Physical and oxidative stability of fish oil-in-water emulsions stabilized with beta-lactoglobulin and pectin

The oxidation of fatty acids can be inhibited by engineering the surface of oil-in-water emulsion droplets to decrease interactions between aqueous phase prooxidants and lipids. The objective of this research was to evaluate whether emulsions stabilized by a multilayer emulsifier systems consisting of beta-lactoglobulin and citrus or sugar beet pectin could produce fish oil-in-water emulsions that had good physical and oxidative stability. Sugar beet pectin was compared to citrus pectin because the sugar beet pectin contains the known antioxidant, ferulic acid. A primary Menhaden oil-in-water emulsion was prepared with beta-lactoglobulin upon which the pectins were electrostatically deposited at pH 3.5. Emulsions prepared with 1% oil, 0.05% beta-lactoglobulin, and 0.06% pectins were physically stable for up to 16 days. As determined by monitoring lipid hydroperoxide and headspace propanal formation, emulsions prepared with the multilayer system of beta-lactoglobulin and citrus pectin were more stable than emulsions stabilized with beta-lactoglobulin alone. Emulsions prepared with the multilayer system of beta-lactoglobulin and sugar beet pectin were less stable than emulsions stabilized with beta-lactoglobulin alone despite the presence of ferulic acid in the sugar beet pectin. The lower oxidative stability of the emulsions with the sugar beet pectin could be due to its higher iron and copper concentrations which would produce oxidative stress that would overcome the antioxidant capacity of ferulic acid. These data suggest that the oxidative stability of oil-in-water emulsions containing omega-3 fatty acids could be improved by the use of multilayer emulsion systems containing pectins with low metal concentrations.     

Production and characterization of oil-in-water emulsions containing droplets stabilized by beta-lactoglobulin-pectin membranes

Oil-in-water emulsions containing droplets stabilized by beta-lactoglobulin (beta-Lg)-pectin membranes were produced using a two-stage process. A primary emulsion containing small droplets (d(32) approximately 0.3 microm) was prepared by homogenizing 10 wt % corn oil with 90 wt % aqueous solution (1 wt % beta-Lg, 5 mM imidazole/acetate buffer, pH 3.0) using a high-pressure valve homogenizer. The primary emulsion was then diluted with pectin solutions to produce secondary emulsions with a range of pectin concentrations (5 wt % corn oil, 0.45 wt % beta-Lg, 5 mM imidazole/acetate buffer, 0-0.22 wt % pectin, pH 3.0). The electrical charge on the droplets in the secondary emulsions decreased from +33 +/- 3 to -19 +/- 1 mV as the pectin concentration was increased from 0 to 0.22 wt %, which indicated that pectin adsorbed to the droplet surfaces. The mean particle diameter of the secondary emulsions was small (d(32) < 1 microm) at relatively low pectin concentrations (<0.04 wt %), but increased dramatically at higher pectin concentrations (e.g., d(32) approximately 13 microm at 0.1 wt % pectin), which was attributed to charge neutralization and bridging flocculation effects. Emulsions with relatively small mean particle diameters (d(32) approximately 1.2 microm at 0.1 wt % pectin) could be produced by disrupting flocs formed in secondary emulsions containing highly negatively charged droplets, for example, by sonication, blending, or homogenization. The particles in these emulsions probably consisted of small flocs containing a number of protein-coated droplets bound together by pectin molecules. These emulsions had good stability to further particle aggregation up to relatively high ionic strengths (< or =500 mM NaCl) and low pH (pH 3). The interfacial engineering technology used in this study could lead to the creation of food emulsions with improved physicochemical properties or stability.     

Role of proteins in oil-in-water emulsions on the stability of lipid hydroperoxides

The purpose of this research was to better understand the mechanisms by which proteins affect the rates of lipid oxidation in order to develop protein-stabilized emulsion delivery systems with maximal oxidative stability. This study evaluated the affect of pH and emulsifier concentration on the stability of cumene hydroperoxide in hexadecane-in-water emulsions stabilized by beta-lactoglobulin (beta-Lg). Emulsions prepared with 0.2 wt % beta-Lg (at pH 7.0) showed a 26.9% decrease in hydroperoxide concentrations 5 min after 0.25 mM ferrous ion was added to the emulsion. EDTA, but not continuous phase beta-Lg, could inhibit iron-promoted lipid hydroperoxide decomposition. Lipid hydroperoxides were more stable to iron-promoted degradation at pH values below the pI of beta-Lg, where the emulsion droplet would be cationic and thus able to repel iron away from the lipid hydroperoxides. Heating the beta-Lg-stabilized emulsions to produce a cohesive protein layer on the emulsion droplet surface did not alter the ability of iron to decompose lipid hydroperoxides. These results suggest that proteins at the interface of emulsion droplets primarily stabilize lipid hydroperoxides by electrostatically inhibiting iron-hydroperoxide interactions.     

Influence of sucrose on droplet flocculation in hexadecane oil-in-water emulsions stabilized by beta-lactoglobulin

The influence of sucrose on the flocculation stability of hydrocarbon oil-in-water emulsions stabilized by a globular protein was examined using laser diffraction. Salt (150 mM NaCl) and sucrose (0-40 wt %) were added to n-hexadecane oil-in-water emulsions stabilized by beta-lactoglobulin (beta-Lg, pH 7.0) either before or after isothermal heat treatment (30-95 degrees C for 20 min). When salt was added to emulsions before heat treatment, appreciable droplet flocculation was observed below the thermal denaturation temperature of the adsorbed beta-Lg (T(m) approximately 70 degrees C), and more extensive flocculation was observed above T(m). On the other hand, when salt was added to emulsions after heat treatment, appreciable droplet flocculation still occurred below T(m), but little flocculation was observed above T(m). Addition of sucrose to the emulsions increased T(m) and either promoted or suppressed droplet flocculation depending on whether it was added before or after heat treatment. These results are interpreted in terms of the influence of sucrose on protein conformational stability, protein-protein interactions, and the physiochemical properties of aqueous solutions. This study has important implications for the formulation and production of protein stabilized oil-in-water emulsions.     

Interface characterization and aging of bovine serum albumin stabilized oil-in-water emulsions as revealed by front-surface fluorescence

This paper is devoted to the application of front-surface fluorescence to the study of aging and oxidation of oil-in-water emulsions. Emulsions with two oil droplet sizes were stabilized with bovine serum albumin (BSA) and stored at 37 or 47 degrees C. Lipid oxidation was demonstrated by measurement of hydroperoxides and headspace pentane. Front-surface fluorescence spectra (excitation wavelength = 355 nm) revealed gradual formation of oxidized lipid-protein adducts during the 4 weeks of storage. Fluorescence (excitation = 290 nm) of BSA tryptophanyl residues (Trp) declined during the first day of aging and then decreased slightly and linearly. Fourth-derivative Trp spectra exhibited peaks at 316 and 332 nm. Their evolution indicated that the ratio of Trp in hydrophobic environments to total Trp increased in small droplet emulsions. This suggests that, during lipid oxidation, the adsorbed and nonadsorbed protein underwent various degrees of Trp degradations, polymerization, and aggregation. Thus, front-surface fluorescence makes it possible to evaluate, noninvasively, protein modification and lipid oxidation end-products during processing and storage of food emulsions.     

Impact of protein surface denaturation on droplet flocculation in hexadecane oil-in-water emulsions stabilized by beta-lactoglobulin

The influence of globular protein denaturation after adsorption to the surface of hydrocarbon droplets on flocculation in oil-in-water emulsions was examined. n-Hexadecane oil-in-water emulsions (pH 7.0) stabilized by beta-lactoglobulin (1-wt % beta-Lg) were prepared by high-pressure valve homogenization. NaCl (0-150 mM) was added to these emulsions immediately after homogenization, and the evolution of the mean particle diameter (d) and particle size distribution (PSD) was measured by laser diffraction during storage at 30 degrees C for 48 h. No change in d or PSD was observed in the absence of added salt, which indicated that these emulsions were stable to flocculation. When 150 mM NaCl was added to emulsions immediately after homogenization, d increased rapidly during the following few hours until it reached a plateau value, while the PSD changed from monomodal to bimodal. Addition of N-ethylmaleimide, a sulfhydryl blocking agent, to the emulsions immediately after homogenization prevented (at 20 mM NaCl) or appreciably retarded (at 150 mM NaCl) droplet flocculation. These data suggests that protein unfolding occurred at the droplet interface, which increased the hydrophobic attraction and disulfide bond formation between droplets. In the absence of added salt, the electrostatic repulsion between droplets was sufficient to prevent flocculation, but in the presence of sufficient salt, the attractive interactions dominated, and flocculation occurred.     

Lipid oxidation in corn oil-in-water emulsions stabilized by casein,whey protein isolate,and soy protein isolate

Proteins can be used to produce cationic oil-in-water emulsion droplets at pH 3.0 that have high oxidative stability. This research investigated differences in the physical properties and oxidative stability of corn oil-in-water emulsions stabilized by casein, whey protein isolate (WPI), or soy protein isolate (SPI) at pH 3.0. Emulsions were prepared with 5% corn oil and 0.2-1.5% protein. Physically stable, monomodal emulsions were prepared with 1.5% casein, 1.0 or 1.5% SPI, and > or =0.5% WPI. The oxidative stability of the different protein-stabilized emulsions was in the order of casein > WPI > SPI as determined by monitoring both lipid hydroperoxide and headspace hexanal formation. The degree of positive charge on the protein-stabilized emulsion droplets was not the only factor involved in the inhibition of lipid oxidation because the charge of the emulsion droplets (WPI > casein > or = SPI) did not parallel oxidative stability. Other potential reasons for differences in oxidative stability of the protein-stabilized emulsions include differences in interfacial film thickness, protein chelating properties, and differences in free radical scavenging amino acids. This research shows that differences can be seen in the oxidative stability of protein-stabilized emulsions; however, further research is needed to determine the mechanisms for these differences.     

Stabilization of oil-in-water emulsions by beta-lactoglobulin-polyethylene glycol conjugates

The disulfide bonds of beta-lactoglobulin (beta-lg) were modified by oxidative sulfitolysis to generate beta-lgSO(3). The native protein (beta-lg) and the modified protein (beta-lgSO(3)) were conjugated to activated polyethylene glycol (PEG) to generate beta-lgPEG and beta-lgSO(3)PEG, respectively. Oil-in-water (o/w) emulsions containing 1% beta-lg or beta-lg conjugates were prepared at pH 2.8, 5.0, and 7.0. Emulsion droplet diameters and zeta potentials were measured. For the same emulsifier, emulsion droplet diameters decreased when emulsion pH increased. Zeta potentials of emulsion droplets increased with pH for beta-lg and beta-lgSO(3). Zeta potentials of beta-lgPEG and beta-lgSO(3)PEG approached zero, suggesting that the protein molecule was covered by PEG chains. Accelerated and 7-day storage stabilities at 21 degrees C of the emulsions were monitored. The emulsifying activity index (EAI) of beta-lgPEG was not significantly different from the EAI of beta-lg. The EAI of beta-lg was enhanced following sulfitolysis of beta-lactoglobulin. The emulsifying activity increased more when the oxidatively modified protein was conjugated to polyethylene glycol. Emulsions made with beta-lgSO(3)PEG were more stable than emulsions made with beta-lg, beta-lgPEG, or beta-lgSO(3) under accelerated stability study and for 7 days at 21 degrees C. The stability of o/w emulsions stabilized with beta-lgSO(3)PEG increased because individual droplets were better protected, against protein bridging or coalescence, by the thick adsorbed protein-PEG layer.     

Stabilization of oil-in-water emulsions by cod protein extracts

The ability of two protein fractions extracted from cod to form and stabilize oil-in-water emulsions was examined: a high salt extracted fraction (HSE protein) and a pH 3 acid extracted fraction (AE protein). Both fractions consisted of a complex mixture of different proteins, with the predominant one being myosin (200 kDa). The two protein fractions were used to prepare 5 wt % corn oil-in-water emulsions at ambient temperature (pH 3.0, 10 mM citrate-imidazole buffer). Emulsions with relatively small mean droplet diameters (d(3,2) < 1 microm) and good creaming stability (> 9 days) could be produced at protein concentrations > or =0.2 wt % for both fractions. The isoelectric point of droplets stabilized by both protein fractions was pH approximately 5. The emulsions were stable to droplet flocculation and creaming at relatively low pH (< or =4) and NaCl concentrations (< or =150 mM) when stored at room temperature. In the absence of salt, the emulsions were also stable to thermal treatment (30-90 degrees C for 30 min), but in the presence of 100 mM NaCl droplet flocculation and creaming were observed in some of the emulsions, particularly those stabilized by the AE fraction. The results suggest that protein fractions extracted from cod can be used as emulsifiers to form and stabilize food emulsions.     

Impact of whey protein emulsifiers on the oxidative stability of salmon oil-in-water emulsions

To obtain a better understanding of how the interfacial region of emulsion droplets influences lipid oxidation, the oxidative stability of salmon oil-in-water emulsions stabilized by whey protein isolate (WPI), sweet whey (SW), beta-lactoglobulin (beta-Lg), or alpha-lactalbumin (alpha-La) was evaluated. Studies on the influence of pH on lipid oxidation in WPI-stabilized emulsions showed that formation of lipid hydroperoxides and headspace propanal was much lower at pH values below the protein's isoelectric point (pI), at which the emulsion droplets were positively charged, compared to that at pH values above the pI, at which the emulsion droplets were negatively charged. This effect was likely due to the ability of positively charged emulsion droplets to repel cationic iron. In a comparison of lipid oxidation rates of WPI-, SW-, beta-Lg-, and alpha-La-stabilized emulsions at pH 3, the oxidative stability was in the order of beta-Lg > or = SW > alpha-La > or = WPI. The result indicated that it was possible to engineer emulsions with greater oxidative stability by using proteins as emulsifier, thereby reducing or eliminating the need for exogenous food antioxidants.     

Role of continuous phase protein on the oxidative stability of fish oil-in-water emulsions

Whey protein isolate (WPI), soy protein isolate (SPI), and sodium caseinate (CAS) can inhibit lipid oxidation when they produce a positive charge at the interface of emulsion droplets. However, when proteins are used to stabilize oil-in-water emulsions, only a fraction of them actually absorb to the emulsion droplets, with the rest remaining in the continuous phase. The impact of these continuous phase proteins on the oxidative stability of protein-stabilized emulsions is not well understood. WPI-stabilized menhaden oil-in-water emulsions were prepared by high-pressure homogenization. In some experiments WPI was removed from the continuous phase of the emulsions through repeated centrifugation and resuspension of the emulsion droplets (washed emulsion). Unwashed emulsions were more oxidatively stable than washed emulsions at pH 7.0, suggesting that continuous phase proteins were antioxidative. The oxidative stability of emulsions containing different kinds of protein in the continuous phase decreased in the order SPI > CAS > WPI, as determined by both hydroperoxide and headspace propanal formation. Iron-binding studies showed that the chelating ability of the proteins decreased in the order CAS > SPI > WPI. The free sulfhydryls of both WPI and SPI were involved in their antioxidant activity. This research shows that continuous phase proteins could be an effective means of protecting omega-3 fatty acids from oxidative deterioration.     

Influence of pH and iota-carrageenan concentration on physicochemical properties and stability of beta-lactoglobulin-stabilized oil-in-water emulsions

The influence of pH and iota-carrageenan concentration on the properties of beta-lactoglobulin (beta-Lg)-stabilized oil-in-water emulsions was investigated by measuring the particle charge, particle size distribution, and creaming stability. Emulsions containing droplets stabilized by beta-Lg were produced by homogenization, and then, iota-carrageenan was added. At pH 3, the droplet charge did not change for iota-carrageenan concentrations 相似文献   

Antioxidant activity of a proanthocyanidin-rich extract from grape seed in whey protein isolate stabilized algae oil-in-water emulsions

Algae oil-in-water emulsions stabilized with 0.2% whey protein isolate (WPI) at pH 3.0 and 7.0 were chosen to evaluate antioxidant activity of a proanthocyanidin-rich extract from grape seed. In this emulsion system, (+)-catechin and ascorbic acid (620 microM) were found to be prooxidative at pH 3.0 and ineffective at pH 7.0. Grape seed extract was not able to effectively inhibit both lipid hydroperoxides and propanal formation when added to the emulsion at 124 microM. However, increasing the concentration of the grape seed extract to 620 microM resulted in inhibition of both lipid hydroperoxide and propanal formation at pH 3.0 and 7.0. None of the antioxidants tested had any effect on the physical stability of the WPI-stabilized emulsion. The superior antioxidant activity of the grape seed extract is likely due to the presence of oligomeric procyanidins which are better antioxidants compared to their monomeric counterparts.     

Increasing the oxidative stability of liquid and dried tuna oil-in-water emulsions with electrostatic layer-by-layer deposition technology

Omega-3 Fatty acids have numerous health benefits, but their addition to foods is limited by oxidative rancidity. Engineering the interfacial membrane of oil-in-water emulsion droplets to produce a cationic and/or thick interface is an effective method to control lipid oxidation. Cationic and thick emulsion droplet interfacial membranes can be produced by an electrostatic layer-by-layer deposition technique resulting in droplets that are coated by multiple layers of emulsifiers. Tuna oil-in-water emulsion droplets coated by lecithin and chitosan produce cationic emulsion droplets that are more oxidatively stable than emulsions coated by lecithin alone. Ethylenediaminetetraacetic acid (EDTA) was able to increase the oxidative stability of emulsions stabilized with lecithin and chitosan more effectively than mixed tocopherols. The combination of EDTA and mixed tocopherols was not more effective than EDTA alone suggesting that control of prooxidant metals was the most important antioxidant technology. The production of emulsion droplets coated with lecithin and chitosan could be an excellent technology for stabilization of oxidatively unstable lipids for use in a variety of food products.     

Color changes in hydrocarbon oil-in-water emulsions caused by Ostwald ripening

The influence of Ostwald ripening on the optical properties of hydrocarbon oil-in-water emulsions stabilized by sodium dodecyl sulfate was investigated. The droplet size, spectral reflectance, and tristimulus color coordinates (L, a, and b) of a series of n-hexadecane and n-octadecane oil-in-water emulsions were measured in the presence and absence of a water-soluble red dye (FD&C Red No. 40). The droplets grew more rapidly in the emulsion containing n-hexadecane than in the emulsion containing n-octadecane because of the higher solubility of n-hexadecane molecules in the aqueous phase. Ostwald ripening caused appreciable changes in n-hexadecane emulsion spectral reflectance and color L, a, and b values due to the growth of emulsion droplets. L, a, and b color values and spectral reflectances of n-octadecane emulsions did not significantly change during the course of the experiment. The results were explained in terms of Ostwald ripening theory and a previously described light scattering theory. The model enables emulsion manufacturers to predict color changes in oil-in-water emulsions that exhibit transcondensational ripening.     

Chemical and physical stability of citral and limonene in sodium dodecyl sulfate-chitosan and gum arabic-stabilized oil-in-water emulsions

Citral and limonene are the major flavor components of citrus oils. Both of these compounds can undergo chemical degradation leading to loss of flavor and the formation of undesirable off-flavors. Engineering the interface of emulsion droplets with emulsifiers that inhibit chemical reactions could provide a novel technique to stabilize citral and limonene. At present, emulsified flavor oils are usually stabilized by gum arabic (GA), which is a naturally occurring polysaccharide-protein complex. The objective of this study was to examine if citral and limonene were more stable in emulsions stabilized with a sodium dodecyl sulfate (SDS)-chitosan complex than GA. Citral degraded less in GA-stabilized than in SDS-chitosan-stabilized emulsions at pH 3.0. However, SDS-chitosan-stabilized emulsions were more effective at retarding the formation of the citral oxidation product, p-cymene, than GA-stabilized emulsions. Limonene degradation and the formation of limonene oxidation products, limonene oxide and carvone, were lower in the SDS-chitosan- than GA-stabilized emulsions at pH 3.0. The ability of an SDS-chitosan multilayer emulsifier system to inhibit the oxidative deterioration of citral and limonene could be due to the formation of a cationic and thick emulsion droplet interface that could repel prooxidative metals, thus decreasing prooxidant-lipid interactions.     

Infrared study of structural characteristics of Frankfurters formulated with olive oil-in-water emulsions stabilized with casein as pork backfat replacer

This article reports an infrared spectroscopic (FT-IR) study on lipids and protein structural characteristics in frankfurters as affected by an emulsified olive oil stabilizing system used as a pork backfat replacer. The oil-in-water emulsions were stabilized with sodium caseinate, without (F/SC) and with microbial transglutaminase (F/SC+MTG). Proximate composition and textural characteristics were also evaluated. Frankfurters F/SC+MTG showed the highest (P < 0.05) hardness and lowest (P < 0.05) adhesiveness. These products also showed the lowest (P < 0.05) half-bandwidth of the 2922 cm(-1) band, which could be related to the fact that the lipid chain was more orderly than that in the frankfurters formulated with animal fat and F/SC. The spectral results revealed modifications in the amide I band profile when the olive oil-in-water emulsion replaced animal fat. This fact is indicative of a greater content of aggregated intermolecular β-sheets. Structural characteristics in both proteins and lipids could be associated with the specific textural properties of frankfurters.     

Addition of sugars influences color of oil-in-water emulsions

The influence of glucose, fructose, lactose, and glycerol on the color and appearance of surfactant-stabilized oil-in-water emulsions containing a red dye was investigated. A stabilized (Tween-20) oil-in-water emulsion was diluted into sugar solutions to give a range of oil droplet and sugar concentrations. Tristimulus coordinates (L, a, b) and reflectance spectra were measured using a spectrophotometer. With increasing sugar concentration, reflectance spectra shifted to lower reflectance values. Tristimulus coordinates were reduced by approximately 50% for emulsions containing high concentrations of sugar. Adding fructose to emulsions reduced L, a, b values more significantly than adding glucose, lactose, or glycerol. Tristimulus coordinates remained constant when the temperature was raised from 20 to 80 degrees C. The experimental results were explained in terms of the change of relative refractive index at the water-oil interface. The results have important implications for the food industry as they offer a new means to control and optimize the color of food emulsions.     

Oxidative stability of fish and algae oils containing long-chain polyunsaturated fatty acids in bulk and in oil-in-water emulsions

The oxidative stability of long-chain polyunsaturated fatty acid (PUFA) and docosahexaenoic acid (DHA)-containing fish and algae oils varies widely according to their fatty acid composition, the physical and colloidal states of the lipids, the contents of tocopherols and other antioxidants, and the presence and activity of transition metals. Fish and algal oils were initially much more stable to oxidation in bulk systems than in the corresponding oil-in-water emulsions. The oxidative stability of emulsions cannot, therefore, be predicted on the basis of stability data obtained with bulk long-chain PUFA-containing fish oils and DHA-containing algal oils. The relatively high oxidative stability of an algal oil containing 42% DHA was completely lost after chromatographic purification to remove tocopherols and other antioxidants. Therefore, this evidence does not support the claim that DHA-rich oils from algae are unusually stable to oxidation. Addition of ethylenediaminetetraacetic acid (EDTA) prevented oxidation of both fish and algal oil emulsions without added iron and at low iron:EDTA molar concentrations. EDTA, however, promoted the oxidation of the corresponding emulsions that contained high iron:EDTA ratios. Therefore, to be effective as a metal chelator, EDTA must be added at molar concentrations higher than that of iron to inhibit oxidation of foods containing long-chain PUFA from either fish or algae and fortified with iron.     

Interactions of whey proteins during heat treatment of oil-in-water emulsions formed with whey protein isolate and hydroxylated lecithin

The interactions of proteins during the heat treatment of whey-protein-isolate (WPI)-based oil-in-water emulsions with and without added hydroxylated lecithin were studied by examining the changes in droplet size distribution and the quantity and type of adsorbed and unadsorbed proteins. Heat treatment at 90 degrees C of WPI emulsions resulted in an increase in total adsorbed protein; unadsorbed beta-lactoglobulin (beta-lg) was the main protein interacting with the adsorbed proteins during the first 10 min of heating, but after this time, unadsorbed alpha-lactalbumin (alpha-la) also associated with the adsorbed protein. In emulsions containing hydroxylated lecithin, the increase in total adsorbed protein during heat treatment was much lower and the unadsorbed beta-lg did not appear to interact with the adsorbed proteins during heating. However, the behavior of alpha-la during heat treatment of these emulsions was similar to that observed in the emulsions containing no hydroxylated lecithin. In the presence of NaCl, the particle size of the emulsion droplets and the quantities of adsorbed protein increased markedly during heating. Emulsions containing hydroxylated lecithin were less sensitive to the addition of NaCl. These results suggest that the binding of hydroxylated lecithin to unfolded monomers or intermediate products of beta-lg reduces the extent of heat-induced aggregation of beta-lg and consequently decreases the interactions between unadsorbed beta-lg and adsorbed protein. This was confirmed by sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) of heated whey protein and hydroxylated lecithin solutions.