Determination of the hop-derived phytoestrogen, 8-prenylnaringenin, in beer by gas chromatography/mass spectrometry

A method was developed to determine 8-prenylnaringenin, a novel hop-derived phytoestrogen, in beer. Matrix purification involved solid-phase extraction on octadecyl silica followed by liquid/liquid extraction on a ChemElut 1010 column connected to a Florisil adsorption/desorption cartridge. 8-Prenylnaringenin was eluted from the tandem columns using a 1:1 mixture of diethyl ether and ethyl acetate and subsequently determined as tris(trimethylsilyl) ether by GC/MS-SIM. The recovery of 8-prenylnaringenin in beer samples was between 61.1 +/- 6.6 and 82.2 +/- 8.8% for levels of 37 and 92.5 microg L(-1), respectively, and the detection limit was approximately 5 microg L(-1). Although most beers do not contain 8-prenylnaringenin in detectable quantities, the highest concentration found was 19.8 microg L(-1). The concentration of 8-prenylnaringenin in beers and, possibly, its absence depend on the selection of particular hop varieties, the hopping rate, or the type of hop product used in brewing. The efficiency of transfer of 8-prenylnaringenin from hops to beer is between 10 and 20%.     

Steviol quantification at the picomole level by high-performance liquid chromatography

A simple and highly sensitive reversed-phase high-performance liquid chromatographic method (RP-HPLC) has been developed for the determination of steviol (SV) using dihydroisosteviol (DHISV) as an internal standard (IS). SV and DHISV were derivatized by reaction of the acids with 4-(bromomethyl)-7-methoxycoumarin in an aprotic solvent (DMF or acetone). The resulting ester derivatives were separated on an ODS column (250 x 4.6 mm i.d., 5 microm particle size) using fluorescence detection with excitation at 321 nm and emission at 391 nm. The mobile phase consisted of acetonitrile/water (80:20 v/v) with a flow rate of 1 mL min(-)(1). A linear relationship was observed for concentrations between 0.5 and 50 microg/mL of SV, and the detection limit was 100 pg. For application of this method to samples of beer fortified with stevioside, a simple procedure for extraction of the beer with diethyl ether and derivatization in DMF was applied. Whereas beer samples spiked with SV gave a linear response over the range 0.1-15 microg/mL beer, no SV could be detected in beer samples enriched in stevioside that had been stored for over 3 years. The application of the method to plant samples involved preparation of an acid fraction containing the SV analyte, derivatization, and sample cleanup using small silica columns and thin-layer chromatography. A sensitive determination of 594 ng of steviol present in 100 mg of dry plant material was performed with high precision and accuracy.     

Determination of low levels of perchlorate in lettuce and spinach using ion chromatography-electrospray ionization mass spectrometry (IC-ESI-MS)

A sample preparation method was developed to quantify environmentally relevant (low micrograms per liter) concentrations of perchlorate (ClO4(-)) in leafy vegetables using IC-ESI-MS. Lettuce and spinach were macerated, centrifuged, and filtered, and the aqueous extracts were rendered water-clear using a one-step solid-phase extraction method. Total time for extraction and sample preparation was 6 h. Ion suppression was demonstrated and was likely due to unknown organics still present in the extract solution after cleanup. However, this interference was readily eliminated using a Cl(18)O4(-) internal standard at 1 microg/L in all standards and samples. Hydroponically grown perchlorate-free butterhead lettuce was spiked to either 10.3 or 37.7 microg/kg of fresh weight (FW), and recoveries were between 91 and 98% and between 93 and 101%, respectively. Five types of lettuce and spinach from a local grocery store were then analyzed; they contained from 0.6 to 6.4 microg/kg of FW. Spike recoveries using the store-bought samples ranged from 89 to 100%. The method detection limit for perchlorate in plant extracts is 40 ng/L, and the corresponding minimum reporting limit is 200 ng/L or 0.8 microg/kg of FW.     

Assay of ochratoxin A in wine and beer by high-pressure liquid chromatography photodiode array and gas chromatography mass selective detection.

To routinely assay the concentrations of ochratoxin A (OTA) in wines and beers, two new methods were developed and evaluated. The first utilized solid-phase extraction on a C(18) cartridge to achieve a 100-fold sample concentration followed by high-performance liquid chromatography on a C(18) column with gradient elution and quantitation at 333 nm by means of a photodiode array detector. Positive confirmation can be carried out by purity and match-factor analysis as well as peak shift following esterification with BF(3). Total run time is 28 min. The limits of detection (LOD) and quantitation (LOQ) are 0.05 and 0.10 microg/L, respectively. Recovery and imprecision ranged from 83 to 94% and from 4.0 to 8.9%, respectively. With a throughput of 35 assays per working day, this method is ideal for routine OTA analysis. It was used to survey the concentrations of OTA in 942 wines (2 of which gave values between 0.1 and 0.2 microg/L) and 107 beers (2 of which gave values between 0.05 and 0.1 microg/L). OTA was detected more frequently in red than white wines, with the highest incidence in red wines from Spain and Argentina. There was no association between OTA and country of origin or beverage type among the beers analyzed. The second method utilized gas chromatography with mass selective detection monitoring eight specific ions, preceded by extraction in dichloromethane and derivatization with bis[trimethylsilyl]trifluoroacetamide. LOD and LOQ were 0.1 and 2 microg/L, respectively; recovery and imprecision were 69-75 and 9.0-11.1%, respectively. The method is not suitable for routine quantitation but is potentially useful as a confirmatory tool for samples with OTA > or =0.1 microg/L.     

ELISA for sulfonamides and its application for screening in water contamination

Two enzyme-linked immunosorbent assays (ELISAs) were tested for their suitability for detecting sulfonamides in wastewater from various stages in wastewater treatment plants (WWTPs), the river into which the wastewater is discharged, and two swine-rearing facilities. The sulfamethoxazole ELISA cross-reacts with several compounds, achieving detection limits of <0.04 microg/L for sulfamethoxazole (SMX), sulfamethoxypyridine, sulfachloropyridine, and sulfamethoxine, whereas the sulfamethazine (SMZ) ELISA is more compound specific, with a detection limit of <0.03 microg/L. Samples from various stages of wastewater purifications gave 0.6-3.1 microg/L by SMX-ELISA, whereas river samples were approximately 10-fold lower, ranging from below detection to 0.09 microg/L. Swine wastewater samples analyzed by the SMX-ELISA were either at or near detectable limits from one facility, whereas the other facility had concentrations of approximately 0.5 microg/L, although LC-MS/MS did not confirm the presence of SMX. Sulfamethazine ELISA detected no SMZ in either WWTP or river samples. In contrast, wastewater samples from swine facilities analyzed by SMZ-ELISA were found to contain approximately 30 microg/L [piglet (50-100 lb) wastewater] and approximately 7 microg/L (market-weight hog wastewater). Sulfamethazine ELISA analyses of wastewater from another swine facility found concentrations to be near or below detection limits. A solid phase extraction method was used to isolate and concentrate sulfonamides from water samples prior to LC-MS/MS multiresidue confirmatory analysis. The recoveries at 1 microg/L fortification ranged from 42 +/- 4% for SMZ to 88 +/- 4% for SMX ( n = 6). The ELISA results in the WWTPs were confirmed by LC-MS/MS, as sulfonamide multiresidue confirmatory analysis identified SMX, sulfapyridine, and sulfasalazine to be present in the wastewater. Sulfamethazine presence at one swine-rearing facility was also confirmed by LC-MS/MS, demonstrating the usefulness of the ELISA technique as a rapid and high-throughput screening method.     

Simple and sensitive determination of o-phenylphenol in citrus fruits using gas chromatography with atomic emission or mass spectrometric detection

In this work, a simple and sensitive method for the analysis of the pesticide o-phenylphenol (OPP) on citrus fruits was developed. OPP is extracted with dichloromethane by ultrasonication and derivatized with ferrocenecarboxylic acid chloride. Using ferrocene as a label, residues of OPP are determined by gas chromatography with atomic emission detection in the iron selective mode or with mass spectrometric detection. Sample cleanup is simple and rapid and merely involves a removal of excess reagent on an alumina minicolumn. The method detection limit is 2 ng of OPP/g of fruit, and recoveries from lemon samples fortified at levels of 35 and 140 ng/g are 101 and 106%, respectively. The citrus fruits analyzed (oranges, grapefruits, lemons) contained between 60 ng/g and 0.37 microg/g OPP (RSD = 8-13%), and the results were in good agreement with results obtained when OPP was analyzed using an established HPLC-FLD method. Several alcohols could also be identified in the fruit peel.     

Quantification of ptaquiloside and pterosin B in soil and groundwater using liquid chromatography-tandem mass spectrometry (LC-MS/MS)

The carcinogenic compound ptaquiloside is produced by bracken fern (Pteridium aquilinum L.). Ptaquiloside can enter the soil matrix and potentially leach to the aquatic environment, and methods for characterizing ptaquiloside content and fate in soil and groundwater are needed. A sensitive detection method has been developed using liquid chromatography-tandem mass spectrometry (LC-MS/MS) for analyzing ptaquiloside and its transformation product pterosin B. Detection limits are 0.19 microg/L (ptaquiloside) and 0.15 microg/L (pterosin B), which are 300-650 times better than previously published LC-UV methods. Sequential soil extractions are made using 5 mM ammonium acetate for extraction of ptaquiloside, followed by 80% methanol extraction for pterosin B. Groundwater samples are cleaned-up and preconcentrated by a factor of 20 using solid-phase extraction. The LC-MS/MS method enables quantification of ptaquiloside and pterosin B in soil and groundwater samples at environmentally relevant concentrations and delivers a reliable identification because of the structure-specific detection method.     

Gas chromatographic determination of N-nitrosamines in beverages following automatic solid-phase extraction

A semiautomatic method for the determination of seven N-nitrosamines in beverages by gas chromatography with nitrogen-phosphorus detection is proposed. Beverage samples are aspirated into a solid-phase extraction module for preconcentration and cleanup. The influence of the experimental conditions was examined by using various sorbents among which LiChrolut EN was found to provide quantitative elution and the highest preconcentration factors of all. The proposed method is sensitive, with limits of detection between 7 and 33 ng/kg, and precise, with relative standard deviations from 4.3% to 6.0%. The recoveries of N-nitrosamines from beverage samples spiked with 0.5 or 1 microg/kg concentrations of these compounds ranged from 95% to 102%. The method was successfully applied to the determination of residues of the studied N-nitrosamines in beverages including beer, wine, liquor, whisky, cognac, rum, vodka, grape juice, cider, tonic water, and soft drinks. The analytes were only detected in beer samples, positives being confirmed by gas chromatography coupled with impact ionization mass spectrometry.     

Development of an enzyme-linked immunosorbent assay for the pyrethroid cypermethrin

A competitive enzyme-linked immunosorbent assay (ELISA) for the detection of cypermethrin was developed. Two haptens, the trans- and cis-isomers of 3-[(+/-)-cyano-3-(2,2-dichloroethenyl)-2,2-dimethylcyclopropanecarbonyloxy]methyl]phenoxyacetic acid, were conjugated with thyroglobulin as immunogens. Four antisera were generated and screened against six different coating antigens. The assay that was the most sensitive for cypermethrin was optimized and characterized. The IC(50) for cypermethrin was 13.5 +/- 4.3 microg/L, and the lower detection limit (LDL) was 1.3 +/- 0.5 microg/L. This ELISA had relatively low cross-reactivities with other major pyrethroids, such as deltamethrin, phenothrin, resmethrin, fluvalinate, and permethrin. Methanol was found to be the best organic cosolvent for this ELISA, with an optimal sensitivity observed at a concentration of 40% (v/v). The assay parameters were unchanged at pH values between 5.0 and 8.0, whereas higher ionic strengths strongly suppressed the absorbances. To increase the sensitivity of the overall method, a C(18) sorbent-based solid-phase extraction was applied to various domestic and environmental water samples. The water samples, fortified with cypermethrin, were analyzed according to this method. Good recoveries and correlation with spike levels were observed.     

Enzyme-linked immunosorbent assay for the pyrethroid deltamethrin

A competitive enzyme-linked immunosorbent assay (ELISA) for the detection of deltamethrin was developed. Two haptens, cyano[3-(4-aminophenoxy)phenyl]methyl 1R-cis-3-(2,2-dibromoethenyl)-2,2-dimethylcyclopropanecarboxylate and 3-[(+/-)-cyano[1R-cis-3-(2,2-dibromoethenyl)-2,2-dimethylcyclopropan ecarbonyloxy]methyl]phenoxyacetic acid, were synthesized and conjugated with thyroglobulin as immunogens. Four antisera were generated and screened against six different coating antigens. The assay that was the most sensitive for deltamethrin was optimized and characterized. The I(50) for deltamethrin was 17.5 +/- 3.6 microg/L, and the lower detection limit was 1.1 +/- 0.5 microg/L. This ELISA assay had relatively low cross-reactivities with other major pyrethroids, such as permethrin, phenothrin, bioresmethrin, cyfluthrin, and cypermethrin. Methanol was found to be the best organic cosolvent for this ELISA, with optimal sensitivity observed at a concentration of 40% (v/v). The assay parameters were unchanged at pH values between 5.0 and 8.0, whereas higher ionic strengths strongly suppressed the absorbances. To increase the sensitivity of the overall method, a C(18) sorbent-based solid-phase extraction was used for river water samples. River water samples fortified with deltamethrin were analyzed according to this method. Good recoveries and correlation with spike levels were observed.     

Development of a solid-phase extraction method for phenoxy acids and bentazone in water and comparison to a liquid-liquid extraction method

A rapid solid-phase extraction (SPE) method was developed for the determination of bentazone and the phenoxy acids 2,4-D, dichlorprop, MCPA, and mecoprop in Norwegian environmental water samples. Cartridges with a high-capacity cross-linked polystyrene-based polymer were used for off-line preconcentration. The effects of elution solvent, elution volume, sample volume, sorbent mass, pH, and flow rate on the recoveries of the pesticides were investigated using HPLC. Average recovery of >90% was achieved with 500 mg sorbents using 2 mL of methanol with 5% NH3 as elution solvent. The recoveries were independent of sample pH in the tested range of pH 1-7. Using a sample volume of 200 mL, the limits of determination for the phenoxy acids and bentazone are 0.02 microg/L. Sample volumes up to 2000 mL at a flow rate of 60 mL/min could be handled without any loss of analytes, which makes it possible to lower the limits of determination. The SPE method was compared to a routinely used liquid-liquid extraction method. Three different water matrices spiked at 1.0 and 0.05 microg/L were extracted, and the quantification was performed by GC-MS. Both methods permitted the determination of phenoxy acids and bentazone in distilled water, creek water, and well water down to a level of 0.05 microg/L with recoveries >80% for 200 mL samples. Important advantages of the SPE method compared to the liquid-liquid extraction method were the short extraction times, lack of emulsions, use of disposable equipment, and reduced consumption of organic solvents.     

Determination of Ni (II) in beverages without any sample pretreatment by adsorptive stripping chronopotentiometry (AdSCP)

The purpose of this paper was to use adsorptive stripping chronopotentiometry for the determination of Ni (II) in worldwide consumed beverages without any sample pretreatment, using dimethilglyoxime (DMG) as complexing agent and a glassy carbon mercury film electrode as the working electrode. Ni (DMG)2 complex is adsorbed onto the mercury film at an electrolysis potential of -500 mV for 60 s and then reduced by a -5 microA constant cathodic current. The sensitivity of the method was studied for certified reference water and black tea in the pH range 6.5-11. At pH 9.5 in ammonia buffer, a detection limit of 0.2 microg L(-1) was achieved; the instrumental precision (expressed as rsd %) was 1.5%, and the accuracy, expressed as obtained recoveries both from certified and not certified matrixes, ranged from 93.0 to 95.5 %. The chronopotentiometric analysis executed on commercial beverages provided evidence that black tea samples were the richest source of Ni (II) (1500-3700 microg L(-1)), followed by coffee (100.0-300.5 microg L(-1)); bottled mineral water showed a Ni (II) concentration lower than 4.6 microg L(-1). Among alcoholic beverages, red wines presented the highest content of Ni (II) (55.5-105.0 microg L(-1)). Significant differences were noticed between Ni (II) levels of fermented and distillated alcoholic beverages; moreover, canned cola and beer did not show higher Ni (II) levels with respect to the glass-bottled products.     

Development of an immunoassay for the pyrethroid insecticide esfenvalerate.

A competitive enzyme-linked immunosorbent assay was developed for the detection of the pyrethroid insecticide esfenvalerate. Two haptens containing amine or propanoic acid groups on the terminal aromatic ring of the fenvalerate molecule were synthesized and coupled to carrier proteins as immunogens. Five antisera were produced and screened against eight different coating antigens. The assay that had the least interference and was the most sensitive for esfenvalerate was optimized and characterized. The I(50) for esfenvalerate was 30 +/- 6.2 microg/L, and the lower detection limit (LDL) was 3.0 +/- 1.8 microg/L. The assay was very selective. Other pyrethroid analogues and esfenvalerate metabolites tested did not cross-react significantly in this assay. To increase the sensitivity of the overall method, a C(18) sorbent-based solid-phase extraction (SPE) was used for water matrix. With this SPE step, the LDL of the overall method for esfenvalerate was 0.1 microg/L in water samples.     

Low-temperature brewing using yeast immobilized on dried figs

Dried figs, following exhaustive extraction of their residual sugars with water, were used for immobilization of Saccharomyces cerevisiae AXAZ-1. The immobilized biocatalyst was used in repeated batch fermentations of glucose at 30 degrees C, where significant reduction of the fermentation time was observed, falling from 65 h in the first batch to 7 h after the sixth batch. Repeated fermentations of wort at room and low temperatures resulted in fermentation times that fell from 26 to 20 h and from 27 to 24 days at 18 and 3 degrees C, respectively. Ethanol and beer productivities were high, showing suitability of the biocatalyst for low-temperature brewing. Diacetyl concentrations were low (0.3-0.5 mg/L), and polyphenols were lower than in commercial products and decreased as the fermentation temperature was decreased (126-50 mg/L). Ethyl acetate concentrations increased from 53 to 88 mg/L as the temperature was decreased, while the concentration of amyl alcohols at 3 degrees C (58 mg/L) was lower than half of that at 18 degrees C (125 mg/L). The beers produced at the end of the main fermentation had a fine clarity and a special fruity figlike aroma and taste, distinct from commercial products and more intense than beers produced by cells immobilized on other food-grade supports (gluten pellets or delignified cellulosic materials). GC-MS analysis did not show significant differences in the qualitative composition of the aroma compounds of the beers produced by immobilized and free cells.     

Disposable biosensor test for organophosphate and carbamate insecticides in milk

A highly sensitive and rapid biosensor test based on disposable screen-printed thick-film electrodes was developed, which is suitable for monitoring organophosphate and carbamate residues in foods of animal origin with increased fat contents such as milk. The wild-type enzyme was combined with three engineered variants of Nippostrongylus brasiliensis acetylcholinesterase (NbAChE), to obtain enhanced sensitivity. The sample pretreatment could be reduced to a minimum. There was no extraction or fat removal necessary. With the biosensor test paraoxon concentrations down to 1 microg/L could be detected in milk. The detection limit for carbaryl was 20 microg/L. Recovery rates for paraoxon and carbaryl in milk samples lay between 89 and 107%. Ten milk samples from local markets were tested both with the biosensor test and with standard chromatographic multiresidue methods. Two milk samples caused AChE inhibition rates of >50%. Accordingly, 4 microg/L tebufenpyrad, 4 microg/L tetraconazole, and 2 microg/L bifenthrin were detected in one of these milk samples. The other milk sample contained 2 microg/L tebufenpyrad.     

Application of factorial designs to study factors involved in the determination of aldehydes present in beer by on-fiber derivatization in combination with gas chromatography and mass spectrometry

With the aim of studying the factors involved in on-fiber derivatization of Strecker aldehydes, furfural, and (E)-2-nonenal with O-(2,3,4,5,6-pentafluorobenzyl)hydroxylamine in beer, factorial designs were applied. The effect of the temperature, time, and NaCl addition on the analytes' derivatization/extraction efficiency was studied through a factorial 2(3) randomized-block design; all of the factors and their interactions were significant at the 95% confidence level for most of the analytes. The effect of temperature and its interactions separated the analytes in two groups. However, a single sampling condition was selected that optimized response for most aldehydes. The resulting method, combining on-fiber derivatization with gas chromatography-mass spectrometry, was validated. Limits of detections were between 0.015 and 1.60 μg/L, and relative standard deviations were between 1.1 and 12.2%. The efficacy of the internal standardization method was confirmed by recovery percentage (73-117%). The method was applied to the determination of aldehydes in fresh beer and after storage at 28 °C.     

Quantitation of (R)- and (S)-linalool in beer using solid phase microextraction (SPME) in combination with a stable isotope dilution assay (SIDA)

A stable isotope dilution assay (SIDA) was developed for the quantitation of both linalool enantiomers using synthesized [2H(2)]R/S-linalool as the internal standard. For enrichment of the target compound from beer, a solid phase microextraction method (SPME) was developed. In comparison to the more time-consuming extraction/distillation cleanup of the beer samples, the results obtained by SPME/SIDA were very similar, even under nonequilibration conditions. Analysis of five different types of beer showed significant differences in the linalool concentrations, which were clearly correlated with the intensity of the hoppy aroma note as evaluated by a sensory panel. In addition, significant differences in the R/S ratios were measured in the beers. The SPME/SIDA yielded exact data independently from headspace sampling parameters, such as exposure time or ionic strength of the solution.     

Rapid and sensitive HILIC-ESI-MS/MS quantitation of polar metabolites of acrylamide in human urine using column switching with an online trap column

The carcinogen acrylamide (AA) is formed during the processing of food. AA is metabolized to mercapturic acids, which are excreted with urine. A hydrophilic interaction liquid chromatography tandem mass spectrometry method (HILIC-MS/MS) using a zwitterionic stationary phase (Zic-HILIC) was developed and validated to quantitate the mercapturic acids of AA (AAMA) and glycidamide (GAMA), and AAMA-sulfoxide in human urine. In contrast to reversed phases, the application of Zic-HILIC resulted in efficient retention and separation of these highly polar compounds. Off-line sample workup was avoided by application of column switching with a Stability BS-C17 trap column prior to the analytical column, thus minimizing interferences with the urinary matrix. Limit of quantification values (LOQs) were 0.5 microg/L (AAMA), 2.0 microg/L (AAMA-sulfoxide), and 1.0 microg/L (GAMA) in human urine. Median concentrations in urine samples ( n = 54) of six nonsmoking human subjects were 24.0 microg/L (AAMA, 7.8-79.8 microg/L), 16.7 microg/L (AAMA-sulfoxide, 6.8-70.1 microg/L), and 3.82 microg/L (GAMA, 1.0-23.6 microg/L).     

Acid-induced phase separation of anionic surfactants for the extraction of 1,4-dichlorobenzene from honey prior to liquid chromatography

The acid-induced liquid-liquid phase separation of anionic surfactants in aqueous solutions and its applicability to cloud point extraction methodology were applied as a tool for the extraction of 1,4-dichlorobenzene (p-DCB) from aqueous samples. p-DCB is extracted into the micelles of sodium dodecane sulfonate (SDSA) in a 4.2 M HCl solution. The micellar phase is separated from the bulk aqueous solution after centrifugation and collected from the surface of the suspension. The micellar extracts are injected into a high-performance liquid chromatographic apparatus and quantified at 225 nm with a reference wavelength of 280 nm. Following the proposed methodology, a preconcentration factor of ca. 160 is achieved (starting from 50 mL solutions) allowing for detection limits at the low microg/L level. Application to honey samples produced detection limits of 2.5 microg/kg with quantification limits of 7.5 microg/kg, while the recoveries of the method ranged from 85% at high concentrations to 95% at lower concentrations of p-DCB. The combined uncertainty of the entire analytical procedure was 4.5% at the concentration level of 30 microg/kg allowing for reliable and reproducible results for the determination of p-DCB at the concentration levels considered as thresholds for EU and U.S. legislation (10 microg/kg).     

Dissipation of the herbicide benzofenap (Taipan 300) in a rice field ecosystem

The fate of benzofenap [2-[4-(2,4-dicholoro-m-toluoyl)-1,3-dimethylpyrazol-5-yloxy]-4'-methylacetophenone] applied to flooded rice was studied at two locations in New South Wales (Australia). Solid-phase extraction (SPE) was compared with liquid-liquid extraction (LLE) for the determination of the commercial chemical in water samples. SPE performed well as compared to LLE (84 vs 80%) in irrigation waters. However, at the lower end of the concentration range (3 microg/L), LLE achieved higher recoveries than SPE (72 vs 59%). Rates of dissipation (DT50) from floodwaters and soils were measured. Dissipation of the herbicide from water and soil occurred fairly erratically in both mediums and can be best explained by a first-order decay process. The DT50 value for benzofenap was <1 day in irrigation water due to rapid deposition of the suspension concentrate formulation. The DT50 in surface soil was 44 days. The maximum measured concentration of benzofenap in a rice field floodwater was 39 microg/L, taking approximately 32 days to dissipate to <1 microg/L.