多点锚固体外无粘结CFRP预应力加固RC梁的抗弯性能

在梁侧或梁底用波形齿横向张拉CFRP片材并锚固的体外预应力加固混凝土结构技术,对3根完全相同的7 m跨T形截面梁进行加固：其中2根梁侧面加固;1根梁底部加固。试验表明：多点锚固体外无粘结CFRP预应力可以依据构件的弯矩来调整各段的加固量从而更有效的利用CFRP材料的高强性能;梁底与梁侧加固对提高构件的抗弯刚度差别不大;波形齿能彻底解决预应力CFRP片材的锚固问题。以该3根加固梁的试验结果为基础,提出了梁体极限状态下塑性绞区长度的体外无粘结预应力碳纤维加固受弯构件的抗弯承载力公式,以及考虑二次效应的有效惯性矩法的挠曲变形的计算公式,通过与试验值的对比分析可知,所提出的方法可供设计参考使用。     

A Study on the Test Method for Post-tensioned Prestressed Concrete Frame

A creative test method for post-tensioned prestressed frame is presented in this paper. In the test, the stationary supports at the column base are simulated and the forces at the column base can be tested while the two column bases are not connected with concrete beam. The prestressed secondary moment and the weight-produced moment are established by adjusting the support device at the column base. In this paper, the necessary conditions of the method and the basic process are recommended. It is proved theoretically that the prestressed concrete frame built by this method is equivalent to that used in practice.     

Suggestion for Moment Modulation of Prestressed Concrete Continuous Beams

Based on the information from China and overseas,a design suggestion for moment modulation of post-tensioned prestressed concrete continuous beams with bond has been put forth in this paper. The result calculated by the suggestion is consistent with the result of varying rigidity method.     

Discussion on the Secondary Moment of Prestressed Frame

The secondary moment of prestressed concrete frame is different from that of continuous beam. In this paper,the principle and calculation method of equivalent load secondary moment and axial secondary moment are discussed,and the infection of secondary moment in moment modulation is analyzed,together with the suggestions of moment modulation for prestressed concrete frame with adopting the total control. The suggestions would be able to distinguish the advantageous and disadvantageous effect of secondary moment. Some helpful advises for moment modulation design are given in this paper.     

A Study on the Test Method of Post-tensioned Prestressed Concrete Continuous Beam

A test method of post-tensioned prestressed concrete continuous beam is presented in this paper.In the test,the prestressed secondary moment is established by adjusting middle support height.The prestressed concrete continuous beam built by the method is equivalent to the beam in practice.     

Experimental Study on Moment Modulation of Prestressed Frames

Based on the experimental study of two prestressed frames in redistribution of Internal force, it can be concluded that the dominating influence factors on moment modulation are the relative height of equivalent compression zone, the secondary moment, the ratio of beam rigidity to column and development of cracks in the top of columns.The secondary moment is very important in modulation of frames. Especially, the secondary moment will governing the modulation when the relative height of equivalent compression zone is large enough.     

Experimental Study on a Prestressed Frame of Two Spans Under Unsymmetric Load

By the experimental study on a full-dimensioned prestressed frame of two spans, the relative factors are analyzed such as relative height of equivalent compression zone in critical section, secondary moment, ratio of beam rigidity to column and development of cracks in the top of columns etc., which influence the moment distribution of the post-tensioned prestressed concrete frame from the side of internal force redistribution. It is believed that that the factors of relative height of concrete equivalent compression zone and secondary moment influence the moment modulation in most degree, and ratio of column rigidity to beam also plays a part in the moment modulation to some extent. Second, the plastic joints of frame with excessive spans exit in the span which endure the whole load, at last the whole frame is destroyed because of the destruction of the loading frame, the influence to the non-loading span is little.     

Design and Test of an Exceedingly-long Prestressed Workshop Floor

Based on the project of a prestressed concrete beam-slab structure,this paper introduces the optimum design of a four-spanned exceedingly long prestressed floor. Different schemes,such as the scheme of the prestressed major beam,the scheme of the prestressed secondary beam with the same span and the scheme of the prestressed secondary beam with different spacing,are compared and analyzed in this paper.Meanwhile,various methods of the exceedingly treatment for long prestressed reinforcement are compared.Finally,based on two prestressed beams,the prestress loss,the prestressing value at the ends of the beam and the deflection in the midspan of the beam are detected during the tension and anchorage stage in order to verify the results of the theoretical analysis.     

体育馆大跨度预应力次梁楼盖竖向振动模态分析

以重庆市铜梁县新城核心区小学建设项目3^#楼（体育馆）工程为背景,对其大跨度预应力次梁楼盖竖向振动模态进行模拟分析,并与实测结果相比较,评价其控制竖向振动舒适度的效果。根据建模思路精确建立的该大跨楼盖有限元模型,其模态分析结果与模态实测结果接近,相对误差约为5%;模拟分析及工程实测结果表明,该大跨楼盖前三阶振型均以竖向振动为主,结构自振基频满足我国现行相关规范的要求,竖向振动舒适度符合标准;与无底板的大跨次梁楼盖相比,增加底板后,其增幅最小的一阶频率增长了19.9%,表明增加底板可有效地控制大跨度预应力次梁楼盖的竖向振动。     

Study on the Application of Large-span Prestressed Concrete Frame in Added Floor and Rebuilding

Around the reconstruction design of the Popular Science Image Building of the Southwest Hospital, the advantage of prestressed concrete frame used in the rebuilding was approved. At the same time, the problem in the prestressed frame design was pointed out. In the end, the method to decrease the moment in the column had been put forward.     

多点锚固预应力CFRP带加固T梁的有限元分析

采用非线性有限元分析程序ABAQUS对无粘结体外预应力CFRP片材加固简支钢筋混凝土T形梁后进行数值模拟,该模拟梁共4根分别为3根梁侧对称加固,1根为梁底加固均为四点波形齿锚固预应力CFRP带。对比结果显示,数据模拟与试验结果在构件屈服以前的承载力、变形以及极限承载力吻合程度较好,构件屈服以后的变形差别较大,因此,可在一定程度上有效替代试验分析方法。依据吻合程度最好的TL3参数设计了“两点锚固”和“四点锚固”的模型进行模拟分析。通过对锚固点数及加固量改变的对比分析可知,依据加固构件的弯矩改变各段加固量及布置锚固点数的方法既可以保证加固效果不降低,又可以节约CFRP材料。     

Comparative Study on Plastic Hinges of Prestressed Concrete Frames Under Vertical or Horizontal Loads

In With one-storey, two-span prestressed frames, a comparative study is done between under vertical and horizontal loads. The studies include the pattern of the plastic hinges occurring and, the demanded and available rotational capability of the hinges in critical sections. The relative height of compression zone and prestressed degree are considered. The result indicates that there is much difference in the pattern of the plastic hinge occurring when each plastic hinge has enough rotational capability. The beams can finish a full redistribution of internal force under vertical loads, but not under horizontal loads. Moreover, as increasing of the relative height of compression zone, a stronger rotational capability of hinges will be demanded to finish a full redistribution under vertical loads when a weaker rotational capacity will be needed under horizontal loads.     

Several Matters to be Noticed During the Moment Modulation Design of Prestressed Concrete Frame

The moment modulation of prestressed concrete frame has some differences compared with that of continuous beam.Based on the analysis of ratio of column linear rigidity to beam one,form of load,second moment and plastic hinge in column,this paper is intended to get some helpful advise for moment modulation design.     

Establishment of Pre-stress in Flat Beam of Tube-in-tube Structure

This paper introduces the analysis and test of prestressed flat beams in tube-in-tube concrete structures at different construction stages; moreover, the corresponding structural analysis models with FEA program are set up. Through the comparative analysis between the results of construction field test and that of calculation with FEA method, it proves the reliability of the primary design method; meanwhile, it also indicates that establishment of prestressing force and prestressed effects in similar structures is a complex procedure and should be noticed.     

Experimental Analysis on Bending Capacity of Unbonded Prestressed Concrete Beams with HRBF500 Steel Bars

The bending capacity tests on ten simple supported beams were conducted to investigate the damage characteristics, prestress increment, beading capacity and displacement ductility of unbounded prestressed concrete beams with HRBF500 steel bars. The results show that the HRBF500 steel bars has yielded before the limit state. The concrete in compression zone crushes upon the broken of the beams, which shows a sudden damage mode. The measured ultimate stress increments of unbounded tendons are in linear relationship with the comprehensive reinforcement ratio index, while the values of the ultimate stress increments are obviously higher than those values specified in the code GB50010-2010, and the average ratio of predicted values to testing values is about 0.35. The mid span deflection upon yielding of the beams is large, while the displacement ductility is bad and the average value of the displacement ductility ratio is 1.67. The displacement ductility ratio decreases with the increases of the comprehensive reinforcement ratio index. Based on the experimental results, the proposed calculation formula of ultimate stress increments of unbounded tendons was established, and it is in good agreement with the experimental results when the testing value is less than 450 MPa.     

Effect of Shear Lag on Structural Behaviours in Indeterminate Box Girders

A finite element method considering interaction betwee bending and shear lag deformation was proposed and the finite element formulations including the effect of shear lag was deduced. The effect of shear lag on structural behaviours in indeterminate box girders was studied in detail based on the proposed method. Firstly, the shear lag effects on deflection and the shear lag coefficients were analyzed for both determinate and indeterminate beams. The results obtained by using the proposed method were compared with those by using the analytical method. Finally, the effect of shear lag on redistribution of internal forces including shear force, bending moment, and additional bending moment due to shear lag in indeterminate box girder bridges was studied. It is found that the effects of shear lag on deflection and stresses at a cross section are obvious for both determinate and indeterminate beams, while the effect of shear lag on internal forces in indeterminate box girder bridges is small and may be neglected.     

Calculating the Support Reaction Increment''s Correlation Equation of R.C Continuous Beams

According to the hypothesis of plain section and the equation of moment versus curvature of R.C section, the elastic-plastic response of pressed continuous beams is analyzed with CDC-method. The correlation equation of support reaction increment and displacement increment is induced through the relation of moment increment and curvature increment,and the adjustment value of support reaction increment of continuous beams is determined by solution of linear equation systems,which provides a rule the support reaction to follow. It can roundly and quantificationally display the moment redistribution behavior of continuous beams. A case of 4 spans continuous beam shows a high calculation rate and precision of this method.     

Test & Analysis of Moment-Torque Distribution Between Spandrel Beams And Beams of Floor System With P.C. Long-span Beams

The test of four large scale specimens of floor system with P.C. long-span beams is introduced.The restraining torsional moment of spandrel beams caused by P.C. beams with or without slab is focused on,along with change of the load-torque relationship affected by the beams' bending rigidity and the spandrel beams' torsional rigidity under different load level. The result presents important reference to the revision of national design standard and structural design.     

Fire Resistance Analysis of High Strength Q460 Steel Beams-Part I：Theoretical Analysis

In order to investigate the fire resistance of high strength steel beams made from Q460, the method to compute temperature distribution of high strength Q460 steel beams was derived and the temperature distribution was calculated by using finite difference method. The modified equations of temperature for components of steel beam were proposed. According to critical moment at room temperature and mechanical properties of high strength Q460 steel at elevated temperature, the critical moment and stability checking coefficient were obtained by analysis. The load bearing capacity and critical temperature as well as stability factor were studied by using equivalent stiffness method through considering the effect of temperature gradient on stiffness.     

Measurement and Analysis of Prestressed Concrete Flat Beam- Waffle Slab System During Prestressing

During the pre - stressing of the unbonded prestressed concrete wide flat beam - waffle slab system, the displacements and strains of slab and the prestressed concrete beams were site - measured and the results were analyzed. The prestressing construction was simulated by finite element program. The prestressing efficiency of the unbonded prestressed concrete wide flat beam - waffle slab system was discussed. It indicates that the prestressing efficiency was affected by the in -plane stiffness of slab.