Evaluation of DRAINMOD for predicting water table heights in irrigated fields at the Jordan Valley

A detailed field experiment was carried out in the Jordan Valley, south of Lake Kinneret, Israel for evaluation of the water management model DRAINMOD. This field was chosen to represent the local agro-climate conditions of that zone. Banana crop was grown and was irrigated daily with about 3200 mm/year and 0.5 leaching fraction. Subsurface drainage system with 2.5 m drain depth and 160 m drain spacing existed in the field. The water table depth was measured with about 100 piezometers, in which most of them were observed weekly, and four were continuosly recording piezometers. Five identical drainage plots were selected, out of 10 existing, as replicates for the evaluation of DRAINMOD. Deviations in a range of 0.3–1.7 m between observed water table depth and that simulated by DRAINMOD were found in four out of the five replicates. A reasonable agreement was found only in one drainage plot out of the five tested. These findings contradict the world wide convention that DRAINMOD simulation is in a good agreement with observed field data. An additional study was therefore conducted to explore the reasons for these large deviations. Three reasons were suggested: (i) a strong side effect by the Jordan River, which flows some 350 m west to the test field; a very steep 4.6% gradient was found toward the Jordan River; (ii) presence of sandy permeable layers below the depth of the drains which magnifies the boundary condition effect of the Jordan River; (iii) a very significant component of deep and lateral seepage (more than 50% of the yearly irrigation plus rainfall). A combination of these three reasons was suggested as an explanation to the apparent large disagreement. It was therefore recommended not to use DRAINMOD or similar vertical flow models for simulation of water table depths in irrigated fields with subsurface drain pipe systems in the Jordan Valley.     

Nitrogen loss through subsurface drainage effluent in coastal rice field from India

Experiments were conducted to estimate nitrogen loss through drainage effluent in subsurface drained farmers’ field at a coastal site near Machilipatnam, Andhra Pradesh, India. The concentration of three forms of nitrogen, namely, NH₄–N, NO₂–N and NO₃–N in the subsurface drainage effluent from 15, 35 and 55 m drain spacing areas were measured in 1999 and 2000. The area with 15 m spacing was already reclaimed during 1986–1998 by the subsurface drainage system. The soil salinity of the root zone was brought down from an initial high of 35 to 4 dS m⁻¹. The subsurface drainage system with 35 and 55 m drain spacing was laid in the adjoining area and commissioned in 1998. Earlier raising of any crop in the area with 35 and 55 m spacings was not possible due to very high salinity, sodicity and poor drainage conditions. The nitrate-nitrogen loss dominated in reclaimed land with 15 m spacing whereas ammonium-nitrogen loss dominated in the land that was highly saline and in the initial stage of reclamation by the subsurface drainage technology with 35 and 55 m drain spacing. The total nitrogen loss of 3.75 kg per ha per year in 15 m drain spacing area was minimum and 23.53 kg per ha per year in 35 m drain spacing area was maximum. The nitrate-nitrogen loss contributed the maximum of 82% and ammonium- and nitrite-nitrogen contributed 11 and 7%, respectively, in 15 m drain spacing area whereas the ammonium losses contributed 93 and 82% in 35 and 55 m drain spacing areas, respectively. The losses in the form of nitrite and nitrate remained negligible in 35 m drain spacing area, but the losses to the tune of 8 and 15% in the form of nitrite and nitrate, respectively, occurred in 55 m drain spacing area.     

Controlled drainage — effects on drain outflow and water quality

A field experimental project was set up in southern Sweden to assess the effects of controlled drainage on hydrology and environment. Controlled drainage makes it possible to vary the drainage intensity with the variation in drainage requirement during season by controlling the height of a riser in the drain outlet and thus to a certain degree control the amount of outflow of solutes via the drainage system. During periods with low drainage demand, the riser in the drain outlet can be raised and the groundwater level in field will rise up to the level of the riser before the discharge takes place. Three plots, each with an area of 0.2 ha (40 m×50 m) were installed on a loamy sand. One plot was drained by conventional subsurface drainage (CD) and two plots were drained by controlled drainage (CWT). The plots contained four lateral drain tubes, at 10 m spacing and placed at 1 m depth. Each plot was isolated by a double layer of plastic sheeting placed in the back-filled trenches to a depth of 1.6 m to prevent lateral leakage and subsurface interactions. Measurements of precipitation, drain outflow and soil and air temperatures were carried out hourly. Groundwater levels were measured and samples of drain outflow were collected twice a month for nitrogen and phosphorous analyses. Mineral nitrogen contents in soil were measured three times a year.Controlled drainage had a significant hydrological and environmental effect during the 2 years of measurement (1996–1998). Compared with CD, the total drain outflow from CWT was 79% less in Year 1 and 94% in Year 2. The total reduction in nitrate losses with CWT corresponded to the reduced outflow rates. Compared with CD, the total amounts of nitrate in drain outflow were 78% less in Year 1 and 94% in Year 2. The highest concentrations of nitrate were measured at the time of the largest outflow rates. The phosphorous losses were 58% less for CWT as compared to the CD values in Year 1 and 85% less in Year 2. The reduction in nitrogen content in the soil profile during the winter season was 60–70% less in CWT than in CD.     

Evapotranspiration of flood-irrigated pecans

Pecan orchards require more irrigation water to maximize yield than any other crop grown in the Southwest US. This paper reports daily evapotranspiration (Et) measurements for 2001 and 2002 in a 5.1 ha, mature pecan orchard on the Rio Grande floodplain, 7 km south of Las Cruces, NM, USA. The 21-year-old stand had an average tree height of 12.8 m, diameter at breast height of 30 cm, and tree spacing of 9.7 m × 9.7 m. Additional pecan orchards surrounded the study orchard. When the tensiometer reached a suction of 65 kPa at the 45 cm depth, the orchard was flood-irrigated. Sparling meters were installed on the pumps and read before and after each irrigation. The total irrigation amount was 1940 mm in 2001 and 1870 mm in 2002. A walk-up tower was placed in the orchard’s center to support flux sensors at 16 m height. The instrument package included a net radiation (Rn), discs for soil heat flux (G), and two sets of one-propeller eddy covariance (OPEC) sensors. OPEC systems measure sensible heat flux (H) with a sensitive, vertically oriented propeller anemometer and a fine-wire thermocouple. Latent heat flux (LE) was obtained as a residual in the surface energy balance LE = Rn − G − H. The maximum daily evapotranspiration was 8 mm/day, and the yearly cumulative evapotranspiration averaged for 2 years was 1420 mm, resulting in a yearly average irrigation application efficiency of 79%. The crop coefficient (daily measured Et/reference Penman Et) ranged from 0.2 to 1.1. Increased evaporation due to irrigation was detected only for the April 9 irrigation in 2001. The seasonal water use was 4% lower in 2001 and 12% lower in 2002 than previously reported values.     

Effects of irrigation method on chile pepper yield and Phytophthora root rot incidence

A field experiment was conducted in 1995 and 1996 to examine the effects of different irrigation methods on yields and Phytophthora root rot disease of chile plants (Capsicum annum New Mexico `6–4'). Three irrigation methods, daily drip, 3-day drip, and alternate row furrow irrigation, were applied to plots infested with P. capsici and uninfested plots. For both years, the drip irrigation (either daily or 3-day) created higher marketable green chile yields than the alternate row furrow irrigation (p < 0.05), and the yields between the daily and 3-day drip irrigation were statistically similar. The effect of irrigation on marketable combined yields was similar to that on green chile yields. In 1995, root rot disease incidence in the infested plots was significantly higher under alternate row furrow irrigation than for daily and 3-day drip irrigation. There was no disease development in the uninfested plots regardless of the irrigation method. The disease decreased green chile yield by 55% (p < 0.1), and combined yield (green + red chile) by 36% (p < 0.1) in 1995 compared to that in uninfested plots in alternate row furrow irrigation. In 1996, however, no disease occurred in any treatment. The results suggested that drip irrigation increases chile yield through providing either favorable soil moisture conditions or unfavorable conditions for Phytophthora propagation.     

Analysis of several discharge rate–spacing–duration combinations in drip irrigation system

In order to study the use of water irrigation in a rational way, several combinations of discharge rate, irrigation duration and inter-emitter distances were tested. For instance, three dripper spacings of 30, 50 and 70 cm which delivered water volumes of 4, 8 and 16 l per dripper, respectively, and three discharge rates of 2, 4 and 8 l/h for each spacing, were applied.An overlapping of the wetted bulbs was observed at the end of the different irrigation experiments. The inter-dripper root-zone had an average water content of 45% and a coefficient of uniformity of 90%.The discharge rate of 2 l/h applied to a 70 cm dripper spacing was characterised by water losses of 15% due to the significant irrigation duration (8 h).From this study, we reach the following conclusions, specific to the soil type and practical culture.

• 1.The maximum irrigation duration does not exceed 4 h.
• 2.Two hours durations can be used for the different spacings, each of which was characterised by its own discharge rate.

     

Evaluation of drainage and tillage effect on watertable depth and maize yield in wet inland valleys in southwestern Nigeria

A study was conducted in three wet inland valley bottoms, namely, high (MHW), medium (MMW) and low (MLW) watertable sites to evaluate the effect of drained (D) and control (Do), and mound-tillage (MT), ridge-tillage (RT) and no-tillage (NT) treatments on watertable depth and yield of maize in 1990 wet and 1990/1991 dry season in southwestern Nigeria. The watertable depth averaged 30.0 cm in the drained plot and <15.0 cm in the control plot in 1990. The watertable tended toward its lowest depth averaging 44.8 cm in the drained and 26.2 cm in the control plot in 1990/1991. Soil moisture content was lower (P<0.01) and air-filled porosity greater (P<0.01) in the mound-tilled compared with the ridge tilled and no-till soils in both drained and control plots in 1990 and 1990/1991. Equally, green maize yield from the mound-tillage and ditch drainage system was greater (P<0.01) than the ridge-tillage and no-tillage systems in both seasons. Maize may be grown successfully with a ditch drainage and mound-tillage system in the wet soils in inland valley bottoms regardless of their watertable regimes in southwestern Nigeria.     

Managing subsurface drip irrigation in the presence of shallow ground water

A 3-year project compared the operation of a subsurface drip irrigation (SDI) and a furrow irrigation system in the presence of shallow saline ground water. We evaluated five types of drip irrigation tubing installed at a depth of 0.4 m with lateral spacings of 1.6 and 2 m on 2.4 ha plots of both cotton and tomato. Approximately 40% of the cotton water requirement and 10% of the tomato water requirement were obtained from shallow (<2 m) saline (5 dS/m) ground water. Yields of the drip-irrigated cotton improved during the 3-year study, while that of the furrow-irrigated cotton remained constant. Tomato yields were greater under drip than under furrow in both the years in which tomatoes were grown. Salt accumulation in the soil profile was managed through rainfall and pre-plant irrigation. Both drip tape and hard hose drip tubing are suitable for use in our subsurface drip system. Maximum shallow ground water use for cotton was obtained when the crop was irrigated only after a leaf water potential (LWP) of −1.4 MPa was reached. Drip irrigation was controlled automatically with a maximum application frequency of twice daily. Furrow irrigation was controlled by the calendar.     

Forage production of cool season pasture grasses as related to irrigation

A significant portion of the irrigated acreage in the intermountain western U.S. is comprised of cool season grass pastures. Droughts, coupled with increasing demands for limited water supplies in the region, have decreased the water volumes available for irrigating these pastures and other crops. Consequently, relationship between crop yield and irrigation (water production functions) should be defined for various species and cultivars to help growers and water managers make appropriate selections based on water availability.During a 3-year study on the Colorado Plateau, a line-source irrigation system was used to evaluate the relationship between applied water and dry forage production of orchardgrass (Dactylis glomerata L.), tall fescue (Festuca arundinacea Schreb.), meadow brome (Bromus riparius Rehmann), smooth brome (Bromus inermis Leyss.), two cultivars of intermediate wheatgrass (Elytrigia intermedium [Host] Nevski), crested wheatgrass (Agropyron cristatum L. Gaertn. X desertorum [Fisch. ex Link] J.A. Schultes) and perennial ryegrass (Lolium perenne L.). Irrigation treatments, including precipitation, ranged from 457 to 970 mm in 1996, 427 to 754 mm in 1997 and 490 to 998 mm in 1998. There was a positive linear relationship between yield and irrigation for all cultivars when averaged over all years but the relationships varied between cultivars and years. Orchardgrass, meadow brome and tall fescue produced more dry forage than the other grasses at the highest irrigation levels in all years. These grasses also produced the greatest rates of yield increase per unit of irrigation (average of 0.0129 Mg ha⁻¹ mm⁻¹) and exhibited greater yield stability from year to year than the other grasses at irrigation levels above 700 mm. The intermediate wheatgrasses produced more forage than the other grasses under limited irrigation (less than 600 mm) but the average production rate with irrigation (0.0066 Mg ha⁻¹ mm⁻¹) was only about half that of the aforementioned grasses. The average rate of forage produced per mm of irrigation was intermediate in the smooth brome (0.0096 Mg ha⁻¹) and lowest in the crested wheatgrass and perennial ryegrass (0.0048 and 0.0034 Mg ha⁻¹, respectively). These results suggest that orchardgrass and meadow brome be included in irrigated pastures receiving more than 700 mm of water annually while the intermediate wheatgrasses be selected for pastures receiving an annual water application of less than 700 mm.     

Trickle and sprinkler irrigation of potato (Solanum tuberosum L.) in the Middle Anatolian Region in Turkey

The potato (Solanum tuberosum L.) is widely planted in the Middle Anatolian Region, especially in the Nigde-Nevsehir district where 25% of the total potato growing area is located and produces 44% of the total yield. In recent years, the farmers in the Nigde-Nevsehir district have been applying high amounts of nitrogen (N) fertilizers (sometimes more than 900 kg N ha⁻¹) and frequent irrigation at high rates in order to get a much higher yield. This situation results in increased irrigation and fertilization costs as well as polluted ground water resources and soil. Thus, it is critical to know the water and nitrogen requirements of the crop, as well as how to improve irrigation efficiency. Field experiments were conducted in the Nigde-Nevsehir (arid) region on a Fluvents (Entisols) soil to determine water and nitrogen requirements of potato crops under sprinkler and trickle irrigation methods. Irrigation treatments were based on Class A pan evaporation and nitrogen levels were formed with different nitrogen concentrations.The highest yield, averaging 47,505 kg ha⁻¹, was measured in sprinkler-irrigated plots at the 60 g m⁻³ nitrogen concentration level in the irrigation treatment with limited irrigation (480 mm). Statistically higher tuber yields were obtained at the 45 and 60 g m⁻³ nitrogen concentration levels in irrigation treatments with full and limited irrigation. Maximum yields were obtained with about 17% less water in the sprinkler method as compared to the trickle method (not statistically significant). On the loam and sandy loam soils, tuber yields were reduced by deficit irrigation corresponding to 70% and 74% of evapotranspiration in sprinkler and trickle irrigations, respectively. Water use of the potato crop ranged from 490 to 760 mm for sprinkler-irrigated plots and 565–830 mm for trickle-irrigated treatments. The highest water use efficiency (WUE) levels of 7.37 and 4.79 kg m⁻³ were obtained in sprinkle and trickle irrigated plots, respectively. There were inverse effects of irrigation and nitrogen levels on the WUE of the potato crops. Significant linear relationships were found between tuber yield and water use for both irrigation methods. Yield response factors were calculated at 1.05 for sprinkler methods and 0.68 for trickle methods. There were statistically significant linear and polynomial relationships between tuber yield and nitrogen amounts used in trickle and sprinkler-irrigated treatments, respectively. In sprinkler-irrigated treatments, the maximum tuber yield was obtained with 199 kg N ha⁻¹. The tuber cumulative nitrogen use efficiency (NUE_cu) and incremental nitrogen use efficiency (NUE_in) were affected quite differently by water, nitrogen levels and years. NUE_cu varied from 16 to 472 g kg⁻¹ and NUE_in varied from 75 to 1035 g kg⁻¹ depending on the irrigation method. In both years, the NH₄-N concentrations were lower than NO₃-N, and thus the removed nitrogen and nitrogen losses were found to be 19–87 kg ha⁻¹ for sprinkler methods and 25–89 kg ha⁻¹ for trickle methods. Nitrogen losses in sprinkler methods reached 76%, which were higher than losses in trickle methods.     

Assessment of the effect of tie-ridging on smallholder maize yields in Malawi

Tie-ridging is being promoted in Malawi as an on-field rainwater harvesting technique to ensure a maize (Zea mais L.) crop during a dry or drought year. Resource-poor smallholder farmers are likely to take up tie-ridging if it increases and not decreases maize yield in most years. A numerical study was conducted to calculate the expected maize yield gain due to tie-ridging taking into account the probability of occurrence of drought, dry, normal and wet years (climatic uncertainty). Mean yields due to tie-ridging in drought, dry, normal and wet years at different N levels were derived from observed smallholder maize yield data using a linear nitrogen response model and field-observed retained rainwater amounts in tie-ridged fields. Simulation results indicate that tie-ridging will result in hybrid maize yield gain in a drought year (1050 kg ha⁻¹) and dry year (560 kg ha⁻¹). There will be a hybrid maize yield loss in a normal year (350 kg ha⁻¹) and wet year (700 kg ha⁻¹). For local maize, there will be a yield gain in a drought year (500 kg ha⁻¹), dry year (220 kg ha⁻¹) and normal year (120 kg ha⁻¹). There will be a slight yield loss in a wet year (60 kg ha⁻¹). Considering observed probability of the occurrence of drought, dry, normal and wet years in Malawi, the study reveals that there will be no hybrid maize yield gain in any coming year with tie-ridging. For local maize, the expected yield gain in any coming year was positive (133.3 kg ha⁻¹) but this gain is less than the minimum gain required considering the opportunity cost of labour (142.5 kg ha⁻¹). Thus under the smallholder conditions and climate of Malawi, the expected yield gain in any coming year due to tie-ridging is likely to be minimal and uneconomic.     

Development and evaluation of integrated water and nitrogen model for maize

Maize (Zea mays L.) is an important food crop for irrigated regions in the world. Its growth and production may be estimated by different crop models in which various relationships between growth and environmental parameters are used. For simulation of maize growth and grain yield, a simulation model was developed (Maize Simulation Model, MSM). Dynamic flow of water, nitrogen (N) movement, and heat flow through the soil were simulated in unsteady state conditions by numerical analysis in soil depth of 0–1.8 m. Hourly potential evapotranspiration [ET_p(t)] for maize field was estimated directly by Penman–Monteith method. Hourly potential evaporation [E_p(t)] was estimated based on ET_p(t) and canopy shadow projection. Actual evaporation of soil surface was estimated based on its potential value, relative humidity of air, water pressure head and temperature at soil surface layer. Actual transpiration (T_a(t)) was estimated based on soil water content and root distribution at each soil layer. Hourly N uptake by plant was simulated by N mass flow and diffusion processes. Hourly top dry matter production (HDMA^j + 1, where j is number of hours after planting) was estimated by hourly corrected intercepted radiation (RSLT^j + 1) by plant leaves [determined from leaf area index (LAI^j + 1)] with air temperature, the maximum and minimum plant top N concentration and the amounts of nitrogen uptake. The value of LAI^j + 1 at each hour was estimated by the accumulated top dry matter production at previous hour using an empirical equation. Maize grain yield was estimated by a relationship between harvest index and seasonal plant top dry matter production. The model was calibrated using data obtained under field conditions by a line source sprinkler irrigation. When the values of water and nitrogen application were optimum, grain yield (moisture content of 15.5%) was 16.2 Mg ha⁻¹. Model was validated using two independent experimental data obtained from other experiments in the Badjgah (Fars province). The experimental results validated the proposed simulation model fairly well.     

Water–yield relations and optimal irrigation scheduling of wheat in the Mediterranean region

Crop yield is primarily water-limited in areas of West Asia and North Africa with a Mediterranean climate. Ten years of supplemental irrigation (SI) experiments in northern Syria were conducted to evaluate water–yield relations for bread wheat (Triticum aestivum L.) and durum wheat (Triticum turgidum L.), and optimal irrigation scheduling was proposed for various rainfall conditions. The sensitive growth stages of wheat to water stress were from stem elongation to booting, followed by anthesis, and grain-filling. Water stress to which crop subjected depends on rainfall and its distribution during the growing season; the stress started from early March (stem-elongation stage) or even in seedling stage in a dry year, and from mid-April (anthesis) in an average or wet year. Crop yield linearly increased with increase in evapotranspiration (ET), with an increase of 160 kg for bread wheat and of 116 kg for durum wheat per 10 mm increase of ET above the threshold of 200 mm. Water-use efficiency (WUE) with a yield ≥3 t ha⁻¹ was ca. 60% higher than that with yield <3 t ha⁻¹; this emphasises the importance of that to achieve effective use of water, optimal water supply and relatively high yields need to be ensured. Quadratic crop production functions with the total applied water were developed and used to estimate the levels of irrigation water for maximizing yield, net profit and levels to which the crops could be under-irrigated without reducing income below that which would be earned for full SI under limited water resources. The analysis suggested that irrigation scenarios for maximizing crop yield and/or the net profit under limited land resource conditions should not be recommended. The SI scenarios for maximizing the profit under limited water resource conditions or for a targeted yield of 4–5 t ha⁻¹ were recommended for sustainable utilization of water resources and higher WUE. The time of irrigation was also suggested on the basis of crop sensitivity index to water stress taking rainfall probability and available soil water into account.     

Opening floodgates in coastal floodplain drains: effects on tidal forcing and lateral transport of solutes in adjacent groundwater

The effects of opening tidal barriers (floodgates) upon water table levels and lateral transport of solutes adjacent drains was investigated at two sites on a coastal floodplain. The sites had contrasting geomorphology, soil texture and sediment hydraulic properties. The site with lower hydraulic conductivity (0.3–0.9 m day⁻¹) soils (Romiaka) also had a higher elevation and hydraulic gradients towards the drain. While floodgate opening at Romiaka enhanced the amplitude of pre-existing tidal interaction with adjacent shallow groundwater, altered hydraulic gradients and caused some salt seepage, lateral solute movement from the drain was highly attenuated (<10 m). The site with very high hydraulic conductivity soils (Shark Creek; >125 m day⁻¹) had a lower elevation and seasonally fluctuating hydraulic gradients. The introduction of a tidal pressure signal into the drain by opening the floodgate at Shark Creek caused tidal forcing of groundwater over 300 m from the drain. Floodgate opening at this site also caused changes in groundwater hydraulic gradients, leading to incursion of saline drain water into shallow groundwater over 80 m from the drain. Lateral movement of solutes was relatively rapid, due to macropore flow in oxidised acid sulfate soil horizons, and caused substantial changes to shallow groundwater chemical composition. Conversely, when groundwater hydraulic gradients were towards the drain at this site there was substantial lateral outflow of acid groundwater into drains. This study highlights the importance of assessing the hydraulic properties of soils next to drains on coastal floodplains prior to opening floodgates, particularly in acid sulfate soil backswamps, in order to prevent unintended saline intrusion into shallow groundwater.     

Cotton yield and applied water relationships under drip irrigation

Different irrigation scheduling methods and amounts of water ranging from deficit to excessive amounts were used in cotton (Gossypium hirsutum L.) irrigation studies from 1988 to 1999, at Lubbock, TX. Irrigation scheduling treatments based on canopy temperature (T_c) were emphasized in each year. Surface drip irrigation and recommended production practices for the area were used. The objective was to use the 12-year database to estimate the effect of irrigation and growing season temperature on cotton yield. Yields in the irrigation studies were then compared with those for the northwest Texas production region. An irrigation input of 58 cm or total water application of 74 cm was estimated to produce maximum lint yield. Sources of the total water supply for the maximum yielding treatments for each year averaged 74% from irrigation and 26% from rain. Lint yield response to irrigation up to the point of maximum yield was approximated as 11.4 kg ha⁻¹ cm⁻¹ of irrigation between the limits of 5 and 54 cm with lint yields ranging from 855 to 1630 kg ha⁻¹. The intra-year maximum lint yield treatments were not limited by water input, and their inter-year range of 300 kg ha⁻¹ was not correlated with the quantity of irrigation. The maximum lint yields were linearly related to monthly and seasonal heat units (HU) with significant regressions for July (P=0.15), August (P=0.07), and from May to September (P=0.01). The fluctuation of maximum yearly lint yields and the response to HU in the irrigation studies were similar to the average yields in the surrounding production region. The rate of lint yield increase with HU was slightly higher in the irrigation studies than in the surrounding production area and was attributed to minimal water stress. Managing irrigation based on real-time measurements of T_c produced maximum cotton yields without applying excessive irrigation.     

Water conservation practices for a river valley irrigated with groundwater

Water conservation strategies for center pivot and furrow irrigation in the Central Platte Valley of Nebraska were evaluated using computer simulation. Irrigation requirements, grain yield, return flow and net depletion (gross irrigation minus return flow) of groundwater were simulated for a period of 29 years for Hord and Wood River silt loam soils. Grain yields were simulated for a typical corn variety for non-limiting water supplies (maximum attainable yield), for two levels of deficit irrigation (irrigation limited to certain growing periods), and for dryland conditions. Additional simulations were performed for a short-season corn, grain sorghum, and soybeans. The impacts of tillage practices on water conservation were also investigated.Center pivot irrigation on the Hord silt loam required 75–125 mm/year less water application than furrow irrigation. For the Wood River silt loam, water applications were the same for both irrigation systems. Applied water depths were reduced by an additional 75–125 mm using deficit irrigation with only a small reduction in yield. Return flow to the groundwater was small for well-managed pivots but high for some furrow irrigation systems based on the assumption that all deep percolation returns to the aquifer in the Central Platte Valley. Net depletion (gross irrigation minus return flow) of the groundwater for a center pivot with LEPA was 50 mm (17%) less than a center pivot with impact sprinklers. Ridge till had a net depletion 50 mm (25%) less than conventional tillage (double disk, plant) for furrow systems.     

Latent heat flux over a furrow-irrigated tomato crop using Penman–Monteith equation with a variable surface canopy resistance

The Penman–Monteith (P–M) model with a variable surface canopy resistance (r_c) was evaluated to estimate latent heat flux (LE) or crop evapotranspiration (ET) over a furrow-irrigated tomato crop under different soil water status and atmospheric conditions. The hourly values of r_c were computed as a function of environmental variables (air temperature, vapor pressure deficit, net radiation, and soil heat flux) and a normalized soil water factor (F), which varies between 0 (wilting point, θ_WP) and 1 (field capacity, θ_FC). The Food and Agricultural Organization (FAO-56) method was also evaluated to calculate daily ET based on the reference evapotranspiration, crop coefficient and water stress coefficient. The performance of the P–M model and FAO-56 method were evaluated using LE values obtained from the Bowen ratio system. On a 20 min time interval, the P–M model estimated daytime variation of LE with a standard error of the estimate (SEE) of 46 Wm⁻² and an absolute relative error (ARE) of 3.6%. Thus, daily performance of the P–M model was good under soil water content ranging from 118 to 83 mm (θ_FC and θ_WP being 125 and 69 mm, respectively) and LAI ranging from 1.3 to 3.0. For this validation period, the calculated values of r_c and F ranged between 20 and 114 s m⁻¹ and between 0.87 and 0.25, respectively. In this case, the P–M model was able to predict daily ET with a SEE of 0.44 mm h⁻¹ (1.1 MJ m⁻² d⁻¹) and an ARE of 3.9%. Furthermore, the FAO-PM model computed daily ET with SEE and ARE values of 1.1 mm h⁻¹ (2.8 MJ m⁻² d⁻¹) and 5.2%, respectively.     

Yield and fibre quality of cotton cultivars as affected by the build-up of sodium in the soils with sustained sodic irrigations under semi-arid conditions

Cotton is commonly grown in many arid and semi-arid regions of the world having sodic ground waters. A field plot study was, therefore, conducted for 2 years to study the effect of sustained sodic irrigation on yield and fibre quality of two hirustum cotton cultivars (F-505 and F-846) and one arborium cultivar (LD-327). The exchangeable sodium percentage (ESP) of 0–30 cm soil under sustained canal water (CW) irrigation treatment was 3.5 whereas long-term irrigations (for more than 10 years) with sodic waters having residual sodium carbonate (RSC) of 5, 10 and 15 me l⁻¹ resulted in ESP bulid-up of 16.4, 39.6 and 56.2, respectively. These sodic waters were used for irrigation in the respective plots, for both years of the study. High ESP of the soil decreased the growth (in terms of plant height) and yield of all the three cotton cultivars. The rate of decline in plant height at 50, 80 and 140 days of sowing (DAS) was maximum in F-505 and minimum in F-846. Compared with CW treatment, relative seed-cotton yield under 16.4, 39.6 and 56.2 ESP levels obtained with respective sodic water treatments for 2 years were 99, 70 and 69%, respectively in F-846, 101, 46 and 29%, respectively in F-505 and 98, 67 and 49%, respectively in LD-327. Similar trends were observed in case of boll number per square metre and boll weight. The cultivar F-846 produced heavier bolls than the other two cultivars under ESP levels of 56.2 obtained under RSC₁₅ treatment which helped this cultivar to perform relatively better. The harmful effect of sodic waters on fibre quality (2.5% span length, micronaire value and bundle strength) were also not observed in the case of F-846. A slight deterioration in fibre quality was, however, observed in cultivars F-505 and LD-327 at an ESP of 56.2 in the soil.     

Grain yield and water use in a long-term fertilization trial in Northwest China

The wheat- (Triticum aestivum L.) and corn- (Zea mays L.) rotation system is important for food security in Northwest China. Grain yield and water-use efficiency [WUE: grain yield/estimated evapotranspiration (ET)] were recorded during a 24-year fertilization trial in Pingliang (Gansu, China). Mean yields of wheat for the 16 years, starting in 1981, ranged from 1.29 Mg ha⁻¹ for unfertilized plots (CK) to 4.71 Mg ha⁻¹ for plots that received manure (M) annually with nitrogen (N) and phosphorus (P) fertilizers (MNP). Corn yields for the 6 years, starting in 1979, averaged 2.29 and 5.61 Mg ha⁻¹ for the same respective treatments. Whether the years were dry, normal or wet, average grain yields and WUEs for both crops were consistently highest in the MNP and lowest in the CK treatment, and were always lower in the N than in the M treatment and in all others treatments that received N along with P fertilizers. More importantly, WUEs for MNP and for straw along with N annually and P every second year (SNP) were always higher than the other fertilized treatments in dry years. Compared to yield data, coefficients of variance (CV) for WUEs were consistently low for all treatments, suggesting that WUEs were relatively stable from year to year. Yields and WUEs declined over time, except in the CK and MNP treatments for wheat. Declined yields of wheat for the N and M treatments were comparable, and the decline for the NP treatment was similar to that for the SNP treatment. Likewise, corn yields and WUEs declined for all treatments. Grain yields were significantly correlated with ET, with slopes ranging from 0.5 to 1.27 kg m⁻³ for wheat and from 1.15 to 2.03 kg m⁻³ for corn. Balanced fertilization and long-term addition of organic material to soil should be encouraged in this region to maximize the use of stored soil water, arrest grain yields decline, and ensure sustainable productivity using this intensive cereal cropping system.     

Water use and lint yield response of drip irrigated cotton to the length of irrigation season

A 2-year experiment was conducted at Tal Amara Research Station in the Bekaa Valley of Lebanon to determine water use and lint yield response to the length of irrigation season of drip irrigated cotton (Gossypium hirsutum L.). Crop evapotranspiration (ET_crop) and reference evapotranspiration (ET_rye-grass) were directly measured at weekly basis during the 2001 growing period using crop and rye-grass drainage lysimeters. Crop coefficients (K_c) in the different growth stages were calculated as ET_crop/ET_rye-grass. Then, the calculated K_c values were used in the 2002 growing period to estimate evapotranspiration of cotton using the FAO method by multiplying the calculated K_c values by ET_rye-grass measured in 2002. The length of irrigation season was determined by terminating irrigation permanently at first open boll (S1), at early boll loading (S2), and at mid boll loading (S3). The three treatments were compared to a well-watered control (C) throughout the growing period. Lint yield was defined as a function of components including plant height at harvest, number of bolls per plant, and percentage of opened bolls per plant.Lysimeter-measured crop evapotranspiration (ET_crop) totaled 642 mm in 2001 for a total growing period of 134 days, while when estimated with the FAO method in 2002 it averaged 669 mm for a total growing period of 141 days from sowing to mature bolls. Average K_c values varied from 0.58 at initial growth stages (sowing to squaring), to 1.10 at mid growth stages (first bloom to first open boll), and 0.83 at late growth stages (early boll loading to mature bolls).Results showed that cotton lint yields were reduced as irrigation amounts increased. Average across years, the S1 treatment produced the highest yield of 639 kg ha⁻¹ from total irrigations of 549 mm, compared to the S2 and S3 treatments, which yielded 577 and 547 kg ha⁻¹ from total irrigations of 633 and 692 mm, respectively, while the control resulted in 457 kg ha⁻¹ of lint yield from 738 mm of irrigation water. Water use efficiency (WUE) was found to be higher in S1 treatment and averaged 1.3 kg ha⁻¹ mm⁻¹, followed by S2 (1.1 kg ha⁻¹ mm⁻¹), and S3 (1.0 kg ha⁻¹ mm⁻¹), while in the control WUE was 0.80 kg ha⁻¹ mm⁻¹. Lint yield was negatively correlated with plant height and the number of bolls per plant and positively correlated with the percentage of opened bolls. This study suggests that terminating irrigation at first open boll stage has been found to provide the highest cotton yield with maximum WUE under the semi-arid conditions of the Bekaa Valley of Lebanon.