Clues to wood quality and production from analyzing ring width and density variabilities of fertilized Pinus taeda trees

Tree growth and wood density are influenced by forest management. Nevertheless, few studies have evaluated their variability responses to fertilizer treatments at inter-annual, inter-tree and stand-production levels. Therefore, the annual ring width (RW) and density (RD) of sixty 17-year-old-Pinus taeda trees fertilized with six doses of composted pulp-mill sludge (CPMS) were analyzed. Ten trees for each treatment were felled and from which wood discs were taken at different trunk heights. The annual RW and RD were provided by X-ray microdensitometry, synchronized and the trunk basic specific gravity (SG_B) and biomass calculated. The effects of CPMS treatments were explored using interaction of variables RW and RD with cambial age, diameter, trunk SG_B and biomass production. Trees treated with CPMS grow faster, increasing their biomass (up to 108%), presenting lower wood density values (significant up to the 6th year) and reaching the mature wood later than untreated trees. Furthermore, the potential use of RW and RD in allometric equations showed good accuracy to predict trunk SG_B and biomass. Altogether, our results indicated that ring width and density revealed the impacts of fertilization treatment on wood quality and production. Our study also provides useful information for forest managers on the fertilization monitoring process.

     

A high-throughput X-ray-based method for measurements of relative wood density from unprepared increment cores from Picea abies

We have described a high-throughput method for ring width and relative wood density analysis of unprepared increment cores based on conventional computer tomography scanners (CT scanners) used in health care. The method was developed for analysis of 5-mm increment cores collected in forest genetic and tree breeding trials. For these studies, the relative differences between individuals are more important than the exact value. The method is highly efficient in terms of quantitative data collection from large number of samples. There are, however, limitations in terms of resolution and accuracy on very small volumes of wood that must be considered when using the method to measure individual growth rings or increment cores thinner than 5 mm. However, in studies comprising large number of samples, the use of cost-efficient CT scanning on the major part of the material, combined with more laborious high-resolution scanning on sub-samples can be a good combination for efficient determination of radial variation in growth rate and wood density.     

Increasing the competitiveness of wood in material substitution: A method for assessing and prioritizing customer needs

To increase the competitiveness of wood as a building material requires knowledge of which customer needs require attention in terms of quality improvement and/or product development to best satisfy customers. Hence, information as to the impact on customer satisfaction of the fulfillment of different customer needs, as well as the performance of wood and substitutes in providing for these needs, is needed. This article suggests the use of customer satisfaction modeling (CSM) for assessing customer needs. The methodology is evaluated in the context of floorcovering. The results suggest that CSM is well suited for extracting the information necessary for prioritizing customer needs: importance/impact and performance data for attributes as well as for customer benefits. The study indicates the necessity of considering substitute materials not only for performance comparisons; substitutes may also reveal otherwise latent customer needs. Practical, functional, benefits exert the greatest impact on customer satisfaction for wooden flooring as well as its closest substitutes, laminate and carpet. Hygiene and a low cost over the life cycle are apparently the customer benefits that require attention from wooden flooring manufacturers, because importance is high and performance relatively low.     

Estimation of genetic data and breeding values of traits related to wax production in <Emphasis Type="Italic">Rhus succedanea</Emphasis> L. clones using the REML/BLUP method

Rhus succedanea L. is cultivated in Japan for the wax that can be extracted from its fruits. We determined genetic data for specific traits associated with wax production (fruit number per cluster, FN, fruit weight, FW, number of clusters per area, CN, and wax content, WC) in five traditional cultivars and 13 newer clones. Data were collected over 4 years and alternate bearing was observed: 2001 and 2003 were years with high yields; in 2002 and 2004 yields were poor. The restricted maximum likelihood method was used to calculate (co)variance components for analysis. Broad sense heritability was estimated and ranged from low (FN and CN) to high (FW and WC) for the traits examined. There were positive genetic correlations between FW and WC and negative ones between FN and FW throughout the 4 years. Genetic correlations between CN and the other traits were positive in good crop years and negative in bad crop years. For each assessed clone, the four traits in the 4 years were evaluated using best linear unbiased predictors (BLUP) of the clonal breeding values. The BLUP scores for both FW and WC exhibited positive correlations between pairs of years, whereas there were positive BLUP correlations for CN when the high yield and low yield years were examined separately. The traditional cultivars and the newer clones were also characterized. Some of the clones were better than the traditional cultivars with regard to wax yield and reliability of production. The trait characteristics and the future breeding are discussed.     

Performance of particleboard manufactured using air-injection press II: effects of board density and thickness on the performance of board manufactured from low-moisture particles

Particleboards of different densities (0.6, 0.7 and 0.8 g/cm³) and thicknesses (10 and 20 mm) were manufactured from low-moisture particles using an air-injection press. The effects of the air injection on preventing blowout of the boards of different densities and thicknesses were investigated by artificially creating blowout-prone conditions using metal frames. The effects of the air-injection pressure on the board performance were also investigated. 10-mm-thick boards of 0.8 g/cm³ pressed at 170 °C blew out when air was not injected, but were successfully manufactured by injecting air. 10-mm-thick boards at 150 °C showed constant internal bond (IB), regardless of density, but at 170 °C, IB was higher in boards of higher densities. This was likely due to accelerated hardening of the urea–formaldehyde resin at 170 than 150 °C. At both pressing temperatures, low air-injection pressure did not cause blowout and a reduction in board performance. Air injection also prevented the blowout of thick boards of 20 mm and enabled successful manufacture, showing its effectiveness. The IB of the 20-mm-thick board manufactured using the air-injection press exceeded that of 20-mm-thick board manufactured using an ordinary hot press.     

Development of an air-injection press for preventing blowout of particleboard V: effects of board density and thickness on property of board manufactured from high-moisture particles

Particleboards with thickness of 10 mm and densities of 0.6, 0.7 and 0.8 g/cm³ were manufactured from high-moisture particles using urea–formaldehyde resin and the effectiveness of air injection was examined. The temperature in the 0.6 and 0.7 g/cm³ boards was lower with air injection than without during the initial to middle stages of pressing, while the temperature in the 0.8 g/cm³ board remained lower with air injection than without throughout the entire pressing process. Air injection reduced the pressing time required to manufacture the 0.6 and 0.7 g/cm³ boards and also increased the internal bond strength of boards of all densities. In the 0.6 and 0.7 g/cm³ boards, air injection reduced the modulus of rupture (MOR), while in the 0.8 g/cm³ boards, the MOR was similar between those manufactured by injecting and not injecting air. Air injection was also found to be effective for boards of high densities. The effectiveness of the air injection on thick boards was investigated by manufacturing 20-mm-thick boards of 0.7 g/cm³. Without air injection, it was not possible to manufacture the 20-mm-thick boards, even by extended hot pressing, but air injection allowed the boards to be manufactured by pressing for 16 min. Air injection was also shown to be effective for manufacturing thick boards.     

Predicting individual breeding values and making forward selections from open-pollinated progeny test trials for seed orchard establishment of interior Lodgepole Pine (<Emphasis Type="Italic">Pinus contorta</Emphasis> ssp. <Emphasis Type="Italic">latifolia</Emphasis>) in British Columbia

Ten-year height data from three open-pollinated lodgepole pine progeny test trials were analysed in order to select individuals for seed orchard establishment in the low and high elevation seed-planning units (TOLO and TOHI) of the new Thompson Okanagan seed planning-zone in interior British Columbia, Canada. The total test population had about 35,000 individuals from 362 families of 9 provenances and was divided into two portions, each serving as the base population for its appropriate seed-planning unit. For each population, various genetic parameters were estimated and individual breeding values were predicted. Combined-site estimates of individual, family, and within-family heritability ranged from 0.23 to 0.38, 0.77 to 0.84, and 0.17 to 0.29, respectively. Estimated coefficients of type-b genetic correlation were greater than 0.81, indicating little G × E interaction in this region. Provenance effects were large. Larch Hills and Inonoaklin River were the two superior provenances with an expected gain of 13% and 10% in stem volume at rotation age of 60 years in TOLO. Individual breeding values was not uniformly distributed among provenances and the top 100 individuals originated from 20 families in TOLO and 32 families in TOHI. Co-ancestry among these individuals should not be a serious concern in seed orchard establishment as the predicted genetic loss due to excessive inbreeding is only 1.06% in TOLO and 0.6% in TOHI. The status numbers of the two prospective seed orchards are 32 and 44, respectively, and both are well above the required minimum of 10 in British Columbia. Using unrelated clones for seed orchard establishment may result in reduced optimum genetic gain and thus is not a favourable option.