Effect of Various Acids and Sulfites in Steep Solution on Yields and Composition of Corn Fiber and Corn Fiber Oil

The addition of six acids (organic and inorganic) and four sulfite compounds (including gaseous SO₂) during the conventional corn wet‐milling steeping process of two yellow dent corn hybrids were evaluated for the effect on corn fiber yield, corn fiber oil yield, and the composition of three phytosterol compounds (ferulate phytosterol esters [FPE], free phytosterols [St], and phytosterol fatty acyl esters [St:E]) in the corn fiber oil. No significant effect of different sulfite compounds and acids were observed on corn fiber yields. However, a significant effect was observed on corn fiber oil yield and the composition of corn fiber oil for phytosterol compounds. Three of the sulfite compounds (including gaseous SO₂) caused very little effect on the levels of phytosterol compounds compared with the control sample (corn steeped with sodium metabisulfite and lactic acid). However, for one hybrid, ammonium sulfite gave a significantly higher yield of FPE and St:E and had no effect on the yield of St. For the other hybrid, it gave a significantly higher yield of FPE and had no effect on the yield of St and St:E compared with the control sample. This indicates that the effect of these sulfite compounds on yields of these phytosterol compounds in corn fiber oil is probably hybrid‐dependent. No significant effect of acids was observed on corn fiber yields, but significant effects were observed on corn fiber oil yields and yields of phytosterol compounds in the corn fiber oil. The effect also seems to be hybrid‐dependent because different acids affected the two hybrids differently. Overall, it seems that weak acids have a positive effect on increasing the individual phytosterol compounds in the corn fiber. When comparing the effect of experimental acids and sulfites on the two hybrids, acids have a more positive effect than sulfites in increasing the yield of phytosterol compounds in corn fiber oil.     

Comparison of Yield and Composition of Oil Extracted from Corn Fiber and Corn Bran

We recently reported that corn fiber oil contains high levels of three potential cholesterol-lowering phytosterol components: ferulate-phytosterol esters (FPE) (3–6 wt%), free phytosterols (1–2 wt%), and phytosterol-fatty acyl esters (7–9 wt%). A previous study also indicated that corn bran oil contained less phytosterol components than corn fiber oil. The current study was undertaken to attempt to confirm this preliminary observation using more defined conditions. Accordingly, oil was extracted from corn fiber and corn bran prepared under controlled laboratory conditions, using the same sample of corn hybrid kernels for each, and using recognized bench-scale wet-milling, and dry-milling procedures, respectively. After extraction, the chemical composition of the phytosterol components in the oil were measured. This study confirmed our previous observation—that FPE levels were higher in corn fiber oil than in corn bran oil. During industrial wet-milling, almost all of the FPE are recovered in the fiber fraction (which contains both fine and coarse fiber). During laboratory-scale wet-milling, ≈60–70% of the FPE are recovered in the coarse fiber (pericarp) and 30–40% are recovered in the fine fiber. During laboratory-scale dry-milling, <20% of the FPE are recovered in the bran (pericarp), and the rest in the grits. The recoveries of the other two phytosterol components (free phytosterols and phytosterol-fatty acyl esters) revealed a more complex distribution, with significant levels found in several of the dry- and wet-milled products.     

Recovery of Fiber in the Corn Dry-Grind Ethanol Process: A Feedstock for Valuable Coproducts

A new process was developed to recover corn fiber from the mash before fermentation in dry-grind ethanol production. In this process, corn is soaked in water (no chemicals) for a short period of time and then degermed using conventional degermination mills. In the remaining slurry, corn coarse fiber is floated by increasing the density of the slurry and then separated using density differences. The fiber recovered is called quick fiber to distinguish it from the conventional wet-milled fiber. This study evaluated the percent of quick fiber recovery for a normal yellow dent and high oil corn hybrid. The quick fiber was analyzed for levels of corn fiber oil, levels of ferulate phytosterol esters (FPE) and other valuable phytosterol components in the oil and compared with conventional wet-milled corn coarse and fine fiber samples. Fiber samples were also analyzed and compared for yields of potentially valuable corn fiber gum (CFG, hemicellulose B). Comparisons were made between the quick fiber samples obtained with and without chemicals in the soakwater. An average quick fiber yield of 6–7% was recovered from the two hybrids and represented 46–60% of the total fiber (fine and coarse) that could be recovered by wet-milling these hybrids. Adding steep chemicals (SO₂ and lactic acid) to the soakwater increased the quick fiber yields, percent of FPE recoveries, and total percent of phytosterol components to levels either comparable to (for the dent corn hybrid) or higher than (for the high oil corn hybrid) those recovered from the total conventional wet-milled fiber samples. CFG yields in the quick fiber samples were comparable to those from the wet-milled fiber samples. CFG yields in the quick fiber samples were not significantly affected by the addition of chemicals (SO₂ and lactic acid) to the soakwater.     

Effect of Alternative Milling Techniques on the Yield and Composition of Corn Germ Oil and Corn Fiber Oil

The effects of alternative corn wet‐milling (intermittent milling and dynamic steeping (IMDS), gaseous SO₂ and alkali wet‐milling) and dry grind ethanol (quick germ and quick fiber with chemicals) production technologies were evaluated on the yield and phytosterol composition (ferulate phytosterol esters, free phytosterols, and fatty acyl phytosterol esters) of corn germ and fiber oil and compared with the conventional wet‐milling process. Small but statistically significant effects were observed on the yield and composition of corn germ and fiber oil with these alternative milling technologies. The results showed that the germ and fiber fractions from two of the alternative wet‐milling technologies (the gaseous SO₂ and the IMDS) had, for almost all of the individual phytosterol compounds, either comparable or signficantly higher yields compared with the conventional wet‐milling process. Also, both of the modified dry grind ethanol processes (the quick germ and quick fiber) with chemicals (SO₂ and lactic acid) can be used as a new source of corn germ and fiber and can produce oils with high yields of phytosterols. The alkali wet‐milling process showed significantly lower yields of phytosterols compounds in germ but showed significantly higher yield of free phytosterols, fatty acyl phytosterol esters and total phytosterols in the fiber fraction.     

Yield and Phytosterol Composition of Oil Extracted from Grain Sorghum and Its Wet‐Milled Fractions

Corn fiber contains an oil with high levels of three potential cholesterol‐lowering phytosterol compounds. Little information is available about the levels and types of phytosterols in sorghum. In this study, phytosterols were evaluated in grain sorhgum and its wet‐milled fractions and were compared with the phytosterols in corn. The study showed that sorghum kernels can provide a significant source of two phytosterol classes, free phytosterols (St) and fatty acyl phytosterol esters (St:E). Most of these phytosterols are concentrated in the wet‐milled fiber fraction followed by the germ fraction. In addition to phytosterols, other lipid classes such as wax esters and an aldehyde (50% C28 and 50% C30) are also present in the sorghum oil. Comparison of sorghum and corn kernels show that corn has 72–93% more phytosterols than sorghum.     

Pretreatment of Wet‐Milled Corn Fiber to Improve Recovery of Corn Fiber Oil and Phytosterols

The phytosterol‐containing oil in the corn fiber (corn fiber oil) has potential use as a natural low‐density lipoprotein (LDL) lowering nutraceutical but its low concentration (1–3%) makes it difficult and expensive to extract. Pretreatment of corn fiber with dilute acid or glucosidases removed nonlipid components of fiber, producing oil‐enriched fractions that should be more amenable to efficient and inexpensive oil extraction. Acid, as well as enzymes, significantly increased the content of corn fiber oil and its phytosterol compounds by hydrolyzing (and removing) the starch and nonstarch (cell wall) polysaccharides from the wet‐milled corn fiber. Dual treatment of the fiber with acid and enzyme greatly increased the concentrations of corn fiber oil and its phytosterol components, compared with acid or enzyme treatments alone. Depending on the treatment, the oil concentration in the residual solids increased from 0.3 to 10.8% (21–771% increase in conc.) and the total phytosterol concentration increased from 19.8 to 1256.2 mg/g of fiber (11–710% increase in conc.) compared with untreated fiber.     

Comparison of oil and phytosterol levels in germplasm accessions of corn, teosinte, and Job's tears

Seeds of 49 accessions of corn (Zea mays ssp. mays), 9 accessions of teosinte (Zea species that are thought to be ancestors and probable progenitors to corn), and 3 accessions of Job's tears (Coix lacryma), obtained from a germplasm repository, were ground and extracted with hexane. Whole kernel oil yields and levels of four phytonutrients (free phytosterols, fatty acyl phytosterol esters, ferulate phytosterol esters, and gamma-tocopherol) in the oils were measured. Among the seeds tested, oil yields ranged from 2.19 to 4.83 wt %, the levels of ferulate phytosterol esters in the oil ranged from 0.047 to 0.839 wt %, the levels of free phytosterols in the oil ranged from 0.54 to 1.28 wt %, the levels of phytosterol fatty acyl esters in the oil ranged from 0.76 to 3.09 wt %, the levels of total phytosterols in the oil ranged from 1.40 to 4.38 wt %, and the levels of gamma-tocopherol in the oil ranged from 0.023 to 0.127 wt %. In general, higher levels of all three phytosterol classes were observed in seed oils from accessions of Zea mays ssp. mays than in seed oils from accessions of the other taxonomic groups. The highest levels of gamma-tocopherol were observed in teosinte accessions.     

Phytosterol and tocopherol components in extracts of corn distiller's dried grain

As the ethanol industry continues to grow, it will become very important to develop value-added markets for its coproducts in order for the industry to remain profitable. Corn distiller's dried grain (DDG) is a major coproduct of ethanol fermentation from corn processed by dry-milling and is primarily sold as livestock feed. The objective of this research was to determine if valuable phytochemicals found in corn oil and corn fiber oil, such as phytosterols and their saturated equivalents, phytostanols, ferulate phytosterol esters (FPE), tocopherols, and tocotrienols, are retained in DDG. Hexane and supercritical carbon dioxide (CO2) extracts of DDG were similar in their concentrations of total phytosterols (15.8-17.3 mg/g of extract), FPE (3.75-3.99 mg/g of extract), and tocols (1.7-1.8 mg/g of extract). Ethanol extracts were slightly lower in concentration of phytosterols (8.9-11.4 mg/g of extract), FPE (1.62-1.98 mg/g of extract), and tocols (0.73-0.76 mg/g of extract).     

Effects of Amylose,Corn Protein,and Corn Fiber Contents on Production of Ethanol from Starch‐Rich Media

The effects of amylose, protein, and fiber contents on ethanol yields were evaluated using artificially formulated media made from commercial corn starches with different contents of amylose, corn protein, and corn fiber, as well as media made from different cereal sources including corn, sorghum, and wheat with different amylose contents. Second‐order response‐surface regression models were used to study the effects and interactions of amylose, protein, and fiber contents on ethanol yield and conversion efficiency. The results showed that the amylose content of starches had a significant (P < 0.001) effect on ethanol conversion efficiency. No significant effect of protein content on ethanol production was observed. Fiber did not show a significant effect on ethanol fermentation either. Conversion efficiencies increased as the amylose content decreased, especially when the amylose content was >35%. The reduced quadratic model fits the conversion efficiency data better than the full quadratic model does. Fermentation tests on mashes made from corn, sorghum, and wheat samples with different amylose contents confirmed the adverse effect of amylose content on fermentation efficiency. High‐temperature cooking with agitation significantly increased the conversion efficiencies on mashes made from high‐amylose (35–70%) ground corn and starches. A cooking temperature of ≥160°C was needed on high‐amylose corn and starches to obtain a conversion efficiency equal to that of normal corn and starch.     

Hybrid-Dependent Effect of Lactic Acid on Corn Starch Yields

The effect of lactic acid on starch yields of different corn hybrids was determined by wet-milling 18 commercial corn hybrids at three levels of lactic acid. All 18 hybrid samples tested had higher starch yields when lactic acid was added to the steep solution, although the magnitude of the increased starch yields varied between 2.9 and 12.0%. The optimal lactic acid concentration for maximum starch recovery was found to be between 0.55 and 1.67% lactic acid, by wet-milling nine of the same 18 corn hybrids with seven levels of added lactic acid. Between 0.83 and 1.67% lactic acid, the starch yields of eight of the nine hybrids were constant (within ±0.5%). Results showed that the average starch yield across all hybrids decreased with a lactic acid concentration <0.55% and a lactic acid concentration >1.67%.     

Phase transitions, solubility, and crystallization kinetics of phytosterols and phytosterol-oil blends

The thermal properties, solubility characteristics, and crystallization kinetics of four commercial phytosterol preparations (soy and wood sterols and stanols) and their blends with corn oil were examined. Differential scanning calorimetry (DSC) revealed narrow melting peaks between 138 and 145 degrees C for all phytosterol samples, reversible on rescan. Broader and less symmetrical melting transitions at lower temperatures with increasing oil content were observed for two samples of phytosterol-oil admixtures. The estimated, from the solubility law, deltaH values (34.7 and 70.7 mJ/mg for wood sterols and stanols, respectively), were similar to the DSC experimental data. Fatty acid esters of soy stanols differing in the chain length of the acyl groups (C2-C12) exhibited suppression of the melting point and increase of the fusion enthalpy with increasing chain length of the acyl group; the propionate ester exhibited the highest melting point (Tm: 151 degrees C) among all stanol-fatty acid esters. Solubility of phytosterols in corn oil was low (2-3% w/w at 25 degrees C) and increased slightly with a temperature rise. Plant sterols appeared more soluble than stanols with higher critical concentrations at saturation. The induction time for recrystallization of sterol-oil liquid blends, as determined by spectrophotometry, depended on the supersaturation ratio. The calculated interfacial free energies between crystalline sediments and oil were smaller for sterol samples (3.80 and 3.85 mJ/m2) than stanol mixtures (5.95 and 6.07 mJ/m2), in accord with the higher solubility of the sterol crystals in corn oil. The XRD patterns and light microscopy revealed some differences in the characteristics among the native and recrystallized in oil phytosterol preparations.     

Pericarp Fiber Separation from Corn Flour Using Sieving and Air Classification

In the dry‐grind process, starch in ground corn (flour) is converted to ethanol, and the remaining corn components (protein, fat, fiber, and ash) form a coproduct called distillers dried grains with solubles (DDGS). Fiber separation from corn flour would produce fiber as an additional coproduct that could be used as combustion fuel, cattle feed, and as feedstock for producing valuable products such as “cellulosic” ethanol, corn fiber gum, oligosaccharides, phytosterols, and polyols. Fiber is not fermented in the dry‐grind corn process. Its separation before fermentation would increase ethanol productivity in the fermenter. Recently, we showed that the elusieve process, a combination of sieving and elutriation (air flow), was effective in fiber separation from DDGS. In this study, we evaluated the elusieve process for separating pericarp fiber from corn flour. Corn flour remaining after fiber separation was termed “enhanced corn flour”. Of the total weight of corn flour, 3.8% was obtained as fiber and 96.2% was obtained as enhanced corn flour. Neutral detergent fiber (NDF) of corn flour, fiber, and enhanced corn flour (dry basis) were 9.0, 61.5, and 5.7%, respectively. Starch content of corn flour, fiber, and enhanced corn flour (dry basis) were 68.8, 23.5, and 71.3%, respectively. Final ethanol concentration from enhanced corn flour (14.12% v/v) was marginally higher than corn flour (13.72% v/v). No difference in ethanol yields from corn flour and enhanced corn flour was observed. The combination of sieving and air classification can be used to separate pericarp fiber from corn flour. The economics of fiber separation from corn flour using the elusieve process would be governed by the production of valuable products from fiber and the revenues generated from the valuable products.     

Effect of Corn Milling Practices on Aleurone Layer Cells and Their Unique Phytosterols

Coarse and fine fiber fractions obtained from the corn wet‐milling processes, with and without steeping chemicals (SO₂ and lactic acid), were evaluated microscopically for structure and analytically for recovery of phytosterol compounds from the fiber oil. Microscopic results showed that wet milling, with and without chemicals during steeping, changed the line of fracture between pericarp and endosperm and therefore affected the recovery of the aleurone layer in coarse (pericarp) and fine (endosperm cellular structure) fiber. Analytical results showed that most of the phytosterols and mainly phytostanols in corn fiber are contributed by the aleurone layer. Hand‐dissection studies were performed to separate the two layers that comprise the wet‐milled coarse fiber, the aleurone, and pericarp layer. Analyses revealed that the aleurone contained 8× more phytosterols than the pericarp.     

Comparison of Modified Dry‐Grind Corn Processes for Fermentation Characteristics and DDGS Composition

Three different modified dry‐grind corn processes, quick germ (QG), quick germ and quick fiber (QGQF), and enzymatic milling (E‐Mill) were compared with the conventional dry‐grind corn process for fermentation characteristics and distillers dried grains with solubles (DDGS) composition. Significant effects were observed on fermentation characteristics and DDGS composition with these modified dry‐grind processes. The QG, QGQF, and E‐Mill processes increased ethanol concentration by 8–27% relative to the conventional dry‐grind process. These process modifications reduced the fiber content of DDGS from 11 to 2% and increased the protein content of DDGS from 28 to 58%.     

Ethanol Production from Modified and Conventional Dry‐Grind Processes Using Different Corn Types

Different corn types were used to compare ethanol production from the conventional dry‐grind process to wet or dry fractionation processes. High oil, dent corn with high starch extractability, dent corn with low starch extractability and waxy corn were selected. In the conventional process, corn was ground using a hammer mill; water was added to produce slurry which was fermented. In the wet fractionation process, corn was soaked in water; germ and pericarp fiber were removed before fermentation. In the dry fractionation process, corn was tempered, degerminated, and passed through a roller mill. Germ and pericarp fiber were separated from the endosperm. Due to removal of germ and pericarp fiber in the fractionation methods, more corn was used in the wet (10%) and dry (15%) fractionation processes than in the conventional process. Water was added to endosperm and the resulting slurry was fermented. Oil, protein, and residual starch in germ were analyzed. Pericarp fiber was analyzed for residual starch and neutral detergent fiber (NDF) content. Analysis of variance and Fisher's least significant difference test were used to compare means of final ethanol concentrations as well as germ and pericarp fiber yields. The wet fractionation process had the highest final ethanol concentrations (15.7% v/v) compared with dry fractionation (15.0% v/v) and conventional process (14.1% v/v). Higher ethanol concentrations were observed in fractionation processes compared to the conventional process due to higher fermentable substrate per batch available as a result of germ and pericarp fiber removal. Germ and pericarp yields were 7.47 and 6.03% for the wet fractionation process and 7.19 and 6.22% for the dry fractionation process, respectively. Germ obtained from the wet fractionation process had higher oil content (34% db) compared with the dry fractionation method (11% db). Residual starch content in the germ fraction was 16% for wet fractionation and 44% for dry fractionation. Residual starch in the pericarp fiber fraction was lower for the wet fractionation process (19.9%) compared with dry fractionation (23.7%).     

Laboratory Wet Milling of Corn: Milling Fraction Correlations and Variations Among Crop Years

Several coproducts result from fractionating corn in the wet‐milling process. Because small changes in product composition and milling characteristics can have a major impact on coproduct yields and values, testing is done to anticipate final product yields. Using small sample size and controlled conditions, a laboratory wet‐milling method proved to be a useful tool for wet milling and genetics industries. A wet‐milling process (100‐g batches) was used for data collection. Data collected during 11 years (1994–2004) were observed for samples used as benchmarks to verify process precision and accuracy and determine correlations among wet‐milling yields. More than 400 milling tests were performed on benchmark samples. Data from benchmark samples also were pooled. Coefficients of variation were low (<6%) for mean yields; year‐to‐year standard deviations of benchmark sample yield means were homogenous and implied precision of the procedure. Some differences were detected in mean yields among years (P ≤ 0.05) for benchmark data due to combined effects of hybrid and environment. A negative correlation (r = –0.58) was observed between starch and gluten yield for pooled benchmark data. Four years (2002–2005) of milling data from commercially available hybrids were analyzed using the milling procedure. For pooled commercial data, the correlation between starch and fiber yield was (r = –0.80); correlation between starch and gluten was (r = –0.76).     

Effect of heat pretreatment on the yield and composition of oil extracted from corn fiber.

Previously, hexane extraction of corn fiber was reported to produce a unique and potentially valuable oil that contained high levels of several phytosterols (which have been noted for their cholesterol-lowering properties). Current studies revealed that heat treatment (over the range of 100-175 degrees C) of corn fiber in either a convection oven or a vacuum oven caused only a modest reduction in the levels of the phytosterol components. However, these same heat pretreatments caused a considerable increase (up to 10-fold) in the levels (increasing from 0.34 wt % to a maximum of 3.64 wt % gamma-tocopherol in the oil) and yields (increasing from 5.4 mg of gamma-tocopherol/100 g of corn fiber to a maximum of 52.1 mg of gamma-tocopherol/100 g of corn fiber) of gamma-tocopherol in corn fiber oil. The main differences between the convection oven and vacuum oven pretreatments were associated with the disappearance of free fatty acids and free phytosterols at the higher temperature pretreatments in the vacuum oven, probably due to the lower boiling points of these lipids. Microwave pretreatment was also effective but caused a much smaller increase in the levels of gamma-tocopherol.     

Comparison of Laboratory and Pilot-Plant Corn Wet-Milling Procedures

One waxy and three regular yellow dent corn hybrids were wet milled by using two scales of laboratory procedures (modified 100-g and 1-kg) and a pilot-plant procedure (10-kg). The modified 100-g and 1-kg laboratory procedures gave similar yields of wet-milling fractions. Starch yields and recoveries were significantly lower for the pilot-plant procedure, whereas gluten and fiber yields were greater because of their high contents of unrecovered starch. Protein contents of the starches obtained by all three procedures were within commercially acceptable limits (<0.50% db for normal dent corn and <0.30% for waxy corn). Rankings for starch yields and starch recoveries for the four hybrids, having very different physical and compositional properties, were the same for all three procedures. The harder the grain, the lower the yield and recovery of starch. Least significant differences (P < 0.05) for starch yield were 0.8% for the modified 100-g procedure, 1.2% for the 1-kg procedure, and 2.0% for the pilot-plant procedure.     

Influence of Stenocarpella maydis Infected Corn on the Composition of Corn Kernel and Its Conversion into Ethanol

Widespread epidemics of Stenocarpella ear rot (formerly Diplodia ear rot) have occurred throughout the central U.S. Corn Belt in recent years, but the influence of S. maydis infected grain on corn ethanol production is unknown. In this study, S. maydis infected ears of variety Heritage 4646 were hand‐harvested in 2010 from a production field in central Illinois and segregated into one of five levels of ear rot severity based upon visual symptoms. The concentration of ergosterol, a sterol produced by fungi but not plants, was observed to increase with the severity of ear rot (127–306.5 μg/g), and none was detected in the control corn. Corn test weight declined with progression of the disease and was 42.6% lower for the most severely rotted grain from ears infected early in their development. Accompanying changes in composition were also apparent. Crude fat and oil contents decreased (from 4.7 to 1.5%) and fiber increased (from 6.6 to 9.6%), but starch content remained largely invariant. Oil composition also varied among the infected samples. Control and infected corn samples were subjected to ethanol fermentation with a laboratory‐scale corn dry‐grind ethanol process. Ethanol yields for control and infected samples were similar on an equivalent weight basis (2.77–2.85 gal/bu). In comparison with the control, S. maydis infection altered the distillers dried grains with solubles (DDGS) properties, wherein the crude protein was significantly higher and oil significantly reduced, and ash, fiber, and yield per ton were not significantly different. Based upon these results, we conclude that Stenocarpella ear rot has the potential to affect DDGS composition but not ethanol yield on an equivalent weight basis.     

Comparison of Alkali and Conventional Corn Wet-Milling: 1-kg Procedures

An alkali corn wet-milling process was developed to evaluate the process as a method to produce high purity corn starch and coproducts with added value. Using a single hybrid (R1064 × LH59), the effects of alkali concentration (0.18–0.82% NaOH), time (29–61 min), and temperature (36–75°C) were investigated. Starch yield was not affected by steep time or temperature. Starch yield was optimal at 65.2% using 0.5% alkali. Increasing the concentration of alkali to 0.82% or decreasing it to 0.18% caused a decrease in starch yield of 8–10 percentage points. Other wet-milling products (fiber, germ, and gluten) also were affected. Steep conditions of 0.5% NaOH, 60 min, and 45°C gave optimal starch yield. Comparisons between alkali and sulfur dioxide wet-milling processes, using 1-kg sample size, were performed on 10 commercial yellow dent corn hybrids. The alkali process averaged 1.7 percentage points more starch than the sulfur dioxide process. Each hybrid had a higher starch yield when wet-milled with the alkali method. Alkali wet-milling produced pure corn starch with <0.30% protein (db).