苦楝素提取方法的比较研究

对比研究了从苦楝树皮中提取苦楝素的几种方法,通过实验,得出了不同提取方法的最佳条件。超临界CO2萃取在萃取温度45℃、压力20MPa、夹带剂为60%乙醇的情况下萃取2h,苦楝素的萃取率为0.850%;微波辅助提取法,以60%乙醇为溶剂,料液比为1∶9(g∶mL,下同),微波功率340W,辐射时间40s×3次,苦楝素的提取率为0.693%;超声波提取法,以60%乙醇为溶剂,料液比为1∶9,超声波作用时间为30min,超声波功率为200W,苦楝素的提取率为0.715%。将上述3种提取方法与传统的有机溶剂提取法进行详细的比较,结果表明:对于苦楝素提取,超声波提取法最好。     

杜仲叶总多酚超声波-微波辅助提取及其抗氧化活性研究

采用超声波-微波辅助法优化杜仲叶中总多酚提取工艺,并考察其抗氧化活性。通过Plackett-Burman试验考察了乙醇体积分数、料液比、微波功率、微波处理时间、超声波功率和超声波处理时间6个因素对杜仲叶总多酚提取效果的影响,筛选得到乙醇体积分数、料液比、微波功率和超声波处理时间4个显著影响因素,在此基础上,通过最陡爬坡试验和响应面试验得到最佳提取条件为:乙醇体积分数为46%,料液比为1∶20.70(g∶mL),微波功率为154 W,微波处理时间140 s,超声波功率350 W,超声波处理时间为31 min。在此条件下提取2次总多酚得率达8.491%,与传统溶剂提取法相比,总多酚得率提高33.57%。利用最优工艺得到总多酚提取物,其体外抗氧化试验表明:杜仲叶总多酚提取物对1,1-二苯基-2-三硝基苯肼自由基(DPPH·)、2,2-联氮-二-3-乙基-苯并噻唑-6-磺酸自由基(ABTS·)和羟基自由基(·OH)均有较强的清除能力,其半数抑制质量浓度(IC_(50))分别为31.21、24.50和311.8 mg/L,抗氧化活性与BHT相当,低于Vc。     

微波辅助提取兴安落叶松木材中阿拉伯半乳聚糖的工艺研究

以兴安落叶松(Larix gmelinii Rupr.)木材的加工剩余物为原料,以水为溶剂,微波辅助提取阿拉伯半乳聚糖.通过对影响提取率的主要因素微波作用时间、微波功率、料液比和木粉粒度等进行正交试验,分析得出微波辅助提取阿拉伯半乳聚糖的较佳工艺参数为10.0 g兴安落叶松木粉,微波功率210 W,微波作用时间35 min,料液质量比1∶35,木粉粒度0.2～0.3 mm时, 阿拉伯半乳聚糖提取率17.47 %,比传统水浴浸提法高1.6 %,时间仅为原来的1/10.用红外和紫外光谱分析两种方法所得产物的化学结构相同,微波辅助提取的粗糖中杂质含量比传统水浴法低.实验结果表明,对于兴安落叶松木材中阿拉伯半乳聚糖的提取,微波辅助提取优于传统水浴浸提法.     

高黎贡山糯橄榄多酚的提取方法改进及工艺优化

以低温烘干的高黎贡山糯橄榄为原料,采用微波辅助对高黎贡山糯橄榄中的多酚类物质进行提取。在单因素试验的基础上,使用正交试验设计考察了微波时间、微波功率、料液比、乙醇浓度等对多酚提取得率的影响。结果表明,最佳提取工艺条件为微波时间30s、微波功率640W、料液比1︰30g/mL、乙醇浓度50%。该研究结果为高黎贡山糯橄榄中多酚的高效提取和工业化生产提供依据。     

桑叶总多酚筛选和分离纯化工艺研究

采用超声波和微波协同提取桑叶总多酚,Folin-Ciocalte法分析不同品种桑叶的总多酚含量,运用单因素试验和响应面法优化提取工艺,并考察不同种类大孔树脂对桑叶总多酚的纯化效果。结果表明,18个品种桑叶中大墨斗的总多酚质量分数最高,达到2.072%;灃24×苗33总多酚质量分数最低,仅为1.035%。湖桑87桑叶总多酚最佳提取工艺为:1 g桑叶粉末,液料比20∶1(mL∶g),提取时间93 s,微波功率326 W,超声波功率304 W,粗提物得率为14.7%,纯度为10.87%。筛选得到的较适合桑叶总多酚纯化的H103树脂的吸附量为15.57 mg/g,解吸率为88.67%,且较短时间内达到吸附平衡与解吸平衡。上样时吸附柱体积40 mL,上样量15 g粗提物,桑叶总多酚的最佳质量浓度为3 g/L,此时最佳洗脱条件为乙醇体积分数60%、洗脱流速2 mL/min、洗脱体积80 mL,此条件下,桑叶总多酚纯度由10.87%提高到65.45%,纯化过程中桑叶总多酚得率为84.7%。     

超声波辅助提取旱柳树叶中的总黄酮

以旱柳落叶为原料,60 % 乙醇(质量分数,下同)为提取剂,芦丁为标准对照品,研究探索了柳叶中总黄酮的溶剂提取法和超声波辅助提取法的最佳提取条件,并对两种提取方法的提取效果进行了比较.试验表明,溶剂提取法的最佳提取条件为:0.3 g柳叶粉末以60 %乙醇为溶剂,料液比1:35(g:mL,下同),65 ℃提取3次,每次75 min,总黄酮得率3.83%;超声波辅助提取的最佳条件为:0.3 g柳叶粉末以60%乙醇为溶剂,料液比1:35,超声波功率400 W,超声波处理3次,每次30 min,总黄酮得率4.26%.超声波辅助提取比单纯的溶剂提取缩短了60 %的提取时间,得率却提高了11.23 %.     

微波和超声波辅助提取桃仁油工艺的比较研究

为了提高桃加工副产物的综合利用,以桃仁为原料,采用微波辅助法和超声波辅助法提取桃仁油,通过单因素和正交试验优化了提取工艺,并对桃仁油的理化性质、脂肪酸组成、主要官能团结构、热力学性质及风味进行分析,以比较不同提取方法对桃仁油成分和性质的影响。研究结果表明:10 g桃仁粉,以石油醚(60～90℃)为提取溶剂,微波辅助提取桃仁油的最佳工艺条件为提取时间25min,温度75℃,微波功率400 W,液料比11∶1(mL∶g),此时桃仁油得率为49.23%;超声波辅助提取桃仁油的最佳工艺条件为温度75℃,液料比11∶1(mL∶g),超声波功率500 W,提取时间40min,此时桃仁油得率为48.56%。2种提取方法的桃仁油得率虽然略低于索氏提取的51.87%,但是提取时间明显缩短、提取效率显著提高。同时2种提取方法所得桃仁油的理化性质、脂肪酸组成、官能团结构、热力学性质及风味等与索氏提取法均无显著差异。桃仁油主要含有油酸、亚油酸和棕榈酸等,其中油酸和亚油酸GC含量最高,二者之和达93%以上。     

油茶籽多酚微波辅助提取响应面法的优化

多酚是油茶籽中重要的活性成分。研究其组成、提取工艺和活性,对于优质茶油的生产具有重要意义。在单因素试验的基础上,采用响应面法就微波辅助提取油茶籽多酚进行了优化试验,优化了提取工艺参数。结果表明:微波功率、微波提取时间、料液比这3个因素对油茶籽多酚提取效果的影响均达到了显著水平;微波功率与微波提取时间、微波功率与料液比、微波提取时间与料液比之间的交互作用显著。利用DesignExpert7.1软件分析得出的油茶籽微波提取的最佳工艺参数为:微波功率,800W;提取时间,35s;料液比为1︰16。在此条件下,用回归模型预测的油茶籽多酚的提取量为19.60mg·g-1,实际测得值为19.02mg·g-1,相对误差为3%。与传统溶剂提取法相比,微波提取法具有时间短、效果好的特点。     

板栗多糖提取工艺的研究

分别采用热水浸提法、超声波辅助提取法两种工艺提取板栗多糖,经乙醇沉淀、Sevage法除蛋白、有机溶剂脱脂后用蒽酮-硫酸比色法测定其含量,通过单因素试验和正交试验确定不同工艺的最佳提取工艺参数.结果表明:1 g板粟粉,热水浸提法提取板栗多糖的最佳条件为提取温度60℃,提取时间1.5 h,液料比20∶1(mL∶g),板栗多...     

微波辅助提取兴安落叶松木材中阿拉伯半乳聚糖的工艺研究

以兴安落叶松(Larix gmelinii Rupr．)木材的加工剩余物为原料．以水为溶剂，微波辅助提取阿拉伯半乳聚糖。通过对影响提取率的主要因素微波作用时间、做波功率、料液比和木粉粒度等进行正交试验．分析得出微波辅助提取阿拉伯半乳聚糖的较佳工艺参数为10．0g兴安落叶松木粉。微波功率210W。微波作用时间35min。料液质量比1：35．木粉粒度0．2～0．3mm时．阿拉伯半乳聚糖提取率17．47％。比传统水浴浸提法高1．6％，时间仅为原来的1/10。用红外和紫外光谱分析两种方法所得产物的化学结构相同。微波辅助提取的粗糖中杂质含量比传统水浴法低。实验结果表明．对于兴安落叶松木材中阿拉伯半乳聚糖的提取．微波辅助提取优于传统水浴浸提法。     

Browsing Damage on Pine (Pinus sylvestris and P. contorta) by a migrating moose (Alces alces) Population in Winter: Relation to Habitat Composition and Road Barriers

In Scandinavia, moose (Alces alces L.) sometimes cause severe browsing damage to economically-important pine. Moose-vehicle accidents have spurred construction of fences along roads, and these may interfere with moose migration between summer and winter ranges, or the road alone may be a barrier. If this happens and moose build up along roads, landowners may suffer economically. Therefore, this study investigated whether roads, fences or other factors influence the use of young pine stands by moose. Eighty stands along roads in northern Sweden were evaluated in which individually-browsed branches were counted on 9972 pines. Moose browsing was not significantly related to birch (Betula pendula Roth, B. pubescens Ehrh.) density, nor did it differ between pines (Pinus contorta Douglas or P. sylvestris L.). However, increased pine density, site productivity and proximity to a highway were associated with increased browsing. Further large-scale studies are needed to understand moose habitat selection and the effects of roads.     

Effects of Root Freezing on the Physiology and Growth of Picea glauca,Picea mariana and Pinus banksiana Seedlings Under Different Soil Moisture Regimes

The root systems of 2-yr-old Picea glauca, Picea mariana and Pinus banksiana seedlings were submitted to various frost temperatures during an artificial frost to induce different levels of root damage. Frost-damaged and control seedlings were placed in a greenhouse under high and low soil moisture regimes. Seedling growth and physiology were evaluated periodically. Seedling survival was reduced when root damage reached levels of 60-80%. Root systems of all three species showed partial to total recovery by the end of the experiment. In general, root freezing damage caused reductions in seedling growth, with these reductions becoming less significant over time. Root damage had little to no effect on black spruce and jack pine seedling physiology, while white spruce CO 2 uptake decreased with increasing root damage. Shoot nitrogen content of all three species decreased slightly with increasing root damage.     

Stand Structure in Pine,Spruce and Deciduous Forests: A Comparison Between Finnish and Russian Karelia

This study investigated the stand structure in pine, spruce and deciduous forests in the border district of Finland and Russia. A total of 46 mature forest stands was selected as pairs, the members of each pair being as similar as possible with respect to their forest site type, age, moisture and topography. The stands were then compared between the two countries by means of basal areas and number of stems. The proportions of dominating tree species were 2-12% lower, and correspondingly the proportions of secondary tree species higher, in Russian forests. The density of the forest stock was also higher in each forest type in Russia. The forests in the two countries differed most radically in terms of the abundance of dead trees. The amount was two to four times higher in Russian deciduous and spruce forests, and in pine forests the difference was 10-fold. The stand structures indicated that Russian coniferous stands, in particular, were more heterogeneous than intensively managed pine and spruce stands in Finland.     

Growth and Terminal Bud Formation in Picea abies Seedlings Grown with Alternating Diurnal Temperature and Different Light Qualities

The root collar diameter and the height:diameter ratio are of particular importance in container-grown seedlings where a high density in the containers may produce spindly seedlings. Temperature regimes and light quality are known to affect plant growth. The aim of this study was to identify responses in Picea abies (L.) Karst. seedlings grown with light providing different red:far-red ratios and under temperature regimes with alternating day (DT) and night temperature (NT) from negative (DT < NT) to positive (DT > NT) difference (DIF) between DT and NT. Experiments were conducted in controlled environment chambers and in a daylight phytotron. Only limited thermoperiodic responses appeared in P . abies seedlings with respect to seedling height and dry weight accumulation. The formation of terminal buds, however, was clearly delayed in seedlings grown at negative DIF. The results indicate a requirement for day extension light that is high in far-red, to prevent terminal bud formation under natural short-day conditions. An extended study should be conducted to clarify the minimum level of light intensity and the optimal light quality needed to prevent terminal bud formation under natural short-day conditions.     

CAD与建筑设计的关系

本文分析了CAD在设计中引起的正面和负面影响,并进行了系统的阐述,从而使设计者在应用中能够保持客观的态度。     

Natural Regeneration in Clear-cuts: Effects of Scarification,Slash Removal and Clear-cut Age

The effects of soil scarification (mounding), slash removal and clear-cut age on the natural regeneration in clear-cuts was evaluated using data from four sites in southern Sweden. The treatments were carried out during a good seed and establishment year for birch ( Betula pubescens Ehrh. and B. pendula Roth). Scarification had the strongest positive effect on the density of naturally regenerated seedlings, especially in birch, but also in pine ( Pinus sylvestris L.) and spruce [ Picea abies (L.) Karst]. Slash removal had a positive effect on birch density. No statistically significant effect of clear-cut age was found. In addition, no statistically significant interactions between clear-cut age and scarification or slash removal were found. The ingrowth of field vegetation was the fastest in areas that were not scarified, less rapid in areas scarified on old clear-cuts, and the slowest after scarification in fresh clear-cuts. In conclusion, it may be possible to control the density of birch during a good establishment year for birch. If birch is desired, the best combination of treatments is to remove the slash and scarify; otherwise, these treatments should be avoided.     

Risk Perception Among Non-industrial Private Forest Owners

Based on an enquiry, risk perception among non-industrial private forest owners is described in relation to climate change and forestry hazards. Of the respondents, 11% took action to remedy the effects of climate change. Out of a given set, hazards were ranked according to each respondent's experience of recent substantial financial loss to the estate and in relation to his or her willingness to make investments aimed at risk reduction. For each hazard, the respondent assessed the risk in four classes ranging from very high to negligible risk. Six hazards were considered most problematic in all three aspects: browsing damage, falling timber prices, damage by wind, spruce bark beetle, root rot and pine weevil. A majority of the respondents claimed to take action to reduce the risk associated with at least one hazard, while 35% did not know whether they did. Excluding climate change, the need for decision support was the largest in relation to damage by wind owing to a combination of perceived high risk and a high level of ignorance in relation to whether risk-reducing measures were taken.     

Interactions in decomposition and N mineralization between tropical legume residue components

In situ produced plant residues contain a mixture of different plant components of varying quality. To assess synergistic or antagonistic interactions occurring during the decomposition and mineralization of such mixtures, individual plant parts (stems, leaves, leaf litter and roots) or the mixture of stems, leaves and leaf litter of the agroforestry species pigeonpea (Cajanus cajan) or of crop residues of peanut (Arachis hypogaea) or of the weed hairy indigo (Indigofera hirsuta) were incubated in pots for 19 weeks. Periodically, remaining plant residues were sieved out (>2 mm), weighed and N content as well as soil mineral N determined. Above- and below-ground residues of peanut decomposed fastest and showed the largest N release in agreement with their high N concentration and low-acid detergent fibre (ADF) : N ratio. Hairy indigo was hypothesized to be of lower quality than pigeonpea because of its high-polyphenol content. However, it decomposed faster than pigeonpea, largely because of the higher N and lower lignin concentration of its components. Ranking of individual plant components for N mineralization resulted in the following pattern, leaves > leaf litter > roots > stems. In mixtures of the different plant components a similar species order in decomposition was obtained, e.g. peanut > hairy indigo > pigeonpea. The amount of N released from the mixture was dominated by stem material that comprised 46–61% of the mixture. The interactions in mixtures were relatively small for peanut (generally high-quality components) as well as for pigeonpea (low proportion of high-quality components, i.e. N rich leaf material). However, a positive interaction occurred during later stages of N mineralization in the mixture of hairy indigo as it had a significant proportion of N rich components and absence of highly reactive polyphenols. Thus, for plants with low to intermediate chemical quality attributes, manipulating plant composition (e.g. by varying harvest age, affecting stem and leaf proportions) will be important to obtain significant interactions during decomposition when its components are mixed.     

Pasture production and tree growth in a young pine plantation fertilized with inorganic fertilizers and milk sewage in northwestern Spain

The use of organic waste materials such as milk sewage as an organic fertilizer could have the dual advantages of organic-waste disposal and reduced dependence on inorganic fertilizers. The effects of fertilization with (1) conventional mineral fertilization, (2) milk sewage sludge at 40 kg N ha⁻¹ target rate and (3) no fertilization on pasture production and tree growth were examined in an experiment consisting of two pasture mixtures under a one-year-old Pinus radiata plantation with a density of 2500 trees ha⁻¹. The two pasture mixtures were: (1) Dactylis glomerata L. var. saborto (25 kg ha⁻¹) + Trifolium repens L. group Ladino (4 kg ha⁻¹) + Trifolium pratense L. var. Marino (1 kg ha⁻¹); (2) Lolium perenne L. var. Tove (25 kg ha⁻¹) + Trifolium repens L. group Ladino (4 kg ha⁻¹) + Trifolium pratense L. var. Marino (1 kg ha⁻¹). The experiment began in the spring of 1995 using a randomized block design with three replicates in Castro Riberas de Lea (Lugo, Galicia, north-western Spain). Plot size was 12 × 8 m², with a 1 m buffer strip between plots. Two-year data showed that fertilization with either material had a positive effect on pasture production, with no significant difference between the two fertilization treatments. Tree growth in the milk sewage sludge plot was significantly higher than in the control plots. Inorganic fertilization increased pasture production, but affected tree growth negatively. The results show that milk sewage sludge could be used as a fertilizer in silvo-pastoral systems. This revised version was published online in June 2006 with corrections to the Cover Date.