Model studies on the stability of folic acid and 5-methyltetrahydrofolic acid degradation during thermal treatment in combination with high hydrostatic pressure

Stability of folic acid and 5-methyltetrahydrofolic acid in phosphate buffer (0.2 M; pH 7) toward thermal (above 65 degrees C) and combined high pressure (up to 800 MPa)/thermal (20 up to 65 degrees C) treatments was studied on a kinetic basis. Residual folate concentration after thermal and high pressure/thermal treatments was measured using reverse phase liquid chromatography. The degradation of both folates followed first-order reaction kinetics. At ambient pressure, the estimated Arrhenius activation energy (E(a)) values of folic acid and 5-methyltetrahydrofolic acid thermal degradation were 51.66 and 79.98 kJ mol(-1), respectively. It was noticed that the stability of folic acid toward thermal and combined high pressure thermal treatments was much higher than 5-methyltetrahydrofolic acid. High-pressure treatments at room temperature or higher (up to 60 degrees C) had no or little effect on folic acid. In the whole P/T area studied, the rate constant of 5-methyltetrahydrofolic acid degradation was enhanced by increasing pressure, and a remarkable synergistic effect of pressure and temperature on 5-methyltetrahydrofolic acid degradation occurred at temperatures above 40 degrees C. A model to describe the combined pressure and temperature effect on the 5-methyltetrahydrofolic acid degradation rate constant is presented.     

Thermal degradation of anthocyanins from purple potato (cv. Purple Majesty) and impact on antioxidant capacity

Degradation parameters of purified anthocyanins from purple-fleshed potato (cv. Purple Majesty) heated at high temperatures (100-150 °C) were determined. Purified anthocyanins, prepared by removing salts, sugars, and colorless nonanthocyanin phenolics from the crude extract, were monitored and quantified using HPLC and spectrophotometry for heat-induced degradation products. Separation of colorless phenolics from the anthocyanins was confirmed using HPLC at two wavelengths, 280 and 520 nm. The degradation kinetics of purified anthocyanins followed a first-order reaction with reaction rate constants (k values) of 0.0262-0.2855 min(-1), an activation energy of 72.89 kJ/mol, thermal death times (D values) of 8.06-8789 min, and a z value of 47.84 °C over the temperature range of 100-150 °C. The enthalpy and entropy of activation were 59.97 kJ/mol and -116.46 J/mol·K, respectively. The antioxidant capacity in the purified anthocyanins, measured by DPPH and ABTS assays, was increased after the thermal treatment, indicating antioxidant activities of degradation products in the samples.     

Effect of temperature and moisture on the degradation and sorption of florasulam and 5-hydroxyflorasulam in soil

The degradation rate and sorption characteristics of the triazolopyrimidine sulfonanilide herbicide florasulam and its principal degradation product 5-hydroxyflorasulam (5-OH-florasulam) were determined as a function of temperature and moisture in three different soils. The half-life for degradation of florasulam ranged from 1.0 to 8.5 days at 20-25 degrees C and from 6.4 to 85 days at 5 degrees C. The half-life for degradation of 5-OH-florasulam ranged from 8 to 36 days at 20-25 degrees C and from 43 to 78 days at 5 degrees C. The degradation rate of both compounds was strongly influenced by temperature, with activation energies ranging from 57 to 95 kJ/mol for florasulam and from 27 to 74 kJ/mol for 5-OH florasulam. Soil moisture content had negligible impact on the degradation rate. Apparent (nonequilibrium) sorption coefficients for florasulam and 5-OH-florasulam at 0 days after treatment (DAT) were 0.1-0.6 L/kg and increased linearly with time for both florasulam and 5-OH-florasulam (r(2) > 0.90) to levels as high as 12-23 L/kg. Heats of adsorption were calculated on one soil as a function of time. Heat of adsorption values for both florasulam and 5-OH-florasulam increased as incubation time increased and the amount of each compound decreased; values were near 0 kJ/mol initially and increased to a maximum of 91 and 66 kJ/mol for florasulam and 5-OH-florasulam, respectively.     

Kinetics of the stability of broccoli (Brassica oleracea Cv. Italica) myrosinase and isothiocyanates in broccoli juice during pressure/temperature treatments

The Brassicaceae plant family contains high concentrations of glucosinolates, which can be hydrolyzed by myrosinase yielding products having an anticarcinogenic activity. The pressure and temperature stabilities of endogenous broccoli myrosinase, as well as of the synthetic isothiocyanates sulforaphane and phenylethyl isothiocyanate, were studied in broccoli juice on a kinetic basis. At atmospheric pressure, kinetics of thermal (45-60 degrees C) myrosinase inactivation could be described by a consecutive step model. In contrast, only one phase of myrosinase inactivation was observed at elevated pressure (100-600 MPa) combined with temperatures from 10 up to 60 degrees C, indicating inactivation according to first-order kinetics. An antagonistic effect of pressure (up to 200 MPa) on thermal inactivation (50 degrees C and above) of myrosinase was observed indicating that pressure retarded the thermal inactivation. The kinetic parameters of myrosinase inactivation were described as inactivation rate constants (k values), activation energy (Ea values), and activation volume (Va values). On the basis of the kinetic data, a mathematical model describing the pressure and temperature dependence of myrosinase inactivation rate constants was constructed. The stability of isothiocyanates was studied at atmospheric pressure in the temperature range from 60 to 90 degrees C and at elevated pressures in the combined pressure-temperature range from 600 to 800 MPa and from 30 to 60 degrees C. It was found that isothiocyanates were relatively thermolabile and pressure stable. The kinetics of HP/T isothiocyanate degradation could be adequately described by a first-order kinetic model. The obtained kinetic information can be used for process evaluation and optimization to increase the health effect of Brassicaceae.     

Thermal and high-pressure inactivation kinetics of polyphenol oxidase in Victoria grape must

The inactivation kinetics of polyphenol oxidase (PPO) in freshly prepared grape must under high hydrostatic pressure (100-800 MPa) combined with moderate temperature (20-70 degrees C) was investigated. Atmospheric pressure conditions in a temperature range of 55-70 degrees C were also tested. Isothermal inactivation of PPO in grape must could be described by a biphasic model. The values of activation energy and activation volume of stable fraction were estimated as 53.34 kJ mol(-1) and -18.15 cm3 mol(-1) at a reference pressure of 600 MPa and reference temperature of 50 degrees C, respectively. Pressure and temperature were found to act synergistically, except in the high-temperature-low-pressure region where an antagonistic effect was found. A third-degree polynomial model was successfully applied to describe the temperature/pressure dependence of the inactivation rate constants of the stable PPO fraction in grape must.     

Inactivation of apple pectin methylesterase induced by dense phase carbon dioxide

The inactivation of apple pectin methylesterase (PME) with dense phase carbon dioxide (DPCD) combined with temperatures (35-55 degrees C) is investigated. DPCD increases the susceptibility of apple PME to the temperatures and the pressures have a noticeable effect on apple PME activity. A labile and stable fraction of apple PME is present and the inactivation kinetics of apple PME by DPCD is adequately described by a two-fraction model. The kinetic rate constants k L and k S of labile and stable fractions are 0.890 and 0.039 min (-1), and the decimal reduction times D L and D S are 2.59 and 58.70 min at 30 MPa and 55 degrees C. Z T representing temperature increase needed for a 90% reduction of the D value and the activation energy E a of the labile fraction at 30 MPa is 22.32 degrees C and 86.88 kJ /mol, its Z P representing pressure increase needed for a 90% reduction of the D value and the activation volume V a at 55 degrees C is 21.75 MPa and -288.38 cm (3)/mol. The residual activity of apple PME after DPCD exhibits no reduction or reactivation for 4 weeks at 4 degrees C.     

Physical stability of shikonin derivatives from the roots of Lithospermum erythrorhizon cultivated in Korea.

Five red shikonin pigments, deoxyshikonin, shikonin, acetylshikonin, isobutylshikonin, and beta-hydroxyisovalerylshikonin, were isolated from the roots of Lithospermum erythrorhizon cultivated in Korea. The purified pigments were red, purple, and blue at acidic, neutral, and alkaline pH values, respectively. Physical stability of the purified pigments against heat and light in an aqueous solution was examined for possible value-added food colorants. The thermal degradation reactions were carried out at pH 3.0 (50 mM glycine buffer) in 50% EtOH/H(2)O. Deoxyshikonin (t(1/2) = 14.6 h, 60 degrees C) and isobutylshikinin (t(1/2) = 19.3 h, 60 degrees C) are relatively less stable than other shikonin derivatives (t(1/2) = 40-50 h, 60 degrees C). Activation energies of thermal degradation of the isolated pigments were calculated. The activation energy of deoxyshikonin was the highest (12.5 kcal mol(-)(1)) and that of beta-hydroxyisovalerylshikonin was the lowest (1.71 kcal mol(-)(1)) value. Light stabilities of the pigments were similar to each other in that the half-life values of photodegradation for 20000 lx light intensity were 4.2-5.1 h.     

Pressure and temperature stability of 5-methyltetrahydrofolic acid: a kinetic study

Detailed kinetic studies of [6S] and [6RS] 5-methyltetrahydrofolic acid (5-CH3-H4folate) degradation during thermal (from 60 to 90 degrees C) and high pressure/thermal (from 30 to 45 degrees C; from 200 to 700 MPa) treatments were carried out. The results confirmed that the temperature and pressure induced degradation kinetics of [6S] 5-CH3-H4folate were identical (within 95% confidence interval) with those of [6RS] 5-CH3-H4folate. Under equal processing conditions, the estimated degradation rate constants (k), activation energy (E(a)), and activation volume (V(a)) values of [6S] and [6RS] 5-CH3-H4folate were the same (95% confidence interval). The modified thermodynamic model proposed by Nguyen and co-workers (J. Agric. Food Chem. 2003, 51, 3352-3357) to describe the pressure and temperature dependence of the rate constant for folate degradation was reevaluated.     

Effects of succinylation on the structure and thermostability of lysozyme

The influence of succinylation on lysozyme is studied using circular dichroism, fluorescence spectroscopy, and differential scanning calorimetry. The spectroscopic data reveal that at room temperature the structures of succinylated lysozyme and native lysozyme are similar. However, the calorimetric results show that the thermal stability of succinylated lysozyme is lower than that of native lysozyme. For succinylated lysozyme, the denaturation temperature (Td) varies in the range of 325-333 K (52-60 degrees C) and the associated denaturation enthalpy (DeltadenH) varies between 225 and 410 kJ/mol. For lysozyme, Td is 342-349 K (69-76 degrees C) and DeltadenH is 440-500 kJ/mol. From these data, the change in the heat capacity (DeltadenCp) upon thermal denaturation is derived. For lysozyme, DeltadenCp is 7.5 kJ/mol/K, and for succinylated lysozyme, it is 16.7 kJ/mol/K. The value of DeltadenCp for lysozyme is comparable to previously reported values. The high value of DeltadenCp for succinylated lysozyme is explained in terms of an extended degree of unfolding of the secondary structure and exposure of the apolar parts of the succinyl groups. Furthermore, the Gibbs energy of denaturation, as a function of temperature, derived from the thermodynamic analysis of the calorimetric data, indicates a cold-denaturated state of succinylated lysozyme below 20 degrees C. However, because a denatured state at low temperatures could not be detected by CD or fluorescence measurements, the native state may be considered to be metastable at those conditions.     

Kinetic study of the thermal stability of tea catechins in aqueous systems using a microwave reactor

Tea catechins may undergo complex reactions such as oxidation, polymerization, and epimerization during thermal processing. The thermal stability of tea catechins in an aqueous system, including degradation and epimerization reactions, was investigated using a microwave reactor. Reactions were controlled at high temperatures ranging from 100 to 165 degrees C with various durations up to 120 min. Three sources of tea catechins containing different levels of (-)-epigallocatechin gallate (EGCG), (-)-epicatechin gallate (ECG), and their epimers were studied. Kinetic models for the degradation/epimerization of tea catechins were developed and validated by the reactions at 145 degrees C. It was shown that the epimerization and degradation of tea catechins followed first-order reactions and the rate constants of reaction kinetics followed the Arrhenius equation. Values of the activation energy (E(a)) for the epimerization of EGCG from epi- to nonepi-structures, the epimerization of GCG from nonepi- to epi-structures, and the total degradation of EGCG and its epimer GCG were 117.6, 84.2, and 42.8 kJ/mol, respectively. For ECG and CG, the E(a) values were 119.3, 96.2, and 41.6 kJ/mol, respectively. The mathematical models may provide a useful prediction for the loss of tea catechins during any thermal processing.     

Color properties and stability of betacyanins from Opuntia fruits

The colorant properties of pigments from Opuntia stricta, Opuntia undulata, and Opuntia ficus-indicafruits were studied. The pigments were extracted with different solvents and identified by high-performance liquid chromatography. On the basis of their visible light spectra, the pigments were identified as betalains. In O. undulata and O. ficus-indica fruits, both betacyanins and betaxantins were identified, while in O. stricta fruits only betacyanins (betanin and isobetanin) were detected. O. stricta fruits showed the highest betacyanin content (80 mg/100 g fresh fruit). The thermal stability of the pigment extracts was dependent on the pH, with the maximum stability being at pH 5, as expected for betacyanins. At this value and a storage temperature of 4 degrees C, a deactivation half-life time of more than 1 year, with no added stabilizers, was determined. According to these studies, cactus pears from O. stricta may well be considered as a potential source of natural red colorants.     

Characterization and role of polyphenol oxidase and peroxidase in browning of fresh-cut melon

Polyphenol oxidase (PPO) and peroxidase (POD) were extracted from two different varieties of melon ( Cucumis melo L. cantalupensis cv. Charentais and C. melo L. inodorus cv. Amarillo) and characterized using reliable spectrophotometric methods. In both cases the enzymes followed Michaelis-Menten kinetics, showing different values of kinetics parameters between the two cultivars: K m = 7.18 +/- 0.70 mM ('Charentais') and 6.66 +/- 0.20 mM ('Amarillo') mM; V max = 7.93 +/- 0.35 units/min ('Charentais') and 13.82 +/- 0.37 units/min ('Amarillo'), relative to PPO; K m = 24.0 +/- 2.10 mM ('Charentais') and 5.05 +/- 0.19 mM ('Amarillo') mM; V max = 344.83 +/- 10.32 units/min ('Charentais') and 80.64 +/- 2.01 units/min ('Amarillo'), relative to POD. Optimum pH for PPO was 7.0 for 'Charentais' and 7.5 for 'Amarillo, whereas it was 4.5 for both cultivars relative to POD. Melon PPO had maximum activity at 60 degrees C in both 'Charentais' and 'Amarillo' cultivars, whereas POD maximum activity was found at 45 degrees C in 'Charentais' and at 25 degrees C in 'Amarillo'. POD from both cultivars showed higher thermolability compared with PPO, losing >90% of relative activity after only 5 min of incubation at 70 degrees C. POD's activation energy was much higher than that of PPO (Delta E (#) = 86.3 and 160.6 kJ mol (-1) for 'Charentais' and 'Amarillo', respectively). PPO and POD activities from both cultivars showed a decreasing pattern as sugar concentration in the assay medium increased, except in POD extract from 'Charentais', which maintained its activity in the presence of high d-glucose concentration (up to 5 M). Changes in L*, a*, b*, chroma, and hue angle values were chosen to describe the browning development in the samples during storage at 5 degrees C. A slight decrease in L* value and a more marked reduction of a* value were noted in both cultivars above all at the end of storage period. POD activity during storage at 5 degrees C was highly correlated with changes of parameters a*, b*, chroma, and hue angle ( r (2) from 0.82 to 0.97) for cultivar 'Charentais'. According to these results, only POD activity seemed to be involved in browning of minimally processed melon.     

杀菌方式对石榴浊汁微生物和色泽的影响

为探讨不同杀菌方式对石榴浊汁在4℃冷藏期间微生物和色泽品质的影响,本研究采用超高压技术(HPP,450 MPa/1 min、450 MPa/5 min、550 MPa/1 min、550 MPa/5 min)、巴氏杀菌技术(PT,85℃/30 s)和高温短时杀菌技术(HTST,110℃/8.6 s)对石榴浊汁进行杀菌处理,并重点研究了抗坏血酸和色泽参数变化的动力学特征。结果表明,冷藏期间,HPP和HTST处理石榴浊汁微生物在标准范围内。HPP处理能较好地保留石榴浊汁中脱氢抗坏血酸(DHAA)的含量,而PT和HTST处理后DHAA含量较未处理样品(第0天)分别降低了21%和35%;冷藏期间不同杀菌方式处理后DHAA含量均呈下降趋势;经一级动力学模型拟合发现,HPP处理组DHAA的降解速率常数k值高于PT和HTST处理组。与热处理(PT和HTST)相比,冷藏前期,HPP处理能保持石榴浊汁较高的L^*、a^*、b^*值和较低的ΔE值,保持较优的色泽品质;采用一级分数转换动力学模型对L^*、a^*和ΔE值进行拟合,发现HPP处理样品色泽参数在冷藏过程中的k值同样高于热处理样品,即随着冷藏时间的延长,HPP处理组色泽品质逐渐降低。综上所述,HPP处理能在保证石榴浊汁冷藏期间微生物安全的同时,较好地保持其色泽品质。本研究为石榴浊汁工业化生产中杀菌方式的选择提供了理论依据。     

Use of differential scanning calorimetry to study lipid oxidation. 1. Oxidative stability of lecithin and linolenic acid

The oxidation of linolenic acid (LNA) and soy lecithin was studied by differential scanning calorimetry (DSC) with linear programmed heating rates (non-isothermal mode). The interpretation of the shape of DSC curves is discussed, and it has been concluded that temperatures of the extrapolated start of heat release are the most reliable data for the rapid estimation of the oxidative stability of lipid materials. The Ozawa-Flynn-Wall method was used to calculate the kinetic parameters of the process: for LNA autoxidation the activation energy, Ea, and pre-exponential factor, Z, are 66 +/- 4 kJ/mol and 1.5 x 10(7) s(-1), respectively, and the autoxidation of lecithin is described by Ea = 98 +/- 6 kJ/mol and Z = 9.1 x 10(10) s(-1). Values of Ea and Z can be applied for calculation of the overall first-order rate constant of autoxidation at various temperatures, k(T). For the two studied lipids the comparison of k(T) values shows the inversion of their oxidative stabilities; that is, below 167 degrees C lecithin is more stable than LNA, k(T)lecithin < k(T)LNA, and above that temperature (termed the isokinetic temperature) k(T)lecithin > k(T)LNA. The calculated inversion of oxidative stabilities can be an explanation of similar observations for other pairs of lipids if the results of accelerated tests measured at temperatures above 100 degrees C are compared with the results obtained at temperatures below 100 degrees C.     

Unfolding and refolding of beta-lactoglobulin subjected to high hydrostatic pressure at different pH values and temperatures and its influence on proteolysis

The unfolding of beta-lactoglobulin during high-pressure treatment and its refolding after decompression were studied by 1H NMR and 2H/1H exchange at pH 6.8 and 2.5 and at 37 and 25 degrees C. The extent of unfolding increased with the pressure level. The structure of beta-lactoglobulin required higher pressures to unfold at pH 2.5 than at pH 6.8. More flexibility was achieved at 37 degrees C than at 25 degrees C. Results indicated that the structural region formed by strands F, G, and H was more resistant to unfold under acidic and neutral conditions. The exposure of Trp19 at an earlier time, as compared to other protein regions, supports the formation of a swollen structural state at pH 2.5. Refolding was achieved faster when beta-lactoglobulin was subjected to 200 MPa than to 400 MPa, to 37 degrees C than to 25 degrees C, and to acidic than to neutral pH. After treatment at 400 MPa for 20 min at neutral pH, the protein native structure was not recovered. All samples at acidic pH showed that the protein quickly regained its structure. Hydrolysis of beta-lactoglobulin by pepsin and chymotrypsin could be related to pressure-induced changes in the structure of the protein. Compared to the behavior of the protein at atmospheric pressure, no increased proteolysis was found in samples with no increased flexibility (100 MPa, 37 degrees C, pH 2.5). Slightly flexible structures were associated with significantly increased proteolysis (100 MPa, 37 degrees C, pH 6.8; 200 MPa, 37 degrees C, pH 2.5). Highly flexible structures were associated with very fast proteolysis (>or=200 MPa, 37 degrees C, pH 6.8; >or=300 MPa, 37 degrees C, pH 2.5). Proteolysis of prepressurized samples improved only when the protein was significantly changed after the pressure treatment (400 MPa, 25 degrees C, 20 min, pH 6.8).     

Inactivation of heat-resistant pectinmethylesterase from orange by manothermosonication

Pectinmethylesterase of navel oranges shows two fractions greatly differing in thermostability. The most thermostable fraction accounts for approximately 10% of total activity. The thermal inactivation of this fraction follows first-order kinetics both in 5 mM, pH 3.5, citrate buffer and in orange juice at the same pH, showing a z value of 5.1 degrees C and an activation energy (E(a)) of 435 kJ mol(-)(1) K(-)(1). The heat resistance of the enzyme is approximately 25-fold higher in the juice than in citrate buffer. When ascorbic acid, sucrose, glucose, and fructose are added to the citrate buffer at the concentrations found in orange juice, the heat resistance of the enzyme increases 3-fold. The addition of pectin at 0.01% concentration multiplies it by a factor of 50. Manothermosonication (MTS), the simultaneous application of heat and ultrasound under moderate pressure (200 kPa), at 72 degrees C, increases the inactivation rate 25 times in buffer and >400 times in orange juice. MTS inactivation shows a higher z value (35.7 degrees C) and lower E(a) (56.9 kJ mol(-)(1) K(-)(1)) than simple heating.     

Changes in sulfhydryl content of egg white proteins due to heat and pressure treatment

The sulfhydryl (SH) content of egg white proteins (10% v/v or 9.64 mg of protein/mL) after heat (50-85 degrees C) and combined heat- and high-pressure treatments (100-700 MPa, 10-60 degrees C) was determined using 5',5-dithiobis (2-nitrobenzoic acid) (DTNB), both for the soluble fraction and the total protein fraction. Only irreversible changes were taken into account. Both physical treatments were performed at two pH levels: pH 7.6, corresponding to the pH of fresh egg white, and pH 8.8, corresponding to that of aged egg white. Both heat and combined heat- and high-pressure treatment resulted in an exposure of buried SH groups. These exposed SH groups were involved in the formation of disulfide bond stabilized protein aggregates, as shown by gel electrophoresis. Under severe processing conditions (above 70 degrees C at atmospheric pressure or above 500-600 MPa, depending on the temperature applied), a decrease in total SH content could be observed, probably due to the formation of disulfide bonds by oxidation, especially at alkaline pH when the thiolate anion was more reactive. The high degree of exposure of sulfhydryl groups, and subsequent oxidation and sulfhydryl-disulfide bond exchange reactions resulting in soluble aggregates, can explain why pressure-induced egg white gels are softer and more elastic than heat-induced ones. When pressure treatment was performed at low temperatures (e.g., 10 degrees C), a lower pressure was required to induce similar changes in the sulfhydryl content, as compared to higher temperatures (e.g., 25 degrees C), indicating an antagonistic effect between pressure and temperature in the domain studied (10-60 degrees C, 100-700 MPa). Treatment conditions resulting in extensive protein insolubilization were accompanied by a transfer of free sulfhydryl groups from the soluble to the insoluble protein fraction. These SH groups were mainly accessible to DTNB.     

Tomato (Lycopersicon esculentum) pectin methylesterase and polygalacturonase behaviors regarding heat- and pressure-induced inactivation.

The combined high pressure/thermal (HP/T) inactivation of tomato pectin methyl esterase (PME) and polygalacturonase (PG) was investigated as a possible alternative to thermal processing classically used for enzyme inactivation. The temperature and pressure ranges tested were from 60 degrees C to 105 degrees C, and from 0.1 to 800 MPa, respectively. PME, a heat-labile enzyme at ambient pressure, is dramatically stabilized against thermal denaturation at pressures above atmospheric and up to 500-600 MPa. PG, however, is very resistant to thermal denaturation at 0.1 MPa, but quickly and easily inactivated by combinations of moderate temperatures and pressures. Selective inactivation of either PME or PG was achieved by choosing proper combinations of P and T. The inactivation kinetics of these enzymes was measured and described mathematically over the investigated portion of the P/T plane. Whereas medium composition and salinity had little influence on the inactivation rates, PME was found less sensitive to both heat and pressure when pH was raised above its physiological value. PG, on the other hand, became more labile at higher pH values. The results are discussed in terms of isoenzymes and other physicochemical features of PME and PG.     

Kinetics of freshly squeezed orange juice quality changes during ozone processing

Freshly squeezed orange juice samples were ozonated with control variables of gas flow rate (0-0.25 L min (-1)), ozone concentration (0.6-10.0%w/w), and treatment time (0-10 min). Effects of ozone processing variables on orange juice quality parameters of pH, degrees Brix, titratable acidity (TA), cloud value, nonenzymatic browning (NEB), color values ( L*, a*, and b*), and ascorbic acid content were determined. No significant changes in pH, degrees Brix, TA, cloud value, and NEB ( p < 0.05) were found. L*, a*, and b* color values were significantly affected by gas flow rate, ozone concentration, and treatment time. The changes in lightness ( L*) values and total color difference (TCD) values were fitted well to zero-order kinetics, whereas a*, b*, and ascorbic acid degradation followed first-order kinetics. The rate constants for a*, b*, and TCD were linearly correlated with ozone concentration ( R (2) = 0.88-0.99), whereas the rate constants for L* and ascorbic acid were exponentially correlated ( R (2) = 0.94-0.98).     

Kinetics of chlorophyll degradation and color loss in heated broccoli juice

Degradation of chlorophyll in broccoli juice occurred at temperatures exceeding 60 degrees C. Chemical analysis revealed that degradation of chlorophyll a and b to pheophytin a and b, respectively, followed first-order kinetics and that chlorophyll a was more heat sensitive than chlorophyll b. Temperature dependencies of chlorophyll a and b degradation rate constants could be described by Arrhenius equations with activation energies (E(a)) of 71.04 +/- 4.89 and 67.11 +/- 6.82 kJ/mol, respectively. Objective greenness measurements, using the -a value as the physical property, together with a fractional conversion kinetic analysis, indicated that green color degradation followed a two-step process. Kinetic parameters for the first degradation step were in accordance with the kinetic parameters for pheophytinization of the total chlorophyll content, as determined by chemical analysis (E(a) approximately 69 kJ/mol). The second degradation step, that is, the subsequent decomposition of pheophytins, was characterized by an activation energy of 105.49 +/- 4.74 kJ/mol.