Homogenization conditions affect the oxidative stability of fish oil enriched milk emulsions: lipid oxidation

In this study fish oil was incorporated into commercial homogenized milk using different homogenization temperatures and pressures. The main aim was to understand the significance of homogenization temperature and pressure on the oxidative stability of the resulting milks. Increasing homogenization temperature from 50 to 72 degrees C decreased droplet size only slightly, whereas a pressure increase from 5 to 22.5 MPa decreased droplet size significantly. Surprisingly, emulsions having small droplets, and therefore large interfacial area, were less oxidized than emulsions having bigger droplets. Emulsions with similar droplet size distributions, but resulting from different homogenization conditions, had significantly different oxidative stabilities, indicating that properties of significance to oxidation other than droplet size itself were affected by the different treatments. In general, homogenization at 72 degrees C appeared to induce protective effects against oxidation as compared to homogenization at 50 degrees C. The results thus indicated that the actual composition of the oil-water interface is more important than total surface area itself.     

Role of continuous phase protein on the oxidative stability of fish oil-in-water emulsions

Whey protein isolate (WPI), soy protein isolate (SPI), and sodium caseinate (CAS) can inhibit lipid oxidation when they produce a positive charge at the interface of emulsion droplets. However, when proteins are used to stabilize oil-in-water emulsions, only a fraction of them actually absorb to the emulsion droplets, with the rest remaining in the continuous phase. The impact of these continuous phase proteins on the oxidative stability of protein-stabilized emulsions is not well understood. WPI-stabilized menhaden oil-in-water emulsions were prepared by high-pressure homogenization. In some experiments WPI was removed from the continuous phase of the emulsions through repeated centrifugation and resuspension of the emulsion droplets (washed emulsion). Unwashed emulsions were more oxidatively stable than washed emulsions at pH 7.0, suggesting that continuous phase proteins were antioxidative. The oxidative stability of emulsions containing different kinds of protein in the continuous phase decreased in the order SPI > CAS > WPI, as determined by both hydroperoxide and headspace propanal formation. Iron-binding studies showed that the chelating ability of the proteins decreased in the order CAS > SPI > WPI. The free sulfhydryls of both WPI and SPI were involved in their antioxidant activity. This research shows that continuous phase proteins could be an effective means of protecting omega-3 fatty acids from oxidative deterioration.     

Lipid oxidation in milk, yoghurt, and salad dressing enriched with neat fish oil or pre-emulsified fish oil

This study compared the oxidative stabilities of fish-oil-enriched milk, yoghurt, and salad dressing and investigated the effects on oxidation of adding either neat fish oil or a fish-oil-in-water emulsion to these products. Milk emulsions had higher levels of a fishy off-flavor and oxidized faster, as determined by the peroxide value and volatile oxidation products, than fish-oil-enriched yoghurt and dressing, despite the fact that dressings had a higher fish oil content and were stored at room temperature. Additionally, fish-oil-enriched yoghurt generally had higher oxidative stability than fish-oil-enriched dressings, irrespective of the mode of fish oil addition. Yoghurt thus seemed to be a good delivery system of lipids containing n-3 polyunsaturated fatty acids. Different effects of adding fish oil either as neat fish oil or as a fish-oil-in-water emulsion were observed for milk, yoghurt, and dressing. Yoghurt and dressing enriched with neat fish oil were more stable than those enriched with a fish-oil-in-water emulsion, whereas milk enriched with neat fish oil was less stable than milk enriched with the fish-oil-in-water emulsion. Overall, it seemed that application of neat fish oil was a good option for preserving the final quality in yoghurt and dressings, but a pre-emulsion may still be considered for the fish oil enrichment of certain food products, for example, milk.     

Ascorbyl palmitate, gamma-tocopherol, and EDTA affect lipid oxidation in fish oil enriched salad dressing differently

The aim of the study was to investigate the ability of gamma-tocopherol, ethylenediaminetetraacetate (EDTA), and ascorbyl palmitate to protect fish oil enriched salad dressing against oxidation during a 6 week storage period at room temperature. The lipid-soluble gamma-tocopherol (220 and 880 microg g-1 of fish oil) reduced lipid oxidation during storage by partly retarding the formation of lipid hydroperoxides (PV) and by decreasing the concentrations of individual volatile oxidation products by 34-39 and 42-66%, respectively. EDTA (10 and 50 microg g-1 of dressing) was the most efficient single antioxidant, and overall peroxide values and volatiles were reduced by approximately 70 and 77-86%, respectively. Conversely, prooxidant effects were observed with a high concentration of ascorbyl palmitate (300 microg g-1 of fish oil), whereas a low concentration was slightly antioxidative (50 microg/g of fish oil). Finally, a combination of all three antioxidants completely inhibited oxidation during storage, indicating that the prooxidant effects of ascorbyl palmitate were reverted or overshadowed by EDTA and gamma-tocopherol.     

Stabilization of model beverage cloud emulsions using protein-polysaccharide electrostatic complexes formed at the oil-water interface

The potential of utilizing interfacial complexes, formed through the electrostatic interactions of proteins and polysaccharides at oil-water interfaces, to stabilize model beverage cloud emulsions has been examined. These interfacial complexes were formed by mixing charged polysaccharides with oil-in-water emulsions containing oppositely charged protein-coated oil droplets. Model beverage emulsions were prepared that consisted of 0.1 wt % corn oil droplets coated by beta-lactoglobulin (beta-Lg), beta-Lg/alginate, beta-Lg/iota-carrageenan, or beta-Lg/gum arabic interfacial layers (pH 3 or 4). Stable emulsions were formed when the polysaccharide concentration was sufficient to saturate the protein-coated droplets. The emulsions were subjected to variations in pH (from 3 to 7), ionic strength (from 0 to 250 mM NaCl), and thermal processing (from 30 or 90 degrees C), and the influence on their stability was determined. The emulsions containing alginate and carrageenan had the best stability to ionic strength and thermal processing. This study shows that the controlled formation of protein-polysaccharide complexes at droplet surfaces may be used to produce stable beverage emulsions, which may have important implications for industrial applications.     

Adsorption of whey protein isolate at the oil-water interface as a function of processing conditions: a rheokinetic study

In this paper we present surface dynamic properties (interfacial tension and surface dilational properties) of a whey protein isolate with a high content of beta-lactoglobulin (WPI) adsorbed on the oil-water interface as a function of adsorption time. The experiments were performed at constant temperature (20 degrees C), pH (5), and ionic strength (0.05 M). The surface rheological parameters and the interfacial tension were measured as a function of WPI concentration (ranging from 1 x 10(-)(1) to 1 x 10(-)(5)% w/w) and different processing factors (effect of convection and heat treatment). We found that the interfacial pressure, pi, and surface dilational modulus, E, increase and the phase angle, phi, decreases with time, theta, which should be associated with WPI adsorption. These phenomena have been related to diffusion of the protein toward the interface (at short adsorption time) and to the protein unfolding and/or protein-protein interactions (at long-term adsorption) as a function of protein concentration in solution and processing conditions.     

Lipid oxidation in fish oil enriched mayonnaise: calcium disodium ethylenediaminetetraacetate, but not gallic acid, strongly inhibited oxidative deterioration

The antioxidative effects of gallic acid, EDTA, and extra emulsifier Panodan DATEM TR in mayonnaise enriched with 16% fish oil were investigated. EDTA reduced the formation of free radicals, lipid hydroperoxides, volatiles, and fishy and rancid off-flavors. The antioxidative effect of EDTA was attributed to its ability to chelate free metal ions and iron from egg yolk located at the oil-water interface. Gallic acid reduced the levels of both free radicals and lipid hydroperoxides but promoted slightly the oxidative flavor deterioration in mayonnaise and influenced the profile of volatiles. Gallic acid may therefore promote the decomposition of lipid hydroperoxides to volatile oxidation products. Addition of extra emulsifier reduced the lipid hydroperoxide levels but did not influence the level of free radicals or the oxidative flavor deterioration in mayonnaisse; however, it appeared to alter the profile of volatiles. The effect of the emulsifier on the physical structure and rheological properties depended on the presence of antioxidants.     

Effect of ascorbic acid on iron release from the emulsifier interface and on the oxidative flavor deterioration in fish oil enriched mayonnaise

This research examines the effect of ascorbic acid (0-800 ppm) on the sensory perception of mayonnaises containing 16% fish oil and on the levels of iron and copper in the aqueous phase. Ascorbic acid increased the formation of fishy off-flavors in fresh mayonnaise. Simultaneously, the iron concentration increased from below the detection limit (1.8 microM) to 34 microM in the aqueous phase of mayonnaises. Model mayonnaises with various concentrations of egg yolk (1-7% w/w) and ascorbic acid (0-8000 ppm) were prepared. Iron concentrations in the aqueous phase increased with increasing ascorbic acid levels, whereas iron concentrations in the assumed interfacial layer decreased. It is proposed that ascorbic acid is able to complex and reduce Fe(3+) to Fe(2+) from phosvitin in the egg yolk, whereby iron is released from the interface. The ascorbic acid-iron complex subsequently reacts with lipid hydroperoxides, resulting in increased lipid oxidation and in the immediate formation of rancid and fishy off-flavors.     

Oxidation in fish oil enriched mayonnaise: ascorbic acid and low pH increase oxidative deterioration

The effect of ascorbic acid (0-4000 ppm) and pH (3.8-6.2) on oxidation and levels of iron and copper in various fractions of mayonnaise enriched with 16% fish oil was investigated. Ascorbic acid induced release of iron from the assumed oil-water interface into the aqueous phase at all pH levels, but this effect of ascorbic acid was strongest at low pH (pH 3.8-4.2). Ascorbic acid generally promoted formation of volatile oxidation compounds and reduced the peroxide value in mayonnaises. Peroxide values and total volatiles generally increased with decreasing pH values, suggesting that low pH promoted oxidation. It is proposed that iron bridges between the egg yolk proteins low-density lipoproteins, lipovitellin, and phosvitin at the oil-water interface are broken at low pH values, whereby iron ions become accessible as oxidation initiators. In the presence of ascorbic acid, oxidation is further enhanced due to the reduction of Fe(3+) to Fe(2+) that rapidly catalyzes lipid oxidation via lipid hydroperoxide decomposition at the oil-water interface in mayonnaise.     

Adsorption and dilatational rheology of heat-treated soy protein at the oil-water interface: relationship to structural properties

We evaluated the influence of heat treatment on interfacial properties (adsorption at the oil-water interface and dilatational rheology of interfacial layers) of soy protein isolate. The related structural properties of protein affecting these interfacial behaviors, including protein unfolding and aggregation, surface hydrophobicity, and the state of sulfhydryl group, were also investigated. The structural and interfacial properties of soy protein depended strongly on heating temperature (90 and 120 °C). Heat treatment at 90 °C induced an increase in surface hydrophobicity due to partial unfolding of protein, accompanied by the formation of aggregates linked by disulfide bond, and lower surface pressure at long-term adsorption and similar dynamic interfacial rheology were observed as compared to native protein. Contrastingly, heat treatment at 120 °C led to a higher surface activity of the protein and rapid development of intermolecular interactions in the adsorbed layer, as evidenced by a faster increase of surface pressure and dilatational modulus. The interfacial behaviors of this heated protein may be mainly associated with more flexible conformation and high free sulfhydryl group, even if some exposed hydrophobic groups are involved in the formation of aggregates. These results would be useful to better understand the structure dependence of protein interfacial behaviors and to expand utilization of heat-treated protein in the formulation and production of emulsions.     

Impact of whey protein emulsifiers on the oxidative stability of salmon oil-in-water emulsions

To obtain a better understanding of how the interfacial region of emulsion droplets influences lipid oxidation, the oxidative stability of salmon oil-in-water emulsions stabilized by whey protein isolate (WPI), sweet whey (SW), beta-lactoglobulin (beta-Lg), or alpha-lactalbumin (alpha-La) was evaluated. Studies on the influence of pH on lipid oxidation in WPI-stabilized emulsions showed that formation of lipid hydroperoxides and headspace propanal was much lower at pH values below the protein's isoelectric point (pI), at which the emulsion droplets were positively charged, compared to that at pH values above the pI, at which the emulsion droplets were negatively charged. This effect was likely due to the ability of positively charged emulsion droplets to repel cationic iron. In a comparison of lipid oxidation rates of WPI-, SW-, beta-Lg-, and alpha-La-stabilized emulsions at pH 3, the oxidative stability was in the order of beta-Lg > or = SW > alpha-La > or = WPI. The result indicated that it was possible to engineer emulsions with greater oxidative stability by using proteins as emulsifier, thereby reducing or eliminating the need for exogenous food antioxidants.     

Chemical and olfactometric characterization of volatile flavor compounds in a fish oil enriched milk emulsion

Development of objectionable fishy off-flavors is an obstacle in the development of fish oil enriched foods. Only little is known about the sensory impact of specific volatile fish oil oxidation products in food emulsions. This study examined the volatiles profiles of fish oil enriched milk during cold storage (2 degrees C) for 14 days by dynamic headspace sampling followed by gas chromatography-mass spectrometry analyses. Different volatiles (n = 60) comprising alkenals, alkadienals, alkatrienals, and vinyl ketones were identified in the fish oil enriched milk. The potent odorants identified by gas chromatography-olfactometry were 1-penten-3-one, (Z)-4-heptenal, 1-octen-3-one, (Z)-1,5-octadien-3-one, (E,E)-2,4-heptadienal, and (E,Z)-2,6-nonadienal, but despite their potency, none of the separated volatiles imparted a fishy or metallic odor. Two isomers, (E,Z,Z) and (E,E,Z) of 2,4,7-decatrienal were identified in fish oil enriched milk emulsions with peroxide values 0.8 and 3.4 meq/kg, respectively. To our knowledge, this is the first report on appearance of these decatrienals in food emulsions having a relatively low peroxide value.     

Impact of extra virgin olive oil and ethylenediaminetetraacetic acid (EDTA) on the oxidative stability of fish oil emulsions and spray-dried microcapsules stabilized by sugar beet pectin

The influence of EDTA on lipid oxidation in sugar beet pectin-stabilized oil-in-water emulsions (pH 6, 15% oil, wet basis), prepared from fish oil (FO) and fish oil-extra virgin olive oil (FO-EVOO) (1:1 w/w), as well as the spray-dried microcapsules (50% oil, dry basis) prepared from these emulsions, was investigated. Under accelerated conditions (80 °C, 5 bar oxygen pressure) the oxidative stability was significantly (P < 0.05) higher for FO and FO-EVOO formulated with EDTA, in comparison to corresponding emulsions and spray-dried microcapsules formulated without EDTA. The EDTA effect was greater in emulsions than in spray-dried microcapsules, with the greatest protective effect obtained in FO-EVOO emulsions. EDTA enhanced the oxidative stability of the spray-dried microcapsules during ambient storage (~25 °C, a(w) = 0.5), as demonstrated by their lower concentration of headspace volatile oxidation products, propanal and hexanal. These results show that the addition of EDTA is an effective strategy to maximize the oxidative stability of both FO emulsions and spray-dried microcapsules in which sugar beet pectin is used as the encapsulant material.     

Impact of physicochemical characteristics on the oxidative stability of fish oil microencapsulated by spray-drying

The aim of the present research was to identify principal parameters determining the oxidative stability of microencapsulated fish oil. Microcapsules were prepared by spray-drying using different types of n-octenylsuccinate-derivatized starch, gum Arabic, sugar beet pectin, sodium caseinate, and/or glucose syrup. Two principal components to classify the different microcapsules accounting for up to 79% of the variance were identified. The principal components were determined by physicochemical parameters reflecting the emulsifying ability of the encapsulant and the drying behavior of the parent emulsion. Microcapsules, which were identified by principal component analysis to be significantly different, exhibited a low stability upon storage, showing that the principal components and, thus, the underlying physicochemical parameters analyzed in the present study are correlated with core material stability.     

Effect of relative humidity on oxidation of flaxseed oil in spray dried whey protein emulsions

Flaxseed oil was emulsified in whey protein isolate (WPI) and spray-dried. Powder characteristics and oxidative stability of oil at relative humidities (RH) from RH approximately 0% to RH 91% at 37 degrees C were analyzed. Oil droplets retained their forms in drying and reconstitution, but the original droplet size of the emulsion was not restored when the powder was dispersed in water. The particles seemed to be covered by a protein-rich surface layer as analyzed by electron spectroscopy for chemical analysis (ESCA). Oxidation of flaxseed oil dispersed in the WPI matrix was retarded from that of bulk oil but followed the same pattern as bulk oil with respect to humidity. A high rate of oxidation was found for both low and high humidity conditions. The lowest rate of oxidation as followed by peroxide values was found at RH 75%, a condition that is likely to diverge significantly from the monolayer moisture value. A weak baseline transition observed for the WPI matrix in a differential scanning calorimetry (DSC) thermogram suggested a glassy state of the matrix at all storage conditions. This was not consistent with the observed caking of the powder at RH 91%. Scanning electron microscopy (SEM) images revealed a considerable structural change in the WPI matrix in these conditions, which was suggested to be linked with a higher rate of oxygen transport. Possible mechanisms for oxygen transport in the whey protein matrix under variable RHs are discussed.     

Antioxidant activity of oregano, parsley, and olive mill wastewaters in bulk oils and oil-in-water emulsions enriched in fish oil

The antioxidant activity of oregano, parsley, olive mill wastewaters (OMWW), Trolox, and ethylenediaminetetraacetic acid (EDTA) was evaluated in bulk oils and oil-in-water (o/w) emulsions enriched with 5% tuna oil by monitoring the formation of hydroperoxides, hexanal, and t-t-2,4-heptadienal in samples stored at 37 degrees C for 14 days. In bulk oil, the order of antioxidant activity was, in decreasing order (p < 0.05), OMWW > oregano > parsley > EDTA > Trolox. The antioxidant activity in o/w emulsion followed the same order except that EDTA was as efficient an antioxidant as OMWW. In addition, the total phenolic content, the radical scavenging properties, the reducing capacity, and the iron chelating activity of OMWW, parsley, and oregano extracts were determined by the Folin-Ciocalteau, oxygen radical absorbance capacity, ferric reducing antioxidant power, and iron(II) chelating activity assays, respectively. The antioxidant activity of OMWW, parsley, and oregano in food systems was related to their total phenolic content and radical scavenging capacity but not to their ability to chelate iron in vitro. OMWW was identified as a promising source of antioxidants to retard lipid oxidation in fish oil-enriched food products.     

Influence of environmental conditions on the stability of oil in water emulsions containing droplets stabilized by lecithin-chitosan membranes

Oil-in-water emulsions containing cationic droplets stabilized by lecithin-chitosan membranes were produced using a two-stage process. A primary emulsion containing anionic lecithin-coated droplets was prepared by homogenizing oil and emulsifier solution using a high-pressure valve homogenizer (5 wt % corn oil, 1 wt % lecithin, 100 mM acetic acid, pH 3.0). A secondary emulsion containing cationic lecithin-chitosan-coated droplets was formed by diluting the primary emulsion with an aqueous chitosan solution (1 wt % corn oil, 0.2 wt % lecithin, 100 mM acetic acid, and 0.036 wt % chitosan). The stabilities of the primary and secondary emulsions with the same oil concentration to thermal processing, freeze-thaw cycling, high calcium chloride concentrations, and lipid oxidation were determined. The results showed that the secondary emulsions had better stability to droplet aggregation during thermal processing (30-90 degrees C for 30 min), freeze-thaw cycling (-10 degrees C for 22 h/30 degrees C for 2 h), and high calcium chloride contents (相似文献   

Alteration of chemical composition and the oxidative stability of bleached pomace-olive oil on activated clays

This work is a contribution to the study of the bleaching process, which is a very important stage in the refining process of vegetable oils and used to reduce or convert undesired constituents to harmless ones from fats and oils. The virgin olive oil, taken as reference, and the pomace-olive oil were bleached in the optimal conditions using Tunisian bleaching earths (South of Tunisia) which were activated in our laboratory and compared with commercial clays. It was shown that activated Tunisian clays are characterized by a very important adsorptive capacity, comparable to that of commercial clays. Also, the physicochemical stability of bleached oils was studied. The fatty acid composition (GC), the triacylglycerol composition (HPLC), and the oxidative stability (UV spectrometry) allowed us to conclude that oils, bleached with the Tunisian activated clays, do not undergo considerable physicochemical alterations and remain corresponding to the international standards for refined oils for human consumption.     

Dynamic interfacial rheology as a tool for the characterization of whey protein isolates gelation at the oil-water interface.

Heat-induced interfacial aggregation of a whey protein isolate (WPI), previously adsorbed at the oil-water interface, was studied by interfacial dynamic characteristics coupled with microscopic observation and image analysis of the drop after heat treatment. The experiments were carried out at temperatures ranging from 20 to 80 degrees C with different thermal regimes. During the heating period, competition exists between the effect of temperature on the film fluidity and the increase in mechanical properties associated with the interfacial gelation process. During the isothermal treatment, the surface dilational modulus, E, increases, and the phase angle, delta, decreases with time to a plateau value. The frequency dependence of E and delta is characteristic of viscoelastic films with increasing delta and decreasing E at lower frequencies. The effects of heat treatment depend on the conditions at which the gelation process takes place. Microscopic observation of gelled films gives complementary information on the effect of heat treatment on WPI adsorbed films.     

Characterization of the antioxidant activity of sugars and polyhydric alcohols in fish oil emulsions

Polyols have been incorporated into fish oil emulsions as a means for the inhibition of lipid oxidation and suppression of fishy flavor. However, the role of sugars and polyhydric alcohols as antioxidants has not been clearly established. Selected polyols were evaluated for their performance as antioxidants and modifiers of oxidation pathways in a model system. Oil/water (O/W) emulsions were prepared with freshly steam-deodorized menhaden oil. A layer of emulsion in aluminum pans held at 5 degrees C was exposed to 2550 lx fluorescent lights for 24 h before peroxide values and volatile flavor compounds were analyzed by GC headspace entrainment procedure. Antioxidant activity was confirmed for fructose, sucrose, raffinose, sorbitol, or mannitol when incorporated at 16% of the aqueous phase into model fish oil-in-water emulsions. Peroxide values were suppressed 10-18% in treated samples compared to control samples. Viscosity data did not exclude possible contributions from a restricted oxygen diffusion mechanism in the antioxidant activity, but revealed that emulsion viscosity did not govern fish oil oxidation rates. Combining polyols with phenolic antioxidants (alpha-tocopherol, BHT, or TBHQ) frequently diminished the antioxidant activity compared to that for individual phenolic antioxidants, which was interpreted as indicating that the H-donating activity of phenolic antioxidants was hindered by the H-bonding activity of polyols. A viscosity-based inhibition of the retroaldol conversion of (E,Z)-2,6-nonadienal to (Z)-4-heptenal with a high fructose concentration (67%) was attributed to a restriction of molecular mobility of reactants, but the conversion was only slightly inhibited by the concentration of fructose (16%) used in experimental emulsions. The data supported a hypothesis that either or both free radical scavenging and transition state metal chelation activities were provided by polyols in fish oil emulsions. Also, polyols retarded the water-requiring retroaldol decomposition of (E,Z)-2,6-nonadienal to (Z)-4-heptenal in the model systems and the reaction may be involved in some suppression of fishy flavors in emulsions.