三种国外木材防腐剂室内防腐防霉防白蚁性能评价

不含铬和砷的TanalithCuAz、Tanalith CY和Totim B是目前国外广泛应用的环保型木材防腐剂产品.本文报道了这3种国外木材防腐剂产品的首次国内室内防腐性能评价试验的结果.结果显示,用少量Tanalith CY和Totim B产品即可有效地抑制腐朽菌对木材的侵害;Tanalith CuAz对腐朽菌的抑制效力随其浓度的增加而快速增大;Tanalith CuAz和Totim B分别显现出良好的抑制白蚁、防止蓝变菌及霉菌侵染的功效.     

心材提取物和专用木材防腐剂作为木材保护剂的相对功效

本文调查了三种耐用木材(Afzelia africana J.E. Smith; Erythrophleum suaveolens (Guill & Perr.) Brenam. Syn. E guinensis G.Don. or Milicia excelsa (Welw) C.C. Berg. Syn. Chlorophora excelsa (Welw) Benth.)的心材提取物（在60%的甲醇中风干提取）和两种专用木材防腐剂（CCA和Penta）在暴露的土壤区组设计条件下，抑制三种木材腐朽菌(Coridopsis Polyzona Klotzch; Lenzites trabea; or Trametes cingulata Fr.)对见血封喉边材的侵袭的相对潜能，并测定其阈值。提取物和防腐剂的剂量分别是8.009、24.778、48.056、96.111、144.167 kg·m-3 ，样品的暴露处理时间与ASTM D1413-72规定的一致分别是14周和18周。结果显示：在阈值范围内，任何一种心材提取物或木材防腐剂在研究中对木材腐朽菌的抑制能力在0.01的显著水平下，差异显著。这些生物杀灭剂的相对功效是取决于真菌的种类。没有任何一种心材提取物或木材防腐剂（除在用最高的存留水平处理被侵袭的非洲毒箭木的条件下）对于被处理的木材能够授予"非常持久"等级。本土树种的心材提取物相对持久力的减少的可能原因是复杂的。在最高的存留量（144.167 kg·m-3）水平下，在0.05显著水平下每种心材提取物和任一种专用木材防腐剂（CCA和Penta）之间的功效差异不显著.     

建筑材用防腐剂配方及其化学性能的试验

我国CCA系列配方与英国CCA(Tanalith C,Celcure K33)的对比试验表明:我国CCA_3、CCA_6配方抗流失和对金属腐蚀效果接近英国产品;砷含量范围低于美国CCA—C型;国产原料配制的CCA_(S)抗流失和对金属腐蚀性较好。浸渍处理试验显示,CCA类防腐剂宜采用加压法。PPA油性防腐剂中的五氯酚溶解度、抗“霜”、油漆性能良好;CCB宜于处理门窗及室内木结构。表层化学浸渍处理可使硼在木材中的保留率提高到60—70%。     

Biological effectiveness of didecyl dimethyl ammonium tetrafluoroborate (DBF) against basidiomycetes following preconditioning in soil bed tests

Evaluation of wood preservatives in soil-contact tests is becoming an important issue since detoxification of wood-protecting compounds by fungi and bacteria found in soil may decrease the resistance of treated wood. In this study, the decay resistance of wood treated with didecyl dimethyl ammonium tetrafluoroborate (DBF), a recently developed quaternary ammonia compound, was evaluated in both soil bed and laboratory decay resistance tests. Small specimens (5×10×100 mm³) of DBF-treated and untreated sugi sapwood were subjected to decay in laboratory soil bed tests (DIN ENV 807 (2001)) followed by Basidiomycetes tests (DIN EN 113 (1996)). Exposure in field soil and compost soil substrates was used to observe the effects of wood degrading and other soil-inhabiting micro-organisms on the decay resistance of the specimens. Soil bed tests showed that DBF-treated wood specimens at 7.7 kg/m³ retention level (1% DBF solution concentration) showed better performance compared to 0.01 and 0.1% DBF treatments. The 7.7 kg/m³ retention level was also effective to protect the wood specimens against Coniophora puteana and Coriolus versicolor in Basidiomycetes tests. It is concluded that detoxification of wood preservatives in soil contact is an important factor to determine protective properties of treated wood in ground contact applications. Further experiments with larger specimens are needed to observe the performance of DBF-treated wood at higher retention levels in field above ground and ground contact tests. Dedicated to Prof. Dr. H.C. Mult. Walter Liese on the occasion of his 80th birthday.     

Efficacy of wood preservatives formulated from okara with copper and/or boron salts

As a substitute for high-cost copper azole (CuAz) and alkaline copper quaternary (ACQ) wood preservatives, alternative wood preservatives were formulated with okara, which is an organic waste from the production of tofu, and copper chloride and/or borax. Each preservative was used in treatment of wood blocks in a reduced-pressure method to measure its treatability. The treated wood blocks were placed in hot water for 3 days to examine the stability of the preservatives against hot-water leaching. The preservatives successfully penetrated into wood blocks, probably due to the use of ammonium hydroxide as a dissociating agent. However, the stability of okara-based preservatives dropped as the concentration of acid in the solutions used for hydrolysis of okara increased. The treatability and leachability of the preservatives were not affected by hydrolysis temperature but were negatively affected by the addition of borax. Leached wood blocks treated with okara-based preservatives and exposed to decay fungi Gloeophyllum trabeum and Postia placenta over 12 weeks showed good decay resistance. Okara-based wood preservatives can protect wood against fungal attack as effectively as CuAz, and have potential for use as environmentally friendly wood preservatives.     

Automated image processing for quantification of blue-stain discolouration of Norway spruce wood

Bioincising is a promising method for enhancing liquid uptake (e.g. preservatives or wood-modification agents) in refractory wood. Incubation with the white-rot fungus, Physisporinus vitreus, which selectively degrades pit membranes, results in deeper and more homogeneous penetration of liquids. Conventional methods of assessing the degree of fungal discolouration of wood after treatment with preservatives (e.g. European standard EN 152) are partly based on a subjective rating scale, which gives a rough value of the surface colonisation by blue-stain fungi. Hence, an automated image processing (AIP) procedure was developed for standardised quantification of the segmentation thresholds of discolouration and tested against manual segmentation analysis. Using the red filter in the AIP method revealed high correlation (R ² 0.95) and allowed for more user friendly and objective determination of blue staining of wood.     

Rapid detection of propiconazole and tebuconazole in wood by solid phase desorption: ion mobility spectrometry

The durability of wood is improved by wood preservatives. Due to new environmental legislation, commonly used active ingredients such as chromium and arsenate are being replaced by alternative and more environmentally friendly preservatives. However, the alternative wood preservatives are more difficult to detect in the wood. Detection of the preservatives is necessary in order to monitor millwork production for qualitative assessment of the wood preservative uptake. The aim of this study is to examine the use of solid phase desorption-ion mobility spectrometry (SPD-IMS) can be used for rapid detection of the wood preservatives propiconazole and tebuconazole in Scots pine (Pinus sylvestris). The findings proved that SPD-IMS is capable of detecting and distinguishing wood preservatives directly from treated wood shavings. SPD-IMS requires no additional sample preparation or extraction of the wood sample. The findings show that SPD-IMS is a fast and easily applied method for direct detection of propiconazole and tebuconazole in small wood samples.     

Dielectric properties of copper-ethanolamine treated Chinese fir (Cunninghamia lanceolata Hook.)

In order to clarify the interaction between copper and wood substances in wood treated with copper containing water-borne wood preservatives, the dielectric constant ε′ and dielectric loss factor ε″ of untreated wood and wood treated with four concentration levels of copper-ethanolamine (Cu-EA) solutions were determined within a temperature range from –100 to 40°C and a frequency range from 100 to 1 MHz. Three dielectric relaxation processes were observed in the ε″ spectrum; among them R-I is based on the reorientation of methylol groups in the amorphous region of wood cell walls and R-II is related to wood extractives. R-III appeared in Cu-EA treated wood, and its magnitude decreases with the concentration of Cu-EA solutions used in this experiment. This relaxation process was considered to be based on the reorientation of copper-ethanolamine-wood complexes in wood cell walls. At low copper retention, the hydrogen in the complex can form hydrogen bonding with adjacent hydroxyl groups, which results in a strong bonding state between copper and wood; at high copper retention, the numerous copper-ethanolamine complexes not only hinder them from forming hydrogen bonding with adjacent wood molecules due to steric hindrance, but also weaken the interaction between wood molecules themselves, which corresponds to reducing ε″ values of both R-I and R-III processes. The results explain the fact of in-creasing copper leaching in wood treated with high concentration copper-based water-borne preservatives.     

Variation in carbon concentration and wood density for five most commonly grown native tree species in central highlands of Ethiopia: The case of Chilimo dry Afromontane forest

ABSTRACT

Information regarding carbon concentration and wood density are lacking in Chilimo dry Afromontane forest.

The aim of this study was to estimate carbon concentration and wood density for Allophyllus abyssinicus, Olea europaea, Olinia rochetiana, Rhus glutinosa, and Scolopia theifolia. A total of 105, 30–50 mm thick wood discs were collected and oven dried at 102°C and 67°C to constant weight, chopped and finally grinded into 0.2 mm with a grinding mill. Carbon concentration was analyzed using the ash method, while wood density was estimated using the water displacement method. The highest carbon concentration (57.12%) was found for O. rochetiana, however, the lowest carbon concentration (56.43%) was found for A. abyssinicus. Stem parts had higher carbon concentration (56.98%) than branch (56.74%) and leave (54.53%) parts. O. europaea exhibited the highest wood density (0.67 g cm^?3) value than other species. However, the lowest wood density (0.42 g cm^?3) was exhibited for A. abyssinicus. Wood density was also showed a decreasing trend along with increases in stem height and maximum wood density (0.62 g cm^?3) was found under stump position, while, the minimum wood density (0.4 g cm^?3) was found under tree commercial height.     

尾叶桉与赤桉正反析因交配杂种F_1材性遗传参数的估算

[目的]通过尾叶桉与赤桉杂种F1材质性状的遗传参数估算及其分析,为桉树杂交育种材性改良亲本选配和交配设计提供理论依据。[方法]以尾叶桉与赤桉6×6正反析因交配杂种F1测定林为材料,并以相应亲本自由授粉的半同胞子代作对照。9年生时,对各小区的杂种和家系(5株小区,6次重复)选取2株平均木,在胸高1. 3 m处沿南北向钻取木芯,共984个,测定木材基本密度、纤维长、纤维宽和纤维长宽比,利用ASReml-R估算4个材质指标的特殊配合力、杂种优势、父母本单株狭义遗传力、遗传相关和表型相关系数。[结果]表明:尾叶桉与赤桉正反交的杂种木材基本密度优于对照,呈明显的杂种优势;反交组合杂种其木材基本密度优于正交组合杂种,正交组合杂种的纤维特性优于反交组合的;在正交组合杂种中,木材基本密度、纤维长和纤维长宽比的母本效应低于父本效应;而反交组合杂种中,4个材质指标的母本效应均高于父本效应。木材基本密度和纤维特性指标受中至低遗传控制。正反交组合杂种中,除纤维长宽比外,其余3个材质指标的显性效应大于加性效应。对于遗传相关,杂种的木材基本密度与纤维宽呈极显著的负相关,与纤维长宽比呈极显著的正相关,与纤维长呈不显著负相关,纤维长与纤维宽呈显著正相关。对于表型相关,除纤维宽与纤维长宽比呈不显著正相关外,其余性状间均呈极显著正相关。[结论]尾叶桉与赤桉杂种的材质性状遗传差异因亲本和交配方式而异,表明通过种间杂交和正向选择进行材质性状的遗传改良具有潜力。     

Corrosion of metal fasteners embedded in acetylated and untreated wood at different moisture contents

ABSTRACT

Acetylated wood is now commercially available and designed to be used in certain outdoor applications as an alternative to preservative-treated wood. Fastener corrosion can be a concern in preservative treated wood when the wood remains wet for long periods. However, little data on the corrosiveness of acetylated wood exists beyond the product literature. Here we examine the corrosiveness of commercially obtained acetylated wood and compare it against unmodified (untreated) southern pine (Pinus spp.). Corrosion rates of plain carbon steel, hot dip galvanized steel, and stainless steel were calculated gravimetrically after a one year exposed in the wood. Four different moisture conditions were examined: 90% relative humidity (RH), 95% RH, 100% RH, and a fully water saturated condition. When compared to literature data on the corrosion of fasteners in preservative treated wood at 100% RH, the acetylated wood had much lower steel corrosion rates than all preservatives examined; the measured corrosion rates for galvanized steel were lower than all preservatives except chromated copper arsenate. These measured corrosion rates across a range of moisture conditions can be used to inform the selection of appropriate corrosion resistant fasteners when building with acetylated wood.     

Survival,growth, wood basic density and wood biomass of seven-year-old Casuarina species/provenances grown at Kongowe,Kibaha, Tanzania

A performance comparison of seven-year-old individuals of 13 Casuarina species/provenances in terms of survival, growth (diameter, height and volume), wood basic density and wood biomass was undertaken at Kongowe, Kibaha, Tanzania. The trial was laid out using a randomised complete block design with four replications. The results showed significant differences (P < 0.0001) in all parameters. Casuarina equisetifolia from Montazah National Park, Egypt, had the lowest untransformed survival (48.8%), whereas C. equisetifolia from Wagait Tower (North Timor), Indonesia, had the highest survival (87.5%). Casuarina equisetifolia from Montazah National Park, Egypt, had the lowest mean diameter (8.6 cm) while the C. junghuhniana provenance from Timor, Indonesia (seedlot no. 19489) had the highest diameter (14.8 cm). Casuarina equisetifolia from Montazah National Park, Egypt, had the lowest mean height (16.2 m), volume (22.1 m³ ha^?1) and biomass production (23.5 t ha^?1), whereas C. equisetifolia from Hadsamira Songkhla, Thailand, had the highest mean height (24.3 m), volume (66.4 m³ ha^?1) and biomass production (72.9 t ha^?1). In terms of wood basic density, the C. junghuhniana provenance from Timor, Indonesia (seedlot no. 19489) had the lowest (617 kg m^?3), whereas C. equisetifolia from Wagait Tower (North Timor), Indonesia, had the highest (731 kg m^?3). Ordinal ranking for the best-performing species/provenances revealed that the best two provenances were C. equisetifolia from Hadsamira Sonkhla, Thailand, and C. junghuhniana from Timor, Indonesia (seedlot no. 19491). The two poorest-performing provenances were C. equisetifolia from Montazah National Park, Egypt, and C. equisetifolia from Cotonou, Benin. The outstanding species/provenances are recommended for pilot planting at Kibaha and similar sites.     

In vitro decay of Aextoxicon punctatum and Fagus sylvatica woods by white and brown-rot fungi

Summary The in vitro decay of Aextoxicon punctatum and Fagus sylvatica wood by the fungi Trametes versicolor, Ganoderma australe, Phlebia chrysocrea and Lentinus cyathiformis was studied by the agar-block method, and then the decayed woods were analyzed by chemical and spectroscopic techniques. The results demonstrated the strong resistance of the A. punctatum wood to the brown-rot fungus L. cyathiformis; the resistance might be related to the low S/G lignin ratio in this Austral hardwood. Wood decay by the Austral white-rot fungi G. australe and P. chrysocrea was rather limited, and preferential degradation of lignin was not produced although all the fungi studied increased wood digestibility. The most characteristic white and brown-rot decay patterns were observed during the in vitro decay with T. versicolor and L. cyathiformis, respectively. Trametes versicolor caused high weight losses and reduced the lignin content of the wood, whereas L. cyathiformis produced a preferential removal of xylan. No important changes in the solid-state ¹³C NMR spectra were observed after wood degradation by T. versicolor, but this technique evidenced an increase in aromatic carbon by L. cyathiformis. This increase was higher than that found in the Klason lignin content, suggesting the presence of altered lignin fractions in the brown-rotted wood.The authors are indebted to Prof. H. D. Lüdemann for the facilities at the Institut für Biophysik und physikalische Biochemie (Regensburg), to A. Navarrete (INIA, Madrid) for her collaboration, and to C. F. Warren (ICE, Alcalá de Henares) for her linguistic assistance. The computer program for spectra treatment was developed by G. Almendros (Centro de Ciencias Medioambientales, CSIC, Madrid). This investigation has been funded by the Spanish Biotechnology Program (Grant BIO88-0185)     

Growth of ten multipurpose tree species on acid soils in Sangmelima,Cameroon

Ten multipurpose tree species were planted both in monoculture and intercropped withArachis hypogea (groundnut) in a randomized complete block with three replications. The vigrou, biomass, nutrient content, and coppicing percentage of the trees were evaluated. Intercropping with groundnuts during the establishment phase did not affect subsequent growth and development of the species.Acacia mangium, Acacia auriculiformis, Cassia siamea, Calliandra calothyrsus andParaserianthes falcataria established well, when compared toGliricidia sepium, Leucaena leucocephala, Dialum guineense, Dubocia macrocarpa andMilicia excelsa. A. mangium, A. auriculiformis, C. calothyrsus, C. siamea andP. falcataria produced the highest leaf (4 to 20 t ha^–1) and wood (12 to 37 t ha^–1) biomass yield (primary growth) at one to three years after planting. Coppicing percentage ofA. mangium A. auriculiformis andP. falcataria were relatively low (35 to 50%).C. calothyrsus andC. siamea showed the highest coppicing percentage (95 to 100%) and produced the greatest coppice biomass (9 to 13 t ha^–1). Total nitrogen and organic matter percentage of soils from under the stands of these two species were also significantly higher than that of the rest. The two species may thus be considered for use in agroforestry technologies for soil improvement on acid soils, which are typical of the moist tropics.     

Enzymatic saccharification and ethanol production of <Emphasis Type="Italic">Acacia mangium</Emphasis> and <Emphasis Type="Italic">Paraserianthes falcataria</Emphasis> wood,and <Emphasis Type="Italic">Elaeis guineensis</Emphasis> trunk

We examined the saccharification and fermentation of meals from Acacia mangium wood, Paraserianthes falcataria wood, and Elaeis guineensis trunk. The levels of enzymatic hydrolysis of cellulose and ethanol production were highest for P. falcataria wood and lowest for A. mangium wood. Ultrasonication pretreatment of meal further increased the rates of hydrolysis and ethanol production in meal from P. falcataria wood. Through this pretreatment, hemicelluloses (xylan and xyloglucan) and cellulose were released in the meal from P. falcataria wood. Loosening of hemicellulose associations can be expected to make P. falcataria wood more useful for bioethanol production.     

Adhesive performance of woods treated with alternative preservatives

The extended use of woods treated with traditional or alternative preservatives for exterior applications requires an assessment of wood adhesive performance. This study attempts to evaluate the performance of wood adhesives for woods treated with various waterborne preservatives. Two softwood species, i.e. Korean pine (Pinus koraiensis Sieb. et Zucc.) and Japanese Larch (Larix leptolepis [Sieb. et Zucc.] Gordon) were treated with copper–chrome–arsenic (CCA), CB-HDO, or copper azole (CY), and then bonded with four different wood adhesives such as urea–melamine–formaldehyde (UMF) resin, melamine–formaldehyde (MF) resin, phenol–formaldehyde (PF) resin, and resorcinol–formaldehyde (RF) resin. The performance of these adhesives was evaluated by measuring the dry shear strength of adhesive-bonded wood block on compression. Both UMF and MF resins produced a relatively strong adhesive strength for CY-treated pine and larch woods. The PF resin also produced good bond strength when bonded with either larch wood treated with CY or pinewood treated with CB-HDO. The best result was obtained when the CB-HDO-treated woods were bonded with RF resin. For a better bond strength development, a proper combination of adhesive, preservative, and wood species should be selected by taking into consideration of the characteristics of these three parameters as well as their interactions.     

Methods for the determination of wood properties,Kraft pulp yield and wood fibre dimensions on small wood samples.

A trial set-up with methods for sampling, treatment and analysis of small wood chips are presented in this paper, to determine important wood and fibre properties, like basic density, dry density, volume swelling of wood, Kraft pulp yield, fibre length, fibre coarseness, fibre width, lumen width and fibre wall thickness. The required time for one sample is about 1.5 man-hour, but this requires relatively larger series and trained personnel. Acceptable measurement accuracy is achieved when the volume of the wood sample is at least 1.5 ml, except that of wood volume swelling. To gain acceptable measurement accuracy for volume swelling, the wood volume should be increased to at least 3 ml, and preferably more than 5–6 ml per sample. The level of pulp yield and wood density do not show a significant effect on the measurement accuracy for fibre cross-section dimensions. Fibre coarseness, on the other hand, has a significant influence on these accuracies. A double measurement of fibre coarseness will improve the accuracy to an acceptable level. The method presented here may, together with information about trees and growth locations, form the basis for greater insight into the mechanisms involved in development of wood and fibre properties in trees, which in turn may provide better control and utilisation of wood for pulp and paper production.Abbreviations CWD cell wall density in dry wood=1500 kg/m³ - Ww dry weight of wood (kg) - Vmax green (wet) volume of wood (m³) - Vmin dry volume of wood (m³) - BD basic wood density (kg/m³) - DD dry wood density (kg/m³) - VS maximum volume swelling of wood (%) - Wp dry weight of pulp (kg) - PY pulp yield (%) - C fibre coarseness, the average weight of a unit length of fibre (g/m) - CL average chip length (mm) - CWT average cell wall thickness (m) - FW average fibre width (m) - l average native fibre length in solid wood - L chip length - lc average fibre length in wood chip (mm) - Lc length-weighted fibre length in wood chip (mm) - lw native average fibre length in wood (mm) - Lw native length-weighted fibre length in wood (mm) - LW average lumen width (m) - llw average native fibre length, length weighted, in wood - X average fibre length in chip - Xlw average fibre length, length weighted, in chip     

Lignin characterization of triploid clones of Populus tomentosa Carr.

In order to understand the structural characteristics of lignin in triploid clones of Populus tomentosa and its changes in the processes of pulping and bleaching, milled wood lignin (MWL), lignin carbohydrate complex (LCC) and the residual lignin from kraft pulp (KP) and sulfite pulp (SP) were isolated and analyzed by Fourier transform infrared (FTIR) spectrum and ¹³C nuclear magnetic resonance (NMR). The most diagnostic peaks were assigned and the differences were discussed. The spectral patterns reveal that triploid P. tomentosa shows the specific features of hardwood from temperate areas, but in the spectrum of FTIR, the strength ratio of A 1270 cm⁻¹ to A1226 cm⁻¹ is 0.88, higher than the average of hardwood from temperate areas, which will make the lignin delignification more difficult during pulping and bleaching. The LCC from triploid P. tomentosa is mainly composed of xyloglucan and glucuronic acid, and other glucides have much lower ratio. In LCC FTIR, there are three peaks at 1 427, 1 329 and 1 046 cm⁻¹, indicating that both semi-cellulose and cellulose could exist in LCC, and that there might be relationships between cellulose and lignin. Compared with the residual lignin from KP and SP, the condensed structure in KP is more than that in SP.     

Genetic variation in wood color and its correlations with tree growth and wood density of <Emphasis Type="Italic">Calycophyllum spruceanum</Emphasis> at an early age in the Peruvian Amazon

Calycophyllum spruceanum (Benth.) Hook. f. ex K. Shum. is an important timber-tree species in the Peruvian Amazon Basin. Markets currently prefer wood with a uniform, light yellow color, but these preferences may change in the future. As farmers and industry commonly use wood from young trees, it is important to investigate genetic and environmental variation in juvenile-wood properties to assess whether tree improvement programs could make adjustments to changing preferences. A provenance/progeny test was established to evaluate genetic variation in growth and wood properties of young trees, the strength of their genetic control as well as their interrelationships both at the genetic and the phenotypic level in different planting zones. This paper presents analyses of variation in wood color at 39 months, and their correlations with tree growth and wood basic density. CIELab means for lightness ranging from black to white (L), green to red hues (a*) and blue to yellow hues (b*) were 67.63, 5.34 and 22.12, respectively; means for chroma (C) and hue angle (h)* were 22.76 and 76.43, respectively (C and h* were estimated from a* and b*). Significant variation due to provenances and especially due to families within provenances was found in some wood color characteristics, and some color characteristics also differed significantly among planting zones. Genetic correlations indicate that, in general, selection of faster growing trees and/or trees with denser wood would have little effect on wood color and its uniformity. In general, wood color had relatively low heritability (h _i ²): among all trees, h _i ² = 0.31 for L; and variance due to families was not significant for a* and b*. Genetic control of color was highest in the planting zone where trees grew most rapidly: h _i ² = 0.48 and 0.52 for a* and b*, respectively; but variance due to families was not significant for L. Results suggest that selection based on wood color would be more effective in zones with more fertile soils and higher rainfall.      

Serial exposure technique for assessing performance of wood preservatives

Summary The performance of copper-chrome-arsenate (CCA) and two quaternary ammonium compounds as wood preservatives was compared using a serial exposure technique, involving successive 10-week exposures in conventional soil jars. All preservative treatments were successful in preventing decay of Pinus radiata sapwood after the first exposure, but successive 10-week exposures clearly distinguished those treatments likely to offer long-term protection. The progressively increasing times of exposure with test fungi overcame the time lag for decay initiation in wood treated to preservative retentions above the toxic threshold established by conventional laboratory methods. Consequently, an additional and higher toxic threshold could be calculated. Examination of data from field stake tests suggested that a series of toxic thresholds established by a serial exposure technique could be related to preservative retentions which protect wood in the field from decay for increasing periods of time. Results of all tests are discussed in relation to the development of a laboratory procedure which may predict field performance of wood preservatives.