Influence of fibre contents on mechanical and thermal properties of roselle fibre reinforced polyurethane composites

The aim of this paper is to study the effect of fibre content on mechanical and morphological properties and thermal stability of roselle fibres (RFs) reinforced polyurethane (TPU) composites. The RF/TPU composites were prepared at difference fibre contents; 10, 20, 30, 40 and 50 wt% by melt mixed mixer and hot press at 170 °C. Mechanical (tensile, flexural and impact strength) and Thermogravimetric analysis (TGA) properties of RF/TPU composites were measured according to ASTM standard. Obtained results indicated that effect of fibre contents display improved tensile and flexural and impact strength properties. RF/TPU composites show the best mechanical and thermal properties at 40 wt% roselle fibre content. Scanning electron microscopy (SEM) micrograph of fractured tensile sample of the roselle composite revealed good fibre/matrix bonding. TGA showed that RF/TPU with difference fibre contents had improved thermal stability.     

Characterization of light weight epoxy composites from short Sansevieria Cylindrica fibers

Sansevieria (genus) cylindrica (species) belongs to Agavaceae family plant fiber first time used as a reinforcing agent in the epoxy system. Fibre extracted from leaves, fairly lesser density, porosity, higher strength to weight ratio (hereafter called SCF) and these fibers were alkali-treated and yet impregnated on the epoxy system using wet hand lay up technique in order to compare with untreated fiber on performance. DMA, TGA, DSC, FTIR, SEM, degradation temperature, flexural and tensile tests were performed for untreated and alkali-treated epoxy composites using different SCF volumes viz. 1 vol.%, 5 vol.%, 7 vol.% and 9 vol.%. Alkali treated fibre were found to have higher initial and final degradation temperatures and flexural and tensile strength. The removal of the amorphous hemi-cellulose on alkali treatment was played an instrumental in improving properties. A 3 °C increase in glass transition temperature and decomposition temperature were recorded respectively and over all treated SCF composites reinforced on the epoxy were shown significant results than untreated. Storage modulus and tan ?? were observed well at 9 vol.% treated SCF while flexural and tensile were increased by 35 and 13 % for SCF treated composites respectively.     

Mechanical behavior of composites reinforced with fibers caroa

Composites were prepared with 13, 23 30 and 40 % fiber and evaluated the mechanical performance in tensile, flexural and impact. The mechanical properties of these composites were also evaluated function of time at 110 °C thermal exposure. Caroa fibers were characterized by techniques such as thermal gravimetric analysis (TGA), X-ray diffraction (XRD) and scanning electron microscopy (SEM). It was found that the best mechanical properties were achieved for composites containing 23 to 30 % fiber. The incorporation of 23 % fiber caroa increased both the modulus of elasticity in the tensile test as the flexural strength and impact, the composite with 30 % fiber caroa showed higher tensile strength. The results show that the tensile and flexural strength of the composite decreased with time of thermal exposure. The thermal aging at 110 °C caused a decrease in tensile properties of the composites.     

Effect of pineapple leaf fibre and kenaf fibre treatment on mechanical performance of phenolic hybrid composites

In this work, hybrid composites were fabricated by hand layup method to hybridize treated Pineapple leaf fibre (PALF) and kenaf fibre (KF) in order to achieve superior mechanical properties on untreated hybrid composites. Silane treated PALF/KF phenolic hybrid composites were prepared on various fibre fraction to investigate mechanical properties and compared with untreated PALF/KF phenolic hybrid composites. The effects of silane treatment on hybrid composites were investigated by fourier transform infrared spectroscopy (FTIR) and found very effective peaks. Effects of treated hybrid composites were morphologically investigated by using scanning electron microscopy images and analysed the tensile results. Treated PALF/KF phenolic hybrid composites enhanced the flexural strength, modulus, impact strength and energy absorption while tensile strength and modulus decreased. The overall performances of 70 % PALF 30 % Kenaf hybrid composites were improved after silane treatment. Silane treatment of fibres improved the mechanical performance of hybrid composites and it can be utilized to produce components for building structure, materials and automobile applications.     

Effects of plasticizer on the mechanical properties of kenaf/starch bio-composites

Research and development of biodegradable bio-composite can replacement the synthetic polymer materials, which is used for automobile interior materials, finishing materials of air conditioner and refrigerator. To develop both components as biodegradable bio-composite, this research used natural polymer starch as matrix and kenaf fiber as a filler. Various plasticizer(polyvinyl alcohol, polyethylene glycol, glycerol) were added and examined the mechanical properties of the kenaf/starch bio-composites according to these plasticizer. The kenaf bast which cultivated in Korea was retted with 2 % NaOH solution. The plasticizer weighting 10 % of that of matrix was added. kenaf/starch composites were molded with hot press for 30 minutes at 130 °C and 3,500 PSI molding condition. The mechanical properties such as tensile strength, elongation, and young modulus of the kenaf/starch composites were measured. Also, we measured the SEM cross-section images in order to investigate interfacial adhesion properties of fractured surfaces. The order of strength size of composites were G (12.42 MPa) > PVA (9.72 MPa) > PEG (4.73 MPa) samples respectively. The tensile strength of PEG sample is lower than the control sample (5.40 MPa).     

Effect of mercerization on mechanical, thermal and degradation characteristics of jute fabric-reinforced polypropylene composites

Jute fabric reinforced polypropylene composites were fabricated by compression molding technique. Fiber content in the composites was optimized at 45 % by weight of fiber by evaluating the mechanical parameters such as tensile strength, tensile modulus, bending strength, bending modulus. Surface treatment of jute fabrics was carried out by mercerizing jute fabrics with aqueous solutions of NaOH (5, 10 and 20 %) at different soaking times (30, 60 and 90 mins) and temperatures (0, 30 and 70 °C). The effect of mercerization on weight and dimension of jute fabrics was studied. Mechanical properties of mercerized jute-PP composites were measured and found highest at 20 % NaOH at 0 °C for 60 min soaking time. Thermal analytical data from thermogravimetric and differential thermal analysis showed that mercerized jute-PP composite achieved higher thermal stability compared to PP, jute fabrics and control composite. Degradation characteristics of the composites were studied in soil, water and simulated weathering conditions. Water uptake of the composites was also investigated.     

Mechanical and thermo-mechanical analysis based numerical simulation of granite powder filled polymer composites for wind turbine blade

In present article fabrication and characterization of unfilled and granite powder filled carbon epoxy composites are reported. Addition of carbon fiber shows positive effect on mechanical performance of the composites. However, incorporation of granite powder has negative hybridizing effect on the properties such as tensile strength, flexural strength and inter-laminar shear strength. The storage modulus evaluated at 30 °C is in close agreement with flexural modulus of composites. Further, successful attempt is made for numerical simulation of actual geometry of wind turbine blade. The results obtained from numerical analysis are comparable with experimental results.     

Green composites. I. physical properties of ramie fibers for environment-friendly green composites

The surface topography, tensile properties, and thermal properties of ramie fibers were investigated as reinforcement for fully biodegradable and environmental-friendly ‘green’ composites. SEM micrographs of a longitudinal and cross-sectional view of a single ramie fiber showed a fibrillar structure and rough surface with irregular cross-section, which is considered to provide good interfacial adhesion with polymer resin in composites. An average tensile strength, Young’s modulus, and fracture strain of ramie fibers were measured to be 627 MPa, 31.8 GPa, and 2.7 %, respectively. The specific tensile properties of the ramie fiber calculated per unit density were found to be comparable to those of E-glass fibers. Ramie fibers exhibited good thermal stability after aging up to 160°C with no decrease in tensile strength or Young’s modulus. However, at temperatures higher than 160°C the tensile strength decreased significantly and its fracture behavior was also affected. The moisture content of the ramie fiber was 9.9%. These properties make ramie fibers suitable as reinforcement for ‘green’ composites. Also, the green composites can be fabricated at temperatures up to 160°C without reducing the fiber properties.     

Flexural and impact properties of chemically treated sugar palm fiber reinforced high impact polystyrene composites

The effects of chemical treatment on the flexural and impact properties of sugar palm fiber reinforced high impact polystyrene (HIPS) composites were studied. Two types of concentration of alkali solution (4 % and 6 %) and also two types of percentage of compatibilizing agent (2 % and 3 %) have been used in this study. The alkaline treatment is carried out by immersing the fibers in 4 % and 6 % of alkali solution for 1 hour. A 40 wt. % of alkali treated sugar palm fiber (SPF) was blended with HIPS using Brabender machine at temperature of 165 °C. The second treatment was employed by compounding mixture of sugar palm fibers and HIPS with 2 and 3 % of compatibilizing agent using the same procedure. The composites plate with dimensions of 150×150×3 mm was produced by using the hot press machine. The flexural strength, flexural modulus and impact strength of composites were measured and the values were compared to the untreated composites. Improvement of the mechanical properties of the composites has been shown successfully. Alkali treatment using 6 % NaOH solution improve the flexural strength, flexural modulus and impact strength of the composites as amount 12 %, 19 % and 34 % respectively, whereas compatibilizing agent treatment only showed the improvement on the impact strength, i.e. 6 % and 16 % improvement for 2 % and 3 % MAH respectively.     

Flame retardancy,Thermal and mechanical properties of Kenaf fiber reinforced Unsaturated polyester/Phenolic composite

Unsaturated polyester (UP) resin has been blended with phenolic resin (PF) resole type at various ratios to obtain a homogeneous blend with improved flame resistance compared to its parent polymers. The polymer blend was reinforced with 20 wt% kenaf using hand lay out technique. Fourier transform infrared spectroscopy (FT-IR) was used to characterize changes in the chemical structure of the synthesized composites. The thermal properties of the composites were investigated using thermogravimetric analysis (TGA). The thermal stability of UP/PF kenaf composites co-varies with the PF content, as shown by the degradation temperature at 50 % weight loss. The char yield of the composites increases linearly with PF content as shown by the TGA results. The flammability properties of the composites were determined using the limiting oxygen index (LOI) and UL-94 fire tests. The LOI increased with the PF content while the composites exhibit improved flame retardancy as demonstrated by UL-94 test. The mechanical and morphological properties of the composites were determined by tensile test and scanning electron microscopy (SEM), respectively. The tensile strength and the Young’s modulus of the blend/composites slightly decreased with increasing PF content albeit higher than PF/kenaf fiber composites.     

Mechanical,thermal and interfacial properties of green composites from basalt and hybrid woven fabrics

Composites based on pure Basalt and Basalt/Jute fabrics were fabricated. The mechanical properties of the composites such as flexural modulus, tensile modulus and impact strength were measured depending upon weave, fiber contents and resin. Dynamic mechanical analysis of all composites were done. From the results it is found that pure basalt fiber combination maintains higher values in all mechanical tests. Thermo-gravimetric (TG/DTG) composites showed that thermal degradation temperatures of composites shifted to higher temperature regions compared to pure jute fabrics. Addition of basalt fiber improved the thermal stability of the composite considerably. Scanning electron microscopic images of tensile fractured composite samples illustrated that better fiber-matrix interfacial interaction occurred in hybrid composites. The thermal conductivity of composites are also investigated and thermal model is used to check their correlation.     

Hybrid effect in the mechanical properties of jute/rockwool hybrid fibres reinforced phenol formaldehyde composites

This research work was concerned with the evaluation of the effect of fibre content on the mechanical properties of composites. Composites were fabricated using jute/phenol formaldehyde (PF), rockwool/PF, and jute/rockwool hybrid PF with varying fibre loadings. Jute and rockwool fibre reinforced PF composites were fabricated with varying fibre loadings (16, 25, 34, 42, 50, and 60 vol.%). The jute/rockwool hybrid PF composites were manufactured at various ratios of jute/rockwool fibres such as 1:0, 0.92:0.08, 0.82:0.18, 0.70:0.30, 0.54:0.46, 0.28:0.72, and 0:1. Total fibre content of the hybrid composites was 42 vol.%. The results showed that tensile strength of the composite increased with increasing fibre content up to 42 vol.% over which it decreased for jute and rockwool fibre reinforced PF composites. Flexural strength of the composite was noted to peak at a fibre loading of 42 vol.% for jute/PF composites, and 34 vol.% for rockwool/PF composites. Impact strength of jute/PF composites increased with increasing fibre loading but that of rockwool/PF composites decreased at higher (>34 vol.%) fibre loadings. Tensile, flexural, and impact strengths of jute/PF composites were found to be higher than those of rockwool/PF composites. The maximum hardness values were obtained 42 vol.% for jute/PF composite, and 34 vol.% for rockwool/PF composite. Further increase in fibre loading adversely affected the hardness of both composites. For jute/rockwool hybrid PF composites, tensile and impact strengths decreased with increasing rockwool fibre loading. The maximum flexural strength of jute/rockwool hybrid PF composites was obtained at a 0.82:0.18 jute/rockwool fibre ratio while maximum hardness was observed at a 0.28:0.72 jute/rockwool fibre ratio. The fractured surfaces of the composites were analysed using scanning electron microscope in order to have an insight into the failure mechanism and fibre/matrix interface adhesion.     

Experimental studies on the physico-chemical properties of banana fibre from various varieties

Natural cellulosic fibres from various varieties of banana plants such as Red Banana, Nendran, Rasthaly, Morris and Poovan have been extracted manually and the physico-chemical properties of these fibres are investigated. The tensile strength of these fibres varies from 176 MPa to 525 MPa. The untreated fibres have more tensile strength than the treated one. The thermal properties of these fibres are studied by Differential Scanning Calorimetry (DSC). Two DSC thermal peaks, one is around 25°C to 180°C and the other is around 155°C to 240°C, are noticed. The tensile strengths have a direct correlation with the area of the lower thermal peak (enthalpy) and activation energy of the DSC, and also with the moisture absorption characteristics. The FTIR shows characteristic bands corresponds to cellulose. The reflections of the X-ray fibre diffraction pattern recorded for the banana fibre have been correlated with the mechanical strength.     

Completely biodegradable soyprotein-jute biocomposites developed using water without any chemicals as plasticizer

Soyprotein-jute fiber composites developed using water without any chemicals as the plasticizer show much better flexural and tensile properties than polypropylene-jute composites. Co-products of soybean processing such as soy oil, soyprotein concentrate and soy protein isolates are inexpensive, abundantly available and are renewable resources that have been extensively studied as potential matrix materials to develop biodegradable composites. However, previous attempts on developing soy-based composites have either chemically modified the co-products or used plasticizers such as glycerol. Chemical modifications make the composites expensive and less environmentally friendly and plasticizers decrease the properties of the composites. In this research, soyprotein composites reinforced with jute fibers have been developed using water without any chemicals as plasticizer. The effects of water on the thermal behavior of soyproteins and composite fabrication conditions on the flexural, tensile and acoustic properties of the composites have been studied. Soyprotein composites developed in this research have excellent flexural strength, tensile strength and tensile modulus, much higher than polypropylene (PP)-jute fiber composites. The soyprotein composites have better properties than the PP composites even at high relative humidity (90%).     

Preparation,properties and application of tamarind seed gum reinforced banana fibre composite materials

Technology has been developed to prepare a biodegradable and environmental friendly composite material from tamarind seed gum and banana fibre. Tamarind seed gum is prepared from the endosperm of roasted seeds of the tamarind tree. The different temperature condition maintained for roasting the seeds are 130, 160, and 180°C. Banana fibres are extracted from different varieties of banana trees, which are used for the preparation of composite material. The tensile strength of the composite material is measured and shows dependency on the variety of banana fibre used in the preparation and also the roasting temperature condition of the tamarind seed. Tamarind seed gum (the seed roasted at the temperature condition of 130°C) and Red banana fibre composite shows the highest tensile strength of 3.97 MPa and Poovan fibre composites shows the lowest tensile strength of 1.90 MPa. The composite material of other varieties shows tensile strength in between these two values. The percentage of moisture absorption of the composite material has a direct correlation to the tensile strength. In addition, investigation on fire retardant test of tamarind seed gum — banana fibre composite material revealed that untreated and varnish coated banana fibre composite material has good fire retardant characteristics. This is an important feature to promote the use of this composite material as a false roofing material instead of thermocole.     

Bio-composites: Development and mechanical characterization of banana/sisal fibre reinforced poly lactic acid (PLA) hybrid composites

The work focuses on the influencing effect of fiber surface treatment by BP towards mechanical properties of BSF reinforced PLA composites. BSF were treated by BP to improve the adhesion between fibres and matrix. BSF (30 wt %) reinforced PLA (70 wt %) hybrid composites were fabricated by means of twin screw extrusion followed by injection molding process. Tensile strength, flexural strength and modulus were tested by means of UTM. The morphological analysis of the untreated and treated BSF reinforced PLA composites in comparison with virgin PLA was carried out by SEM to examine the existence of interfacial adhesion between BSF and PLA. The resultant data reveals that treated BSF restricts the motion of the PLA matrix due to better wettability and bonding. Consequently, mechanical properties like tensile and flexural moduli of BSF reinforced PLA composites were enhanced in comparison to virgin PLA and untreated BSF reinforced PLA composites. The results are discussed in detail.     

Effect of γ (Gamma)-radiation on the physico-mechanical properties of grafted jute fabric reinforced polypropylene (PP) composites

The bleached jute fabric (BJF) reinforced polypropylene (PP) composites with various contents of acrylic acid (AA)-treated BJF and un-AA-treated BJF were fabricated by compression moulding method at 190 °C. The AA-grafted BJF reinforced PP composites were then irradiated by γ-ray at various doses. The mechanical properties of neat PP (N-P), ungrafted-BJF and PP composites (UG-BJFPC), AA-grafted-BJF and PP composites (AA-BJFPC) and γ-ray cum AA-grafted-BJF and PP composites (γAA-BJFPC) show maximum tensile strength (TS) of 30, 46, 47 and 51 MPa, maximum flexural strength (FS) of 34, 49, 50 and 54 MPa and maximum Young’s modulus (E) of 280, 428, 436, and 680 MPa, respectively. The increase of TS, FS and E from UG-BJFPC are 2 %, 2 %, and 2 % for AA-BJFPC and 11 %, 10 % and 59 % for γAA-BJFPC. The TS, FS and E are found to increase with radiation dose up to 500Krad and then decrease. The water absorption (WA) for UG-BJFPC, AA-BJFPC and γAA-BJFPC is respectively about 14, 10 and 9 %, indicating a gradual development of hydrophobic character of the composites first by AA-treatment and then by γ-ray-treatment. AA treatment on jute fabric and gamma irradiation on composite result in significant change of morphology of the jute fabric composites surface and better mechanical bonding between fabric and polymer matrix, as a result improved mechanical properties are found.     

Development of mathematical models and estimation for the mechanical properties of organic fiber reinforced polyester composites

Organic fiber from animal waste was used for the development of environmentally friendly animal fiber based polyester composites using cow hair. The cow hair fibers were cut into 10 mm lengths to produce the needed short fiber for random dispersion in the matrix. Before use, some of the fibers were treated with sodium hydroxide for fiber surface modification while some were left as untreated. Composites were developed using predetermined proportions of the fibers in an open mould production process. Samples were formed into tensile and flexural shape in their respective moulds and were stripped off the moulds after curing while further curing was ensured for 27 days before testing. Tensile and flexural properties of the cow hair fiber reinforced polyester composites were evaluated from which it was discovered that the untreated fiber reinforced composites possess better enhancement of mechanical properties compared to the treated fiber reinforced composites and the unreinforced polyester material. Mathematical models for the tensile and flexural properties were developed using statistical packages and estimation using developed software. The developed models revealed high degree of correlation between the experimental values and the predicted values. This denotes that the models can be used to predict the mechanical properties of cow hair reinforced polyester composites for various reinforcement contents.     

Green composites. II. Environment-friendly, biodegradable composites using ramie fibers and soy protein concentrate (SPC) resin

Fully biodegradable and environment-friendly green composite specimens were made using ramie fibers and soy protein concentrate (SPC) resin. SPC was used as continuous phase resin in green composites. The SPC resin was plasticized with glycerin. Precuring and curing processes for the resin were optimized to obtain required mechanical properties. Unidirectional green composites were prepared by combining 65 % (on weight basis) ramie fibers and SPC resin. The tensile strength and Young’s modulus of these composites were significantly higher compared to those of pure SPC resin. Tensile and flexural properties of the composite in the longitudinal direction were moderate and found to be significantly higher than those of three common wood varieties. In the transverse direction, however, their properties were comparable with those of wood specimens. Scanning electron microscope (SEM) micrographs of the tensile fracture surfaces of the green composite indicated good interfacial bonding between ramie fibers and SPC resin. Theoretical values for tensile strength and Young’s modulus, calculated using simple rule of mixture were higher than the experimentally obtained values. The main reasons for this discrepancy are loss of fiber alignment, voids and fiber compression due to resin shrinking during curing.     

Thermal Characterization of Alkali Treated Kenaf Fibers and Kenaf-Epoxy Composites

Chemical treatment of natural fibers is a well-defined means of mechanical property improvement in natural fiberreinforced composites. An understanding of mechanical and thermal properties in these media is essential for evaluating heat transfer, thermal degradation, and overall performance of these composites over their product lifetime. However, very little information is available illustrating the effect of such treatment on the thermal properties of kenaf composites. Also, no study to date has reported the thermal conductivity of individual kenaf fibers. This study reports the effects of fiber treatment (in 6 % NaOH) on thermal transport in unidirectionally oriented kenaf-epoxy composites and individual kenaf fibers. The effective thermal conductivities and thermal diffusivities of chemically treated fiber composites show a general increase over untreated fiber composites (0.210 to 0.232 W/m/K at 28 °C, 0.206 to 0.234 W/m/K at 200 °C). This improvement may be attributed to improved interfacial contact between the fibers and epoxy matrix shown in microstructural images after chemical treatment. The thermal conductivity of individual fibers was evaluated at room temperature using two techniques. Results from both techniques showed slight increases after chemical treatment (0.58±0.53 to 1.0±0.13 W/m/K and 1.2±0.54 to 1.6±0.28 W/m/K) but lacked statistical significance. Any improvement in surface crystallinity after chemical treatment does not appear to affect overall fiber thermal conductivity. A better understanding of thermal transport in kenaf fibers and composites enables better estimation of the performance of these composites in different applications. Moreover, the thermal conductivities of individual fibers are useful in understanding the fiber’s contribution to conduction in different fiber reinforcement configurations.