current study on polypropylene matrix composites processed by injection, with two different glass fiber lengths and five different volume fractions. Physical and mechanical properties were obtained, namely flexural strength, stiffness modulus and fracture toughness. The mechanical properties of the composites increased significantly with the increase of the fibers volume fraction in agreement with the Counto model. The effect of water immersion time was also analysed. Immersion in water promotes a marked decrease in mechanical properties in the early seven-ten days, and afterwards tends to stabilize. Water causes a decrease of the relative strength which increases with fiber volume fraction and reaches about 29 % and 32 % for 20 % of 4.5 mm fiber length and for 25 % of 12 mm fiber length respectively, after 28 days immersion in water. Fracture toughness increases with fiber volume fraction and is always higher for 12 mm fiber length composites than for 4.5 mm fiber length composites.     

The mechanical properties of polyurethane foam wound dressing hybridized with alginate hydrogel and jute fiber

The purpose of this study is to fabricate a smart wound dressing by hybridizing hydrophilic polyurethane foam (PUF) and alginate hydrogel. Hydrophilic PUF is used to maintain damaged tissue in a moist environment. Despite its many strong points as a wound dressing, hydrophilic PUF cannot be loaded with ingredients such as growth factors and cytokines that would enhance wound healing. Therefore, we introduce a pH-sensitive alginate hydrogel with the ability to selectively release drugs within the pH range of wounded skin. Due to the small pore size of PUF and the high viscosity of the alginate solution, the two are not easily penetrable. As such, a vacuum method is used to insert alginate hydrogel into the PUF. The optimum conditions for the vacuum method chosen are to be proposed. However, the mechanical strength of PUF decreased after containing alginate hydrogel. Therefore, Na-alginate powder for PUF, various types of crosslinking agents and jute fiber for alginate hydrogel were introduced to improve the mechanical properties of hydrogel/PUF hybrid wound dressing. Three different types of crosslinking agents are used for the gel formation. The most suitable crosslinking agent and its concentration for alginate hydrogel is also determined by the experiments. The experimental results are discussed with proper schemes and reasonable explanations.     

Evaluation of mechanical properties of jute/glass/carbon fibers reinforced hybrid composites

A study on the tensile and flexural properties of jute-glass-carbon fibers reinforced epoxy hybrid composites in inter-ply configuration is presented in this paper. Test specimens were manufactured by hand lay-up process and their tensile and flexural properties were obtained. The effects of the hybridization, different fibers content and plies stacking sequence on the mechanical properties of the tested hybrid composites were investigated. Two-parameter Weibull distribution function was used to statistically analyze the experimental results. The failure probability graphs for the tested composites were drawn. These graphs are important tools for helping the designers to understand and choose the suitable material for the required design and development. Results showed that the hybridization process can potentially improve the tensile and flexural properties of jute reinforced composite. The flexural strength decreases when partial laminas from a carbon/epoxy laminate are replaced by glass/epoxy or jute/epoxy laminas. Also, it is realized that incorporating high strength fibers to the outer layers of the composite leads to higher flexural resistance, whilst the order of the layers doesn’t affect the tensile properties.     

Mechanical and water absorption properties of woven jute/banana hybrid composites

This work aims to predict the mechanical properties of woven jute/banana hybrid composite. Woven fabrics are arranged in three layers of different sequence. Resin used in this work is Epoxy LY556 with hardener HY951. Composite specimen are prepared by hand-layup techniques. The effect of layering sequence on the mechanical properties namely tensile, flexural and impact was analysed. It is found that the tensile and flexural strength of hybrid composite (Banana/Jute/Banana) is higher than that of individual composites. Similarly, the impact strength of Jute/Banana/Jute hybrid composite is better than other types of composite. It is found that the moisture absorption of woven banana fiber composite is lesser than the hybrid composite. Fractography study of the fractured specimen is carried out using scanning electron microscope to analyse the fracture behaviour of the hybrid composite.     

Effect of mercerization on mechanical, thermal and degradation characteristics of jute fabric-reinforced polypropylene composites

Jute fabric reinforced polypropylene composites were fabricated by compression molding technique. Fiber content in the composites was optimized at 45 % by weight of fiber by evaluating the mechanical parameters such as tensile strength, tensile modulus, bending strength, bending modulus. Surface treatment of jute fabrics was carried out by mercerizing jute fabrics with aqueous solutions of NaOH (5, 10 and 20 %) at different soaking times (30, 60 and 90 mins) and temperatures (0, 30 and 70 °C). The effect of mercerization on weight and dimension of jute fabrics was studied. Mechanical properties of mercerized jute-PP composites were measured and found highest at 20 % NaOH at 0 °C for 60 min soaking time. Thermal analytical data from thermogravimetric and differential thermal analysis showed that mercerized jute-PP composite achieved higher thermal stability compared to PP, jute fabrics and control composite. Degradation characteristics of the composites were studied in soil, water and simulated weathering conditions. Water uptake of the composites was also investigated.     

Hybrid effect in the mechanical properties of jute/rockwool hybrid fibres reinforced phenol formaldehyde composites

This research work was concerned with the evaluation of the effect of fibre content on the mechanical properties of composites. Composites were fabricated using jute/phenol formaldehyde (PF), rockwool/PF, and jute/rockwool hybrid PF with varying fibre loadings. Jute and rockwool fibre reinforced PF composites were fabricated with varying fibre loadings (16, 25, 34, 42, 50, and 60 vol.%). The jute/rockwool hybrid PF composites were manufactured at various ratios of jute/rockwool fibres such as 1:0, 0.92:0.08, 0.82:0.18, 0.70:0.30, 0.54:0.46, 0.28:0.72, and 0:1. Total fibre content of the hybrid composites was 42 vol.%. The results showed that tensile strength of the composite increased with increasing fibre content up to 42 vol.% over which it decreased for jute and rockwool fibre reinforced PF composites. Flexural strength of the composite was noted to peak at a fibre loading of 42 vol.% for jute/PF composites, and 34 vol.% for rockwool/PF composites. Impact strength of jute/PF composites increased with increasing fibre loading but that of rockwool/PF composites decreased at higher (>34 vol.%) fibre loadings. Tensile, flexural, and impact strengths of jute/PF composites were found to be higher than those of rockwool/PF composites. The maximum hardness values were obtained 42 vol.% for jute/PF composite, and 34 vol.% for rockwool/PF composite. Further increase in fibre loading adversely affected the hardness of both composites. For jute/rockwool hybrid PF composites, tensile and impact strengths decreased with increasing rockwool fibre loading. The maximum flexural strength of jute/rockwool hybrid PF composites was obtained at a 0.82:0.18 jute/rockwool fibre ratio while maximum hardness was observed at a 0.28:0.72 jute/rockwool fibre ratio. The fractured surfaces of the composites were analysed using scanning electron microscope in order to have an insight into the failure mechanism and fibre/matrix interface adhesion.     

Effect of the atmospheric plasma treatment parameters on surface and mechanical properties of jute fabric

Plasma treatment is a kind of environmentally friendly surface modification technology, which has been widely used to modify various materials in many industries. Plasma treatment improves the fiber-matrix adhesion largely by roughening the surface of fibers to increase mechanical interlocking between the fiber and the matrix. For this aim, the effect of atmospheric air plasma treatment on jute fabrics has been discussed in this study. The plasma treatment has been employed at different powers and time intervals. The effects of plasma treatment on fiber properties were revealed by wickability, surface roughness, fiber tensile test and pull-out tests. The effect of plasma treatment on functional groups of jute fibers was observed by attenuated total reflectance fourier transform infrared spectroscopy (ATR-FTIR). Scanning electron microscopy (SEM) images showed the etching effect of plasma treatment on the surface. It can be concluded that plasma treatment is an effective method to improve the surface and mechanical properties of jute fabrics to be used for composite materials.