柳杉木材干缩性能指标研究

本文测定了长岭岗林场不同立地条件下23a生柳杉人工林的木材干缩性能指标，进行了不同立地条件下各指标的差异性的F检验。结果表明：在不同立地条件下，柳杉全干径向干缩率和全干体积干缩率存在显著差异(0=0．05)，立地对全干弦向干缩率、差异干缩以及气干干缩指标影响不显著；土层较厚，柳杉干缩率越高，差异干缩则越低。得出了该场柳杉林分木材干缩性能指标的平均水平。     

长岭岗林场日本落叶松幼龄材干缩性能研究

测定了建始县长岭岗林场引种栽培的12年生日本落叶松标准木干缩性能指标，并分析了来自两个样地的20株样木株同差异，其结果表明：干缩性能指标问差异不显著；径向全干干缩率为4．64，弦向全干干缩率为6．81，体积全干干缩率为10．81。全干差畀干缩为1．47；径向气干干缩率为2．41，弦向气干干缩率为3．93，体积气干干缩率为6．59，气干差异干缩为1．63。在此基础上，讨论了日本落叶松的栽培与木材利用中的有关问题和新旧标准下测定的干缩性能指标的换算与利用。     

三倍体毛白杨新无性系木材干缩性的遗传分析

利用 9a生三倍体毛白杨测定林的 9个无性系为试材 ,着重研究了木材干缩率的遗传学问题。结果表明 :木材干缩率在无性系间的差异都达到了极显著水平 ,并受到强度遗传控制 ;木材干缩在株内纵向的变异模式是随树高增加而降低 ;全干体积 ,径向、弦向干缩率和气干体积 ,径向、弦向干缩率无性系重复力分别为 0 89,0 95 ,0 84 ,0 6 7,0 84和 0 6 8。     

10年生火炬松木材28个家系干缩率的变异分析

对10年生火炬松28个家系的6项干缩率指标的统计结果表明：16、24、27、32家系的干缩率较小，可作为建筑材的首选优村家系；家系间整体变异系数较小，家系内个体变异大多很大，在家系基础上进行个体改良效果更好；28个家系的全干干缩率与气干缩率密切相关，在全干和气干状态时，弦、径向干缩率比值T/R亦显著相关。     

6个杨树无性系木材密度及干缩性能差异

以6个杨树无性系木材为研究对象,对杨树的密度及干缩性能进行了分析研究,为杨树木材的加工利用提供依据。结果表明:6个杨树无性系木材基本密度为0.33～0.43 g/cm3,气干密度为0.39～0.51 g/cm3,全干密度为0.37～0.49 g/cm3,密度在不同无性系间差异极显著。50号杨、中林46杨、南杨木材密度沿径向呈逐渐增加的变化趋势,而108杨、N179杨和桑巨杨木材密度呈现先降低后逐渐增加的趋势。杨树无性系木材气干和全干干缩差异均值分别为2.53和2.22,不同无性系间气干干缩率(径向、弦向、体积、干缩差异)和全干干缩率(径向、弦向、体积、干缩差异)差异均极显著。50号杨、N179杨和桑巨杨木材干缩差异沿髓心向外呈现先增加后减小的趋势,中林46杨呈现逐渐增加的趋势,108杨和南杨则是呈现先减小后增加的趋势。相关性分析表明:木材密度与不同状态下干缩差异呈极显著负相关;木材基本密度除与弦向和体积气干干缩率不相关,与其他干缩指标均呈极显著正相关;不同干缩指标之间呈极显著正相关。     

杨树浸渍改性处理材尺寸稳定性研究

利用聚乙烯醇缩甲醛改性剂对杨树木材进行浸渍改性,对其改性材的尺寸稳定性进行研究。结果表明:改性材的径向、弦向和体积干缩率与素材相比均有不同程度的下降;从全干到吸水饱和状态的过程中,当改性剂达到一定浓度时,改性材的径向、体积湿胀率与素材相比有明显下降,弦向线湿胀率下降不明显。从气干到吸水饱和状态的过程中,改性材的径向、弦向湿胀率与素材相比均有不同程度的下降;改性材体积湿胀率随着改性剂浓度的上升而呈下降趋势,当改性剂浓度为30%时,改性材体积湿胀率为6.85%,与素材相比下降了5.54%。改性材吸水率随改性剂浓度的上升而下降,最低可达159%;改性材的抗干缩系数(ASE)随改性剂浓度上升而增加,最大可达47.8%。改性材的尺寸稳定性能要明显优于杨树素材。     

马尾松中龄施肥木材密度和干缩率的研究

选用广西马尾松龄施肥材料（连续观测13年），根据国际《木材物理力学试验方法》，研究了施肥对木材密度和干缩率的影响，结果表明：N、P、K三要素中，以N、P肥对木材密度和干缩率的影响较大。⑴总的来说P增加木材密度和干缩率，N肥降低木材密度木材干缩率。N、P肥降低木材差异干缩。施K肥对木材密度和干缩率的影响规律性不明显。⑵N、P、K施肥对木材密度和干缩率的影响及其变化程度，与肥种、施肥量、树干部位、木纹方向、气干或全干状态有关。施P肥木材密度具有增加的趋势，而且树干下部基本密度方差分析各处理间差异显著。N、K肥对木材密度的影响，规律性不明显。P肥使木材干缩率增加，P肥主要增加的是全干干缩率和径向气干干缩率，特别是树干下部径向气干干缩率各处理间差异显著。K肥对干缩率的影响规律性不明显，有待进一步研究。⑶为了保证木材质量，对于纤维用材林，主要施P肥；对于结构用材林，可施P肥，适当考虑N肥、K肥施用应慎重。     

黄毛青冈等四种硬木干燥特性的研究

对黄毛青冈、高山栲、滇石栎和栓皮栎等四种硬阔叶树材的构造、密度、全干缩率、弦、径向干缩变化、用百度法和气干等进行了观察和试验。结果表明四种木材导管内含有丰富或较多的侵填体,密度甚大,全干缩率大,弦、径向干缩比差异也大,水分传导性差,干燥速度缓慢,干燥时易发生表裂、内裂、翘弯和扭曲等现象,属难干材。通过试验,提出了克服干燥缺陷的一些措施,为制定四种木材干燥工艺提供了依据。     

长江滩地杨木密度和干缩性的研究

对安庆段长江滩地I-72杨的密度和干缩性进行了研究。结果表明:I-72杨的气干密度、全干密度和基本密度分别为0.454 g/cm3、0.415 g/cm3和0.364 g/cm3;I-72杨木材密度的径向变异为自髓心向外,最初递减,然后再向外层递增;轴向变异为沿树干向上逐渐增加;I-72杨的径向、弦向和体积全干缩率分别为3.917%、8.093%和12.138%,体积干缩系数为0.169,差异干缩为2.107;I-72杨5.3 m高度处的径向、弦向和体积全干缩率测量值均大于1.3 m高度处的测量值。     

火炬松短周期工业材不同高度上干缩性能的研究

对湖南同一立地指数（１８）下，５株１７．５年生的火炬松（ＰｉｎａｓｔａｅｄａＬ．）短周期工业材１．３，３．６，５．６，７．６，９．６ｍ５个高度的木材干缩系数、基本密度、生长轮宽度、晚材率和微纤丝角度，按生长轮取样，进行了测量和统计分析．结果表明，弦向、径向、体积干缩系数和干缩比，在树于５个高度之间的差异，均达到了显著水平；各高度干缩系数与生长轮的年龄（离髓心的距离）以及与上述各主要构造因子之间呈显著的线性相关，且相关度度随树干高度的增加而减弱．     

油松株内幼龄材与成熟材材性的比较研究

本文就中条山油松株内幼龄材与成熟材材性差异的比较研究,讨论对幼龄期划分的依据。根据木材解剖特征、物理力学性质的径向变异规律,确定其幼龄期为14年。随着树干高度的增加,油松木材幼龄期逐渐缩短、株内幼龄材范围及所占断面上的比例变小。株内幼龄材与成熟材材性差异显著。幼龄材管胞长度短、直径小,胞壁薄,微纤丝角度大,生长轮较宽,晚材率低,浸提物含量高,基本密度较大。幼龄材的力学强度远远小于成熟材。     

Effects of radial growth rate on selected indices for juvenile and mature wood of the Japanese larch

To examine the differences between juvenile and mature wood, 12 aged sample trees from two areas of Nagano Prefecture were harvested; and the radial development of tracheid length, the ring density, and the relation of the radial growth rate (observed by ring width) with some selected indices of ring structure were investigated. The results proved that the radial variation of tracheid length with ring number can be described by a logarithmic formula, and both plantations reached the demarcation of juvenile and mature wood at age 18. With the segmented regression method, we also analyzed radial variation of mean density and found that the demarcation of juvenile and mature wood was at age 15 for sample trees from Saku and at age 21 for those from Yabuhara. By using the results of estimates from juvenile and mature wood based on ring density, we found that high growth rates resulted when producing lower-density wood during the juvenile period, but these rates did not occur during the mature period. The basic reason for this phenomenon is the variation in patterns of earlywood and latewood in juvenile and mature wood, respectively. This result advised us that when managing plantations of Japanese larch it is necessary to take different measurements at different growth periods.     

红松幼龄材与成熟材力学性质的差异

本文研究了人工林和天然林红松幼龄材与成熟材力学性质的差异.结果显示,成熟材的所有力学性质均高于幼龄材.幼龄材与成熟材的抗弯弹性模量差异在人工林红松中达0.01水平显著,天然林红松也达到0.01水平显著;人工林红松抗弯强度和弦向横纹抗压强度差异达0.05水平显著.抗弯强度、顺纹抗压强度、横切面硬度和弦向横纹抗压强度4项指标的差异达0.05水平显著.     

Prediction of transverse shrinkages of young-growth Sitka spruce (Picea sitchensis) and western hemlock (Tsuga heterophylla) with ultrasonic measurements

Abstract

The objective of this study was to examine the potential of acoustic measurement as a rapid and nondestructive method to predict the dimensional stability of young-growth Sitka spruce and western hemlock. Ultrasonic velocity, peak energy, specific gravity, and radial and tangential shrinkages were measured on twenty-four 25-×102-×y 25-mm specimens obtained from a 58-year-old stand in Southeast Alaska. We found that specific gravity and peak energy of ultrasonic signals were not good predictors of transverse shrinkage, as indicated by poor correlations. Ultrasonic velocity, on the other hand, was found to be a significant predictor of transverse shrinkage and therefore has good potential to be used as a field method to evaluate dimensional stability. The single-parameter prediction model explained 86% of transverse shrinkages in western hemlock and 71% of transverse shrinkages in Sitka spruce. Further study is needed to test the capability and feasibility of using acoustic velocity to predict both longitudinal and transverse shrinkages of wood in standing trees.     

Performance of samama (Anthocephalus macrophyllus) LVL based on veneer thickness,juvenile proportion and lay-up

ABSTRACT

A study to determine the quality of laminated veneer lumber (LVL) from samama wood (Anthocephalus macrophyllus) was carried out. Samama is a fast-growing endemic wood in eastern Indonesia. Factorial of three factors in RAL design was used to investigate the influence of veneer thickness, juvenile proportion and veneer lay-up to the quality of the resulted samama LVL. The veneer thicknesses were 1.5 and 3.0?mm. Juvenile proportions were arranged in five levels, which were 100% of juvenile veneer, 100% of mature veneer and combination of both juvenile and mature with juvenile proportion of 14%, 43% and 71%. Two veneer lay-up used in this study were loose side met loose side and tight side met loose side. The result of the study showed various specific gravity of LVL by different proportions of juvenile. This factor also affected the other physical traits. Shear strength of the LVL was equal to the solid wood, yet MOE and MOR were affected by juvenile proportion and veneer lay-up. LVL developed from 100% of mature veneer exhibited the highest MOE and MOR, yet no significant difference was noted in MOE and MOR between LVL 100% of juvenile and other tested juvenile proportions.     

Differences in wood properties between juvenile wood and mature wood in 10 species grown in China

 This study examined the intrinsic differences in various wood properties between juvenile wood and mature wood in 10 major reforestation species in China. Comparisons between juvenile wood and mature wood were made in both plantation- and naturally-grown trees. Considerable differences in most wood properties were found both between plantation-grown juvenile wood and mature wood, and between naturally-grown juvenile wood and mature wood. This suggests that wood properties of plantation-grown trees, to a large extent, depends on their juvenile wood contents, and can thus be manipulated effectively through rotation age. In general, the longer the rotation age, the lower the juvenile wood content, and the stronger the mechanical properties of the plantation-grown woods. However, the differences between juvenile wood and mature wood vary with wood properties and species. In general, juvenile wood and mature wood have less difference in chemical composition than in anatomical and physico-mechanical properties. Compared to the softwoods studied, the hardwoods appear to have less difference between juvenile wood and mature wood. Received 25 June 1999     

Pilot Study to Examine Radial Variation in Annual Ring Width, Density and Shrinkage

The annual ring width, density and shrinkage variation from pith to bark in Chinese fir (Cunninghamia lanceolata) and Boka sugi (Cryptomeria japonicd) were studied and compared. The results show that the ring width decreased sharply from pith to bark for Chinese fir. However, the ring width variation pattern for Boka sugi followed a different way, i.e., the ring width decreased to the fifth ring, increased to the tenth ring, decreased again to the fifteenth, and then increased to the twentieth, where it became constant. The large variations of Boka sugi appeared to show the maintenance of fast growth for many years. The annual ring mean density of Chinese fir increased gradually from pith to bark. However, the density changes for Boka sugi indicated the opposite trend, i.e., the mean density decreased gradually from pith to bark. The former showed a pattern as the same as a pine and a larch, and the latter was often found in a cedar and a cypress. The longitudinal shrinkage in juvenile wood was much hig     

中国人工林展望:林木培育、木材质量及其合理利用(英文)

随着天然林保护工程的实施 ,我国木材资源结构正在进行由主要利用天然林木材到利用人工林木材的转变 .由于人工林木材所含幼龄材比例相当高 ,木材资源结构的变化反过来必将对我国的木材加工工业及林产品工业带来一系列影响 .该文综述了我国木材资源的现状 ,比较了人工林幼龄材与天然林成熟材的木材基本特性 ,探讨了人工林木材性质特征与营林培育的关系 ,阐述了木材质量与不同最终用途之间的关系 ,并对加强开展人工林木材性质的研究提出了几点建议     

大花序桉种源间木材物理性质变异研究

以广西东门林场18年生的11个大花序桉(Eucalyptus cloeziana)种源木材为研究对象,对它们的木材基本密度、弦向干缩率、径向干缩率等物理性质进行了测定分析,发现不同种源间、相同种源不同树干高度间所测定的物理性质指标均存在显著的差异。木材基本密度最大的种源是B85,然后依次是D47、B82,其值分别是0.7530、0.7386、0.7274 g/cm3;参试的11个种源中有8个种源的差异干缩都小于1.5,属于差异干缩小的类型;只有14425、12195和B55这3个种源的差异干缩超过1.5,但小于1.6,属于差异干缩中等类型;种源的树高、胸径生长性状与木材基本密度、差异干缩、体积全干缩率物理性状相关关系不密切,据此分别对树高、胸径等生长性状和木材基本密度、干缩率等木材物理性状进行独立选择可望获得较好的生长、物理性状改良效果。     

Determination of fiber length and juvenile and mature wood zones in Acer velutinum Boiss. trees grown in Iran

In our investigation we studied fiber lengths and the transition age from juvenile to mature wood in Acer velutinum Boiss. For this purpose, samples from three normal maple trees at a Noshahr site in northern Iran were selected. Disks were cut at breast height. Test samples were taken along a radial direction from the pith to the bark, accounting for every ring during a 48-year period. We used the Franklin method to distinguish between fibers of juvenile and mature wood. The results show that the fiber length increased along the radial direction from the pith to the bark. The transition age between juvenile and mature wood was determined at the 14th annual ring from the pith.