Development and characterization of bamboo gauze fabric coated with polymer and drug for wound healing

The bamboo yarn of Ne 40^s was used for the preparation of the Gauze fabric. The physical properties such as areal density and stiffness of fabrics were measured. The fabric was then scoured and bleached as per the standard procedure using distilled water. Chitosan-sodium alginate, Calcium-sodium alginate polymer and their mixture were coated separately on the gauze structure to improve the antibacterial and wound healing property of the bandage. Scanning electron microscope (SEM) analysis was carried out to observe the uniform distribution of polymers in the samples. The antibiotic drugs were selected based on the antibiotic sensitivity test. The drugs such as Tetracycline hydrochloride (250 mg), Chloramphenicol (250 mg) and Rifampicin (250 mg) were immobilized on the polymer coated fabrics to increase the rate of wound healing and antibacterial activity. The drug loaded samples were subjected to drug release study for about four days in a static condition. The results show that good amount of drug was released during all the four days. Further, the antibacterial activity of the drug loaded and polymer coated samples were evaluated against S. aureus and Proteus bacteria. The results show excellent antibacterial activity.     

Transport properties of layered fabric systems based on electrospun nanofibers

Layered fabric systems with electrospun polyurethane fiber web layered on spunbonded nonwoven were developed to examine the feasibility of developing protective textile materials as barriers to liquid penetration using electrospinning. Barrier performance was evaluated for layered fabric systems, using pesticide mixtures that represent a range of surface tension and viscosity. Air permeability and water vapor transmission were assessed as indications of thermal comfort performance. Protection performance and air/moisture vapor transport properties were compared for layered fabric systems and existing materials for personal protective equipment (PPE). Layered fabric systems with electrospun nanofiber web showed barrier performance in the range between microporous materials and nonwovens used for protective clothing. Layered fabric structures with the web area density of 1.0 and 2.0 g/m² exhibited air permeability higher than most PPE materials currently in use; moisture vapor transport was in a range comparable to nonwovens and typical woven work clothing fabrics. Comparisons of layered fabric systems and currently available PPE materials indicate that barrier/transport properties that may not be attainable with existing PPE materials could be achieved from layered fabric systems with electrospun nanofibrous web.     

Characteristics of double-layer coated fabrics with and without phase change materials and nano-particles

Stability in a low temperature environment is needed for a textile to be used as winter wear. This research was presented the characteristics of fabrics by double-thin-layered coating with and without phase change materials (PCM) and several nano-sized inorganic particles (N-particles). Silica, Ag, Zr, and carbon types of N-particles were used for investigating the N-particles effect. For the experimental method, the PCM and N-particles were coated consecutively in the wet and dry coating process, respectively. The N-particles on the surface of the coated fabrics were confirmed by energy dispersive spectroscopy (EDS), and after double-layer composite coating, the adhesion durability, water vapor permeability, water penetration resistance, DSC, thermographic photography, far infrared (FIR) emission effect, and the thermal insulation of the coated fabrics were tested for investigating the performances. Their compatibility and adhesion were superior when the add-on of N-particles was 10 %. From the DSC reproducibility results, we verified that the N-particles coated fabric preserved its thermal stability by absorbing latent heat. On the other hand, the FIR emission rate and energy of the Ag N-particle based sample were not better than the control sample.     

Facile fabrication of PVAc-g-PVDF coating on surface modified cotton fabric for applications in oil/water separation and heavy metal ions removal

Selective separation is an effective method for the removal of heavy metal ions and waste oil from wastewater. Polyvinylidene fluoride (PVDF) was functionalized with polyvinyl acetate (PVAc) by in-situ polymerization, and novel PVAc-g-PVDF coating on surface modified cotton fabric were prepared. The contact angle (CA), pure water flux (PWF) and self-cleaning ability of coated cotton fabric were investigated in detail. In addition, the separation performance of coated cotton fabric was reflected by the removal of heavy metal ions in simulated wastewater. The results revealed that the PVAc-g-PVDF-coated cotton fabric was free of waste oil adhesion and was self-cleaning from waste oil in aqueous environment. Meanwhile, this coated cotton fabric can effectively separate oil/water mixtures with a high flux and high oil rejection, and was easily recycled for long-term use. More importantly, the heavy metal ions rejection ratio and adsorption capacity of cotton fabric were also improved with the addition of PVAc-g-PVDF coating. PVAc-g-PVDF-coated cotton fabric exhibited excellent rejection stability and reuse performances after several times fouling and washing tests. It can be expected that the present work will provide insight into a scaled-up fabrication process of PVAc-g-PVDF coating for purifying wastewater.     

Evaluation of bamboo charcoal/stainless steel/TPU composite woven fabrics

Composite woven fabric satisfies what people require. Bamboo charcoal (BC) has been identified as a multifunctional material that has far-infrared ray, anions, deodorization and etc. BC fibers and yarns were made of bamboo charcoal powders and have further become a pervasive materials used in textile industry. In this study, cotton yarns, stainless steel/cotton (SS/C) complex yarn, bamboo charcoal/cotton (BC/C) complex yarns were woven into the plain, twill and Dobby composite woven fabrics. The warp yarn was composed of cotton yarns, and the weft yarn was made up of BC/C and SS/C complex yarns with a picking ratio of 1:1 and 3:1. Thermoplastic polyurethanes (TPU) film was then attached to the composite woven fabrics, forming the BC/SS/TPU composite woven fabrics. Tests of electromagnetic shielding effectiveness (EMSE), far-infrared emissivity, anions, water resistance, and water vapor permeability measured the single-layer, two-layer and four-layer composite woven fabrics, obtaining a far-infrared emissivity of 0.95 by 39.8 counts per minute, an anion count of 149 amount/cc, an EMSE of −11.87 dB under frequency of 900 MHz, a surface resistivity of 8×10⁻⁶ Ω/square, a water resistance of −8219 mmH₂O, and water vapor permeability of 989 g/m²·h and 319 g/m²·24 h in accordance with JIS L 1099 A1 and ASTM E96 BW.     

Modification of cotton fabric by mussel-inspired for oil/water separation

An oil/water separation cotton fabric with high separation efficiency has been successfully developed by combining mussel-inspired one-step copolymerization approach and Michael addition reaction. The cotton fabric was first coated with the adhesive polydopamine (PDA) film by simple immersion in an aqueous solution of dopamine at pH of 8.5. Then n-dodecyl mercaptan (NDM) was conjugated with PDA film through Michael addition reaction at ambient temperature. The chemical structure, surface topography, and surface wettability of the fabric were characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy, and contact angle experiments, respectively. The results showed that as-prepared cotton fabric had highly hydrophobicity with the water contact angle of 145° and superoleophilicity with the oil contact angle of 0°. It exhibited desirable property of oil/water separation, and it had excellent potential to be used in practical applications and has created a new field for oil/water separation.     

Manufacturing and analyses of wet-laid nonwoven consisting of carboxymethyl cellulose fibers

Carboxymethyl cellulose (CMC) is a cellulose derivative having water-soluble property, biodegradability, and biocompatibility. It has been used in various medical applications as forms of gel, film, membrane, or powder. In this study, composite CMC nonwovens were produced, by a wet-laid nonwoven process, to improve the wet strength of carboxymethyl cellulose nonwovens. Followed by preparing the CMC fibers from cotton fiber, the composite CMC nonwovens composed of CMC fibers and PE/PP bicomponent fibers were manufactured by using 85/15 % v/v of ethanol/water solution as a dispersion medium. Structural analyses of CMC fibers, such as XRD, TGA, FT-IR, and degree of substitution indicated that CMC fibers were successfully produced. The wet strength of CMC nonwoven was dramatically increased by blending with the PE/PP fibers without sacrificing the key properties for wound dressing materials such as liquid absorption, gel blocking and liquid retention. It is expected that the composite CMC nonwovens will be a good candidate for wound dressing materials for mild exudate condition.     

Water and oil-repellent coatings of perfluoro-polyacrylate resins on cotton fibers: UV curing in comparison with thermal polymerization

UV curing of perfluoro-alkyl-polyacrylate resins able to impart water as well as oil-repellency to cotton fabrics was studied in comparison with conventional thermal polymerization. The process was assessed through weight gain and gel content measurements while the properties conferred to cotton fabrics were determined in terms of water and oil contact angles, moisture adsorption, and water vapor permeability. The polymerization yields were of the same order (>80 %) of those obtained with thermal curing as well as the high contact angles with water (>127°) and oil (>118°) even at low resin add-on (3 %). UV cured resins yielded oil contact angles mostly higher than 120° denoting super oil-repellent surfaces. Moreover the water and oil-repellency was adequately maintained after washing. The moisture adsorption of finished fabrics was lower than that of untreated cotton, but slightly higher for UV cured than thermally treated fabrics. Water vapor transmission rate showed that the finish treatment, thermal as well as by UV curing, does not reduce the breathability of the original cotton. DSC analysis demonstrated that the fiber pyrolysis is affected by the polymer add-on, while FTIR-ATR spectra of all finished fabrics showed typical peaks of ester and C-F groups. XPS analysis showed small differences between thermal and UV curing coatings with each resin, while coatings with the lowest percentage of fluorine groups did not affect the water and oil-repellency.     

Designing waterproof breathable materials based on electrospun nanofibers and assessing the performance characteristics

To develop waterproof breathable materials for diverse consumer applications, we used electrospinning to fabricate layered fabric systems with varying composite structures. Specifically, we developed layered fabric structures based on electrospun nanofiber webs with different levels of nanofiber web density, as well as different substrates and layer structures, and then examined the breathability and waterproofness of the material. The breathability and waterproofness of the layered fabric systems were compared with those of traditional waterproof breathable fabrics, including densely woven fabric, microporous membrane laminated fabric, and hydrophilic nonporous polyurethane coated fabric. Different breathability and barrier performance levels were achieved by varying the layer structure and substrates in the electrospun nanofiber web layered fabric systems. The uniformity of the nanofiber web and lamination process also affected the barrier and comfort performances. The comparison of waterproofness and breathability performances between the new materials and the traditional waterproof breathable materials revealed that the layered structures based on electrospun nanofiber webs provide a higher level of resistance to water penetration than densely woven fabrics and a higher degree of moisture vapor and air permeability than microporous membrane laminates and coated fabrics, with a proper selection of layer structure, substrate fabric, and lamination process.     

Synthesis,structure and thermal protective behavior of silica aerogel/PET nonwoven fiber composite

In recent years, flexible, mechanically strong and environmental friendly thermal insulation materials have attracted considerable attention. In this work, silica aerogel/polyethylene terephthalate (PET) nonwoven fiber composite with desirable characteristics was prepared via a two-step sol-gel process followed by an ambient drying method through immersing the PET nonwoven fiber into silica sol. The silica aerogel particles were characterized by FTIR, FE-SEM, TGA and nitrogen adsorption analysis. The morphology and hydrophobic properties of neat PET nonwoven fiber and its silica aerogel composite were also investigated. For studying thermal protective properties, the thermal diffusivity was calculated from temperature distribution curves. The mean pore size of 11 nm, the surface area of 606 m²/g and the total pore volume of 1.77 cm³/g for the silica aerogel particles in the composite are obtained from nitrogen adsorption analysis, indicating the aerogel can maintain its high porosity in the nonwoven composite structure. Silica aerogel particles were efficiently covered the surface of the PET fibers and completely filled the micron size pores of the nonwoven fiber leading to a stronger hydrophobicity and higher thermal insulation performance in the aerogel composite samples compared to the neat PET nonwoven. In this regard, an almost 64 % decrease in the thermal diffusivity was achieved with 66 wt% silica aerogel.     

Development of superhydrophobic polyester fabrics using alkaline hydrolysis and coating with fluorinated polymers

Alkaline hydrolysis is one of the most classic fiber finishing methods, however, its potential as tuning surface superhydrophobicity in mass scale has not been studied much. In this research, fine roughness was formed on the polyester fiber surfaces by alkaline hydrolysis at room temperature and fluorinated polymer mixtures were further coated. The developed superhydrophobic fabrics were evaluated in terms of structural changes, mechanical properties, surface hydrophobicity, and permeability for practical applications. As alkaline hydrolysis treatment time increased, surface roughness was increased as a lot of nano-craters were generated with the decrease of fabrics weight and tensile strength as well. As air pockets formed through nano-craters on the fiber surfaces, static contact angle increased, and shedding angle tended to decrease. In this study, the sample treated with alkaline hydrolysis for 20 minutes showed the highest static contact angle of 167.8±1.3° and lowest shedding angle of 4.4±2.3°. Considering tensile strength loss, however, the 15-minute alkaline hydrolyzed fabrics which showed static contact angle of 162.2±2.7° and shedding angle of 8.8±0.2° was selected as the optimal condition for practical application. The newly developed superhydrophobic fabrics were found to have higher water vapor and air permeability than those of untreated samples. At the same time, fluoropolymer coating played a certain role for tensile strength and water vapor permeability demonstrating the importance of understanding and designing proper fluorinated-compound treatment processes.     

Preparation of Copper Nanoparticles Coated Cotton Fabrics with Durable Antibacterial Properties

When copper nanoparticles (Cu NPs) were applied as an antimicrobial agent to finish cotton fabrics, there are two issues should be solved: the oxidization and the weak adsorbability onto cotton fiber surface. In the present work, we developed a new method that can achieve both immobilization and protection of the Cu NPs at the same time. As an effective binder, thioglycolic acid (TGA) was covalently linked to cotton fiber surface via an esterification with the hydroxyl groups of cellulose, then Cu NPs were introduced on the fabric surface in the presence of a protective reagent, citric acid. Due to the doubled stabilization acts of TGA and citric acid, the Cu NPs immobilized on the fabric surface showed an excellent antibacterial effect and outstanding laundering durability. Even after 50 consecutive laundering tests, the modified cotton fabrics still showed satisfactory antibacterial ability against both S. aureus and E. coli, which the bacterial reduction rates are all higher than 96 %. It is believed that this methodology has potential applications in a wide variety of textile productions such as sportswear, socks, and medical textiles.     

棉纤维的功能性技术研究进展

棉纤维是一种天然纤维素类大宗纤维,其性能优异及衍生物结构复杂,在棉织物等方面有着广泛应用;也是化学工业的重要原料.作者通过查阅文献资料,针对棉纤维的溶解、物理改性、化学改性方面的研究进展进行了综述,并分析了棉纤维功能性的改性技术发展趋势.同时,基于现有研究,梳理了今后研究者需要去解决的关键问题,为研究棉纤维功能性的改性...     

PVDF/Cu-BTC composite membranes for dye separation

Membranes with high water permeation capability as well as high rejection to dye molecules are very important for dye separation. In this study, a metal organic framework structure (Cu-BTC) was fabricated in situ on a poly(vinyl difluoride) hollow fiber support for nanofiltration of dye solution. In order to protect the Cu-BTC layer, the surface was coated by crosslinking polyvinyl alcohol. The composite membranes showed no rejection to divalent salts and high rejection to Congo Red dye. It was noticed that several Cu-BTC layers could enhance dye rejection of the composite membranes. This novel composite membrane showed promising applications in the separation of dye molecules from aqueous solutions containing dissolved salts.     

Developing UV-protective textiles based on electrospun zinc oxide nanocomposite fibers

This research investigates applying zinc oxide nanoparticles to polypropylene nonwoven fabrics via electrospinning for the development of UV-protective materials. Layered fabric systems with electrospun zinc oxide nanocomposite fiber webs were developed at various concentrations of zinc oxide in a range of web area densities. The effects of zinc oxide concentration and web area density on the UV-protective properties of layered fabric systems were examined. Air and moisture vapor transport properties of layered fabric systems were assessed to examine the effect of electrospun web layers on thermal comfort properties of the material. A very thin layer of electrospun zinc oxide nanocomposite fibers significantly increased the UV blocking for both UV-A and UV-B ranges, and exhibited an ultraviolet protection factor (UPF) of greater than 40, indicating excellent UV protection. UV-protective properties of layered fabric systems increased with increasing zinc oxide concentrations of the nanocomposite fiber web. Increasing the electrospun web area density of the zinc oxide nanocomposite fiber web also enhanced UV-protective properties of layered fabric systems. Air and moisture vapor transport properties of layered fabric systems decreased as the electrospun web area density increased for the range of web area densities examined.     

Coating Cellulosic Materials with Graphene for Selective Absorption of Oils and Organic Solvents from Water

Development of efficient and eco-friendly sorbents used for selective oil removal after oil spill disasters is one of the main topics in environmental science. By using various cellulosic materials coated with graphene flakes, using simple, one-step dip-coating method, it was possible to manufacture environmentally friendly, selective oil sorbents. The cellulosic materials of different yarn size and distribution such as cotton roving, gauze, fabric, and cellulosic wipe and Whatman filter paper were chosen. The scanning electron microscopy showed that simple dip-coating of any cellulosic materials into graphene dispersion creates a uniformly distributed nanomaterial coating. The wetting tests confirmed that the coating endowed cellulosic materials with hydrophobic properties, regardless of their initial yarn distribution and purity. Moreover, the water repellent samples were simultaneously highly sorptive towards oils and organic solvents. Sorption tests performed for a representative group of organic solvents and oils have shown that depending on cellulosic material the oil sorption capacity varied from 4 g/g to 33 g/g for cotton fabric and roving, respectively. Moreover, the absorption selectivity of chloroform versus water exceeded 90 % for each sample and reached over 99 % for the graphene coated cotton roving and gauze. Finally, the recyclability tests have shown that graphene coated materials are less fragile for reuse than naturally hydrophobic sorbents.     

Study on antibacterial and comfort performances of cotton fabric finished by chitosan-silver for intimate apparel

The fabric used for intimate apparel is widely required to have excellent antibacterial and comfort performances. In order to improve its antibacterial ability, this paper studied chitosan-silver finishing on the cotton knitted fabric. The study indicates that the chitosan-silver attached to the fabric exhibits excellent antibacterial action against the typical bacteria of Escherichia coli (E. coli) and Staphylococcus aureus (S. aureu). The anti-bacterial mechanism of chitosan-silver against E. coli and S. aureu were investigated. To guarantee its prominent comfort performance, measurements were made on the finished fabric of its air permeability, water vapor transmission, hydrophily, surface friction and bending ability against the control fabric, which is currently used for intimate apparel. The antibacterial and comfort performances were compared between the tested fabrics. The results show that the air permeability and the hydrophily of the finished cotton fabric are significantly better than the control one, while the water vapor transmission, the surface friction and the adjustable rate remain similar to each other. The bending rigidity of the finished fabric is slightly better due to the attachment of chitosan within accepted threshold. The dual compounding theory of chitosan-silver proves to be useful for a higher synergistic effect of anti-bacteria, lower whiteness degradation and overall optimization of comfort performance. This dual compounding theory of chitosan-silver is valuable for improving antibacterial and comfort performances of intimate apparel.     

Highly Durable and Robust Superhydrophobic/Superoleophilic Cotton Fabric with Well-designed Roughness for Oil/Water Separation

Herein we report a simple and reproducible method for fabricating highly durable and robust superhydrophobic and superoleophilic cotton fabrics via simultaneous radiation-induced graft polymerization of glycidyl methacrylate and subsequent chemical modifications with aminopropyltriethoxysilane and hexamethyldisilazane. The chemical structure and the surface topography of the pristine and the modified cotton fabrics were investigated in detail by ATR-FTIR, XPS, and ²⁹Si NMR, and a grafting layer was successfully immobilized onto the surface of the cotton fabric by forming covalent bonds. Multi-dimensional surface roughness was created by combining micro-sized fibers of the cotton fabric, nanoscaled protuberances of the grafting chain, and molecular level spherical projection points of silicon methyl. The superhydrophobic cotton fabric exhibited long-term stability, ultra-high durability and robustness, and maintained its properties even after 25 wash cycles. The fabric also showed excellent water repellency with a water contact angle of 153 ° and a high efficiency of oil/water separation (98 %). The superhydrophobic/superoleophilic cotton fabric developed in the present work exhibits important potential applications in superhydrophobic textiles and oil/water separation.     

Naringin-loaded Poly(ε-caprolactone)/Gelatin Electrospun Mat as a Potential Wound Dressing: In vitro and In vivo Evaluation

In the present study, naringin, a flavonoid isolated from the grape and citrus fruit species, was incorporated with poly(ε-caprolactone)/gelatin composite mats in order to develop a potential wound dressing. The composite mats were prepared by electrospinning of poly(ε-caprolactone)/gelatin (1:1 (w/w)) solution incorporated with 1.50 %, 3 % and 6 % (w/w) of naringin. The electrospun mats were evaluated regarding their morphology, contact angle, water-uptake capacity, water vapor transmission rate, tensile properties, drug release, cellular response and in vivo wound healing activity. The study showed that after 2 weeks, the full-thickness excisional wounds of Wistar rats treated with the naringin-loaded dressings achieved a wound closure of higher than 94 % and the dressing containing 6 % (w/w) naringin had almost 100 % wound closure. The sterile gauze, as the control group, showed nearly 86 % of wound closure after this period of time. Our results provided evidence that supports the possible applicability of naringin-loaded wound dressing for successful wound treatment.     

Preparation of Durable Antibacterial Cellulose with AgCl Nanoparticles

In this study, a facile method was developed to coat AgCl nanoparticles (NPs) onto knitted cotton fabrics. The AgCl NPs were characterized by ultraviolet absorption spectrum, X-ray diffraction (XRD) and dynamic laser light scattering (DLS). The AgCl NPs were coated onto cotton fabrics through a pad-dry-cure process with the assistance of 1,2,3,4- butanetetracarboxylic acid (BTCA). Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), ICP-OES analysis and energy-dispersive X-ray spectroscopy (EDX) confirmed that AgCl NPs were successfully coated onto cotton fabrics. The prepared cotton samples exhibited excellent antimicrobial activity against both Gram-positive S. aureus and Gram-negative K. pneumonia bacteria. Rat skin fibroblast cytotoxicity testing demonstrated the treated cotton fabrics to be non-toxic. The washing durability evaluation showed that the antimicrobial function of cotton fabrics was durable to washing. In addition, the wrinkle resistance of the coated cotton fabrics was improved and there was no obvious change in whiteness.