Effects of borate impregnation on the response of wood strength to heat treatment

Based on the strong correlation between acidity and thermal degradation in wood reported in previous studies, the effect of borate impregnation as an alkali-buffering medium was investigated on the strength properties of thermally modified wood. Wood samples were impregnated with 0.1 M Sodium borate solution (pH=9) before they were subjected to heat treatment at temperatures of 180°C and 200°C for durations of 2 and 4 h. The borate impregnation results in some reductions in the severity of strength loss during heat treatment and this is invariably due to buffering effect of the alkali on the acidity of wood, which could have mitigated the degree of degradation. The positive effects of borate impregnation as a pretreatment on the strength properties of heat-treated wood depend on the degree of heat treatment. Hence, the use of borate impregnation as a pretreatment method for heat treatment is recommended only where a relatively mild heat treatment is involved.     

Determination of optimum borate concentration for alleviating strength loss during heat treatment of wood

Based on the already established mitigating potentials of borate salt on the negative effects of heat treatment on the strength properties of wood (Awoyemi and Westermark 2005), the optimum concentration of the alkali buffer solution required to minimize strength loss was determined. Wood samples were impregnated with 0.1, 0.3 and 0.5 M sodium borate solution and exposed to heat treatment for 4 h at 200°C. The mitigating effect of borate salt on the degree of strength loss during heat treatment increases significantly with increasing concentration from 0.1 to 0.3 M. Increasing the concentration of sodium borate from 0.3 to 0.5 M did not produce significant differences in the degree of strength loss during heat treatment. The increase in the buffering effect observed with increasing concentration of the sodium borate preservative is more pronounced on the modulus of rupture than on the modulus of elasticity. It is evidenced therefore that the buffering effect of borate salt on the modulus of elasticity of wood exposed to heat treatment did not start significantly until the 0.3 M concentration is reached and further increase in concentration beyond this point did not produce any appreciable improvement in strength properties.     

Physical properties and termite durability of maritime pine Pinus pinaster Ait., heat-treated under vacuum pressure

An original heat treatment performed under vacuum pressure was investigated. Maritime pine samples were treated at six different temperatures: 140, 160, 180, 200, 230 and 260°C. The physical and mechanical consequences, i.e. bending strength (MOR), modulus of elasticity (MOE), hygroscopic behaviour, equilibrium moisture contents and anti-swelling efficiency (ASE) were studied. A no-choice feeding test according to the NF EN 117 standard was achieved. Temperatures up to 200°C had no significant effect on wood properties. However, at 230 and 260°C, the decrease in MOR was severe, reaching 42.5 and 62.5%, respectively. Whatever the treatment conditions, wood samples were still highly degraded by termites, revealing no increase in their durability.     

Determination of formic-acid and acetic acid concentrations formed during hydrothermal treatment of birch wood and its relation to colour, strength and hardness

Formation of benzyl esters from acetic and formic acids during heat treatment of birch at 160–200°C has been studied by gas chromatography. High concentrations of formic and acetic acids formed by the wood itself during hydrothermal treatment were found. The concentrations of acids increased with both treatment time and temperature. The maximum formic- and acetic acid concentrations found at 180°C and after 4 h of treatment performed in this work were 1.1 and 7.2%, based on dry-weight wood, respectively. The treated wood material was characterised by mechanical testing [bending tests perpendicular to the grain, modulus of rupture, modulus of elasticity, Brinell hardness, impact bending and colour measurements (CIE colour space)]. The experiments, where high concentration of acids was formed, showed severe losses in mass and mechanical strength. Indications of possible enhanced mechanical properties for the treated, compared with untreated birch wood were found around 180–200°C at short treatment times. This paper discusses possible degradation reactions coupled with the colour and mechanical properties in relation to acid formation, and suggestions for process optimisations.     

Strength properties of thermally modified softwoods and its relation to polymeric structural wood constituents

Thermal modification at relatively high temperatures (ranging from 150 to 260 °C) is an effective method to improve the dimensional stability and resistance against fungal attack. This study was performed to investigate the impact of heat treatment on the mechanical properties of wood. An industrially-used two-stage heat treatment method under relative mild conditions (< 200 °C) was used to treat the boards. Heat treatment revealed a clear effect on the mechanical properties of softwood species. The tensile strength parallel to the grain showed a rather large decrease, whereas the compressive strength parallel to the fibre increased after heat treatment. The bending strength, which is a combination of the tensile stress, compressive stress and shear stress, was lower after heat treatment. This decrease was less than the decrease of only the tensile strength. The impact strength showed a rather large decrease after heat treatment. An increase of the modulus of elasticity during the bending test has been noticed after heat treatment. Changes and/or modifications of the main wood components appear to be involved in the effects of heat treatment on the mechanical properties. The possible effect of degradation and modification of hemicelluloses, degradation and/or crystallization of amorphous cellulose, and polycondensation reactions of lignin on the mechanical properties of heat treated wood have been discussed. The effect of natural defects, such as knots, resin pockets, abnormal slope of grain and reaction wood, on the strength properties of wood appeared to be affected by heat treatment. Nevertheless, heat treated timber shows potential for use in constructions, but it is important to carefully consider the stresses that occur in a construction and some practical consequences when heat treated timber is used.     

Effects of nano-silver impregnation on brittleness, physical and mechanical properties of heat-treated hardwoods

The present study investigates the effect of heat treatment of untreated and nano-silver-impregnated Populus nigra, Populus deltoides and Fagus orientalis on the physical and mechanical properties. Specimens were impregnated with a 200-ppm aqueous silver nanoparticles suspension. Heat treatment was carried out at temperatures of 135 ± 3 °C and 185 ± 3 °C. Nano-silver impregnation aggravated the effects of heat treatment. Although significant in some cases, nano-silver impregnation did not seem to have great effect on physical properties. It may be concluded that although NS impregnation aggravated the effects of heat treatment on solid woods, other factors may also be involved such as the species and density of the wood.     

Effect of heat treatment temperature and time on sound absorption coefficient of <Emphasis Type="Italic">Larix kaempferi</Emphasis> wood

Heat treatment improves the dimensional stability and hydrophobicity of wood, and heat-treated wood is currently attracting attention as a new interior material. However, there are few evaluations where the acoustic properties of heat-treated wood are reported when such wood is used as an interior material. In this study, Larix kaempferi wood, typically used as a building material, was heat-treated at 200, 220, and 240 °C for 9, 12, 15, and 18 h. The sound absorption coefficients of the treated wood samples were measured at 250, 500, 1000, 2000, and 4000 Hz in a reverberation room. The sound absorption coefficient increased with the treatment temperature and the treatment time. The results of this study showed that the high-frequency band range sound absorption coefficient of wood can be increased dramatically by heat treatment.     

Effects of heat treatment and impregnation with zinc-oxide nanoparticles on physical,mechanical, and biological properties of beech wood

Effects of zinc-oxide nanoparticles on physical and mechanical properties, as well as biological resistance of untreated and heat-treated beech wood were investigated in this study. Test specimens were prepared from sapwood and impregnated with a 5,000-ppm nano-zinc-oxide (NZ) suspension with a size ranging from 10 to 80 nm at 2.5 bars of pressure and using the Rueping process for 20 min. Control (C) and nano-zinc-oxide-impregnated specimens after (NZA) and before (NZB) heat treatment were divided into four subgroups of unheated (C and CNZ), heated at 50, 145 and 185 °C. Heat treatment resulted in a significant decrease in mechanical strength at temperatures of 145 and 185 °C. Heat-treated specimens showed less dimensional instability and fungal degradation. Impregnation with nano-zinc resulted in a slight and significant increase in weight loss and biological resistance against Trametes versicolor. The results showed that the impregnation significantly decreased the water absorption of the specimens. Impregnation before heat treatment showed considerable effect on the properties of wood compared to that of untreated ones.     

High-temperature mechanical properties and thermal recovery of balsa wood

This article presents an experimental study into thermal softening and thermal recovery of the compression strength properties of structural balsa wood (Ochroma pyramidale). Balsa is a core material used in sandwich composite structures for applications where fire is an ever-present risk, such as ships and buildings. This article investigates the thermal softening response of balsa with increasing temperature, and the thermal recovery behavior when softened balsa is cooled following heating. Exposure to elevated temperatures was limited to a short time (15 min), representative of a fire or postfire scenario. The compression strength of balsa decreased progressively with increasing temperature from 20° to 250°C. The degradation rates in the strength properties over this temperature range were similar in the axial and radial directions of the balsa grains. Thermogravimetric analysis revealed only small mass losses (<2%) in this temperature range. Environmental scanning electron microscopy showed minor physical changes to the wood grain structure from 190° to 250°C, with holes beginning to form in the cell wall at 250°C. The reduction in compression properties is attributed mostly to thermal viscous softening of the hemicellulose and lignin in the cell walls. Post-heating tests revealed that thermal softening up to 250°C is fully reversible when balsa is cooled to room temperature. When balsa is heated to 250°C or higher, the post-heating strength properties are reduced significantly by decomposition processes of all wood constituents, which irreversibly degrade the wood microstructure. This study revealed that the balsa core in sandwich composite structures must remain below 200°–250°C when exposed to fire to avoid permanent heat damage.     

Effects of heat treatment on brittleness of <Emphasis Type="Italic">Styrax tonkinensis</Emphasis> wood

A new approach is proposed for the evaluation of the brittleness of heat-treated Styrax tonkinensis wood. Heat treatment made wood more brittle when wood was heated at a higher temperature or for a longer time. The brittleness increased to four times that of the control when wood was heated at 200°C for 12 h. For treatment at 160°C, the increase in brittleness without any change in weight is thought to be possibly caused by the relocation of lignin molecules. At higher temperatures, loss of amorphous polysaccharides due to degradation is thought to become the main factor affecting brittleness. The crystallites that were newly formed after 2 h of treatment showed brittleness that was different from that of the inherent crystallites remaining after 12 h of heat treatment. This inherent crystalline cellulose possibly plays a role in brittleness. There is also the possibility of using color to predict the brittleness of heat-treated wood.     

Superheated steam treatment of rubberwood to enhance its mechanical,physiochemical, and biological properties

ABSTRACT

This research was aimed to investigate mechanical properties, color and cell-wall components changes, and durability of pre-dried rubberwood (Hevea brasiliensis) after superheated steam (SS) treatment. Wood samples were treated at different SS temperatures (140–180°C) for 1–3?h. The highest compression strength parallel-to-grain, hardness and impact strength were found for samples treated at 160°C for 3?h (30.7% higher than untreated), at 150°C for 1?h (26.6% higher than untreated) and at 150°C for 2?h (52.6% higher than untreated), respectively. The surface color became darker after each treatment in comparison with the untreated wood. The number of accessible hydroxyl groups decreased and the relative cellulose crystallinity increased with SS temperature, indicating decreased hygroscopicity of the treated wood. Also, SEM micrographs of wood surface showed consistent decrease in starch particles with treatment temperature. Both decay and termite resistances of treated rubberwood improved with treatment temperature. All the analyzes showed that dried rubberwood treated with SS had some improvements in the mechanical properties, decreased hygroscopicity, and increase resistance to decay.     

Effects of impregnation and heat treatment on the physical and mechanical properties of Scots pine (Pinus sylvestris) wood

Wood modification, of which thermal modification is one of the best-known methods, offers possible improvement in wood properties without imposing undue strain on the environment. This study investigates improvement of the properties of heat-treated solid wood. Scots pine (Pinus sylvestris) was modified in two stages: impregnation with modifiers followed by heat treatment at different temperatures. The impregnation was done with water glass, melamine, silicone, and tall oil. The heat treatment was performed at the temperatures of 180°C and 212°C for three hours. The modified samples were analyzed using performance indicators and scanning electron microscope micrographs. The mechanical and physical properties were determined with water absorption, swelling, bending strength, and impact strength tests. All the modifiers penetrated better into sapwood than hardwood; however, there were significant differences in the impregnation behavior of the modifiers. As regards the effect of heat treatment, generally the moisture properties were improved and mechanical strengths impaired with increasing treatment temperature. In contrast to previous studies, the bending strength increased after melamine impregnation and mild heat treatment. It is concluded that the properties of impregnated wood can be enhanced by moderate heat treatment.     

Physical and mechanical properties and colour changes of fast-growing Gympie messmate wood subjected to two-step steam-heat treatments

This study aimed to evaluate physical and mechanical properties and colour changes of fast-growing Gympie messmate wood subjected to two-step steam-heat treatments. To achieve this, Gympie messmate wood was thermally treated under different conditions. Combined steam (127°C and ～0,1471 MPa) and heat treatments in an oven (180–240°C for 4 hours) were performed. Physical and mechanical properties were evaluated by weight loss, equilibrium moisture content, specific gravity, volumetric and linear swelling and static bending tests, while colour changes were studied using CIEL*a*b* technique. The main findings showed that the steam pre-treatment in autoclave influenced most of the technological properties evaluated, mainly for heat treatments performed in low temperatures (180–200°C). The most significant changes after thermal treatments were observed for dimensional stability, which increased as a function of temperature of treatment. On the other hand, mechanical strength of thermally modified wood was significantly affected, while stiffness did not change. Colour modifications due to the application of two-step steam-heat treatments confirm the possibility to using these samples for aesthetic purposes.     

Oleothermal modification of fir wood with a combination of soybean oil and maleic anhydride and its effects on physico-mechanical properties of treated wood

This research work aimed at studying the effects of oleothermal modification of fir wood by using combined soybean oil with maleic anhydride (OHT–MA) to achieve lower treatment temperatures and enhance physico-mechanical properties. Wood blocks were oleothermally treated with soybean oil and OHT–MA at five different treatment temperatures (100, 120, 140, 160 and 180 °C) for three different holding times (30, 60 and 180 min). Afterward, physical and mechanical properties of the treated samples were determined, i.e., density, water absorption and volumetric swelling as the physical properties and bending strength, compression parallel to grain and impact load resistance as the mechanical properties. Results revealed increases in densities and reduction in water absorption as well as volumetric swelling of all treated samples. The mechanical properties were affected by OHT–MA treatment at different temperatures. Bending modulus of elasticity as well as compression parallel to grain was increased due to OHT–MA treatment. In addition, there was less reduction in impact load resistance of the treated samples. It was revealed that the OHT–MA enhanced wood properties at low treatment temperatures as well as shorter holding times.     

Changes of chemical properties and the water vapour sorption of <Emphasis Type="Italic">Eucalyptus pellita</Emphasis> wood thermally modified in vacuum

The aim of this study was to evaluate the chemical composition and the dynamic water vapour sorption properties of Eucalyptus pellita wood thermally modified in vacuum. For this purpose, wood samples were thermally modified in a vacuum oven at 160–240 °C for 4 h. Chemical composition were investigated by wet chemical analysis, elemental analysis, as well as Fourier transform infrared (FTIR) analysis, and dynamic water vapour sorption properties were evaluated by dynamic vapour sorption apparatus. The results showed that holocellulose and alpha-cellulose contents decreased and lignin and extractives contents relatively increased during the heat process. Elemental analysis showed a reduction in hydrogen content and an increase in carbon content. FTIR analysis indicated that the degradation of hemicellulose and condensation reactions of lignin occurred. In addition, the thermo-vacuum resulted in a reduction in the equilibrium moisture content of wood during the adsorption or desorption process. And the sorption hysteresis had a decreasing trend with increasing treatment temperature. The development of the hygroscopicity was related to the increase in the relative content of lignin, the degradation of the carbonyl groups in xylan and the loss of carbonyl group linked to the aromatic skeleton in lignin after heat treatment.     

Compressive deformation of wood impregnated with low molecular weight phenol formaldehyde (PF) resin V: effects of steam pretreatment

This study evaluated the potential of steam pre-treatment for making highly compressed phenol-formaldehyde (PF) resin-impregnated wood at a low pressing pressure. Sawn veneers of Japanese cedar (Cryptomeria japonica) were first subjected to saturated steam at different steaming temperatures (140°-200°C), followed by impregnation with a 20% low molecular weight PF resin aqueous solution resulting in a weight gain of around 50%-55%. Four oven-dried treated veneers were laminated and compressed up to a pressing pressure of 1 MPa at a pressing temperature of 150°C and pressing speed of 5 mm/min, and the pressure was held for 30 min. Steam treatment, causing partial hydrolysis of hemicellulose, accelerated the compressibility of Japanese cedar in the PF resin-swollen condition. As a consequence, a discernible increment in density was achieved at a pressing pressure of 1 MPa due to steam pretreatment between 140° and 200°C for 10 min. It was also found that even a short steaming time such as 2 min at 160°C is sufficient for obtaining appreciable compression of PF resin-impregnated wood. The density, Young’s modulus, and bending strength of steam-treated (200°C for 10 min) PF resin-impregnated wood composite reached 1.09 g/cm³, 20 GPa, and 207MPa, respectively. In contrast, the values of untreated PF resin-impregnated wood composite were 0.87 g/cm³, 13 GPa, and 170MPa, respectively.     

Thermal-death kinetics of the bark beetle (Dendroctonus armandi; Coleoptera: Scolytidae)

Data on thermal-death kinetics of bark beetles are essential to develop phytosanitary heat treatments for pine wood and pine wood packaging materials. Using a heating block system, effects of different heating rates between 44 and 50°C at 2°C intervals on destruction of Dendroctonus armandi adult insect were examined. Heat resistance of the insects was found to increase at low heating rates (0.1 or 0.5°C/min). Therefore, the thermal-death kinetics of the beetles were determined at a high heating rate of 5.0°C/min which simulated the rapid dielectric heating of wood products. Results showed that the thermal death curve of D. armandi followed a zero-order reaction kinetic model, indicating the heat destruction rate of the beetle at different treatment temperatures to be independent of their population size. The required thermal holding times to result in destruction of the entire population were 40, 8, 4, and 2?min at 44°C, 46°C, 48°C, and 50°C, respectively. The evaluated thermal-death kinetic data are useful in developing effective beetle elimination quarantine protocols for the wood. A 50°C ?2?min heat treatment with a heating rate of ～5°C/min can be effectively used for disinfesting bark wood materials.     

Effects of temperature and moisture content on selected wood mechanical properties involved in the chipping process

The effects of temperature and moisture content on selected mechanical properties associated with the chipping process were evaluated. In chipping, mechanical properties such as shear parallel to the grain, cleavage, and bending are involved. Matched samples of heartwood and sapwood were obtained from freshly harvested logs of black spruce and balsam fir to determine the variation of the studied mechanical properties between ?30 and 20 °C, at intervals of 10 °C. Moisture content (MC), basic density (BD), and annual ring width (RW) were measured for each sample. For both wood species, temperature had a significant effect on all mechanical properties under freezing conditions (below 0 °C). This effect was more important for sapwood than for heartwood, which was explained by the difference in MC between these two types of wood. Between 0 and 20 °C, temperature and type of wood did not show any significant effect on the mechanical properties. Multiple regression models were obtained to predict the mechanical properties. These regressions showed that MC was the most important factor to explain the mechanical properties below 0 °C. However, for temperatures of 0 °C and higher, BD was the principal factor to predict the mechanical properties. RW was not a significant factor to predict any mechanical property. Cleavage was the most sensitive one to changes in temperature followed by shear, modulus of rupture, and modulus of elasticity. These results could be of great importance in the chipping process.     

Effects of surface modification methods on mechanical and interfacial properties of high-density polyethylene-bonded wood veneer composites

To improve interfacial adhesion between wood veneer and high-density polyethylene (HDPE) film, wood veneer was thermally modified in an oven or chemically modified by vinyltrimethoxysilane. The wood veneers were used to prepare plastic-bonded wood composites (PBWC) in a flat-press process using HDPE films as adhesives. The results showed that both modifications reduced veneer hydrophilicity and led to enhancement in shear strength, wood failure, and water resistance of the resulting PBWC. The thermal treatment significantly decreased the storage modulus close to 130 °C (the melting temperature of plastic). Thermal-treated wood veneer maintains mechanical interlocking for bonding and veneer strength which then declined under thermal treatment due to hemicellulose degradation and cellulose de-polymerization. In the silane-treated PBWC, enhanced interlocking and a stronger bonding structure resulted from the reaction between the silane-treated veneer and HDPE. This strong bonding structure allowed thermal stability improvement demonstrated by high modulus and low tanδ values. However, the strength of silane-treated PBWC was still much lower than thermosetting resin-bonded composites at higher temperatures due to the melting behavior of thermoplastic polymer, precluding its use in certain applications.     

Changes in the microstructure of birch wood after hydrothermal treatment

Birch wood (Betula pendula) samples were treated in a thermal regime (140, 160, 180 °C) for 1 h and investigated by means of scanning electron microscopy (SEM). SEM microimages of the wood cross-section were taken from one and the same place before and after the thermal treatment (magnification 100–2,000×). The results of measurements of areas and linear sizes of the birch wood cells show significant changes, which depend on the thermal treatment conditions and the type of the cell: libriform, tracheid, vessel and ray. After the treatment at 180 °C, the integrity of wood morphological structure begins to break up. Voids and cracks are formed between fibres, thus leading to a decline in the mechanical properties of the wood.