Evaluation of bamboo charcoal/stainless steel/TPU composite woven fabrics

Composite woven fabric satisfies what people require. Bamboo charcoal (BC) has been identified as a multifunctional material that has far-infrared ray, anions, deodorization and etc. BC fibers and yarns were made of bamboo charcoal powders and have further become a pervasive materials used in textile industry. In this study, cotton yarns, stainless steel/cotton (SS/C) complex yarn, bamboo charcoal/cotton (BC/C) complex yarns were woven into the plain, twill and Dobby composite woven fabrics. The warp yarn was composed of cotton yarns, and the weft yarn was made up of BC/C and SS/C complex yarns with a picking ratio of 1:1 and 3:1. Thermoplastic polyurethanes (TPU) film was then attached to the composite woven fabrics, forming the BC/SS/TPU composite woven fabrics. Tests of electromagnetic shielding effectiveness (EMSE), far-infrared emissivity, anions, water resistance, and water vapor permeability measured the single-layer, two-layer and four-layer composite woven fabrics, obtaining a far-infrared emissivity of 0.95 by 39.8 counts per minute, an anion count of 149 amount/cc, an EMSE of −11.87 dB under frequency of 900 MHz, a surface resistivity of 8×10⁻⁶ Ω/square, a water resistance of −8219 mmH₂O, and water vapor permeability of 989 g/m²·h and 319 g/m²·24 h in accordance with JIS L 1099 A1 and ASTM E96 BW.     

The Effects of Fabric and Conductive Wire Properties on Electromagnetic Shielding Effectiveness and Surface Resistivity of Interlock Knitted Fabrics

Our aim in this study was to investigate the effects of course density, yarn linear density and thickness and type of conductive wire on electromagnetic shielding effectiveness. Metal/cotton conductive composite yarns were produced by the core-spun technique on the ring spinning machine, involving stainless steel, copper and silver coated copper wires with 40 μm, 50 μm, 60 μm thicknesses and Ne10/1 and Ne20/1 count yarns. The interlock fabrics were knitted on a 7G flat knitting machine with the three different machine settings. The EMSE and the surface resistivity of knitted fabrics were measured by the co-axial transmission line method according to the ASTM-D4935-10 standard in the frequency range from 15 to 3000 MHz and by the ASTM D257-07 standard, respectively. It was observed that all fabrics shielded around 95 % of electromagnetic waves at low frequencies, 80 % at medium frequencies and 70 % at high frequencies. Increasing the course density and thickness of conductive wire in interlock knitted fabrics increased the EMSE correspondingly. The knitted fabrics that had been produced with high yarn count showed greater EMSE because there was less isolation. The effect of the metal wire type was highly significant between 15 and 600 MHz.     

Leveraging the Antibacterial Properties of Knitted Fabrics by Admixture of Polyester-Silver Nanocomposite Fibres

Leveraging the antibacterial properties of polyester-cotton knitted fabrics has been attempted in this research by admixture of small proportion of polyester-silver nanocomposite fibres. Polyester-cotton (50:50) yarns were spun by mixing 10, 20 and 30 % (wt.%) polyester-silver nanocomposite fibres with normal polyester fibres so that overall proportion of polyester fibre becomes 50 %. The proportion of cotton fibre was constant (50 %) in all the yarns. Three parameters, namely blend proportion (wt.%) of nanocomposite fibres, yarn count and knitting machine gauge were varied, each at three levels, for producing 27 knitted fabrics. Polyester-cotton knitted fabrics prepared from polyester-silver nanocomposite fibres showed equally good antibacterial activity (65-99 %) against both S. aureus and E. coli bacteria. Antibacterial properties were enhanced with the increase in the proportion of polyester-silver nanocomposite fibres, yarn coarseness and increased compactness of knitted fabrics. Yarn count and blend proportion of nanocomposite fibre were found to have very dominant influence in determining the antibacterial properties of knitted fabrics.     

Dimensional and physical properties of plain knitted fabrics made from 50/50 bamboo/cotton blended yarns

In this study, the dimensional and some physical properties of plain knitted fabrics made from 50/50 bamboo/cotton blended yarns are investigated. In order to see the differences and similarities, the results are then compared with those for similar fabrics knitted from 50/50 conventional viscose/cotton and 50/50 modal/cotton blended yarns. Each fabric type was produced with three different stitch lengths. After all fabrics were dyed under identical dyeing conditions, they were subjected to dry and full relaxation treatments. For dimensional properties of fabrics, course, wale and stitch densities were measured. Then, by calculating statistically best-fit lines passing both through the experimental points and the origin, dimensional constants i.e. k values were predicted in terms of the fiber types. The result show that each fabric type knitted from bamboo/cotton, viscose/cotton and modal/cotton blended yarns behaves in a similar manner. However, in both dry and fully relaxed states, the modal/cotton knitted fabrics tend to have slightly higher k values than the bamboo/cotton and viscose/cotton knitted fabrics. For physical properties, fabric weight per unit area, thickness, bursting strength, air permeability and pilling were evaluated. The results show that the weight, thickness and air permeability values are independent of the fiber type. Plain knitted fabrics from modal/cotton blended yarns have the highest bursting strength values. Plain knitted fabrics from bamboo/cotton blended yarns tend to pill less.     

Preparation and characterization of melt-spun PVC filament yarns

Polyvinyl chloride (PVC) fibers were melt-spun to prepare mono and multifilament yarns. To find optimum spinning and drawing conditions, various parameters such as spinning temperature, spinneret diameter, drawing temperature, and drawing ratio were examined. From the observation of the spinnability under various conditions, we found that the optimum conditions were as following: the extrusion temperature and die temperature were 175–180°C and 185–190°C, and the drawing temperature and drawing ratio were 85–95°C and 3.4, respectively. Under these conditions, the spinneret diameter could be reduced to the minimum value, 0.5 mm. Spun PVC filament yarns were subjected to the different yarn texturing process of stuffing box and pin false-twist method. The PVC yarn fabric was prepared by the knitting of textured yarns. Finally, the anion-emission and antibiotic properties of the knitted PVC fabrics were precisely evaluated.     

A comparative study on performance properties of yarns and knitted fabrics made of biodegradable and conventional fibers

Biodegradable products are parts of a natural cycle. The biopolymers and the fibers that can be produced from them are very attractive on the market because of the positive human perception. Therefore, PLA being a well known biodegradable fiber and some conventional fibers were selected for the current study to examine the differences between them and to emphasize the importance of biodegradability beside fabric performance. 14.8 tex (Ne 40/1) combed ring spun yarns produced from biodegradable fiber PLA, new generation regenerated fibers Modal and Tencel, synthetic and blends 50/ 50 % cotton/polyester and 50/50 % viscose/polyester, polyester were selected as yarn types and by using these yarns, six knitted fabrics were produced and some important yarn and fabric properties were compared. In this context, moisture and the tensile behavior of yarns and pilling, bursting strength, air permeability and moisture management properties of the test fabrics are discussed.     

Electromagnetic interference shielding effectiveness of SS/PET hybrid yarn incorporated woven fabrics

A detailed study of electromagnetic shielding effectiveness (EMSE) of woven fabrics made of polyester and stainless steel/polyester blended conductive yarn was presented in this research work. Fabrics with different structures were analyzed and their shielding behavior was reported under different frequencies. Shielding efficiency of fabric was analyzed by vector network analyzer in the frequency range of 300 kHz to 1.5 GHz using coaxial transmission line holder. The effects of different fabric parameters such as weft density, proportion of conductive weft yarn, proportion of stainless steel content, grid openness, weave pattern and number of fabric layers on EMSE of fabrics were studied. The EMSE of fabric was found to be increased with increase in proportion of conductive yarn in the weft way. With increase in overall stainless-steel content in the fabric, the EMSE of fabric was increased. As such weave is considered, it did not have significant effect on EMSE of fabrics. But fabric with lower openness and aperture ratio showed better conducting network, hence better shielding. With increase in number of layers of fabric and ply yarns, EMSE of fabric was increased.     

Assessment of color strength and color difference values of polyester fabrics containing continuous weft yarns after abrasion

This paper assesses the color difference and color strength values (K/S) obtained for eight disperse-dyed polyester fabric samples with different fabric construction parameters (weft yarn type, weft yarn count, weft density and fabric weave) after four sets of abrasion cycles. Warp yarn type and count, warp density, and warp yarn twist are the same for all fabrics. Fabric samples are dyed in a commercial red disperse dye (C.I. Disperse Red 74:1) and four different abrasion cycles (2500, 5000, 7500, 10000) are used. TheK/S values of the abraided fabrics and color difference values between the control fabric (dyed but not abraided) and abraded fabrics are calculated. The main differences in theK/S and color difference values are observed between 0–2500 abrasion cycles. The high tenacity of the polyester fibers and continuous polyester yarns causes some fuzz but no pilling formation on the fabric surface that lead to increasedK/S values and color differences. Fiber dullness, yarn thickness, yarn density and fabric weave are concluded to have different effects on the appearance after abrasion.     

Electromagnetic shielding characteristics of woven fabrics made of hybrid yarns containing metal wire

In this study, electromagnetic shielding characteristics of woven fabrics made of hybrid yarns are investigated. For this purpose, initially the hybrid yarns containing stainless steel wire are produced with hollow spindle covering technique, and then eight different fabric samples are produced using these hybrid yarns. Electromagnetic shielding values of fabric samples are determined by a test set up based on enclosure measurement technique. Measurements are made in the frequency range of 30 MHz-9.93 GHz. Test results show that woven fabric samples investigated in this study have 25–65 dB electromagnetic shielding effectiveness for incident frequency. It was also shown that the direction, density and settlement type of conductive hybrid yarn in fabric structure are important parameters affecting electromagnetic shielding characteristics of woven fabrics.     

Tear properties and meso-scale mechanism of multi-axial warp-knitted fabric from various architectures: Studied by photography

Tear properties tests of three kinds of multi-axial warp-knitted (MWK) fabric: triaxial fabrics (?45 °/90 °/+45 ° and ?45 °/0 °/+45 °) and biaxial fabric (?45 °/+45 °) were respectively implemented along the orientations of 0 °, 45 ° and 90 °. Load-displacement curves were well obtained. The high-speed camera was employed to observe the whole tear damage process and series of still images were picked up to analyze the meso-scale mechanism of the extension and displacement of tows on oriented layers. The results indicated the tear properties of MWK fabric are closely related to the orientations of the layers and the deformation mechanism of the layers. Stitching yarns incarnated significant effects in restricting the deformation procedures of tows.     

Investigation and modeling of air permeability of Cotton/Polyester blended double layer interlock knitted fabrics

The aim of this study was to analyze and model the effect of knitting parameters on the air permeability of Cotton/Polyester double layer interlock knitted fabrics. Fabric samples of areal densities ranging from 315–488 g/m² were knitted using yarns of three different cotton/polyester blends, each of two different linear densities by systematically varying knitting loop lengths for achieving different cover factors. It was found that by changing the polyester content in the inner and outer fabric layer from 52 to 65 % in the double layer knitted fabric did not have statistically significant effect on the fabric air permeability. Air permeability sharply increased with increase in knitting loop length owing to decrease in fabric areal density. Decrease in yarn linear density (tex) resulted in increase in air permeability due to decrease in areal density as well as the fabric thickness. It was concluded that response surface regression modeling could adequately model the effect of knitting parameters on the double layer knitted fabric air permeability. The model was validated by unseen data set and it was found that the actual and predicted values were in good agreement with each other with less than 10 % absolute error. Sensitivity analysis was also performed to find out the relative contribution of each input parameter on the air permeability of the double layer interlock knitted fabrics.     

Predicting properties of single jersey fabrics using regression and artificial neural network models

In our previous works, we had predicted cotton ring yarn properties from the fiber properties successfully by regression and ANN models. In this study both regression and artificial neural network has been applied for the prediction of the bursting strength and air permeability of single jersey knitted fabrics. Fiber properties measured by HVI instrument and yarn properties were selected as independent variables together with wales’ and courses’ number per square centimeter. Firstly conventional ring yarns were produced from six different types of cotton in four different yarn counts (Ne 20, Ne 25, Ne 30, and Ne 35) and three different twist multipliers (α _e 3.8, α _e 4.2, and α _e 4.6). All the yarns were knitted by laboratory circular knitting machine. Regression and ANN models were developed to predict the fabric properties. It was found that all models can be used to predict the single jersey fabric properties successfully. However, ANN models exhibit higher predictive power than the regression models.     

Compression properties of weft knitted fabrics consisting of shrinkable and non-shrinkable acrylic fibers

High-bulk worsted yarns with different shrinkable and non-shrinkable acrylic fibers blend ratios are produced and then single jersey weft knitted fabrics with three different structures and loop lengths are constructed. The physical properties of produced yarns and compression properties of produced fabrics at eight pressure values (50, 100, 200, 500, 1000, 1500 and 2000 g/cm²) were measured using a conventional fabric thickness tester. Then, weft-knitted fabric compression behavior was analyzed using a two parameters model. It is found that at 40% shrinkable fibre blending ratio the maximum yarn bulk, shrinkage, abrasion resistance and minimum yarn strength are obtained. It is also shown that high-bulk acrylic yarn has the highest elongation at 20% shrinkable fibre blend ratio. The statistical regression analysis revealed that the compression behavior of acrylic weft-knitted fabrics is highly closed to two parameter model proposed for woven fabrics. It is also shown that for weft-knitted structure, there is an incompressible layer (V′) which resists against high compression load. Acrylic weft-knitted fabrics with knit-tuck structure exhibit higher compression rigidity and lower softness than the plain and knitmiss structures. In addition, at 20% shrinkable fibre blend ratio, the high-bulk acrylic weft-knitted fabrics are highly compressible.     

Evaluation of the structural properties of plain fabrics woven from various fibers using Peirce’s model

Peirce’s fabric model has been widely used to predict the structural behavior of various plain woven fabrics. The structure of plain woven fabric can be defined in terms of the warp yarn number, weft yarn number, warp fabric density, weft fabric density, warp crimp, and weft crimp. The warp and weft yarn diameters are calculated from the warp and weft yarn numbers, and the effective coefficient of the yarn diameter is defined by using this model. We have investigated structural properties, such as the effective coefficient of the yarn diameter, yarn crimp, and fabric thickness for two different fabrics in which the constituent yarns are assumed to be either incompressible or compressible. This model is also applied to various plain fabrics woven from cotton, rayon, wool, linen, nylon, acetate, polyester, and silk yarns.     

Color and whiteness properties of fabrics knitted from different hybrid core-spun yarns containing metal wire

In this study, the color and whiteness properties of fabrics knitted from ring, siro and compact core-spun yarns containing metal wire were investigated. In general, an increase in the metal ratio of yarns causes a decrease in the whiteness and color strengths of fabrics. In our study, spinning method had no statistically significant effect on either the T _w or K/S values of fabrics while the effect of spinning method on the whiteness index of fabrics was briefly observed. Fabrics knitted from siro spun yarns showed higher whiteness properties than those of fabrics knitted from compact and ring spun yarns. This might be explained by the superior covering effectiveness of the siro spinning method on metal wire.     

Spinning performance and antibacterial activity of SeaCell® active/cotton blended rotor yarns

Microorganisms can lead to functional, hygienic and aesthetic (e.g. deterioration, staining) problems on textile products. Natural fibers especially cotton are more easily affected by microorganisms. Blending of cotton fibers with antimicrobial fibers can enhance the protective properties of products against microorganisms. Demand of antimicrobial performance from the products changes depending on the application area. Therefore determination of suitable antimicrobial fiber quantity for the desired application is important. In this study the spinning performance of SeaCell Active/cotton blended open end rotor yarns and antibacterial activities of fabrics produced by these blended yarns were investigated. Five different cotton/SeaCell Active blended slivers with SeaCell Active content from 3 % up to 53 % were prepared on drawframe machine and all slivers were spun into yarns on open end rotor spinning machine at a yarn count of 20 tex with α_Tt=3827 twist coefficient. The effects of rotor speed, opening roller speed, rotor, opening roller and navel type on the quality parameters of SeaCell Active/cotton blended yarns were investigated. Tensile properties, hairiness, unevenness and IPI values of the yarns were reported. All types of cotton/SeaCell Active blended yarns were knitted on a circular knitting machine. Antibacterial activity of the fabrics was analyzed quantitatively. Antibacterial tests showed that good antibacterial activity can be achieved after several washings even with 3 % of SeaCell Active fibers in fabrics.     

Analysis and off-axis tensile characterization of air-entangled textured polyester woven fabrics depending on unit cell interlacing frequency

The aim of this study is to analyze and determine the off-axis tensile properties of air-entangled textured polyester fabrics based on unit cell interlacing frequency. For this purpose, continuous filament polyester air-entangled textured yarn was used to produce plain, ribs and satin woven fabrics. The fabrics were cut from the warp direction (0°) to weft direction (90°) at every 15° increment, and tensile tests were applied to those of the off-axis samples. The strength and elongation results were introduced to the statistical model developed, and regression analyses were carried out. Hence, the effects of off-axis loading and interlacement on the directional tensile properties of the fabric were investigated. The regression model showed that off-axis loading influences fabric tensile strength. On the other hand, interlacement frequency is the most important factor for fabric tensile elongation. The results from the regression model were compared with the measured values. This study confirmed that the method used in this study as can be a viable and reliable tool. Future research will concentrate on multiaxially directional fabric and the probability that it will result in homogeneous in-plane fabric properties.     

Assessing the relationship among fabric constructional parameters, fractional reflectances and cover factors of polyester fabrics by experimental and mathematical methods

This paper focuses on the assessment of the relation among constructional properties, fractional reflectances and cover factors of fabrics woven from polyester yarns. A novel equation for the calculation of the relation between fractional reflectance and fabric cover factor was proposed and the usage of the equation was assessed by reflectance measurements. 48 polyester fabrics having different constructional parameters were used and the fabrics differed from each other by their cover factors. The warp yarn type and count, warp density and warp yarn twist were the same but weft yarn count, weft yarn fiber count and weft density were different for the fabrics in the experimental sub-groups. The reflectance measurements were conducted on the pretreated but undyed fabric samples as well as on the individual yarn systems of the same fabrics. Fabrics with the same cover factors exhibited different fractional reflectances. Reflectances were found to be dependent on the cover factor as well as on yarn fiber fineness, yarn count, yarn density and fabric weave. The changes in crimp of the yarns according to different construction parameters also governed the changes in fractional reflectances of fabric surfaces. The proposed equation was tested according to different fabric construction parameters and it was concluded that fiber fineness and weave pattern were among the most important parameters which govern the total light reflectances from the fabric surfaces, although they are not incorporated in the calculation of the fabric cover factors. The proposed equation was used to explain the effects of these components on the reflectance behavior of the fabric surfaces and on fabric cover.     

Mechanical anisotropy in unidirectional glass fabric reinforced oligomeric siloxane modified polyester composites

In this study, the effect of incorporation of oligomeric siloxane into unsaturated polyester on mechanical behavior of unidirectional glass fiber/polyester composites has been investigated by means of tensile, flexural and short beam shear tests. The amount of oligomeric siloxane added into unsaturated polyester was in the range 1?C3 % by weight of the glass fabrics. Mechanical tests were conducted at different angles (0 °, 45 °, and 90 °) with respect to fiber direction. The higher siloxane content exhibited a tendency to have greater tensile, flexural and interlaminar shear strength values in machine direction, bias direction and cross direction. From Scanning electron microscopy images, the presence of polyester particles on the unidirectional glass fiber surface confirmed better adhesion.